Search Documents

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

By Paul J. Axtell

Self-hardening cement-bentontie (c-b) slurry walls were constructed as shear walls to stabilize the downstream slope of Tuttle Creek Dam near Manhattan, Kansas. The slope stabilization was required to protect the existing pressure relief well system located at the downstream toe of the dam. The wells require protection from slope deformation induced by liquefaction of the foundation sands during or immediately after the design seismic event. The shear walls are transverse to the axis of the dam, unreinforced, and relatively brittle members that may be exposed to relatively large shear strains, and possible cracking, during or immediately after shaking. An extensive laboratory investigation was conducted on recovered core samples to optimize the mix design and stabilization scheme. Furthermore, as is the topic of this paper, a portion of the laboratory investigation was to determine the large-strain, or post-peak, shear strength of the c-b material for use in limit-equilibrium slope stability analyses and numerical deformation modeling to assess the magnitude of permanent deformation caused by the design earthquake. These data may be beneficial to other projects that are considering the use of unreinforced c-b slurry walls for seismic retrofit purposes.

Jan 1, 2010

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

By A. Rejeb, A. Millard

ABSTRACT: An evaluation of the importance of the thermo-hydro-mechanical couplings (THM) on the performance assessment of a deep underground storage design has been made as part of the international DECOVALEX III project. It is a numerical study that simulates a generic repository configuration in the near field in a granite medium. The thermo-hydro-mechanical evolution of the whole configuration is simulated over a period of 100 years. The model used to represent the unsaturated behaviour of the various porous media makes allowance for moisture transfers through the effect of thermal and water gradients. The paper presents a comparison of the temperature, water pressure and stress fields obtained by TM, TH, HM and THM coupled calculations. The results demonstrate that temperature is hardly affected by the couplings. In contrast the influence of the couplings on the mechanical stresses is considerable. This is attributed to the key role that water has on bentonite swelling or shrinkage effects that are dependent on its saturation level variations. KEY WORDS: Modelling, thermo-hydro-mechanical couplings, temperature, pressure, stress. ZUSAMMENFASSUNG : Im Rahmen des internationalen Projekts DECOVALEX III wurde untersucht, wie groß der Einfluss thermisch-hydraulisch-mechanischer Kopplungen (THM) auf die Leistungsfähigkeit eines Konzeptes zur Lagerung hoch radioaktiver Abfälle zu bewerten ist. Bei dieser numerischen Behandlung wird eine generelle Lagerungskonfiguration in granitartigem Milieu simuliert. Die thermisch-hydraulisch-mechanischen Prozesse werden für eine Dauer von 100 Jahren simuliert. Bei dem Modell, mit dem das Verhalten der verschiedenen, unterschiedlich porösen Milieus in ungesättigtem Zustand dargestellt werden soll, werden die Feuchtigkeitstransporte infolge thermischer und hydraulischer Vorgänge berücksichtigt. Verglichen werden in diesem Artikel verschiedene Temperatur-, Wasserdruck- und Beanspruchungsfelder, die sich aus TM-, TH-, HM- und THM gekoppelten Berechnungen ergaben. Dabei stellte sich heraus, dass die Temperatur nur gering von den Kopplungen berührt wird. Die Einflüsse der Kopplungen auf die Mechanik sind hingegen bedeutend; ausschlaggebend dafür ist der Faktor Wasser, der den Bentonit je nach Sättigungsgrad quellen oder trocknen lässt. SCHLÜSSELWÖRTER: Modellbildung, thermisch-hydraulisch-mechanische Kopplungen, Temperatur, Druck, Beanspruchung. RESUME : Dans le cadre du projet international DECOVALEX III, une évaluation de l’importance des couplages thermo-hydro-mécaniques (THM) sur les performances d’un concept de stockage de déchets fortement radioactifs a été menée. Il s’agit d’une étude numérique simulant une configuration générique de stockage en champ proche dans un milieu granitique. L’évolution thermo-hydro-mécanique de l’ensemble est simulée sur une période de 100 ans. Le modèle utilisé pour représenter le comportement non saturé des différents milieux poreux prend en compte les transferts d’humidité sous l’effet de gradients thermiques et hydriques. L'article présente une comparaison des champs de température, de pression d’eau et de contraintes obtenues par des calculs couplés TM, TH, HM et THM. Les résultats montrent que la température est peu affectée par les couplages. En revanche, l’incidence des couplages sur la mécanique est importante; ce qui est attribué au rôle majeur joué par l’eau à travers les effets de gonflement ou de retrait de la bentonite selon la variation de son degré de saturation. MOTS-CLEFS : modélisation, couplages thermo-hydro-mécanique, température, pression, contrainte.

