Search Documents

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

By Innes J. A

The structural variations occurring in pellets of finely divided mixtures of iron ore and coke breeze, metallized by firing at elevated temperatures, have been examined microscopically. For any given pellet composition, time and temperature are the two most important factors in determining the development of the bonding processes.INTRODUCTIONThe success of sintering and pelletizing processes in the agglomeration of fine iron ores for blast furnace use has brought about rapid changes in thinking relative to methods of preparing furnace burdens. Increases in productivity with the use of sinter emphasize the advantages of a stable, uniformly sized furnace feed. Current practice is to produce a self-fluxing sinter containing most of the lime requirements of the furnace incorporated as a stable medium (Figgis and Charker, 1962). The elimination of fine material from the burden allows greater stack permeability and smoother operation.Sintering and pelletizing of iron ores with or without the incorporation of fluxing compounds has conditioned operators to the extent that it is now considered possible that all components of the burden may eventually be beneficiated in one form or another. Investigations are in hand to improve the quality and sizing of coke, which occupies the major part of the burden volume (Callcott, Innes and Brown, 1961; Innes, Gregory and Worner, 1963). Interest is also being revived in methods of pre-reducing iron ores prior to charging to the furnace (Hansen, Melcher and Fine, 1961). Recent experiments in a small experimental blast furnace (Melcher, 1963) show that charging of semi-metallized pellets can give rise to a production increase of 55 per cent...

Jan 1, 1963

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By H Thanasekaran, J Kohmuench, B Seaman

To achieve an efficient separation in the flotation process, valuable particles need to be selectively segregated from the gangue while utilising a minimum number of flotation stages. TodayÆs existing flotation technologies are effective for fine particle size classes; however, limitations due to particle buoyancy and bubble-particle detachment restrict the effectiveness of traditional flotation approaches on coarser particles. As a result, flotation circuits are generally configured to process only fine particle size classes in order to maximise recovery in the primary stages. Eriez has invented a novel flotation technology, the HydroFloat, which overcomes these limitations by carrying-out flotation in a dense, fluidised-bed medium allowing for the recovery of coarse particles (>0.250 mm). Over the last 15 years, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3 mm diameter in primary flotation circuits. This paper includes discussions on the history of this technology, process theory, existing applications, and a review of recent sulphide-based laboratory test work conducted for Newcrest mining and others. Benefits of this approach, such as improved recovery, low energy consumption and reduced reagent addition will also be reviewed.CITATION:Kohmuench, J, Thanasekaran, H and Seaman, B, 2013. Advances in coarse particle flotation - Copper and gold, in Proceedings MetPlant 2013 , pp 378-386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Kenneth J. Hartman

Introduction The term kaolin is derived from kauling, a Chinese word meaning high ridge. This was the name of a hill in China where kaolin was first mined several hundred years ago (Murray, 1976). Other common names used for kaolin include clay and China Clay. Clay technically has a broader meaning and could refer to bentonite and ball clay as well as kaolin. China clay, as a descriptive term, apparently results from kaolin's origin. But it could also be due to a significant historical use in ceramic applications. The terms kaolin and clay will be used interchangeably in this analysis because of the common practice of using these terms in the paper industry. Major reasons for kaolin's wide-spread industrial usages center on kaolinite's physical features of good color, low viscosity, and inertness. Kaolin is described as a hydrous aluminum silicate with an approximate composition of 2H2O • A12O3 . 2SiO2. A new version of the product is calcined clay with modified hydration content. It is gaining widespread use. Components of any particular kaolin, in addition to alumina and silica, are viewed as impurities. The more values deposits and, hence, higher priced kaolin products are those of the highest purity. Kaolin is the most widely used mineral in paper manufacturing throughout the world. Key production centers are located in England and the US. Most of the Tatter's production is located in Georgia. The key markets for Georgia kaolin are paper markets - both paper coating and paper filling. These paper markets extend throughout the world, not just to domestic markets. In fact, export markets are second in size only to domestic paper markets for Georgia's producers of kaolin. Just as the paper markets are important for kaolin producers, kaolin is an important raw material for papermakers. Compared to the other three major pigments - titanium dioxide, calcium carbonate, and talc - kaolin's 1984 tonnage for papermaking represented 85% of the total. Even though titanium dioxide's unit value is much higher, kaolin's estimated total 1984 value still represented 51% of total dollars spent by papermakers for the four pigments. Kaolin grades- are briefly defined using particle size and brightness as principal means of classification. Likewise, grades of papers using kaolin are defined using the American Paper Institute's guidelines. From these definitions, associated kaolin grades used in particular grades of paper are reviewed. Special emphasis is placed on how qualities desired in certain papers are achieved through the use of specialized kaolin grades. World kaolin production World production statistics (Coope, 1979; Table 1) demonstrate that kaolin is produced in many areas of the world. About 60% of production is centered in the US and England (Fig. 1). Deleting Eastern Europe's produc-

