Search Documents

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By M. A. Trevits, T. A. Gray, L. M. Crayne, P. Glogowski

Mine seals can he remotely constructed in underground coal mines through vertical boreholes when direct access to a fire is impossible or considered to he too dangerous. This method has great merit because the boreholes can be drilled to specific mine areas, and the seals can be positioned close to a fire zone. The technology however can be largely ineffective if the constructed seals do not provide of effective barriers to airflow or if they cannot he used to impound water and other inert materials. Unfortunately, no viable alternatives exists to sealing the entire mine to the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL). Under this effort. Howard Concrete Pumping Company and GAI Consultants Inc. have joined forces to evaluate a potentially significant improvement to the current state of the art. This paper covers the development o f novel technology or rewrote mine seal construction, the evaluation of rite materials used, the construction practice and the Fellow-up testing.

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

The following data are put together to assist those who are responsible for ordering stores for mines and works. When making out a list of mine stores for a new plant, one can hardly be expected to remember everything, still it is all the more important that articles should not be forgotten, should the mine be situated in an out of the way place, where the manager has to look several weeks ahead. A man who has been accustomed to buy stores on a small scale, from local merchants, where he could pick out personally what he wanted, may suddenly find himself in a place where he has to order wholesale quantities or make out store lists to send contractors for quotations. As it is of course cheaper to purchase stores by the hundredweight, coil, barrel, etc as the case may be, in which they are made up, than to break such a parcel, the way in which the materials are placed on the market is mentioned, so that those who don't know may take full advantage of wholesale terms. The most frequent sizes and brands employed in connection with Australian mining are also mentioned. It would be useless to enumerate all sizes made by the trade, as many would be of no value for our purpose; still I have put down what will serve as a reminder to the manager to mention what size he requires when giving an order, such as the diameter of dynamite cartridges a slight neglect of this sort has often caused serious delay. By mentioning certain brands I do not wish to recommend them in preference to others inadvertently omitted they are simply mentioned as some of those frequently met with.

Disseminated gold mineralization in the Vunda River area 12 km SE of Lautoka in Viti Levu occurs sporadically in shoshonite volcanics within an alteration area of some 6 km2. No definite intrusions have yet been located though possible intrusions occur toward the centre and on the eastern margin of the area. The nature and distribution of alteration suggests the presence of a co-magmatic mineralizing stock just below the surface.The gold occurs within close spaced fractures and occasionally around the c1asts of breccia and agglomerate.Various types of alteration compatible with porphyry mineralization occur, but to date show no zoning or defined correlation with incidence of gold which occurs in various alteration facies.It is suggested that the gold and trace copper mineralization at Vunda arises from the sub-volcanic intrusive phase (monzonite) of the Sambeto shoshonite (5 m.y.) and is part of an E-W zone of porphyry-type mineralizationtrending easterly to the Kingston porphyry copper deposit at Navilawa.There is a close similarity between the Vunda mineralization and some of the porphyry deposits of alkali affinity in British Columbia, Canada.

Jan 1, 1978

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010

By M. Hopf, E. Rossouw

Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able to consistently identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed). Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa.

Jan 1, 2006

By Joseph H. Bilbrey

COBALT is a silvery gray metal which closely resembles nickel in appearance and properties although it is somewhat harder and more brittle. It is rather widely disseminated and is estimated to make up about 0.001 percent of the earth's crust as compared to 0.020 percent for nickel. Cobalt, one of the four ferromagnetic elements, is used for many magnetic applications. It is oxidation resistant, a property which when coupled with its moderately high melting point of 1,495° C., makes it useful in high-temperature applications. Although cobalt had been used by man as a coloring agent for glass and other ceramic products for 4,000 years, it was not isolated as a metal until 1742 and not established as an element until some 40 years later. Early in the 20th century, cobalt began to be used in alloys, and soon these applications displaced ceramics as the major consumer of cobalt. The use of cobalt in alloys gave considerable stimulus to production, and the world output of cobalt increased rapidly, rising from 400 tons in 1920 to 1,400 tons in 1930 and 5,500 tons in 1940. With the advent of the jet plane in the mid 1940's and the consequent increased need for cobalt-bearing high-temperature alloys, cobalt production again increased, reaching 7,900 tons in 1950. The increased demand for cobalt during the Korean war coupled with a large demand for stockpiling caused world production to more than double within the next 10 years, reaching a peak of 17,300 tons in 1959.

