Search Documents

Impala Platinum?s No.16 Shaft mine is currently under construction and is expected to reach full production of 256 500 tons per month by 2014. Mining will start at 1 260 m below surface with a maximum mining depth of 1 535 m where virgin rock temperatures of 56.6°C will be experienced. As a result of depth, high virgin rock temperature and narrow reef mining, an expected total of 31.5 MW[R] of air cooling capacity will be required to achieve acceptable underground conditions. This will be achieved by cooling mine intake air in a single dedicated air cooling installation located on surface. The compact installation includes air cooling spray chamber, refrigeration machines, condenser cooling towers, evaporator and condenser water reticulation as well as all electrical and control systems. Construction and commissioning of the first phase of this air cooling installation has recently been completed on a turn-key contract basis.

Jan 1, 2009

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By G. W. Jones

In a previous report,6 results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.l cubic feet when the number of ventilation openings in the cover was varied. from no openings to a maximum of 48. The results showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

By P K. Smith, N G. Corner, R J. Ryan, D C. Arne, F P. Bierlein

The Reefton Goldfield has produced 67 t of gold from mesothermal vein gold deposits in metasedimentary rocks of the Greenland Group (Cambrian-Ordovician). The Globe-Progress deposit contributed 13.2 t (418,000 oz) of this total, predominantly from quartz veins. Recently a resource of 14 Mt at 1.96 g/t Au (27.5 t or 882,300 oz of contained gold) has been delineated at Globe-Progress in quartz vein remnants and disseminated within adjacent sedimentary rock, much of which has been locally brecciated. The breccias consist of quartz vein and sedimentary wall rock fragments set in a matrix of clay ærock flourÆ and sulphide (arsenopyrite plus minor pyrite and stibnite). Gold, closely associated with sulphide, is disseminated within the breccia. Disseminated gold also occurs in massive siltstone and sandstone adjacent to the quartz veins and breccias. Exploration drilling at Globe-Pogress, and several other Reefton prospects (e.g. Capleston, Merrijigs, Big River and Alexander River), has intersected zones of disseminated arsenopyrite carrying up to 20 g/t more gold. These mineralised sediments commonly have little or no megascopic quartz and or carbonate veining. There is little visible indication of former primary or secondary permeability for the passage of hydrothermal fluid and deposition of gold. However, porosity and permeability were formerly present in inter-granular pore spaces and microveinlets now filled with quartz, carbonate and K-mica. The Fosterville gold deposit in Victoria bears many similarities to the Globe-Progress deposit at Reefton, in terms of age, host rocks, hydrothermal alteration and mineralisation style. Many ofthe disseminated deposits in Nova Scotia, including deposits at North Brookfield and Moose River (Touquoy Zone), have similar characteristics to the Reefton disseminated mineralisation, but commonly have abundant pyrrhotite and some deposits have disseminated metal alloy grains of complex metallurgy.

Jan 1, 2000

By Andrew B. Cecala

The Bureau of Mines conducted a brief laboratory study on the 10-mm diam Dorr-Oliver nylon cyclone to investigate (1) whether high wind speed (>300 ft/min), or sampler inlet orientation with respect to wind direction, can introduce errors when sampling respirable dust, and (2) whether any such errors can be reduced by using an inlet shield. Being preliminary in nature, the study was not structured to produce definitive results, but rather to discern likely trends and to indicate whether or not a more in-depth study of the problem is warranted. Photometric mass sensing measurements suggested that as the wind velocity increased, the cyclone sampling directly into the high-velocity airstream tended to oversample, relative to the cyclone sampling in a low-velocity airstream. Orientation of the sampler introduced measurable differences in sampling efficiency at higher wind velocities. A shield placed around the cyclone diminished the effects of wind velocity and sampler orientation on sampler performance. Results of this work offer sufficient evidence to substantiate the need for a more in-depth study.

Jan 1, 1983

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By Leslie S. Rubin

A ventilated helical boost pump was developed that can handle varying flow rates and/or solids concentrations while operating at a single rotational speed and without computer assisted feedback controls. The boost pump developed and briefly tested during this program was designed to accomodate flows suitable for a 3-in. diameter pipeline. The boost pump's ventilated design provides the automatic pressure regulation needed to meet the system's requirements for supporting transient pipeline flow.

Jan 1, 1984

By John H. Soulé

This paper describes the location and general features of the ?Red Bed? or sandstone copper deposits in southeastern Colorado and New Mexico. Most of the areas containing this type of deposit were visited, and many deposits were examined. Some deposits were not visited because of lack of information as to their location. In the large area covered a great variety of climatic, geographic, and topographic conditions exists. Some of the deposits are in arid areas, whereas others are in heavily forested regions. Altitudes range from 3,400 to 9,200 feet, and the terrain varies from flat plains to rugged mountains. Transportation is a difficult problem in most of the districts, involving long truck hauls to a railroad and long rail hauls to a smelter.

