Search Documents

The discussion in this paper centres on examples of mining that are drawn mainly from the coal mining industry. The intention is to review the opportunities that exist for incorporating environmental planning into mining industry practice in New Zealand. The coal mining examples serve to make some general points which have some application for many types of mining.

Jan 1, 1981

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

By P M. Ashley, M Muller

Massive sulphide ZnPbCuAg deposits in the Halls Peak district of north-eastern NSW are of the submarine volcanogenic type. They occur as a number of small lenses enclosed in shale and epiclastic rocks, in association with felsic volcanics of early Permian age. The deposits crop out in steep terrain near the eastern edge of the New England plateau. Local relief of 700 m and slopes up to 50¦, coupled with an average annual rainfall of about 1000 mm has led to local severe land sliding in previously mined areas. Mining from the 1890s to the 1960s has also resulted in unconstrained drainage of heavy metal-bearing acid waters and physical dispersion of finer grained metalliferous sediments into the Chandler River. Waters emanating from the main landslide area, from underground workings and draining scattered unconfined stockpiles of massive sulphide ore have pH values of 3 to 4 and contain elevated contents of Zn, Cu, Pb, Cd and Fe. Chemical mobility of heavy metals into streams occurs under low pH conditions with Zn exhibiting the greatest dispersion. Increasing pH conditions downstream cause precipitation of Fe phases and coprecipitation of heavy metals. Physical dispersion of secondary metal-bearing minerals into the surrounding creeks results in wt% levels of Cu, Pb and Zn in the stream sediments thereby exceeding the regional background values by one to three orders of magnitude. Areas disturbed by mining are characterised by lack of vegetation, biomagnification of heavy metals into algae and lower plants, and partial recolonisation by metal-tolerant grass species (Snow Grass, Poa sieberana; Blady Grass, Lomandra longifolia). Rehabilitation measures will have to include landslide stabilisation, impervious sealing or removal of sulphidic materials, import of topsoil and revegetation by metal-tolerant, slow-growing native grass and shrub species.

Jan 1, 1995

By Brian Hart, Hong Zhong, Liuyin Xia, Kyle Douglas

"The application of hydroxamic acid as flotation collectors is fast becoming of significant interest for the selective flotation of oxide minerals along with upgrading oxidised based metal ores and minerals. In the hydroxamate molecule, both O and N atoms in the -CONHOH group are identified as coordination atoms in many complexes and their characteristic structure determines the strength of the chelation complex between the hydroxamate and metal ion. The chelating performance of hydroxamates with transition metals including Cu, Ni, Zn, Fe, Cr, Mn and Co, the alkaline-earth metals (Be, Ca) and heavy metal (Pb) has been studied. Cytec has developed and patented a range of alkyl hydroxamates as flotation collectors for oxidised base metal sulphides, metal oxide minerals and precious metals. This paper introduces two new structures of hydroxamate collectors (Cyclohexyl and 4-tert-butylbenzoyl hydroxamates) and evaluates their characteristics relative to alkyl and benzoyl hydroxamates. Laboratory small-scale flotation tests were conducted with ilmenite and wolframite. The use of 4-tert-butyl benzoyl hydroxamate resulted in a best flotation performance for ilmenite. A relatively low cyclohexyl hydroxamate dosage was required in the flotation of wolframite to obtain comparable results to the alkyl and benzoyl hydroxamates. It is also shown a significantly improved flotation performance with 4-tertbutyl benzoyl hydroxamate in the flotation of ilmenite plant ore in comparison to the oleic acid or fatty acid collectors typically used for ilmenite flotation.INTRODUCTIONHydroxamic acid has been reported as an effective collector in small-scale flotation tests for a wide variety of oxide minerals and ores including copper (Lee et al., 1998, Lee et al., 2009), iron (Quast, 2000), tin (Sreenivas and Padmanabhan, 2002; Wu and Zhu, 2006), tungsten (Marinakis and Kelsall, 1987; Xia et al.,2004), and rare earth metal minerals (Ren et al., 1997; Pradip and Fuerstenau, 1991; Assis et al., 1996; Pavez et al., 1996; Zheng et al., 1996; Chen et al.,2005).As part of our previous research project, a selected suite of hydroxamic acid collectors including fatty, aromatic and modified hydroxamates (naphthoyl, cyclohexyl, benzoyl, octyl, 4-tert-butyl benzoyl, salicylic hydroxamates) were tested in order to examine their potential for recovery and selectivity of rare earth minerals. In these tests it was shown that the flotation performance with the hydroxamate collectors was significantly better than the phosphoric acid collectors on no slimes removed samples (Brian, et al., 2014; Liuyin, et al., 2014 and unpublished internal technical reports). Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the phosphoric acid collectors. Recovery of both La and Ce was significantly better for the salicylic hydroxamate and that Nb, Y and Zr recovery were favoured by the octyl and benzoyl hydroxamates (Brian, et al., 2014; Liuyin, et al., 2014). Comparison among the hydroxamate collectors showed that the flotation and recovery performance of cyclohexyl (CHH) and 4-tert-butyl benzoyl (TBH) was not as good as the other hydroxamates for rare earth recovery."

