Search Documents

The practice of pumping gases which inhibit combustion for purposes of controlling or extinguishing mine fires is now universally accepted. The practice has been used many times in coal mines in India and the experiences are reviewed. The procedures relating to a membrane based nitrogen generator and to a combustion gases generator are described. The physical properties, practical requirements and economic implications of using different gases is briefly reviewed. Some aspects of the practice as related to mine fires in certain collieries in other countries are dealt with.

Jan 1, 2000

By D T. Froedge

At the 1990 Symposium of the Society of Explosives Engineering, D.T. Froedge, President of GeoSonics Inc., presented a paper entitled "Differential Topographic Vibration Isomapping", which detailed the capabilities of GeoSonics' new Iso-Seismic Service. In this paper Mr. Froedge described how one hundred or &ore free-standing miniature seismographs called Micro-Seis Units, randomly positioned around a blast, could accurately reveal the effects of sub-strata geology on surface ground vibrations. The paper went on to note the "regression analysis of scaled distance versus recorded particle velocity" as being an inadequate predictor of peak particle velocity. This is due to the fact that the calculated "regression analysis" formula for any site is predicted on the wars; case assumption because of a homogeneous and symmetrical sub-strata geology, a condition that rarely, if ever, exists.

Jan 1, 1992

By Muir DM, Ritchie IM, Gibbons SL

Fundamental studies on the transformations of iron oxides have been carried out and related to the solution conditions in the Becher Process. The results show that a number of iron oxide interconversion reactions occur in the aeration reactor with the products depending on the pH, temperature and oxidation potential of the aeration liquor. It is concluded that the lack of process control in the aeration reactor of the Becher Process significantly hinders the ability to predict and produce high quality single phase iron oxides of a consistent colour.

Jan 1, 1989

By S. Tanaka

The Tamano Smelter of Hibi Kyodo Smelting Co. Ltd. was commissioned in 1972. Since start up, the anode production capacity has increased from 101,000 tpy to 290,000 tpy, as a result of the application of continuous improvements at each phase of the expansion projects. The Tamano Smelter had developed several innovations, including the original coke combustion technology for Flash Smelting Furnace operations (T-FSF), and has also been able to extend the operating life of the Peirce-Smith converters. This paper will present several improvements implemented at the Tamano Smelter, and will discuss relevant P-S converter operation.

Jan 1, 2005

By Harold M. Smith

Among the more important raw materials now utilized for the commercial production of synthetic organic chemicals is natural 'gas. Natural gas has been used as a fuel and source of energy almost from its discovery, but its potentialities as a chemical raw material were not realized until recently. Research in the use of natural gas for Chemical synthesis received great impetus from the discovery by Brooks and Humphrey4/ in 1918 of alcohols in the diluted ?acid oil? obtained by sulfuric acid treatment of cracked petroleum distillates. Experimental data soon showed that hydrocarbons from natural gas could be converted to these same products. Laboratory methods for chlorination of natural-gas hydrocarbons, particularly of methane for the production of methyl chloride, methylene chloride, carbon tetrachloride, and chleroform were known before that time but were not developed commercially. Methods for obtaining alcohol by oxidation of hydrocarbons derived from natural gas also were known before 1918 but had not received commercial consideration. Since 1918, and particularly during the past 15 years, the work of chemists and chemical manufacturers throughout the world has resulted in an accumulation of data regarding the reactivity of natural-gas hydrocarbons, and related hydrocarbons found in refinery gases or made synthetically. These data have been used to develop methods for converting hydrocarbons into chemical products and thus form the basis for a large and growing industry.

Jan 1, 1947

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By M. Mikhaylenko

Rhenium, molybdenum and tungsten are the elements demanded by high-end technologies. These metals are found in process solutions in forms of their oxyanions: ReO4-, MoO42- and WO42-. The later two can exist in forms of iso- and/or heteropolyanions. Basically all three metals demonstrate very similar chemical behavior in aqueous solutions. Unfortunately, in their mineral sources these elements commonly accompany each other, like pairs of rhenium-molybdenum or molybdenum-tungsten. Their economical separation is a challenging task.