Jan 1, 1956

By J. Kazakoff

"The success of gold recovery at the Jolu gold mill depends on many variables. The most important ones are the people, the ore body, plant design parameters, equipment selection and cost control. This paper will briefly hiqhlight the above, the main focus, however will be on the gravity gold circuit.The gravity circuit requires judicious operator attention in order to operate properly. In return the circuit gives immediate visual results for mill peopleIntroductionThe development of the Jolu property to the production stage was carried out quickly, efficiently and economically. The property became a gold producer ahead of schedule and under budget.The Jolu property is a joint venture between International Mahogany Corp., a 70% partner, and Corona Corporation, a 30% partner. Corona Corporation operates the Jolu Gold Mine, located 140 kilometers north of LaRonge and 520 kilometers north of Saskatoon."

Jan 1, 1990

By G. H. Hope

"Pamour Porcupine Mines of Timmins, Ontario operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the area. The area milling concept was adopted by Pamour in 1971 and has been used successfully since then. The purpose of this paper is to discuss the advantages and the problems of area milling. Pamour Porcupine Mines Limited operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the Porcupine region. The area milling concept was adopted as the route to survival for Pamour and has worked successfully. HISTORICAL BACKGROUNDProduction of gold from the Porcupine region in Northern Ontario started in the early 1900's and has been continuous since that time. Some of the major operators were companies such as Mcintyre, Hollinger, Dome, Pamour, Paymaster and the list goes on. An underground survey would reveal hundreds of miles of drifts and raises. The main group of mines extends from South East of Timmins to the Pamour Mine, 15 miles to the east. During the lean years of the sixties when gold prices were low, labour costs were rising rapidly, and ore grades were dropping, many of the area mines closed down their operations."

Jan 1, 1981

On April 1, 1982, the Bureau of Mines and the Department of Energy entered into an Interagency Agreement to develop an enhanced computer cost model for uranium in situ leach mining. The original computer cost model contained data base information related to two regions; the Wyoming basin region and the South Texas trend area. The enhanced cost model contains additional information on San Juan Basin type deposits. This addition is significant because it expands the model's capabilites to include one of the largest uranium producing areas in the United States and developes costs related to uranium production from in situ leach mining. The data base was expanded and modified to include changes necessary for San Juan basin type deposits. These changes included, but were not limited to, state and local taxes, royalty payments, depth of deposits, drilling costs, and electrical costs. Also site visits were taken to verify many of the base case parameters. Consequently, the data base has been incorporated into the computer program and existing software was modified to provide for the additional data. Information was obtained on drilling coats and therefore the current program more accurately reflects these costs to depths of 2500 feet. This depth parameter has been expanded to include Wyoming Basin and South Texas scenarios also. Verbal communications were held with one operator in the Crownpoint, New Mexico area as well as the state regulatory agencies to help validate the expanded model. As a result of these changes, several tables have been included, summarizing changes in the new default parameters and the overall range of input parameters.

Jan 1, 1982

Industrial minerals and rocks are those which are economically important because of desirable physical and/or chemical properties rather than metal or energy content. The evaluation of these resources for investment purposes in general follows established procedures after due consideration of well documented input data. However, in view of the sensitivity of many industrial mineral projects to specific inputs they require very careful analysis. The characteristics of the industrial minerals and the industrial minerals industry are reviewed and the significance of logistics, customer requirements, technology and marketing are discussed. Implications in relation to resources/reserves terminology are considered with phosphate rock used as an example. It is concluded that industrial mineral projects as a consequence of technology and market dependence in particular can give a high level of investment risk. The industry, however, offers most interesting and challenging employment opportunities for geologists, mineral engineers and economists.

Jan 1, 1988

The mineralogy of the platinum group metals is fairly complex, and it is therefore not surprising that the different minerals have variable responses to metallurgical processes, in particular, flotation and leaching. The PLATSOL® leach process was developed to extract simultaneously base metals, gold and platinum group metals from various materials. Extensive research has indicated that most PGM?s were amenable to the PLATSOL process, with the notable exception of cooperite PtS. Further work showed that a thermal pretreatment at 500-700ºC transformed the structure of the cooperite and similar refractory minerals (Pt,Pd)S into Pt metal and Pt-Pd alloys that responded well to the PLATSOL® process. Examples are presented of the mineralogy of PGM concentrates as produced, in the residue from the PLATSOL® leach and after thermal pretreatment.

