Search Documents

By Rolf Katzenbach

Construction of drilled shaft foundations with the use of hydraulic oscillators and rotators to install temporary casing over the full depth of the shaft is described. The equipment and techniques were developed in the 1960?s in Germany and full-depth casing is now the predominant method of construction in Europe. Its use in North America is increasing. This paper presents an overview of full-depth casing methods and a summary of available load test data evaluated by the authors to compare the load transfer and capacity performance of shafts installed by various construction methods. Results demonstrate that load transfer and capacity of full-depth casing shafts are equal to or exceed that of shafts constructed by dry or slurry methods and that measured capacities are consistent with generally accepted design equations. The principal advantage of full-depth casing methods over other installation techniques is that the risk of defects in the shaft is minimized. Casing is able to penetrate into the ground under any geologic or groundwater condition when this technique is applied. Potential delays and cost overruns can thus be avoided and a safe, economical foundation element is created.

Jan 1, 2007

By Harry Asche

The last 12 months has seen the construction of the first Earth Pressure Balance (EPB) TBM excavated tunnel in New Zealand on the Project Hobson sewer storage tunnel for Watercare Services Limited, with the concurrent excavation of the second EPB tunnel on the Rosedale Outfall project for North Shore City Council. Together these tunnels involve a total length of 6km and follow an 8 year pause in TBM activity in Auckland. TBM performance on these two projects is thus of significant interest as there are four major tunneling projects totaling over NZ$8B being planned for Auckland, in similar ground conditions. Auckland?s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20km of the city centre. The paper describes the design and construction challenges for the projects, including TBM performance, ?sticky spoil? management, and risks associated with basalt lava flows and two paleovalleys. Watercare?s Project Hobson also saw the successful implementation of a Geotechnical Baseline Report?one of the first uses of this type of document in Australasia. Rosedale Outfall is designed for high internal water pressures with varying hydraulic flows, with the risk of exfiltration explicitly addressed.

By R. B. Schluter

Drying and preheating (partial induration) the green, unfired iron ore pellets is a means of reducing the energy required to produce metallized pellets. The Bureau of Mines processed three magnetite and two hematite concentrates through the unit operations of pelletizing, preheating in air, and reduction to metal to determine the effects of preheating upon the properties of the metallized pellets. The pellets were prepared in a 16-inch-diameter laboratory balling drum. Preheating and metallization were carried out in an externally heated 4-inch-ID by 4-inch-long stainless steel drum using air for the preheating atmosphere and lignite char as a reductant. The results 'varied considerably: two of the magnetites spalled when preheated in air at temperatures of 900° C and above, and the third magnetite and the hematite flotation concentrate required complete induration at 1,300° C to produce satisfactory pellets. The earthy hematite ore yielded excellent pellets at all preheat temperatures.

Jan 1, 1972

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009

Operations of the new copper smelter at Mount Isa commenced on the 6th February, 1953. Prior to this date a paper by R. V. Anderson (1953) outlined the smelter layout, proposed operation and expected performance.Nominally a 50-ton per day plant, output is currently at the rate of 85 long tons per day. In the first 3t years, of operation to 30th June, 1956, '71,339 tons of blister copper were produced. Operation has been stabilized' and a number of modifications to plant and operation have been made. This paper reviews the progress made to date.GENERAL LAYOUT AND EQUIPMENTThe general layout and equipment follows well-established practice as study of Figs. 1 to 4, and Appendix II will show. This diagrammatic representation of layout (Fig. 1) and flow sheet (Fig. 2) is intended for the purpose of brevity to take the place of a detailed plant description.Choice of site for the smelter was limited by the necessity for close proximity of the waste heat boilers to the powerhouse.Much excavation was necessary before foundation work commenced, but the plant is compact and further expansion is possible.CHARGE MAKE-UPRoaster charge initially comprised concentrates, purchased ores, revert materials, mine sulphide ore and barren sand. As purchased ore receipts increased and as domestic black rock oxidized ore became available, the latter two fluxes were eliminated from the charge. Fluxes at minus i-in. sizing are trucked from crushing plant or stockpile by motor lorries. Filtered mill concentrates are dropped from an overhead conveyor on to the storage patio floor adj acent to the two concentrate bins.

Jan 1, 1957

By Allan E. Martin

As part of a comprehensive investigation of tie mechanism of desufurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, in cooperation with the Institute of Technology-, University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope. Vogt5/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and bins, or isomorphous compounds, such as (FexCay)S and (MnxCy)S, were precipitated Prom the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.