Jan 4, 1987

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By T. P. R. de Jong, H. Harbeck

"This contribution reports recent mineral sorting experience and lists the opportunities of the newest generation of automatic sorters with a special focus on electromagnetic detection and Xray transmission. With the available sensor resolutions and actuator systems that are available today sorting of minerals down to 2 mm size and up to 250 mm lump size is technically feasible. In industry, ore as well as coal is still hand-picked and current automation potential only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs.They are:??High speed and high resolution sorting systems based on X-ray transmission imaging??High speed on-line image processing and further development of advanced data processing??Modular multi-sensor automatic sorting units (using one or more sensors such as colour, electromagnetic and X-ray in a single device)??Sensitive electromagnetic sensors for sorting based on differences in magnetic susceptibility and electric conductivityThe above enables compact dry separation, insensitive for moisture fluctuations and at high separation sharpness, as well as “electronic” high gradient magnetic separation for larger particles. Besides conventional X-ray transmission (XRT), dual-energy XRT (DE-XRT) is now being redesigned to meet the requirements of the mining industry. The mentioned technologies provide automatic dry separation of minerals and rock as alternative for conventional processing."

Jan 1, 2005

By Piyush K. Dutta

This report describes the design, development, manufacture and incorporation of noise control features on a jumbo drill and the results of successful tests of this drill in surface and underground mines. The noise-reducing features developed under this program are applicable to future designs of jumbo mounted drills that can be cost effectively manufactured and have the potential to reduce noise levels at the operator's position from 115-120 dBA to 95 dBA or less without a reduction of currently attainable drilling rates.

Jan 1, 1985

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006

By Mohammed Y. Fattah, Wissam H. S. Al-Sudani

"During installation of pile, a soil column is formed inside the pile. For small depths, the height of the soil column typically equals to the penetration depth (full coring state). As the penetration depth increases, the developed internal shear stresses become larger and reduce the amount of soil to penetrate. At the same time, the soil in pile at the bottom is compacted. This will continue until at a given moment, the soil column is a soil plug, and does not stop moving relative to the pile. This is because the shear stresses developed in the interior of the pile are greater than the load-bearing capacity of the ground.This paper presents the results obtained from 40 model pile tests carried out to assess the effect of soil plug on the model pile capacity. The piles are embedded in sand of different densities with different lengths of piles and types of pile-ends. The model tests are divided into two parts according to the type of end of the pipe pile used in the model pile test. The first part consists of 32 model open-ended piles with different lengths of soil plug inside the pile. The second part consists of 8 model closed-ended piles.It was concluded that open-ended pipe piles behave as a closed-ended if the soil plug formed inside piles in state partial plug or full plug. Length of soil plug depends on the type of installation and relative density. The pile load carrying capacity in dense sand is several times greater than those in medium sands especially in cases of closed ended piles or open-ended since the pipe pile can produce external and internal skin friction in addition to end bearing resistance that makes the total pile capacity close to that of closed-ended pile. Whether open-ended piles are driven or pressed in the fully coring - fully unplugged mode or in the partially plugged mode, the plug does contribute to static pile base capacity."