Jan 1, 2003

The poor reconciliation between the values of estimated and actual grades can cause major economic losses to the mining industry. In a mining operation grade reconciliation is comparing the values of estimated grade calculated in exploration stage with actual grade obtained from blastholes' data. Many different factors affect the degree of reconciliation in a mining operation. In this paper we investigate the factors related to estimated grade which affects the reconciliation process in the exploration stage of the orebody. These factors are the sources of uncertainty in the rest of mine life. In this area the most important factors are inherent variability, statistical uncertainty and systematic uncertainty. A probabilistic model was presented to model each source of uncertainty. The implementation of proposed model was checked and its validity was investigated using real data in an iron open pit mine in Iran.

Dec 6, 2010

By Shimi Tzobery, John E. Shamma, Samuel Swartz, Gary B. Hemphill

The trapezoidal tapered ring method has made significant progress in recent years for shielded-TBM projects, excavating tunnels with high overburden, strict water tightness criteria, and multiple curve alignments. The selection of compatible tapered rings is critical for successful advancement of the tunnel, assuring efficient installation of rings, as well as prevention of ring damage and excessive leakage. Using experience from the Arrowhead Tunnels Project, this paper describes guidelines for ring selection in tunnel curves, geometric analyses that comply with criteria principals, and provides techniques developed to determine the appropriate relative key position.

Jan 1, 2005

THIS tunnel, which is an adit 7000 ft. long, was undertaken by the Mount Lyell Mining and Railway Company Limited to connect its treatment works with the North Lyell mine at depth, with a view to effecting economies in transport and drainage. The work was carried out at high pressure throughout from both ends, and although the ground in the mine end was intensely hard, good progress was made, and driving was completed in less than fifteen months.The Mount Lyell mining field is situated in the west of Tasmania, about 20 miles inland, the only means of access being the Mount Lyell Mining and Railway Company's 3 ft. 6 in. gauge railway which connects with the Government railway system of the State at Strahan, on Macquarie Harbour. The region is mountainous, and presents many difficulties to the road and railway engineer. The West Coast range running north and south in a succession of bold prominences, which rise up to 4000 ft. above sea-level, forms the backbone of the district, and on its foothills the Mount Lyell mines are situated. The railway terminus at Queenstown...

Jan 1, 1929

By J. R. Campbell

The need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. Washability Studies The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money can hardly be spent on "feed surveys') to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus. The sizes to be examined to get the picture are optional to the investigator. In modern wet washing, the range is from 4 to 0 in. Hand-picking on properly constructed belts is perhaps the standard for cleaning above these sizes. A good picture of the coal may be obtained by the following screen analysis: 3½ to 1¼ in. 1¼ to 3½ in. ½ to 5/16 in. 5/16 in. to 14 mesh 14 to 28 mesh 28 to 48 mesh and for very complete data on the fines: 48 to 100 mesh 100 to 200 mesh and through 200 mesh

Jan 1, 1930

By Sohta Takatsu, Hachiroh Mizubata, Shigeki Kudoh, Kazuya Takekuni, Yoshinori Yamada

A special type of shotcrete is used to improve the performance of open-type TBM in difficult situations. The Hakamagoshi and Johana tunnels are expressway evacuation tunnels of 3.2 km and 5.1 km in length, respectively (total 9.1 km) that were excavated by one open-type TBM. The geological conditions at the sites were estimated to be good before excavation. However, 95% of the rock turned out to be two ranking orders worse than the estimated classes. Therefore, we used a special shotcrete for bad rock conditions, and succeeded in excavating the tunnel at an average rate of 270 m/month.

Jan 1, 2001

By C. Carlson, W. Muir

"The oxygen demand of the complex lead-zinc-iron feed at the Cyuro Anvil concentrator was determined denendent on the cyanide ion con-contration of the pulp. By redistribution of the cyanide [ ] the grinding circuit in direct proportion to the amount of surface area created, a more activated flotation feed in obtained.Monitoring the oxygen demand of the flotation feed and grinding mill discharge has proved useful in diagnosing metallurgical problems day to day operation."

Jan 1, 1976

By Hugo T. Dummett

I would like to share some observations about the mining business and place the ongoing discussion in the context of our changed world. The mining industry practices its trade in a universe defined by prices, laws and governments. Prices, as in what the industry is paid for what it produces, and the costs of goods and services. Laws that have to be transparent and fair. And governments that the industry prefers to be stable and supportive of the industry, and certainly not corrupt. However, the day-to-day realities of the mining business in 2000 are not what they were 10 years ago. Several events have occurred that have resulted in a less populated workplace that is obliged to work much smarter and faster. These include real declining prices for most mineral commodities; low and diminishing returns to company shareholders; massive restructuring of the industry through mergers, partnerships and alliances; gold’s changed role from reserve currency to just another commodity; the growing importance of native title and the startling imperatives of “sustainable development.” In addition, the “borderless world” now means that resource companies will need to pass the test of being responsible corporate guests who respect and enhance the social, moral and societal values of their host countries.

