Search Documents

NIOSH research has focused on the monitoring and the control of methane levels in active mine workings. Response times for instrumentation using catalytic heat-of-combustion sensor technology were evaluated. NIOSH research has modelled the flow of methane gas onto long-wall faces and gobs, developed engineering controls to limit methane levels during mining, and designed coalbed and gob degasification systems. Available methane control systems have been challenged by recent developments in longwall and room-and-pillar mining systems. This includes increased face advance rates leading to increased productivities, increased longwall panel sizes, and the generally deeper workings of U.S. coal mines. The potentially violent nature of any underground explosion or ignition requires the measurement, control, and reduction of methane emissions into the mine environment for continued worker safety.

Jan 1, 2008

By Jean-Louis Briaud

The following is a summary of a very recent report prepared at Texas A&M University for the National Cooperative Highway Research Program and entitled "Downdrag on Bitumen Coated Piles". Anytime the soil settles more than the pile, downdrag or negative skin friction will develop. The load in the pile increases with depth up to a certain point and then decreases down to the pile point. This phenomenon has been quoted as being the number one culprit for deep foundation failures. In Chapter 1, an introduction to downdrag is given. The most common criterion for downdrag is to consider it in design as soon as the settlement of the soil surface after pile driving exceeds 0.5 in. Coating piles with bitumen is an effective way of reducing downdrag forces and therefore allows to use smaller piles for the same load. This results in cost savings. Coating piles with bitumen increase the cost of piles by about 33% and therefore the decision to use bitumen is generally based on economic considerations.

Jan 1, 1989

By J. D. Potts

Installation of a horizontal air blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong coanda effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector to bailing airflow ratio, and a 5.1-cm (2-in) gap between the shroud and ground. The shelf was 15.2-cm (6-in) wide and located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2009

In 1991, Placer Dome Venezuela established a 70% stake in Minera Las Cristinas, to mine the Las Cristinas gold deposits in Bolivar. This case study examines the multi-sectoral partnership arrangement that was developed to improve health services near the proposed Las Cristinas gold mine. The investment climate in Venezuela is uncertain and the socio-economic circumstances are potentially hostile. Despite that, the partnership between the mining company, local communities, government agencies and an international health nongovernmental organization (NGO) collectively leveraged nearly $2.5 million to build and operate a community health center.

Jan 1, 2002

By Robert Hopler

In accordance with the 57th section of the Explosives Act, 1875, the following report on the working of the Act during the year ending December 31, 1903, is submitted. There have been no modifications of the law during the year. No complaint is made of any falling off in the general condition of factories and magazines, and in one instance only during the year have legal proceedings been taken for any irregularity. The occupiers of factories and magazines have invariably shown perfect readiness to remedy any defects, and the managers have themselves in many instances introduced improvements tending towards greater safety. The number of deaths (5) from accidents by fire or explosion in the manufacture of explosives is below the average for the decade (6•4). Looking to the large number of persons employed in this trade, the number of deaths is not excessive and will compare favorably with the death-rate in other dangerous trades. Notwithstanding the large increase in the manufacture of explosives, the average number of deaths has greatly decreased since the passing of the Explosives Act, whereas the number of fatal accidents with explosives under conditions to which the Act does not apply appears to increase with the extension of trade.

Jan 1, 2006

In line with DML Resources continual forward management policies, the Roscommon Quarry operation has recently installed and commissioned a Nordberg 7 ft Symons cone crusher and a HP 300 cone crusher. Both machines have enhanced the production capabilities and quality control of the Roscommon comminuition circuit and they will provide efficient and reliable crushing well into the next century.

Jan 1, 1994

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

Australia's iron ore industry is entering a challenging period with the development of new orebodies, the introduction of new products and the push for further downstream processing. In addition, the recent price reductions for iron ore exports have intensified the focus on reducing capital and operating costs. To assist in these areas, CSIRO is expanding its research capabilities, including the incorporation into CSIRO of the Mineral Processing Laboratories in Perth, which were previously managed by the WA Department of Minerals and Energy. In addition, a large part of the $24.4 million expansion of CSIRO's Pinjarra Hills laboratories in Brisbane will be devoted to enhancing iron ore processing research, providing purpose built laboratories and large process bays.

Jan 1, 1999

By Leeming. J. R.

In the UK, powered supports are normally salvaged from longwall faces on completion of production, for reuse on the next unit. Where a spare set of supports are held, the salvaged supports are often stored in underground roadways awaiting installation. One mine in the UK extracts a 5m section, and holds two sets of 2x950t powered supports, each weighing approx. 35t and having closed dimensions of 8m long, 2.5 high and 1.75m wide. As the first set would not be required for over 12 months, and because of space limitations below ground, it was decided that the supports would be left in situ, the district sealed, and reopened at a later date for support salvage. The paper described the decision making process, and the inertisation of the sealed district utilising nitrogen generated on the mine surface and piped to the point of use. The re-entry and re-ventilation of the district are also described. The paper then goes on to describe in more detail the discovery of a spontaneous combustion event that occurred in the waste behind the powered supports, and its treatment and control using extra nitrogen brought to the mine by tanker and introduced at strategic locations along the faceline via boreholes, leading to a successful salvage and re-sealing.