Jan 1, 2014

By F. F. Roberto

Many techniques that are used to characterize and monitor microbial populations associated with sulfide mineral bioleaching require the cultivation of the organisms on solid or liquid media. Chemolithotrophic species, such as Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans, or thermophilic chemolithotrophs, such as Acidianus brierleyi and Sulfolobus solfataricus can grow quite slowly, requiring weeks to complete efforts to identify and quantify these microbes associated with bioleach samples. Real-time PCR (polymerase chain reaction) assays in which DNA targets are amplified in the presence of fluorescent oligonucleotide primers, allowing the monitoring and quantification of the amplification reactions as they progress, provide a means of rapidly detecting the presence of microbial species of interest, and their relative abundance in a sample. This presentation will describe the design and use of such assays to monitor acidophilic microbes in the environment and in bioleaching operations. These assays provide results within 2-3 hours, and can detect less than 100 individual microbial cells.

Jan 1, 2009

Estimating Particle Size Fraction Proportions - A Multiscale Approach Using Multiple Kernel Learning

Sep 13, 2010

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006

By Paul C. Schmall, Thomas Tuozzolo, Arthur B. Corwin

The Lenox Avenue Reconstruction Project involved the excavation and replacement of 750 m (2,500 ft) of deteriorated subway invert concrete, 5 to 7 m (15 to20 ft) below water table in very permeable ground. The Replacement work was done over an 8 month period, while maintaining track service through this subway section. The project was dewatered with a single 125 l/s (2,000 gpm) wellpoint system,750 m (2,500 ft) in length, which was installed from inside the active tunnel structure and configured to coexist in the subway tunnel with operating trains as well as the construction activities. A thin diaphragm jet grout wall was utilized on one end of the site to cut off the flow of water across a difficult geological interface that was situated immediately below the tunnel invert. The thin diaphragm jet grout wall permitted the large 116th Street Station area to be dewatered completely with well points from outside of the excavation.

Jan 1, 2001

By A. K. Anyimadu

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004,and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November 2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Keywords: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, platinum, palladium, PGMs, tailings.

Jan 1, 2007

By Willie M. NeSmith, W. Morgan NeSmith, Alan Roach

"In 2013, Augered Cast-in-Place (ACIP) piles are a mature foundation technology throughout the United States. General guidelines for the design and construction of ACIP piles are available along with numerous references for design in specific North American geologies. In fact, the current generation of contractors and geotechnical practitioners might view ACIP piles as just another deep foundation option to be considered, along with driven piles, drilled shafts and others. This acceptance has developed, however, over a 60-plus year period.The term, Augered Pressure-Grouted (APG) pile is often used when referring to ACIP piles because the piles emerged out of construction processes at the Intrusion-Prepakt firm in the late 1940s. The company’s specialty was pressure grouting and preplaced aggregate concrete. The grouting was typically accomplished by driving a pipe to a target level and then injecting grout under pressure. In some soil conditions, it was necessary to use an auger to reach the desired grouting depth. In these circumstances, the grout pipe was driven beside the auger and grout was pumped as the auger was withdrawn. The grout pipe was then withdrawn as well. This was the genesis of the APG, or ACIP pile, and many piles were installed using this technique. The patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies Patent, LicensesThe patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies coined their own terms for the piling process: “Pakt-In-Place” for Intrusion-Prepakt, “Auger Pressure-Grouted” for Berkel and “Augercast” for Turzillo. Over time, “Augercast” was frequently used as a generic term for the system. The installation of these piles was, and still is, a highly nuanced process; “contractor dependent” is a term often seen today. Intrusion-Prepakt, Berkel and Turzillo all had personnel who were part of the original group that developed the system and who appreciated the craftsmanship involved in forming sound piles."

