Search Documents

Flawed mining studies have been major contributors to poor investment decisions in mining for many years, contributing to the long period of poor industry profitability. Most of the major mining houses have now adopted quite formal processes and quality standards for mining studies to reduce the potential for poor investment decisions in the future. Other organisations such as the World Bank also have specific requirements for particular types of studies, such as bankable studies. This increasing requirement for rigour and discipline means a highly structured and phased sequence of studies is now required along with the development and adoption of industry-wide standards in mine ventilation studies. New terms in the study process such as ?independent peer review? and ?hold and review? are assisting in this process. More traditional terms such as ?feasibility study? and ?pre-feasibility study? now have much more precise technical definitions. Specific standards for the ventilation components of the various phases of a mining study are proposed in this paper.

Jan 1, 2009

By B Mohanty, G Yamin

A number of parameters, aside from blast design and pre-existing rock conditions, can change the performance of the explosives system in actual blasting practice. Sympathetic pressures caused by detonation of preceding holes have been identified as a major contributor to explosive system malfunctions, leading to uneven blasting performance. These effects can occur both within a hole or across several holes. These can consist of high transient pressures related to the shock phase of the explosion or the relatively longer or quasi-static pressures associated with the explosion gas expansion phase. This study presents the findings from an on- going investigation on measurement and analysis of these pressures between donor and receptor holes in a granitic outcrop for representative inter-hole distances and borehole conditions, employing single cartridges of emulsion explosive in 45 mm diameter holes. The results, despite wide scatter in the measured values, show the very short duration pressures to range up to 7 MPa and arriving within a few milliseconds after detonation, whereas the much lower amplitude pressures arrive after tens of milliseconds. Both have the potential to seriously affect the performance of an explosives system.

Jan 1, 2005

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By J. M. Wempen

Booster fans, large underground fans, can increase the volumetric efficiency of ventilation systems by helping to balance the pressure and quantity distribution throughout a mine, reducing leakage and reducing the total power requirement. However, in ventilation systems that use booster fans there is a potential for system recirculation, the leakage of return air to intake air, and also for localized recirculation near the fan through the bulkhead and airlock doors. Air that is recirculated locally decreases the system efficiency because the quantity of air flow through the fan increases without increasing the airflow throughout the system. To understand the detailed flow characteristics of a ventilation system with a booster fan, two-dimensional computational fluid dynamics (CFD) models were developed using the software Ansys-FLUENT. Though two-dimensional models do not represent the full complexity of the flow dynamics, they do provide a good representation of the flow characteristics and they allow for a qualitative analysis of how the flow dynamics are affected by the system characteristics. The CFD models were used to evaluate how the number of booster fans, the booster fan placement, the location and geometry of the fan installation and the construction of the airlock system affect the flow characteristics and the localized efficiency of the ventilation system.

Feb 27, 2013

By Edwin Berry

THE consideration of the present value of a mine is of great importance when planning for the operation of a property,, and it is particularly so in the case of mines that have large ore reserves. At various times during the past 15 years, the writer has had occasion to make rather thorough studies of the subject, and has been greatly impressed by certain important points which these studies have brought out, points which, though they may be well known, are often lost track of in the rush to obtain low mining costs and high daily tonnage output. . It is the object of this paper to present briefly, and in a general way, some of these points, and especially those which have to do with the relationship which (1) ore reserves and plant capacity, (2) grade of ore mined, and (3) ore losses in mining, bear to the present value. Present value, sometimes called present worth or actuarial value, means the value today of the future earnings of an enterprise. Great industrial, manu-facturing or railroad enterprises, if properly handled, go on indefinitely and their value is directly dependent on their estimated annual earnings. Mines, or oil properties, on the other hand, have an earning capacity only until the ore or oil is exhausted, and their present value is dependent not only on their annual earnings but also on their life, which is the length of the period over which they can produce at a profit. A mine, or an oil property, is a "wasting asset," while an estab-lished manufacturing business is not, or should not be. In other words, the present value of a mining property. represents a sum of money on which there could be paid from operating profits a determined rate of interest, say 8 per cent., and in addition an amount which, if invested at compound interest as received, would at the end of the life of the mine pay back the present value. In his "Wealth and Income of the American People," Walter Renton Ingalls says: "The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding to the life of the mine."

