Search Documents

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By Colin Curtis

In recent years, Manchester Airport has undergone expansion including the construction of a second runway, a new terminal building (Terminal 3) and extensions to the existing Terminal 1. Manchester is Britains third largest airport and ranked 20th in the world for international traffic. Arup (Manchester) was engaged as consulting engineer in a multi-disciplinary role for the terminal works. Part of this was a geotechnical commission including site investigation and pile design followed by supervision. This paper reviews the piling for the old, new and terminal extensions. In total, five pile types have been utilised over the years. The original 1950's Terminal 1 was founded on driven cast in situ piles, with a later 1970's extension utilising rotary augured piles. The recent piling comprised continuous flight auger piles (CFA), driven steel tube and tripod bored; the latter in areas of restricted access or low headroom. The ground conditions are Made Ground over thin Alluvial and Glacial drift, in turn, over a generally weak to moderately weak gypsiferous mudstone. All the piles were socketed into the mudstone. In terms of the new CFA piles, quality control using the instrumentation monitoring was problematical, but a substantial static load and integrity test programme resolved pile performance. Part of the work is matching new pile performance with previously installed piles and the continued use of older piles with new loads. Research provided some data on the older piles, including some static load test data, which enabled back analyses of their design and likely behaviour. Differences in design methods, installation techniques and pile behaviour based on load tests will be discussed.

Jan 1, 2001

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Ertugrul Kaya, Kagan Ozdemir

The results of bench blasting on quarries, have important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc., and the total costs of that mine. Drilling and blasting is an important step in mine producing chain and its results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. Within the scope of this study, the three different hydraulic excavators’ working performances have been studied considering the particle size distribution after bench lasting at a quarry in Istanbul Turkey. Five shots have been realized on the quarry and average particle size of muckpile after each shot were assessed by digital image analysis method. Bucket loading times have been measured by stopwatch study after five shots. Excavator bucket loading times were also estimated by bucket loading time estimation formula which was published in ISEE 2007 Conference, Ozdemir et al. 2007. Estimated and measured times have been statistically analyzed and the accuracy rate of formula has been determined for five events.

Jan 1, 2008

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By Andrew K. C. Wong

Hydraulic transport has been considered as one of the most economical methods in transferring granular materials over relatively long distances. In the natural world, it is used to transport basic material required for the support of life; in industry, it is a method widely adopted for handling materials. But the phenomena of hydraulic transport has not yet been thoroughly understood. As most of them are conditioned by a number of hydraulic and mechanical parameters, of which the basic relationships are not fully known, the traditional approach in relating these parameters to the energy requirement is purely empirical in nature. Empirical formulas, such as that proposed by Durand, (1) only give satisfactory results over a selected range of (particle size)/(pipe diameter) ratios and slurry concentration. When the case is more complicated or when new situations arise, the empirical formulas fail to give good predictory results. In fact, most of these formulas are based upon dimensional analysis, where the underlying physical interaction is not explicitly considered. Apart from the loosely related, non-dimensional groups incorporated in the formulas, there is practically no analytical means for modifying the formula so as to enable it to cope with more complex real physical situations. Although it seems quite remote that a complete rigorous solution to this highly complex problem could be generated in the near future, it is generally recognized (2, 3) that research in this area should be directed to more comprehensive studies of the obscure phenomena. In fact, there are a good number of very basic problems such as the effects of gradation and concentration of particles upon

Jan 1, 1972

By Ry Stone

To maintain longwall continuity, NRE Wongawilli Colliery extracted the approximately 20-year-old Thompson Mains and in doing so, 20 roadways were holed into during longwall retreat. The orientation of these roadways with regard to the longwall face varied between (i) a parallel alignment where the entire roadway was simultaneously subjected to a significant increase in vertical stress on holing and (ii) a more favorable high angle of alignment, meaning that only a portion of the roadway was subjected to an increase in vertical stress on holing. In addition, the longwall holed into and was recovered in one of the existing roadways. The geotechnical environment presented several additional challenges during longwall retreat. The orientation of the stress field resulted in a major horizontal stress notch on the maingate and an elevation in the major horizontal stress in front of the longwall face during the retreat up to an adjacent goaf edge. The presence of geological structure zones also resulted in both swings in the major horizontal stress direction and increased levels of roof deformation. The gate road support designs were based on commonly accepted strata management techniques and principles. The support designs in the hole-through roadways were based on empirical design models generated from (i) aconceptual geomechanical model of pre-driven hole-throughand recovery roads and (ii) a worldwide database on pre-driven hole-throughand recovery roads. Imperative to the success of extracting the panel was a sitespecific strata management process. In this regard, consideration was given to the following: roof displacement monitoring in the gate roads (in particular, Longwall (LW) Acceleration Position), roof-to-floor convergence monitoring in the hole-through roadways, the ability of the mine to limit downtime prior to and during holing by utilizing an Authority to Mine (ATM) type process, and the use of Trigger Action Response Plans (TARP).