Jan 1, 2015

By Unknown

More than 60 years ago Lakota (Sioux) Chief Henry Standing Bear asked Korczak Ziolkowski to create a monument of Crazy Horse in the sacred Black Hills. Today, you can see Standing Bear’s dream has grown into enormous reality. Crazy Horse Memorial, mankind’s largest mountain carving in progress, is being carved in the round and when completed will be 641 feet long and 563 feet high. Crazy Horse is only 17 miles from Mount Rushmore National Memorial, giving South Dakota unique boasting rights for having two extraordinary mountain carvings in such close proximity

Jan 1, 2009

By Both R. A, Daily B

The Patawarta Diapir, located in the northern Flinders Ranges (South Australia), has intruded into late Proterozoic Wilpena Group sedimentary rocks. The diapir contains disrupted blocks of a wide variety of rock types, most of which can be correlated with the Lower Callanna Beds of Willouran age, in a matrix of predominantly carbonate and siltstone breccia. Mafic rocks in the diapir appear to predate intrusion of the diapir. As with many other diapirs in the Flinders Ranges, copper mineralization is present in the diapir and occurs as narrow veins consisting essentially of carbonate with chalcopyrite and pyrite that formed after diapiric intrusion.Fluid inclusion studies demonstrate that the mineralizing fluid was a Na-Ca-K-Cl brine; probably derived by expulsion of interstitial water following emplacement of the diapir, with dissolution of evaporites within the Callanna Beds sediments and enrichment in copper by reaction with these sediments and associated basic igneous rocks. Mineral assemblages combined with fluid inclusion and geochemical data indicate a possible environment of vein formation of T ÿ 165°C, pH ÿ 4.3 ± 0.9 and log fO2 ÿ -47.3 ± 0.5. Sulphur isotope analyses indicate d34Sfluid ÿ 10 per mil, suggesting evaporites in the Proterozoic sediments as the major source of the sulphur but with some additional sulphur from an igneous source, possibly leached from the malic rocks of the diapir.

Jan 1, 1986

Jan 1, 2004

By I. C. L. Webster, G. E. Ray

"The magnetite-rich Heff Cu-Au skarn lies in the Quesnel Terrane of south-central British Columbia, approximately 26 km northeast of Kamloops. The skarn formed close to the northern margin of the Heffley Creek pluton, and is hosted by Carnian (Late Triassic) Nicola Group limestone. The Late Triassic pluton (208.1 ± 6.1 Ma, U-Pb zircon) is a composite body of alkaline affinity that includes dioritic, gabbroic, and magnetite-rich clinopyroxene ± olivine ultramafic phases.The skarn has been discontinuously traced along strike for more than 1 km, and individual skarn layers are up to 40 m thick. The most common non-opaque minerals are garnet, clinopyroxene, and carbonate, with lesser epidote, biotite, amphibole, and chlorite. Apatite locally forms more than 3 vol.% of the rock. Compositionally the garnet is a low Mn grandite averaging Pyr3-Grs41-Adr56 mol.%.Mineralization consists of lenses, up to 10 m thick, containing massive low Ti-V magnetite (avg. 0.03 wt.% TiO2 and 0.01 wt.% V2O3). Magnetite is associated with up to 20 vol.% pyrrhotite, lesser pyrite, and trace chalcopyrite and gold. There is a moderate enrichment in rare earth elements with assays up to 570 ppm La and 490 ppm Ce. The Heffley Creek pluton belongs to a suite of Late Triassic-Early Jurassic alkalic and Fe-rich intrusions that are widely developed throughout the Quesnel Terrane. Some host Cu-Au porphyry mineralization, but less commonly they are associated with magnetite-apatite veins such as at the Glen Iron mine and Magnet occurrence, or with magnetite-rich Cu-Au skarns such as the Heff occurrence.Although abundant low Ti magnetite is present in the Heff skarn, it does not appear to represent iron oxide copper- gold (IOCG) type mineralization. Microprobe analyses completed during this study show that low Ti magnetite is not a unique feature of IOCG deposits, but also characterizes some other types of hydrothermal mineralization. In British Columbia these include some alkalic porphyry-related magnetite-apatite veins in the Quesnel Terrane, as well as the well-known Wrangellia-hosted Fe skarn deposits. Thus, low Ti magnetite appears to be a common signature of many magmatic hydrothermal deposits in contrast to the high Ti primary magnetite found in most igneous rocks."