Jan 1, 2006

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located above the Arctic Circle in northern Sweden, is the second-largest underground mine in the world today. The orebody is a world-class high-grade magnetite deposit, from which three raw ore products are extracted. We use mixed integer programming to determine a production schedule, i.e., which production blocks to mine, and when to start mining them, so as to minimize deviation from planned production quantities while adhering to the operational constraints of the mine. The resulting model contains thousands of binary variables and a commensurate number of constraints, precluding us from obtaining a schedule in a reasonable amount of time. We describe a method that builds on prior, related work, to expedite solution time. Keywords: underground mining, production planning, optimization, integer programming

Jan 1, 2003

Development of New Comminution Testing Methodologies for Geometallurgical Mapping of Ore Hardness and Throughput The emerging discipline of 'geometallurgy' is becoming increasingly recognised as a discrete and high-value activity that reflects an ongoing trend towards more effective mine site integration and optimisation. Constrained sampling that reflects and defines inherent ore body variability is a key geometallurgical requirement. This requires use of larger numbers of low-cost physical testing which can be applied to small sample volumes suitable for defining natural variability. The AMIRA P843 'GeMIII' project (Geometallurgical Mapping and Mine Modelling) is a major industry-supported research initiative designed to develop new tools, methods and protocols to support geometallurgical integration. As part of this integrated research a new more rapid low-cost comminution test (GeM Comminution index) has been developed which can be employed as a front line tool for geometallurgical mapping purposes and predictive throughput modelling. The test has been designed to be inserted into routine assay sample preparation and is based on constrained jaw crushing protocols linked to analysis of resultant size distributions. Extensive validation and modelling has shown the GeM Comminution Index (Ci) is correlated with the Drop Weight index A*b and Bond Mill Work Index (BMWi). Large scale trials have been conducted within a commercial assay laboratory to demonstrate and optimise incorporation of the Ci test into routine sample preparation protocols. While Ci based estimates of A*b and BMWi are not as precise compared to larger volume more expensive test-work, the ability to undertake large numbers of tests typically in a systematic down-hole manner, provides a high level of data support through adjacency. A Ci based approach is highly suitable for variability mapping, domaining and selecting large composite samples for more precise testing. Within the context of the AMIRA P843 project this forms part of an integrated work flow designed to support geometallurgical integration. The development of a comminution test linked to routine assay sample preparation represents significant value adding to a process that in most cases is already going to be carried out. This paper introduces the Ci test concept and application to geometallurgical testing for throughput modelling

Sep 13, 2010

By John J. Sammarco

Mining has one of the highest annual average fatality rates among major US industries. Health and safety dangers have been inherent to mining since the early days of picks and shovels. Even though miners’ health and safety has improved over the years, mining is still one of the most dangerous occupations. Mining was traditionally a low tech industry. It is now driven by competitive pressures to go high-tech by using programmable electronics (PE) for machine control, atmospheric monitoring and material processing. The industry’s experience with the functional safety of PE is limited compared with other industries. Thus, PE is an emerging technology for mining that can potentially create or worsen hazards.

Jan 1, 1999

By R. H. Lien

The Bureau of Mines has conducted research on a flue gas desulfurization (FGD) process as part of its goal of minimizing the undesirable environmental impacts associated with sulfur dioxide (S02)-bearing waste gases. This FGD process, referred to as the modified citrate process, involves absorption of S02 in a buffered citric acid solution. The absorbed S02 is subsequently stripped from the solution using steam, which regenerates the solution and produces a wet S02 product. This product can be further processed to make sulfuric acid or liquid S02. Economic evaluations showed the process to be expensive when the stripper was operated at or near ambient pressures because of the large amounts of steam required for solution regeneration. Research was directed at reducing steam consumption in the stripper. The effect of stripper pressure on steam consumption was investigated. A process research unit (PRU) was operated with the stripper pressurized in the range of 5 to 150 psig. Test results showed that steam consumption decreased with increased stripper pressure. For example, when operating the PRU stripper at 150 psig, 4.1 grams of steam per gram of S02 was required to remove 90 pct of the S02 from a 1.0-vol-pct-S02 gas. This compares to 7.1 grams of steam per gram of S02 required for 90-pct S02 recovery at 5 psig.

Jan 1, 1982

By M Sherman

The challenge facing the engineering provider is to calculate throughput rates when faced with disparate specific energies calculated by different testing methodologies. Typically, an ownerÆs team would expect that the throughput calculations be checked using more than one method, therefore it is inevitable that there will be differences, based on which methodology is used. This engineering challenge is exacerbated by the continuing evolution of contemporary circuit configurations such as two stage pebble crushing with or without high pressure grinding rolls (HPGRs) as the second stage, or second stage pebble crusher product reporting to the ball milling circuit, etc.This paper is a companion to the paper first presented at SAG 2011, which showed that the Bond Indices are an excellent tool for estimating the specific energy requirements for semi-autogenous grinding (SAG) mills in single-stage SAG milling (SSS) circuits, SAG and ball mill circuits (SAB) or SAG and ball mill circuits with pebble crushers (SABC). This paper presents how the Bond Indices have been used to calculate ball mill specific energies, and therefore throughput rates, for SAG mill based circuits. Once the ball milling specific energy is known, tower mill and vertimill energy requirements can also be calculated. It is noteworthy that the method presented in this paper does not require the use of any unpublished correction factors: the proposed method uses the Bond parameters and equations published by Rowland in 1982.CITATION:Sherman, M, 2013. 21st century bond, in Proceedings Iron Ore 2013 , pp 309-312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013