Jan 1, 2012

By J. M. Toguri, K. Grjotheim

It is known 1,2 that the equilibrium between titanium metal, TiCl2 , and TiCl3, in a solvent of molten metal chlorides, is influenced both by the total amount of dissolved titanium and by the type of solvent. Assuming that the trivalent titanium forms the complex ion Ti111 Cl4, the equilibrium reaction may be expressed by the following equation, (Me) TiIII cl4+ 1/2 Ti = 3/2 TiII cl2+ (Me) Cl The ideal ionic equilibrium constant for this reaction is, Where the N's are the molar ionic fractions in the equilibrium melt, and (Me) the different types of cations present in the equilibrium mixture. The following thermodynamic relation is derived between Kand the concentration of cations in the equilibrium melt, mix The N"S are the equivalent ionic fractions, and so forth are constants corresponding to the standard changes in free energy for reactions in melts where only the cation indicated is present, and f (y1) is a function of the activity coefficients in the equilibrium mixture. When this term vanishes, a simplified linear relationship between In Kideal and the concentration is obtained. The simplified relationship has been applied with satisfactory results to the experimental data of Mellgren and pie,' and Kreye and Kellogg.2 MANY existing methods for the production of light metals involve the reduction of their respective metal halides in the presence of salt melts composed of alkali or alkaline earth chlorides. In such a solution phase, the light-metal halide may undergo stepwise reduction from a higher, to a lower valence, and finally to a zero valent state. In this connection, the disproportionation equilibrium is of great interest. In the case where the higher valence is three and the lower valence is two, the disproportionation equilibrium may be written as follows, 3 Me11 = 2 Me111 + Me [I] If this equilibrium occurs in a salt melt containing a large excess of alkali chlorides, a typical ionic melt is obtained. It is then possible to formulate the cation equilibrium: 2 Me+h' + Me = 3 Me++ [II] Reaction [11] is analogous to a cation exchange reaction. It has been shown thermodynamically that the equilibrium constant for such a reaction in 2

Jan 1, 1960

By E. Hughes, D. Akers, D. Stopek

The Upgraded Coal Interest Group (UCIG), focuses on clean, low-cost options for coal-based power generation via pre-combustion, co-firing and reburn options. Its mission is to preserve and expand the economic use of coal for energy. By reducing the fuel costs and environmental impacts of coal-fired power generation, existing units become more cost effective and thus new units utilizing advanced combustion technologies are more likely to be coal-fired. Two great forces are reshaping the power generation industry, the Clean Air Act Amendment and deregulation of generation. The Clean Air Act Amendment is forcing change by making it necessary for power producers to plan for reducing emissions of sulfur and nitrogen oxides and possibly trace elements. At the same time, deregulation of generation is forcing utilities to focus their attention closely on the short term impact of any change on cost of power. Fuel is a utility's largest cost element; maximum fuel flexibility will be a utility's best weapon in an environment of rapid change. In a regulated environment, a utility was limited in how involved he might get into fuel supply, in a purely deregulated environment he need only be guided by the impact on the bottom line. It is clear that these two forces will promote a close look at factors such as coal upgrading which can have an impact on the availability of low sulfur coal or emission of NOX and trace elements.

Jan 1, 2000

By Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally or times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 1, 1983

By Michelle Mouton, Johanna van Deventer, Jussi Vaarno

Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Impeller rotation speeds of 0-220 rpm were tested, and it seemed that speeds of between 80 and 220 rpm gave similar Fe and Mn removal rates. Co and Cu losses were generally below 1% and 5% respectively at pH 3.

Jan 1, 2007

By Oliver C. Ralston, Dorsey A. Lyon

Volatilization in retorts has been, until recently, the only commercial process of producing spelter, hence the zinc mine operators have had to meet the terms of the zinc smelters in regard to the following requirements: (1) Minimum percentage of zinc the ore must contain; (2) the chemical combination of the zinc in the ore; (3) the proportion present of those elements that interfere with the suceessful recovery of the zinc when the ore is retorted. In consequence of these requirements, only a comparatively small proportion of the zinc ores mined can be shipped directly to the smelters.

Jan 1, 1919

By N. Yamazaki

The supply of clean copper ores, which have high copper concentration and low impurities like arsenic, has declined year by year. Therefore, both mine and smelter sides have to consider how to remove impurities like arsenic. We focus herein on arsenic as an impurity because it is an extremely important issue from the environmental point of view. Approximately 150,000 t of arsenic is input into the copper industry every year. A small part of it is mainly treated in the smelting side. For instance, Ministro Hales Limited, which is a mining corporation in Chile, has performed the calcination process to remove arsenic from ore with high-arsenic content. In the process, flue gas is washed by water, and the final residue is treated by a hydrometallurgical process. Many processes for arsenic removal in various stages have been proposed, and several bottlenecks exist to achieve it. One of the difficulties encountered is getting an assessment of the process, which depends on the countries and/or areas of operation. The standardization of the assessment procedure will be desired in the near future to keep the same environment standards all over the world, and now is the time to start making discussions on this matter. This will be the first step in making an international assessment procedure for arsenic treatment in the copper industry. INTRODUCTION Using the term “sustainable development” without any scientific basis can give people a false sense of security. Engineers and scientists must analyze the total mass flow of energy and materials and estimate local drain on the environment as well as the global impact of a particular industrial activity to ensure sustainability on this planet. The operations of the mining and smelting industries have a strong effect on the environment even if they provide useful materials for human beings. The copper mining and smelting industries have brought about serious environmental problems in the past. For example, the Ashio mine pollution caused big damage to the agricultural sector near the Ashio area in Japan in the late 19th century. One of the most serious problems at that time was SO2 emission because copper ore is sulfide, and the smelting process basically results to sulfur oxidation. The resource balance from a copper smelter in a year, assuming a total production of 16 million tons, can be summarized as follows: discarded minerals, 30 billion tons; sulfur, 16 million tons; iron oxide, 8 million tons; additional smaller amounts of other metals, electricity, and fuel.