Jan 7, 1922

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

By James L. Weeks

Introduction This paper attempts to summarize some of the major criticisms of drug testing. Eight problems with drug testing are discussed. These are: • It does not measure something employers have a reasonable need to know, • It is a distortion of priorities, • Drug use is not known to be associated with increased risk of occupational injuries, • Drug testing is proposed as a dangerously simplistic solution to poorly conceived problems, • In the absence of safeguards, it is unacceptably inaccurate, • In the absence of treatment commitments and confidentiality protection for persons dependent on drugs, it is an unethical practice of medicine, • Drug testing is an invasion of privacy, and • It will have a negative effect on treatment of persons with drug or alcohol dependencies. Employers' need to know It does not measure something employers have a reasonable need to know. It is reasonable for employers and fellow workers to want to know if workers are functionally impaired (intoxicated) while on the job. Drug testing does not measure impairment. It measures the concentration of drug metabolities in urine or blood. Unlike measurements of blood alcohol concentration (BAC), drug metabolites are not correlated with impairment or intoxication. They indicate only drug use in the one to two weeks before a urine sample. And, in some instances, they indicate chronic use. Impairment caused by drug use, on the other hand, occurs immediately and declines rapidly within hours. Drug metabolites may linger for days afterwards. Drug metabolite concentrations in urine are a function of (Morgan, 1984; Schartz and Hawks, 1985; MMWR, 1983): • the amount and purity of drug consumed before taking the test, • when the drug was consumed, • whether the person was a chronic user, in which case a certain amount of drug metabolites would be stored in body fat and slowly released, • the person's metabolic rate, and • for metabolites in urine, any dilution effects of urine. Only the first two factors has

Jan 11, 1987

By Rudi Toba

Several areas at the DOZ haulage were observed for the crusher’s location. Initially the new crusher designed position was west of the crusher 1, but due to concerns of the mine crack zone (deep MLZ) the crusher position moved to the south. The new crusher location is situated in a diorite rock massive between 3053 – 3079 levels, with the overall excavation of 2500 cum and dimension of 14m long, 14 m wide and 14 m high. Main Crusher chamber itself excavated by development jumbo in three lifts. Development of access to the bottom crusher was developing the same time as chambering the top crusher. The pocket of the crusher mined with vertical crater retreat system which is initiated in one time after middle slot raise. Collaboration between production and perimeter blast holes to be obtaining in control the actual cuts as per the design shape.

Jan 1, 2007

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By K. Sugawara, H. -S. Jeong, Y. Ishiguro, J. Otani, Y. Obara, A. Hirata

A series of measurements of induced stress by the Compact Conical-ended Borehole Overcoring (CCBO) technique was performed within rock mass around a tunnel excavated in a region that an underground powerhouse is constructed under high initial rock stress. In the measurements, a phenomenon of core disking was observed during overcoring. The selecting method of strain data uninfluenced by the core disking was proposed, using X-ray CT scanner. Then, the state of induced stress determined from the selected strain data was discussed, comparing with the state of initial stress. Eine Serie von Messungen von induzierter Belastung mit kompaktem konisch-beendetem Überbohrverfahren (CCBO) wurde in Felsmassen um einen Tunnel ausgeführt, der in einer Region gebohrt wurde wo ein unterirdisches Kraftwert unter hoher anfänglicher Felsbelastung gebaut wird. Bei den Messungen wurde beim Überbohrverfahren ein Phänomen des Core Disking beobachtet. Die gewählte Methode der Belastungsdaten, unbeeinflusst durch Core Disking wurde vorgeschlagen, unter Verwendung von Röntgen-CT-Scanner. Dann wurde der Zustand der induzierten Belastung aus den gewählten Belastungsdaten diskutiert, unter Vergleich mit der ursprünglichen Belastung. Une série de mesures de contrainte induite effectuée avec la technique de forage de sur-carottage compacte à embout conique a été exécutée dans la masse rocheuse autour d'un tunnel excavé dans une région de construction d'une centrale électrique souterraine sous haute contrainte de roche initiale. Au cours des mesures, un phénomène de discage de carotte a été observé pendant le sur-carottage. La méthode de sélection des données de contrainte non influencée par le discage de carotte a été proposée, en utilisant un scanneur de tomographie calculée aux rayons X. Il s'ensuit que l'état de contrainte induite provoquée et déterminé à partir des données de la contrainte sélectionnées a été traitée, en effectuant une comparaison avec l'état de contrainte initiale.