Jan 1, 2009

By M. Kinne

Catalyst preparation/ characterization Slightly modified DP (~Schumacher et al. Catal. Lett. 89, 109, 2003) CeO2 HAS 15 from Rhodia calcined in air for~ 2h BET: ~188m2/g, particles size: 5.7nm (TEM, XRD) + HAuCl4 at pH of 6.5-7, (>95% of the Au was deposited) ? Au/CeO2 (2.6wt% Au, ICP-AES) A new conditioning procedure was applied, including heating at low temperature in N2 and H2/N2 mixtures) Patent DE 10205873A1. Very small Au particles <2nm, for CO oxidation catalyst as Au/TiO2, Au/Fe2O3, and Au/Co2O3 Here Au particles size <3.5nm (XRD) Summary ? CO is nearly exclusively adsorbed on the Au particles ? Positive reaction orders of 0.5 are found for CO and H2O ? Ea= 40kJ/mol ? The catalyst is very active and stable ? During WGS reaction huge amounts of formates are formed and cover the surface ? The activity of the catalyst seems to be correlated with the formate species.

Oct 1, 2003

By K. R. Griffin

Atmospheric conditions underground are constantly changing and from a safety perspective, it is critical to identify when conditions are trending abnormally. Atmospheric monitoring in underground coal mines allows mine operators to analyze atmospheric conditions underground in real-time. Real-time monitoring can then be used to identify whether atmospheric conditions underground have become problematic. The implementation of a risk assessment and management process allows operators to then use a risk-informed decision making to identify comprehensive site specific ventilation parameters. Establishing risk-informed ventilation parameters and tracking conditions relative to these parameters, management can modify ventilation plans as mine conditions develop to manage evolving risks. Ventilation risk assessment and management allows developing atmospheric monitoring technologies to be fully utilized in order to increase safety standards in the United States. This paper reviews general risk assessment approaches, state of the art ventilation based risk assessment, and the risk assessment and management application within the United States regulatory framework.

Feb 27, 2013

By Fredrick M. Ryan

Present indications are that in about 2-3 years phosphor tags will be required in commercial explosives. A permissible 254 run ultraviolet lamp assembly has been developed to permit mine inspectors to detect such phosphor tags and therefore to establish if non-permissible explosives were used. This new lamp is powered by a Miner&apos;s cap battery without interference with the normal lighting requirements of the cap lamp battery. It is compact, light, and rugged with very high ultraviolet output.

Jan 1, 1977

By Thomas G. Murdock

The possible contribution of an improved mineral economy to the further advancement of the lesser developed regions of the world is a vital consideration today. Many of the newly independent countries recognize the problems and the challenge involved in orderly development of mineral resources. Some countries are inventorying resources, planning development, and encouraging local and foreign participation. The Malagasy Republic, composed of the island of Madagascar and the immediately adjacent islands, formerly the French Overseas Territory of Madagascar, is one of the members of the French Community which achieved independence in 1960. It is making real progress towards improving its mineral economy, an effort particularly remarkable considering the generally unfavorable geographic location of the area with respect to world markets and what is, after all, a comparatively sparse economic mineralization in the light of discoveries to date. Most of the development of the Malagasy econorny before independence was fostered by French private enterprise, although the State participated in some ventures. Since independence, the Government has encouraged private investment from a variety of sources through favorable legislation and has indicated that legitimate investment projects that will further advance social and economic programs will be welcome.

Jan 1, 1963

By Edward A. Barrett

The ability to recognize visual cues commonly associated with roof and rib hazards is fundamental to the prevention of groundfall accidents. The perceptual skills that miners possess to visually search and assess hazardous ground conditions differ considerably. This U.S. Bureau of Mines report summarizes recent investigations on the use of stereoscopic (3-D) slides as a training aid for improving the ability of miners to recognize the various geologic and mining-induced irregularities that cause ground-falls. The feasibility of using 3-D slides for training and their effectiveness for representing roof and rib hazard conditions are discussed. Information is presented on equipment and procedures for creating a 3-D slide program that can be updated by mine trainers. Recommendations are made on selection of 3-D equipment and on the use of 3-D slides for training miners to recognize roof and rib hazards.

Jan 1, 1988

By Charles H. Etheridge

A new filter cassette is described which can be used with Coal Mine Dust Personal Sampler Units (CFR, Title 30, Part 74). The sealed cassette design reduces the chances of sample loss due to reverse flushing, impact or cassette opening. The filter capsule weight is approximately 400 milligrams and is stable for at least one year in storage. The alpha quartz content of the filter element is less than 5 nanograms per square millimeter of surface. The cassette is designed to be used with a new sampling head. The manufacturing costs of the new cassette will require an increase of approximately 30% in the selling price.