Jan 1, 1941

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which 'complete the cycle' of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987

By D. P. Tripathy

A supply chain encompasses all the activities associated with the flow and transformation of goods from the raw materials stage(extraction), through to the end user. Supply chain management (SCM) is the integration of these activities through improved supply chain relationship, to achieve a sustainable competitive advantage and it rests on its ability to provide the right goods and services when and where needed. The supply chain is the vital component of any company?s value chain which links the operating processes to its supplier and customer. The globalization of business promises to offer new and unique challenges for the supply chain competencies of most firms. Challenges will also increase in the environmental aspects of supply chain often referred to as ?Green Issues?. The supply chain of mining industry comprises of the flow of material and information from the mine site, to processing and loading for transport, to the customer. However, due to recent changing environmental requirements affecting mining and mineral processing operations, increasing attention is given to developing environmental management (EM) strategies for the mineral supply chain. This paper focuses on: ? Environmental factors leading to the development of an extended environmental supply chain, ? Additional challenges presented by the extension, ? Performance measures appropriate for the extended supply chain, ? Developing a general procedure towards achieving and maintaining the green supply chain.

May 1, 2006

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

A comprehensive review of ore pass records, from ten Quebec underground mines, indicated some of the limitations of available design tools to predict the occurrence of ore pass interlocking hang-ups in metal mines. The Distinct Element Method was used to perform a series of numerical experiments in order to investigate the influence of ore pass geometry, rock fragments shape and size distribution on material flow in an ore pass. Guidelines have been developed to help limit the occurrence of interlocking hang-ups in an ore pass. The proposed guidelines were evaluated with respect to field observations. Ein kompletter Bericht der Erzrollezeichnungen, von 10 Quebec unterirdischen Gruben, hat einige der Beschränkungen der vorhandenen Designwerkzeuge angezeigt, um das Auftreten Erzrolle der blockierenhang-ups in den Metallgruben genau vorauszusagen. Eine Reihe numerische Experimente mit der eindeutigen Element-Methode, wurden aufgenommen, um den Einfluss von Erzrollegeometrie, Partikelform nachzuforschen und Felsenkorngrößenverteilungen auf Materialfluss in ein Erz überschreiten. Dieses hat zu die Entwicklung der Richtlinien geführt deren Implementierung das Auftreten der blockierenhang-ups in eine Erzrolle begrenzen sollte. Die vorgeschlagenen Richtlinien wurden in Bezug auf Labor- und Feldbeobachtungen ausgewertet. Une revue de la performance actuelle des cheminées à minerai dans 10 mines souterraines du Québec a indiqué les limites des outils de conception servant à dimensionner les cheminées pour minimiser le nombre d’accrochages par enchevêtrement rocheux. Des séries de modélisations numériques, utilisant la méthode des éléments distincts, ont été réalisées afin d’évaluer l’influence de la géométrie des cheminées, de la forme des fragments rocheux et de la distribution granulométrique sur l’écoulement du matériel dans les cheminées. Cet exercice a permis de développer des lignes directrices pour le dimensionnement des cheminées afin de limiter l’occurrence d’accrochage par enchevêtrement rocheux. Les lignes directrices proposées ont été évaluées en fonction des observations effectuées sur le terrain.

Jan 1, 2003

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By C J. N Wilson

The central Taupo Volcanic Zone is a region of intense Quaternary silicic volcanism accompanying rapid crustal extension. Modem central TVZ is the most frequently active and productive silicic volcanic system on Earth, erupting rhyolite at c.0.28 m3 s-1. The rhyolites show no major compositional changes with time, but the total extent of magma chamber zonation has changed with the advent of rifting and crustal extension at c.0.7 Ma. At least 34 caldera-forming ignimbrite eruptions have formed a complex sequence of relatively short-lived, nested and/or overlapping volcanic centres in central TVZ. Taupo contrasts with other large silicic magmatic systems in the exceptionally high frequency, but small size, of caldera forming eruptions. This contrast reflects the thin, rifted nature of the TVZ crust that precludes the development of long term magmatic cycles at Taupo. Within central TVZ, non-rhyolitic compositions have been erupted apparently irregularly in time and space; in particular there is no evidence for a geographic separation of basalts from andesites. TVZ is a rifted arc, but its segmented nature, high thermal flux and voluminous rhyolitic volcanism make it unique on Earth.

Jan 1, 1995

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

As part of the Bureau of Mines program to reduce U.S. reliance on foreign suppliers of strategic and critical metals, research was conducted to improve technology for the recovery of critical metals from hardface alloy grinding waste, a form of superalloy scrap. This report describes a hydrometallurgical process that demonstrated on a laboratory scale that 79 pct of the chromium, 97 pct of the cobalt, 99 pct of the manganese, 99 pct of the nickel, and 90 pct of the tungsten could be recovered in chemical form from hardface alloy grinding waste. The process involved deoiling the grinding waste, followed by chloride-based dissolution of the deoiled material. A high-grade calcium tungstate (CaW04) product was recovered from the resultant leach residue by caustic leaching and precipitation. Iron, cobalt, man-ganese, and nickel chlorides were sequentially recovered from the leach liquor by solvent extraction. Amine extractants were used to extract the iron, cobalt, and manganese; decanal oxime was used to extract the nickel. Market-grade cobalt chloride (CoCI2), manganese chloride (MnC12), and nickel chloride (NiCl2) products could be produced directly from the resultant strip liquors. The final raffrnate was a relatively pure chromic chloride (CrCI3) solution that compared favorably with commercial solutions.