Jan 1, 2012

By S. Hardy

The paper describes state of the art non-linear analyses of the pile groups that were employed during the raising of the 133m high triumphal arch which forms the centre piece of the new Wembley stadium in North London. The deformation behaviour of these piles groups was critical during the lifting process, due to the slendemess of the arch structure. The issue was made more critical by the high profile nature of the project. The results of Class A (Lambe (1973)) predictions of the pile group movements are compared with observed displacements and rotations which were accurately measured on site. To illustrate the importance of soil non-linearity on pile group behaviour, comparison is also made with pile group analyses which assume a linear soil stiffness.

Jan 1, 2006

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

Building the Unified Comminution Model The Unified Comminution Model (UCM) was formulated with the vision of bringing all comminution models onto a common base. The structure of the model relies on knowledge of the mechanical environment in the comminution devices to predict the modes and rates of collision in a device. A detailed understanding of the breakage modes and an ability to correctly test these modes for the ores in question is then required to feed into the UCM. A model structure has been developed that has the capability of dealing with multiple modes of breakage, such as low energy impact surface damage, chipping, sliding abrasion, cumulative impact body breakage and the transition of rock between modes. A critical review is presented on the shortcomings and limitations of utilising the discrete element method (DEM) to provide the mechanical environments. The assumptions and applicability of utilising DEM in milling models are presented and proposed routes to building a realistic mechanistic model are proposed. Based on this more realistic measures of collision energy have been derived from the DEM simulations, which better mimic the real breakage tests. Generic forms of the collision energy distributions have been observed and developed into functional forms for use in the simulation environment. The method of application of this model to a pilot SAG mill is presented.

Sep 13, 2010

The project to reopen the Tasmania Mine has centred around efforts to reopen the Hart Shaft to access the high grade reef remaining below the old workings, which extend down to 457 in. Efforts in 1982 and 1987 were frustrated by unstable clay ground around the shaft, which resulted in significant subsidence of the shaft collar and lining. A successful program has since been implemented to solve the problems, stabilize the collar and recover the upper shaft which had collapsed down to 90 m.

Jan 1, 1989

By C E. Vidal

Geological exploration and mining development increased their intensity and rate of success during the last five years in Peru. Particularly relevant are the mining projects of Yanacocha and Pierina for epithermal Au and Ag. Also relevant are the new mining operations at Iscaycruz and Uchucchacua for limestone replacement Zn- or Ag-rich base metal skarn deposits. Miocene continental volcanics host the low-grade but near-surface orebodies of the Yanacocha mining district in Cajamarca. Several deposits have been mined since 1994 with open-pit and heap-leach gold production increasing from 300 000 ounces to 1 300 000 ounces in 1998. In a similar geological setting, but with three times the grade of Yanacocha, the Pierina valley-leach operation in Ancash is set to produce 800 000 ounces Au during 1999. At Iscaycruz in Lima, Cretaceous limestones host massive pyrite and sphalerite skarn deposits with 10 to 20 per cent Zn. Mining and milling were started in 1996 with last yearÆs production rising to 180 000 tonnes of Zn concentrates. At Uchucchacua, selective underground mining of fracture-controlled Ag skarns, with 400 to 420 g/t, has been recently increased from 1200 to 2000 tonnes per day to produce 5.5 million ounces Ag during 1998. Advanced exploration projects are located in the framework of nine Phanerozoic metallogenic provinces. Mineral deposits of preferred attention are precious metal disseminations and veins, base metal replacements and skarns, porphyry Cu (Mo-Au), Mississippi-Valley-type Zn and base metal volcanogenic massive sulphide deposits. Geological discovery of new orebodies enables a sustainable development of the mining industry in the country.

Jan 1, 1999

By Frank G. Horino

This report presents a method of utilizing the Coulomb strength criteria for estimating the strength and stability of pillars and pit slopes containing planes of weakness. It is assumed that the Coulomb theory, as a special case of the Mohr envelope, is a satisfactory first approximation of failure in uniaxial compression or triaxial loading with low lateral loads. Accepting this assumption for brittle materials, an expression for the strength decrease of rock pillars containing a plane of weakness or fracture at any angle of orientation is derived. As few as six samples (three solid cores and three fractured cores at a failure-oriented angle) are required for testing uniaxially and triaxially to statistically determine the coefficients of friction and the shear strengths of both the solid rock and the fracture plane and the range of failure angles of the fracture plane. Interpretation of the data shows that the mean normal stress and maximum shear stress technique of analyzing the data is superior for solid core and that shear and normal stress values using angles of failure should be used for fractured specimens with failure-oriented angles. Plots of either the strength or strength ratios against fracture angles obtained from oriented drill core samples give a useful first approximation of strength decrease due to fracture. Using the same test conditions for both fractured and unfractured material increases the validity of the tests.