Jan 1, 2007

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By Ilpo O. Auranen

Background: Mines of today are moving ever increasing tonnages of rock. The new ore bodies tend be of lower grade and located deeper in the earth?s crust. The industry?s focus to overcome this ?deeper but poorer? ore problem has traditionally been to lower the costs by increasing the scale of mining. This has resulted in an ever increasing size of mining equipment like drills, loading shovels, dump trucks. The main focus has been in reducing the cost per ton of mining. This cost focus has often resulted in increased waste rock dilution and more ore losses. From costs to value: Waste rock dilution means waste rock in the concentrator feed. It?s value in open pit mining is equal to the value of ore it replaces. In underground mining, waste rock dilution?s value is equal to the value of ore it replaces added to the costs of mining it. It is commonly accepted that waste rock dilution in open pit mining ranges between 5 and 20% and in underground mining between 5 and 40 % . In a typical large open pit mine ore value is from 20 to 60 USD per ton and mining costs are 1 to 3 USD per ton. One percentage point reduction in waste rock dilution represents savings corresponding to about 20% of total mining operation costs. The difficulty of reducing waste rock dilution comes from the complicated nature of the ores. Accurate ore waste-border detection has not been possible due to excessive costs. Core drilling combined with geochemical lab analysis is the most accurate method for locating ore waste borders. However, it is also expensive and time consuming, which is why it is often combined with somewhat lower cost methods like sampling drill cuttings from blasting drill holes or from reverse circulation drills and analyzing them in a laboratory. The main drawback with these methods, in addition high costs, lies in the sampling accuracy and in the quality control of the whole process when a large number of samples have to be handled manually. In every mine it is possible to halve waste rock dilution by using new on-line analysis technology .

Oct 1, 2009

Much interesting data on cemented carbides has been published over a period of years which, when classified and pieced together, gives a clear picture of this special branch of powder metallurgy. This is an attempt to present the essential information in an ordered account.THE HARD CARBIDES-THEIR PROPERTIES AND PREPARATIONThe so-called hard or refractory carbides are the carbides of a number of metals which are grouped together in the Periodic Classification. These metals are in groups IV, V and VI. They are titanium, vanadium, chromium, zirconium, niobium (columbium), molybdenum, hafnium, tantalum and tungsten. These carbides have attracted the attention of chemists because of their remarkable properties. They possess very high melting points, and are rather difficult to prepare in the pure state. Their outstanding propertyis their extreme hardness, which they share with certain other carbides, such as those of silicon and boron. In addition, these compounds possess distinctly metallic properties, such as lustre (in fused specimens) and high thermal conductivities.(l)t They are capable of forming alloys in two ways:1. With metals, particularly those of the iron group. 2. With each other (a case of solid solubility).The constitution of these substances is not that of ordinary salts, which obey the usual valency rules, but must be likened to that of certain intermetallic compounds. Actually they are "interstitial" compounds(2), that is, they are formed from the ordinary metallic lattice by the insertion of the relatively small carbon atoms in the interstices.. The energy required to fill the lattice completely is high, and this explains the difficulty often found in obtaining the exact stoicheiometric compound. Thus the carbides can have a range of composition, and can be considered as solutions of carbon in the respective metals.Physical Properties of the CarbidesThe hardness of these compounds is so great that it is difficult to compare the individual compounds on this basis. Becker(l) gives values on Moh's scale, which are not very accurate and are of no great value. Burden(3) has reproduced a diagram by Hatfield which indicates that the cemented carbides are between 1,400 and 2,000 on the Vickers diamond scale. However, the pure carbides are harder, tungsten carbide being about 2,200. Hoyt(4) describes a method of measuring hardness applicable to powdered specimenswhereby the powder is rubbed on a standard block of cemented tungsten carbide under standard conditions, and the rate of wear is determined. In...

Jan 1, 1942

By G. S. Hill, B. J. Huls

This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed the authors to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flowsheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit.

Jan 1, 2006

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By Liane J. Terrill

Rockbolt failures at the Waste Isolation Pilot Plant have been recorded since 1990 and are categorized in terms of mode of failure. The failures are evaluated in terms of physical location of installation within the mine, local excavation geometry and stratigraphy, proximity to other excavations or shafts, and excavation age. The database of failures has revealed discrete areas of the mine containing relatively large numbers of failures. The results of metallurgical analyses and standard rockbolt load testing have generally been in agreement with the in situ evaluations.