Jan 1, 1978

By A. Feldman

Measuring dynamic effects on existing structures such as dams and bridges during earthquakes or blasting is frequently done using strong motion detectors. However, a more comprehensive dynamic structural evaluation requires direct measurement of deflection, strain, and pressure changes during dynamic events. Many existing structures have vibrating wire gages already installed that can be used with modifications to the data acquisition systems to provide direct measurement of dynamic displacement, strain, and pressure. The project described in this paper provided the opportunity to demonstrate the feasibility of using vibrating wire technology to measure dynamic effects on existing structures.

Jan 1, 2006

By P. E. Fitzgerald, J. C. Gindlesperger

1. The Acidizer (Trade Publication of Dowell Inc.): No. 1. Aspects of Acidizing. No. 2. Inhibited Acid. No. 3. The Value of Acidizing. No. 4. The Chemistry of Acidizing. No. 5. Jelly Seal in Acidizing. No. 6. Loosening Stuck Drill Pipe. No. 7. The Geology of Acidizing. 2. J. C. Albright: Acid Is Being Used for Cleaning Intake Wells in Water-flooded Areas. Oil Weekly (Sept. 23, 1935) 24. 3. D. H. Bancroft: Acid Tests Increase Production of Zwolle Wells, Miller County, Arkansas. Oil and Gas Jnl. (Dec. 22, 1932) 42. 4. A. H. Bell: Possible Areas for Acid Treatment in Illinois. Pub. of Illinois- Indiana Petr. Assn. and lllinois Geol. Survey (1934) 49. 5. N. A. Best: Treating Limestone Formations Consists of More than Pouring Hydrochloric Acid in the Well. Oil and Gas Jnl. (April 5, 1934) 54. 6. L. G. E. Bignell: Sealing Off Salt Water from Oil-bearing Formations. Oil and Gas Jnl. (Jan. 30, 1936) 59. 7. L. G. E, Bignell: Acidizing Upper Limestone Formation Facilitated by the Use of Jelly Seal. Oil and Gas Jnl. (March 5, 1936) 30. 8. L. G. E. Bignell: Bailing, Shooting, Tubing and Acidizing Have All Been Tried in Deep Test at Binger, Oklahoma. Oil and Gas Jnl. (May 10, 1934) 38. 9. L. G. E. Bignell: Dowel1 Incorporated Increasing Its Field Service for Acid Treatment of Wells. Oil and Gas Jnl. (June 7, 1934) 62. 10. L. C. Chamberlain, Jr. and P. E. Fitzgerald: Oil Well Acidizing in Michigan. Mich. Acad. Sci. Papers (March 1937). 11. M. E. Chapman: Some of the Theoretical and Practical Aspects of the Acid Treatment of Limestone Wells. Oil and Gas Jnl. (Oct. 12, 1933) 10. 12. C. E. Clason and J. G. Staudt: Limestone Reservoir Rocks of Kansas React Favorably to Acid Treatment. Oil and Gas Jnl. (April 25, 1935) 53. 13. W. F. Cloud: Cleaning and Reconditioning Oil Wells—Reconditioning by Use of Acid (Petroleum Production 1937), 389. University of Oklahoma Press, 1937,&apos; 14. K. A. Covell: Developments in Eastern Production Practice. Acid Treatment of Michigan Wells. Amer. Petr. Inst. Prod. Bull. 213 (1934) 77; Oil and Gas Jnl. (May 31, 1934) 89; Oil Weekly (May 28, 1934) 17. 15. B. A. Cunningham: Acid Treatment of Lime Formations. Amer. Petr. Inst. Paper 901 (1933) 9D, 1-7. 16. 0. I. DeSchon: Pondera Production up 22,000 Barrels. Montana Oil & Min. Jnl. (Jan. 26, 1935) 1.

Jan 1, 1937

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

By S. K. V. Avasarala

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading tests and installation of over 3,300 prestressed concrete piles for a building complex consisting of 12, 5- and 6-story over parking buildings. The project was recently completed in three-phases over a span of 4 years. The subsoil conditions were explored by performing 25, Standard Penetration Test (SPT) borings throughout the site. Various types of driven pile foundations were considered and following an evaluation of high structural loads and site-specific constraints such as variable depth of bearing layer of Florida limestone and quality of clay and limestone layers, a prestressed concrete pile support system was selected as the most economical and effective foundation approach. The building foundations were designed for a pile capacity of 353 kN (40 tons) in compression, 45 kN (5 tons) in lateral capacity for a deflection of 0.64 cm (0.25 in.), and 133 kN (15 tons) in uplift capacity. The axial and lateral allowable pile capacity and lengths were predicted using SPT91 and LPILE computer programs, which are generally used in Florida. The validation of these capacities was derived from 144 probe piles and performance of 12 pile loading tests on selected probe piles. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the loading tests on probe piles. This information was effectively utilized as part of the overall quality control program to install a total of 4,186 prestressed concrete piles (including 144 probe piles) in different building areas across the project site to depths ranging from 8 to 21 m (25 to 90 ft) below existing ground elevation as part of foundation support system. This engineered, monitored, and tested foundation solution provided an effective and satisfactory basis for completion and approval of the foundation work for this 12, 5- and 6-story over parking building complex. A recent reconnaissance has indicated that all the building foundations are performing satisfactorily.

Jan 1, 1995

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004