Jan 1, 2019

By J Petrolito

"To improve the economic and environmental performance of underground mining operations, it is common practice to return the metallurgical waste material underground as backfill. This is called hydraulic backfill and is used to fill the mined-out areas not exposed to further mining. To provide mechanical support for underground mining a cemented backfill is normally used. Since its introduction, cemented backfill has allowed mining companies to increase their ore extraction and improve working and environmental conditions. However, cemented backfill represents up to 50% to 85% of the mine’s operating cost compared with 5% to 10% for hydraulic backfill.These economic pressures have led mining companies to carry out research into the partial or total replacement of cement using a variety of alternative materials. The materials are generally site-specific materials, readily available, and cost-effective relative to cement. Such investigations have led to reduced cost of many backfill mixes while maintaining, and in some cases improving, the physical properties of cemented backfill. However, in most cases, cement still remains an integral part of any binder combination. This can be attributed to the alternative binders investigated being either non-binding materials or capable of generating only low-strength backfills, except when used in conjunction with cement.This paper provides a historical review of backfilling binder materials and their characteristics. In particular, it reviews the many alternative materials that have been proposed to either partially or fully replace Portland cement as the main binder."

Jan 1, 2005

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

By Ferron A. Olson

Natural bornite (Cu5FeS4) leached in ferric chloride or in sulfuric or hydrochloric acid solutions with oxygen showed several differences. In ferric chloride 80 of the copper was leached in two stages. The first (30 copper removal) requiring one minute was controlled by mixed kinetics (liquid ferric ion diffusion and chemical surface reaction). The second was controlled by formation of a surface sulfur layer and then diffusion through the sulfur. With oxygen in sulfuric acid reaction was slow and only the first stage was studied. Copper removal had an induction period. The bornite structure disappeared at 12% copper removal (also found with ferric chloride) and covellite formed on the surface with a species inside the particles having an x-ray structure similar to CuFeS2 but with composition Cu3FeS4 (also with ferric chloride). Copper removal was controlled by iron dissolution. Surface iron vacancies filled with Cu+ to give CuS while interior copper dissolution produced Cu3FeS4. Preliminary results with oxygen and hydrochloric acid showed 80% copper removal and sulfur as end products (similar to ferric chloride).

Jan 1, 1982

By John E. Kelley

A method for measuring the spark-shower radiance of metals when abraded on a grinding wheel was developed by the Bureau of Mines for evaluating the sparking tendency of metals. The radiance was measured in units of emissive power per solid angle per area of the detector. Over 100 metals were tested and rated relative to commercially pure iron. The metals tested included elemental metals, iron binary and ternary alloys, iron-carbon ternary alloys, commercial steels, nonferrous alloys, and a few hard-metal compounds. Some alloys were synthesized; others were obtained commercially. Alloys that possessed good strength properties were emphasized for selection. The results indicate that the spark-shower radiance of plain carbon steels and carbon alloy steels was greater than that of pure iron. Certain elements, particularly vanadium and chromium, reduced the sparking tendency of iron. Stainless steels and particularly nickel alloys displayed low spark-shower radiance. Some metallic elements had much lower radiance than iron; others, much greater. Plain carbon steels, heat treated to a variety of hardnesses, gave radiance values that generally increased with increasing hardness. The effect on sparking tendency of an increase in hardness of an alloy steel was studied. The sparking tendency increased with an increase in hardness to a maximum, then decreased with a further increase in hardness.

Jan 1, 1974

By Steve Kral

Globalization was the key word for the mining industry during the 1990s, just as productivity was the key word of the 1980s. And globalization will remain the key word as the industry enters the 21st century, according to speakers at the Colorado MPD Meeting held in Colorado Springs, CO in May. The meeting, put on by the Colorado Section SME Minerals Processing Division, drew about 120 people to the Broadmoor Hotel. “Operating Globally” was the theme of the 49th annual conference. Speakers addressed the reasons why mining companies have limited their spending in the United States and have moved into Third World and developing nations.

Jan 1, 1999

By Paul Downing

Identity Theft Outline • What Are MY Chances??? • Types Of Thefts • Sources Of Theft Info • Stolen Identity vs. Background Checks • Information/Data Safeguards • Corporate Data Handling • Reclaiming Your Identity • Monitoring Your Identity

Jan 1, 2006

By C. Dixon

This paper is based on the assumption of some knowledge of the National Water Act. It will consider the question of how that Act fits in with: a) existing laws which overlap on the subject matter b) new laws either in draft or in the process of being compiled c) policies which will eventually find their provisions included in new legislation (e.g. minerals policy) d) international practices. The focus will be specifically on the interaction of legislation relating to water use and water pollution in the mining sector as well as the role of the Department of Water Affairs in mining matters. Hence the title of the presentation.

Jan 1, 1999