Jan 1, 1988

Sandsloot open pit is situated on the northern limb of the Bushveld Complex, 250 km north east of Johannesburg, South Africa. Sandsloot is currently the largest open pit platinum mine in the world and is one of six potential open pits in the area. The geotechnical strength properties of the Platreef have posed significant mining and processing challenges to the PPRust operation since inception in 1992. In order to optimize the whole business as opposed to isolated cost centres a mine to mill initiative was embarked upon in 1997. Initial work focused on ore characterization and an entire suite of data was collected for each rock type. This included mineralogy, geochemistry, geotechnical, blast ability indices, as well as metallurgical strength data. The second phase involved the clear definition of customer requirements, namely the optimum performance criteria for the plant and mining departments. This involved extensive field trials and data capture to measure the interaction and influence of the mine to mill value chain. Once the design targets were defined, a 3D geotechnical model was constructed to ensure that the targets were consistently achieved. The model is very similar to an ore reserve model; however, it is populated with geotechnical, metallurgical and blast index data. Through software queries the appropriate blast powder factor for each mining block can be obtained, thereby ensuring the correct fragmentation is blasted for the plant and mining operation. The initiative has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. Additionally, the initiative has benefited both brownfield and greenfield projects on the PPRust operation

Jan 1, 2006

By Paul S. Goodman

Volume I This report presents the first national survey of miners&apos; attitudes and opinions about their-work. The goal is to present attitudinal data that bears on coal production. Interviews were conducted in 26 mines with 2,000 miners. High levels of cooperation were exhibited by management, union and the employees. Data are presented about miners&apos; attitudes about general aspects of their work such as pay, supervision, their jobs, etc. Another section of this report reviews opinions about specific aspects of work performance. Recommendations are presented.

Jan 1, 1985

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By I. Gombköto, J. Bohm

"In Europe, and therefore in Hungary opening a new mine is harder and harder. Depletion of mines, unfavourable legal and economic changes, and growing public concerns are the main reasons. Social and economic interests require total utilization of mineral raw materials of the operating mines, and furthermore utilization of waste heaps of the former mines. There are 5-6000 waste heaps of the operating and the closed mines in Hungary. 2000 of these waste heaps have already been estimated, and researches show that total amount of waste heaps can be calculated to 1 billion tones. These researches left out of consideration waste heaps exploited and placed in deep lignite mining. In several projects and researches we analysed processing of waste heap and possibilities to use its components. A processing technology for utilizing waste heaps has been developed based on laboratory and pilot plant tests. Great amount of useful materials of quarrying waste heaps can be utilized with this technology. Tests were also done for processing waste heap of a former ferrous metals mining. The developed processing technology contributes to use these waste heaps as aggregate for cement industry, as dielectric and aggregate for construction. The essay presents in details main characteristics of waste heaps, technologies already used for processing waste heaps of quarrying and ferrous metals mining, mass balances and qualitative parameters of the end products."

Jan 1, 2011

By H Zimba, S Sondashi, M Chitambo

By the time a reagent is finally accepted by a mine for use on its plant it could have gone through several screening and evaluation stages. These stages may include laboratory and plant evaluation testwork. This paper outlines the steps that were followed to select, design and implement a frother for KONKOLA COPPER MINES PLC Nchanga Copper Concentrator in Zambia. It discusses initial frother screening work conducted at the Betachem metallurgical laboratory and the subsequent laboratory screening testwork conducted at Nchanga Concentrator. A modified Bikerman test method is discussed which was used to design a frother for the Nchanga flotation plant. The paper also gives an account of several plant scale trials conducted on Nchanga flotation plant and discusses the plant results, frother consumption patterns and some commercial concerns, before the product was finally accepted by the mine.

Jan 1, 2007

By T. Lindstad, V. Myrvågnes

In the production of high silicon alloys, carbonaceous materials like coal, coke, charcoal and woodchips are utilized as reducing agents. Primarily based on historical prices of charcoal compared to fossil reduction materials, the Norwegian Ferroalloy Industry has mostly been using coal and coke (char) as carbon source. The most important role of the carbonaceous material is to react with the SiO gas to produce SiC. The ability of the reduction materials to bind SiO gas can be measured and the value is recognised as the reactivity of the carbon source. This reactivity is one of the most important parameters in the smelting process in order to obtain a high yield of metal. The reactivity of the carbon materials is directly correlated to the material properties. It is known that the rank of the coal influences the SiO reactivity where low rank is beneficial. Coals of the same rank have however proven to have varying reactivity. In order to investigate how the micro-constituents of coal influence the reactivity towards SiO gas, three single seam unwashed coals of different origin which fulfil the requirements of the Norwegian Ferroalloy producers have been chosen. As the structure in the carbonized product is a function of petrographic constitution and carbonization parameters, the coals have been separated into different density fractions. The various density fractions of the same coals proved to have significantly different petrographic composition. The coals were carbonized according to a procedure simulating the conditions the coals experience when charged to an industrial furnace. Chemical-, physical- and petrographical properties of both the coals and the resultant chars have been thoroughly examined and correlated towards the SiO reactivity.

Jan 1, 2007