Jan 1, 1970

By Richard Havens

Acidic and basic uranium leach plant residues located on the Navajo Indian Reservation, Tuba City, Ariz., were successfully stabilized against wind erosion using a relatively low-cost chemical method. An elastomeric polymer chemical was applied to the dike areas and a calcium magnesium lignosulfonate to the beach areas of three tailings ponds. The water-soluble chemicals were applied with an automated sprinkling system. The stabilization cost was $335 per acre for the 34.5-acre tract.

Jan 1, 1969

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By Oliver Bowles

In 1943 the Bureau of Mines began a review of trends in consumption and prices of the more important nonmetallic minerals. The first report covering building materials4/ appeared in December of that year. The present paper, which deals with chemical raw materials and fertilizers, is the second of the series. The 34 years from 1910 to 1943, for which statistics are presented herein, comprise periods of uneventful peace, unparalleled prosperity, industrial depression almost to the point of stagnation, and two wars of world proportions.

Jan 1, 1945

By E. Chin

The domination of Bangladesh's mineral industry by natural gas was in for some possibly significant changes. A modest flow of crude oil was struck in a gas development well in the northeastern corner of the country. This was the first commercial flow of crude oil in Bangladesh. All crude oil was being imported, which cost a significant proportion of the nation's foreign exchange earnings. The development of an oilfield producing only a few thousand barrels per day would be a welcome help to the economy. Additional exploration at a 1985 coal discovery in the northwest indicated a considerable reserve of good-quality coal at a depth suitable for mining. If the coal is mined, it would be a boon to the local economy because natural gas was not available in the area.

Jan 1, 1988

By Philip A. Dirige

This paper presents the variability of responses of paste backfill specimens that have been prepared with varying binding agent and binder combinations, when subjected to uniaxial compressive strength testing. A testing program conducted for an underground operating mine to produce cost efficient paste fill recipes using four different binding agents, in various ratios and combinations, is presented to illustrate the responses. These binding agents are Normal Portland Cement Type-10 (NPC T-10), oxidation or sulphide attack resistant binder (Binder A), replacement binder B (Binder B), and replacement binder C (Binder C). The paste fill recipes were prepared at 2, 3.5 and 5% binder content at varying binder combinations, at fixed size and tested in a Material Testing System (MTS) under constant strain rate conditions following cure times of 7, 14, 28, 56, 90, 112, 180 and 240 days. The results of tests suggested that the strength data clearly shows a trend of increasing strength with increasing binder content but not necessarily cure time. It is noted that all the blends achieved dramatic increases in strength up to 28 days of cure and then either increased or decreased moderately beyond 28 days curing, depending on the binder content and binder combination. The moderate decrease is apparent for the 2% paste fill blends and in some binder combinations of the 3.5 and 5% blends, which indicated lackluster performance beyond 28 days curing. This lackluster strength performance indicated that the binder content and combination may not be sufficient for the paste fill to achieve complete hydration and acquire adequate strength performance beyond 28 days. This study indicated that economic paste fill recipes can be designed with confidence using affordable alternative binders. However, it is noted that these alternate binders cannot be used as stand alone binders but should be used in combination with NPC to facilitate hydration of the paste fill.

May 1, 2006

Attractive geology does not guarantee mining investment if a region’s policies are bad, according to mining executives surveyed in the Fraser Institute’s seventh Annual Survey of Mining Companies. Companies responsible for a combined US$642.4 million in international exploration (during 2002) rated the policy attractiveness and mineral attractiveness of mining jurisdictions around the world. Jurisdictions like Chile, Australia, Quebec and Nevada bolster their attractive geology with mining-friendly policies, the report said. These locations do well on the overall investment attractiveness index. On the other hand, jurisdictions like British Columbia and Indonesia, each with excellent geology, are hurt by their policies, which have lowered their score.

Jan 1, 2004

By H. Walqui, G. Rajala, G. Suardini

The Empire mine began operations on 1963. Low grade Magnetite ore is processed to produce iron pellets for blast furnace feed. Three expansions were added to the original plant and several equipment upgrades have been completed to improve the plant performance as the ore characteristics have been changing through the life of the mine. Size reduction is carried out by two grinding stages, the first one using autogenous grinding and the second one using pebble mills. Pebble crushing is also used to break the critical size fraction and increases primary grinding capacity. This paper describes changes in the configuration of the grinding circuits that have helped increase plant throughput and reduce power consumption by more efficiently utilizing assets available. Understanding the different components of the size reduction circuits and plant sections has allowed shifting part of the load from one section of the plant to another without affecting plant throughput.

Jan 1, 2007

By L. A. Ruth

Vision 21 is a government/industry/academia cost-shared partnership to develop the technology basis for integrated energy plants that will, early in the 21stcentury, result in the deployment of ultra-clean plants that produce electricity and “opportunity” products. Vision 21 plants will use fossil fuel feed-stocks in combination with other domestic resources, e.g., biomass, municipal waste, and petroleum coke. Opportunity products could include transportation fuels, steam, high-value chemicals, synthesis gas, and hydrogen. Performance targets for Vision 21 plants, example plant configurations, and the key technologies that will be needed are described.

Jan 1, 2000