Jan 1, 1962

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

On-stream determination of xanthate concentrations can be made by photometric measurements at 313 nm.A simple double-beam instrument was developed for this purpose. A mercury lamp is used as the light source and a composite filter of UGll glass and chromate solution is used to isolate the required spectral region. The light beam is split into two components of approximately equal intensity. One component is passed through a reference cell containing water to a photo detector; the other component is passed through the xanthate solution to a second photo detector. The reference signal controls amplifier gain to eliminate effects of lamp intensity changes and the amplified sample signal can then be used to measure xanthate concentration.Plant trials showed that provided a clear solution free of air bubbles was obtained from an on-stream filter, the instrument indicated the xanthate concentration and operated satisfactorily for long periods.

Jan 1, 1973

By Kevin Connor

There was little change during 1988 in the production of minerals in Burundi. The Government of Burundi, which banned all commercial mining operations in the country in 1979, lifted the ban on mining of alluvial gold deposits and started a program of small-scale artisan gold mining in October. Along with the legal mining of gold, licensed gold trading counters were established. Other mineral commodities produced were kaolin clay, lime, and peat. In compliance with the Government ban, the only mineral wealth exploited for commercial sale and export was alluvial gold. Through financial assistance from the International Bank for Reconstruction and Development (World Bank) and the United Nations Development Program (UNDP), a study to inventory the country's mineral resources continued throughout the year. As part of this study, during the year, a West German company undertook a drilling program to further outline the nickel reserves of the Musongati area in central Burundi. Results of the work as of yearend were disappointing, with only 12 million tons of ore identified with better than 2% nickel content proven. Investigations also continued during the year regarding the centrally located deposits of vanadium-bearing titaniferous magnetite. A Norwegian company contracted to prepare a prefeasibility study for developing the deposit. The British Sulphur Corp. Ltd. was nearing completion of its $1.2 million2 study of the phosphatic limestone deposit at Matongo-Bandaga at yearend. Ore reserves of about 17 million tons grading 11% phosphorus pentoxide (P2O3) had been identified. The phosphate zone overlies a carbonatite rock, which could provide the basis for a cement industry. Additional drilling was planned for 1984. Exploration for gold was underway in 19S3 in northern Burundi through UNDP funding. Several primary deposits of shallow semimassive sulfides with gold values ranging from traces to 11 grams per ton had been discovered. With assistance from the Federal Republic of Germany, bastnasite reserves of 5,400 tons, with associated high europium oxide and cerium content, were verified, and the prospects for finding

Jan 1, 1985

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991

By Burns W. G, Muceniekas E, Whitcher I. G, Hughes F. E

No iron ore deposits were reported before 1961 from the Hamersley Ranges, Western Australia, although low-grade bedded iron formations, associated with ferruginous jaspers and cherts, were known to occur in the local Nullagine Series of Precambrian age.In January-March 1961 preliminary investigations in the area drained by the Turner River, Duck Creek and Serpentine Creek revealed the presence of over 1000 million tons of dense botryoidal or pisolitic limonite, forming flat-lying orebodies with 50-57 per cent iron.Large bedded hematitic orebodies were also discovered in the same area in August-October 1961. These have a porous, biscuity texture and an iron content of 60-61 per cent. They occur at a welldefined stratigraphic level (Brockman Iron Formation), normally in synclines where they have been upgraded by circulating meteoric waters during an old cycle erosion.In 1962 systematic geological studies and mapping, together with sampling and scout drilling, indicated larger reserves of biscuity hematitic ore and led to the discovery of massive hematite deposits at Mt. Tom Price. These were extensively drilled in 1963, proving the persistence of' high-grade mineralisation to a depth of 200 ft and over.To date the total indicated reserves of the Hamersley deposits, within the area held by Hamersley Iron Pty. Limited, are of the order of 4960 million tons and thus rank among the more important of the world. The reserves are composed of 600 million tons of bedded dense hematite ore with 64-66 per cent iron, 2900 million tons of bedded biscuity hematite-limonite with 60-61 per cent iron, 1360 million tons of limonite (goethite) ranging in grade from 50 to 57 per cent, and 100 million tons of canga (conglomerate) iron ore containing 53-63 per cent iron. In all cases harmful impurities are comparatively low.