Jan 1, 1995

By C M. Wawryk, S L. Garwin, J D. Foden

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Batu Hijau porphyry Cu-Au deposit in south-western Sumbawa, Indonesia is an ideal natural laboratory to study the fractionation of iron isotopes in magmatic rocks that range in composition from basaltic andesite to tonalite. Intrusive rocks are associated with a porphyry system that contains well-preserved early hypogene copper mineralisation. We analysed pre-, syn- and post-mineralisation igneous intrusive rocks. We also separated magnetite, chalcopyrite and bornite from hypogene porphyry-style quartz veins, and measured the Fe-isotope ratios of samples by solution multi-collector ICP-MS. Iron isotopic composition of samples from the magmatic suite show an increasing d57Fe with increasing SiO2, supporting geochemical and textural evidence that the Batu Hijau Tonalites underwent closed system fractionation. Equilibrium and co-existing mineral textures allow the calculation of the following preliminary empirical mineral-mineral fractionation factors at 500°C for certain mineral pairs.Iron isotopes have the potential to provide geothermometric data to complement fluid inclusion data, especially where heating stages have operational limitations and where fluid boiling results in a wide variety of inclusion types that may make analysis difficult.CITATION:Wawryk, C M, Foden, J D and Garwin, S L, 2015. Iron isotope fractionation in magmatic-hydrothermal minerals – a porphyry copper case study from the Batu Hijau deposit, Sumbawa, Indonesia, in Proceedings PACRIM 2015 Congress, pp 389–396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By N. Simpson

Low carbon 11.5% chromium stainless steels are finding increasing use in industry as square or rectangular tubing material for the construction of structures by welding. During processing, resistively welded circular pipes are bent into square or rectangular shapes. During this process longitudinal cracks can sometimes develop atone of the inner corners of the section. An investigation has shown that the processing of round into square tubing with very sharp corners can cause excessive cold working at the inner corners of the squared tube. This, together with the high tensile residual stresses and a susceptible microstructure due to the presence of grain boundary carbides, can result in brittle cleavage cracking. Measures that can be used to reduce the problem are described.

Jan 1, 2003

This paper characterizes the copper cycle, that is, the flows of copper entering and leaving the African economy over a one-year period (1994). The major flows over the entire life-cycle of copper are examined; these include production (mining, milling and refining), fabrication of semi-products and manufacturing of finished products, use, and the waste management system. The results reveal that substantial amounts of copper (of order705 Gg/yr) are mined in Africa; of that amount, about 70 per cent is exported following processing, 18 per cent is utilized by African fabricators, and 12 per cent is discarded. The flows of copper products from African fabricators and product imports from other continents exceed product discards by large amounts. This difference, about 0.25 kg Cu/capita/yr on average, is added to in-use stock, largely as wire, plumbing tube, and in electronics. Some 65 per cent of the copper in discard flows is contained in electrical and electronic products, where it is relatively easy to collect and process for reuse. About a third of the copper discard flows known is recycled. The actual percentage is almost certainly higher because of informal (and unrecorded) recycling. Much of the remaining discarded copper is diluted into the municipal waste stream, where recovery and recycling are probably not economically justified. Keywords: material flow analysis, resource management, material budgets, copper, stocks and flows, systems analysis, Africa, developing country

Jan 1, 2003

By C. A. Horne

"The transportation of mineral solids in the form of slurry is a subject most of us are associated with and, in fact, live with on a daily basis. The design parameters of slurry systems and most important the prime movers or cent¬rifugal pumps, are frequent and often controversial subjects due to the lack of practical guidelines which, if known and followed, can increase both reli¬ability and service life of the equipment.In this talk, emphasis has been placed on the practical side or rule-of-thumb approach to applications which, in turn, has been related to successful field results. The theoretical content and complex design criteria associated with actual equipment design has consequently been held to a minimum in the following discussions.I. BASIC SLURRY PUMP DESIGN CONSIDERATIONSFirst, to better understand how a centrifugal pump performs work, a basic description of the operating principles are in order.A. Operation In a pump, mechanical energy is transformed into pressure energyby virtue of the centrifugal force exerted by the rotating impeller. The liquid is discharged by centrifugal force at a velocity required to generate a given head and the volute collects the liquid so useful work can be done by the conversion of kinetic energy to pressure energy."

Jan 1, 1976

By G. G. Barbante

The oxidation behaviour of selenide matte with a substantial Cu content and low Ag differs significantly from that of high-Ag matte. Low-Ag selenide mattes display a large oxygen solubility and the upper boundary of the miscibility gap in the Ag-Cu-Se-O system is depressed to quite low Se contents. As a result, the formation of Ag metal is considerably delayed. The oxidised selenide matte, low in Se and with a relatively high oxygen content, has previously been termed oxymelt. With further oxidation, its composition enters the misciblity gap and crude Ag is formed. The sodium silicate slag captures very little of the SeO2 and the dissolved Ag2O(s) content of the slag is relatively small, with a Raoultian activity coefficient of 0.57. This value was found to be independent of the slag's Cu2O content

Jun 19, 1905