Jan 1, 2003

By Jack L. Taylor

As expected from similar crystal structures and favorable atomic size factors, titanium, vanadium, and molybdenum are completely soluble in one another above the transformation temperature of titanium. The fl phase parameters of the continuous solid solution are shown graphically. Limiting compositions for retained fl phase have been determined. VANADIUM and molybdenum both have body-centered-cubic structures at all temperatures and, from the atomic diameter comparison factor, 3.9 pct, would be expected to form a complete series of solid solutions. The existence of complete solubility has been confirmed by work' at the Jet Propulsion Laboratory. Furthermore, vanadium and molybdenum have favorable atomic size factors to form complete binary solid solutions with the B phase, high temperature form of titanium, which also has body-centered-cubic structure. Pietro-kowsky and Duwez' and Hansen et al." have established the existence of the complete series of solutions in these binary systems. It would be logical, therefore, to expect that p-titanium, vanadium, and molybdenum would be completely soluble in one

Jan 1, 1957

By R. L. Loofbourow

The adjacent towns of Rouyn and Noranda, centers of the Rouyn mining district of western Quebec, are 360 miles by air line almost duo north of Toronto. Rouyn is reached from the main lines of the Canadian National Railways and the Canadian Pacific Railway at North Bay, Ontario, by the Temiskaming & Northern Ontario Railway and its subsidiary, the Nipissing Central Railway. Noranda is the southwestern terminus of a branch from the Canadian National Railway between Winnipeg and Quebec. The Rouyn mining district is a part of a mineralized zone that has been traced for a distance of 140 miles from Kirkland Lake in Ontario eastward into the Province of Quebec to the Pascalis district. From Rouyn the mine is 5 miler almost duo south over a gravel rend built by the company with assistance from the Province of Quebec.

Jan 1, 1933

Adverse ground behavior events, such as convergence and falls of ground, are some of the most significant challenges and hazards in underground mines. Our goal is to work toward mine-wide, digital, and real-time three-dimensional geotechnical situational awareness and predictive capabilities in complex underground mining operations. This will benefit operators, engineers, and management by enabling them to develop a more proactive approach to ground control. To this end, and inspired by research in the field of remote sensing and autonomous robotics, this paper assesses the potential of mobile light detection and ranging (LiDAR) data acquisition for high-frequency, high-accuracy monitoring tasks in Global Navigation Satellite Systems (GNSS) deprived underground mines. Limitations of current monitoring practices are reviewed. Relevant academic and commercial developments in the fields of indoor mobile mapping systems (MMSs) and simultaneous localization and mapping (SLAM), robust autonomous robotic platforms, and automated remote sensing data processing are highlighted, and their current shortfalls are evaluated. To conclude, the ramifications of this work for the development of future autonomous underground mine monitoring solutions are discussed.

Jul 28, 2020

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

A computerised cataloguing system for geological specimens is described. The catalogue is designed for use with a compactus-type storage system. The information stored in the catalogue for each specimen includes the type of specimen, locality information in terms of standard ~ap sheets and descriptive location, geological age, stratIgraphy, and specimen descriptions. The catalogue can be interrogated at any level of detail on the basis of any combination of these specimen parameters.Other information stored for each specimen 'is the compactus address, collection date, reference information and the type of analyses performed on that specimen:Any mterrogatlon produces a listing of those specimens which satisfy the search criteria.

Jan 1, 1974

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003

By A Cox

It has been demonstrated that all the cadmium from spent batteries, typically 4 g per battery, can be recovered by burning polyvinyl chloride waste to yield hydrogen chloride; this reacts to produce volatile calcium chloride, which can then be condensed and collected in a separate reactor. Alternatively, chlorine may be used to chlorinate the cadmium with equal efficiency. There is also a prospect of using very low concentrations of these gases, less than 1%, to effect the separation. The Cd was recovered more quickly when exposed to sustained, controlled flow rates of chlorinating gases, whereas when PVC was burnt most of the gas was produced in a very short time, not allowing complete reaction. This problem can be overcome by recirculation of the gas into the reactor. The technology is efficient and clean and the equipment used is simple, enhancing the prospects for a pilot-scale version of the process

Jun 21, 1905

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining Co.'s Granite Mountain shaft. How this insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the lire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest pro¬ducer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By Reginald N. Boryor, Steven D. Woods

1.0 Introduction ?Low grade, high tonnage, open pit gold mine. ?Gold bearing Tarkwaian conglomerates. ?Reverse Circulation percussion drilling (25m X 25m grid). ?Composite 1m intervals, logged and split in the field to provide±2Kg samples. ?Samples used to build grade control block models using SURPAC. ?Approximately 100,000-130,000 meters drilled per year. ?RC samples are assayed using Rapid Cyanide Leach (RCL). ?Check assays are done using Fire Assay

Jan 1, 2005