Jan 1, 2013

The following Inventory was prepared to provide mineral deposit data to the U.S. Army Corps of Engineers for use in the Resource Development Navigation Study in Alaska. The inventory was prepared using data contained in the U.S. Bureau of Mines Minerals Availability System (MAS) database. The Alaska portion of the database contains Information on over 7,000 mineral locations and deposits throughout the state. When MAS was established In 1975, database entries were originally compiled from literature searches by both Bureau personnel and contractors. Deposit data are obtained/maintained through Information gained from a variety of sources, Including published and unpublished Bureau of Mines reports, records, and files; U.S. Geological Survey (USGS) Bulletins, Professional Papers, and other reports; technical and professional Journals; State and other Federal agency publications; data generated during field examinations; and information obtained from knowledgeable individuals. Because of the size of the data base, many of the data have not been significantly modified since initial entry. Each deposit on the MAS data base has a sequence number of the following form:

Jan 1, 2011

Orebodies are defined in economic terms in that they must satisfy conditions determined by costs of mining, extraction and marketing before being so described. Despite this they have an essential chemical character as specialized products resulting from geochemical differentiation, and it is surprising that so little basic geochemical research has been carried out with respect to ore occurrence and that prospecting methods based on geochemical principles are not more widely applied.Many exploration geologists associate geochemistry with analytical techniques applied to the detection of dispersed traces of metals from actual orebodies. Geochemical research, applied to economic geology, goes far beyond this limited field and the purpose of this paper is to discuss aspects of such research and its use in formulating exploration principles.THE GEOCHEMICAL BACKGROUND TO MINERAL OCCURRENCE AND EXPLORATIONThe three aspects of economic mineral deposits to which geochemical research can be of use in determining ore guides are genesis, control of deposition and mode of dispersion from orebodies after emplacement. Prospecting for mineral deposits is primarily based on theories of ore occurrence which deal with the genetic and depositional influences controlling localization of ore. There are many such theories and they will not be discussed here as they have been adequately reviewed in geological publications. Some are based on differing argument concerning the same empirically observed associations of ore. In this respect it is perhaps fortunate that they are not always mutually exclusive as regards the...

Jan 1, 1960

By Sashir Estela De la Cruz

Actualmente la informática como herramienta aplicada al sector minero nacional, es importante -en tanto su empleo adecuado y racional implica alcanzar los objetivos planteados en forma más rápida y con mayor calidad. En este sentido, el presente texto describe el sistema informático que genera soporte al trabajo de modelamiento geológico para la estimación de reservas mineras, de forma que reduce el tiempo y personal empleado en dicha labor. Este sistema se divide en dos partes: estadístico y gráfico y determina la explotación de un prospecto de yacimiento minero.

May 25, 1998

By R. F. Hochstein, A. J. Neale, B. C. Flintoff

"Process control technology holds very significant potential benefits for many mineral and coal processing plants. The impact can be expected in terms of performance improvements (e.g. increased throughput, better quality control, higher availability), through reduced operating costs (e.g. lower reagent consumptions, manpower reductions) and in the form of intangibles (e.g. reduced vulnerability to manpower turnover, increased productivity in the user group). However, the installation of a process control system will represent considerable capital expenditure and will generate an operating cost. No management team would approve the funding for such a project without some reasonable measure(s) of the profitability of a proposed system. This paper describes a methodology for addressing the justification problem. Of particular interest is the approach to quantifying performance improvements, frequently found to be the predominant benefit of process control.INTROPUCTIONProcess control has become widely recognized as an essential component of any processing operation. It has direct impact on productivity, process efficiency and product marketability. The reported pay backs associated with successful installations underscore this observation. As a consequence, many operators who have little in the way of process automation are looking to initiate control projects, while those who currently enjoy some level of automation are looking to upgrade existing control systems (= process + instrumentation + hardware + software + operators + support). While the emphasis here would appear to be on retrofit process control projects, new plants, or those currently in the design stage, will usually find themselves in one of these categories shortly after startup 1."

Jan 1, 1990