Jan 1, 2000

By S. Klein, D. Crouthamel, D. W. Farmer, S. H. Phillips

Groundwater inflows during construction pose one of the greatest risks to the successful completion of tunnel projects. Inflows can result in safety concerns, difficulty in mining and ground support, impact sensitive environmental habitats, create surface settlement and increase costs. Adequately planned pre-excavation grouting programs benefit both the Owner and Contractor in reducing risks and controlling project costs and potential schedule delays. This paper outlines strategic guidelines for assessment of site conditions for pre-excavation grouting hard rock tunnels. It also describes the design of pre-excavation grouting programs with respect to project requirements.

Jan 1, 2005

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

By D. E. Kirby

The electrochemical reduction of AlC13 was investigated as a process for the production of aluminum. An externally heated, single-compartment cell with a rammed refractory lining was used with molten KCl-NaCl-AlC13 electrolyte. Aluminum was deposited qt 700° to 760° C with a current of 100 to 200 amperes on a molten aluminum cathode. Chlorine was evolved at a graphite anode and collected and measured to provide a quantitative evaluation of the AlC13 reduction. Aluminum was removed from the cell by siphoning or ladling. Granular AlC13 was added periodically to replenish that depleted from the electrolyte. Concentrations of 7.5 to 17.5 percent AlC13 in the electrolyte were optimum for operation. Anode current efficiencies of 83 to 85 percent were attained, using anode current densities of 5.9 amperes per square inch and an anode-cathode distance of 4 inches. The chemically bonded, alumina liner was resistant to attack by aluminum and chlorine but susceptible to erosion at the surface of the electrolyte. Titanium diboride proved suitable for the electrical connection to the molten aluminum cathode. Aluminum of a purity equal to or better than 1100 series metal was electrowon continuously from commercial AlC13 for a period of 4-1/2 months.

Jan 1, 1970

By B. C. Viljoen

"SynopsisCommencement of the next phase of the Lesotho Highlands Water Project is a year or so away from becoming reality. Some 50 km of tunnels in the form of access adits, shafts, diversion tunnels, and main waterways will be constructed. Sprayed concrete will form an integral part of the temporary and permanent rock support systems that will be installed. Furthermore, the use of sprayed concrete as a final tunnel lining solution was proposed as a viable alternative to concrete linings in the feasibility studies that preceded the forthcoming implementation phase.The aim of this paper is to make the reader aware of all the sprayed concrete related issues that engineers tend to grapple with during the design and construction of tunnel projects and other underground works. Primarily, these issues would include selection of applicable design parameters, technical specifications, construction application methods, quality control and, most importantly in the context of final or permanent linings, the durability of sprayed concrete.The International Tunnelling Association (ITA) Working Group (WG) 12 has been tasked specifically to publish a set of recommendations on the Quality and Control of the Application of Sprayed Concrete and the Testing of Sprayed Concrete for Durability. These tasks were also further explored at the recent World Tunnel Congress (WTC 2015) that was held in Dubrovnik, Croatia at the end of May 2015.IntroductionSprayed concrete is presented in a variety of shapes, designs, forms, application methods and accompanying terminologies including shotcrete, gunite, pneumatically applied concrete, and the like. The International Tunnelling Association (ITA) decided to standardize on a single terminology, namely ‘sprayed concrete’, in order to simplify specification, interpretation of guidelines, and codes of practice."

Jan 1, 2015

Following extensive trials on a 100 000 tpa Research and Development facility at Kwinana, Western Australia, Hismelt Corporation (wholly owned by Rio Tinto) are confident of the future commercial success of this technology. The Hlsmelt process uses iron ore fines and non-coking coals to produce molten pig iron suitable for feeding to BOF and EAF steelmaking vessels. The unique process configuration combines direct injection of raw materials into the molten iron bath, high rates of metal and slag mixing, and effective post-combustion of the bath gases to achieve efficient coal utilisation. This is the key to the strong economic performance of the process.

Jan 1, 1999

By A. A. Debrah

Artisanal and small-scale mining (ASM) plays a fundamental role in the national and local economies of resource-rich countries in Africa. As such, more effort must be geared towards fostering this type of economic activity to sustain livelihoods in rural communities. Across Africa, efforts to operationalize ASM based on a sustainable development framework have been quite tedious and often ineffective. This is because most of these frameworks lacked context and an understanding of the continuum from the artisanal through small-scale and up to the junior miner, grouped under the general term ?ASM?. Driven by the need to contextualize some of the definitional issues in this niche sector, and gain a clearer understanding of their peculiar challenges, this paper aims to contribute to the debate on ASM by considering two of Africa?s resource-rich countries ? Ghana and South Africa. Since South Africa has made greater inroads in protecting the interests of small-scale miners, we thus draw comparisons from both countries? approach to ASM, outline the lessons learnt, and provide recommendations regarding the ways forward.

Jan 1, 2014