Jan 1, 1964

By James S. Graham

Foundation pile driving hammers used in New York City in the past 100 years have been drop, steam, compressed air, diesel, and hydraulic. In 1992, the first hydraulic hammer in the New York City area was purchased by Norwalk Marine Contractors, Inc. from Junttan in Finland. It was bought because of its variable energy and ease of mobilization, not because of its higher transferred energy. Heller and Johnsen engineers instrumented hydraulic hammers on nine jobs. The measured transferred energy for the nine jobs was found to average approximately 80 percent. There is no clear consensus regarding the reasons for the hydraulic hammer being more efficient in delivering energy to the pile as compared to single-acting steam/air impact hammers. To minimize pile damage during installation, and to minimize footage overruns, an up-to-date version of the wave equation software that includes an efficiency value of 0.95 for hydraulic hammers is now used.

Jan 1, 2000

OBJECTIVES ??REDUCE OPERATING COSTS ??INCREASE LIFE COMPONENTS ??EXTEND LIFE of THE DOZER ??REDUCE MAINTENANCE COST ??REDUCE DOWNTIME ??IMPROVE DURABILITY & RELIABILITY ??IMPROVE BOLD JOINTS PREFORMENCE ??IMPROVE SAFETY

May 1, 2004

By McLean E. J

Background The resources of the Gippsland Basin include not only the coal and oil for which it is well known, but also the tourism resource and the quality of life which it offers its residents and visitors. To manage this group of resources requires an understanding and ability to predict the consequences of possible developments. The water of the streams and estuaries as a key component as it is both a resource and the means for transporting wastes from one area to another. To aid in the resource planning process there is a need for models of the estuarine hydraulic processes. This paper describes an appropriate modelling technique. Resource use conflicts may arise from developments in the catchment upstream of the estuarine reach. For example the diversion of water for domestic and industrial use will change the velocity and salinity structure of the downstream estuary. In turn these changes will affect sediment distribution and deposition patterns and may impose stress on the biological communities and ultimately on the fisheries resources and water quality. The manager of an estuarine system may have expertise in ecology, hydraulics or another of the specialist disciplines involved, but commonly will not. The manager will identify needs for resource and development and the broad options required to satisfy them. The manager will use these studies as the basis for his/her selection of the option for execution. Thus a model for'use by the manager of an estuarine system must have the following properties: (i) The model must be sufficiently accurate to throw up all the likely options. (ii) The model must be capable of being run by the manager, interactively, to answer `what if' questions. This requirement implies a simple code andhardware limited to a personal computer or possibly a desk top work station. (iii) The model must be robust so that unrealistic input oes not generate apparently useful output, and no output is generated for cases where the model is not designed to give results. (iv) The model must be capable of being used as part of a modelling system comprising models of all the geographic and demographic components

Jan 1, 1992

The Bureau of Mines annually publishes statistical data reflecting technological trends in the minerals industry (metals and nonmetals except fuels). This report outlines recent developments and trends and the technology outlook for mining practices and metallurgical processing based on a review of the minerals industry during the past 2 years. A historical statistical series which indicates trends in the minerals industry has been extended with 1970 data. In addition, data are given from a 5-year Bureau of Mines cyclic canvass of froth flotation plants. Data for 1970 are compared with those of 1960 and 1965.

Jan 1, 1972

By Nicholas Adrian Barcza

"What affects and influences one’s perspective of the mining and metallurgical industries?One’s perspective of the industry we work in changes over time as a function of our experience as well as from the interaction we have with colleagues locally and probably even more so with those internationally. Furthermore, the ever-changing environment continues to impact the context in which one sees things. Living mostly in South Africa through its changes in the past fi fty years but also having the opportunity to travel extensively and work on projects abroad adds an invaluable richness to this more global perspective. One of the greatest challenges is how best to use this experience to endeavour to support the many potential opportunities in southern as well as sub-Saharan Africa. However, one has also to face the realities of how the best interests of the country and its peoples are sadly often not well served for various unfortunate reasons. Investment, education, regional stability, and good governance are some of the most critical considerations for the prosperity and survival of the region.The mining and metallurgical industry in southern and sub-Saharan Africa changed significantly during the post-colonial and apartheid eras as a result of global and regional developments that have impacted the ownership of businesses, the technologies used, and products produced in a manner that was not envisaged even fi fty years ago. Southern Africa’s mining and metallurgical industry has progressed from one based mostly on diamonds and gold in the late 19th century to a much more diverse one that involves the production of a variety of other precious, base, and ferrous metals and minerals as well as coal and industrial minerals. The infrastructure and manufacturing capacity was largely developed to meet the needs of this industry during its growth phases, but even though the dynamics have changed there is still a need for more efficient and effective support systems in the region."

Jul 1, 2019