Search Documents

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By B. W. J. van Rensburg, M. J. Schmidt

Bulk materials handling systems are extensively used in the mining and minerals industry, where a fairly high incidence of structural failure is experienced, notwithstanding design compliance with appropriate standards. A number of case studies are explored to demonstrate how insufficient controls or protection systems have contributed to structural failures on mobile bulk handling equipment. The importance of design integration across engineering disciplines is highlighted. The revision of ISO 5049-1 (1994) is proposed to provide specific rules and guidelines pertaining to machine protection systems. It is further recommended that the structural design engineer of the original equipment manufacturer(OEM) fulfils a more prominent role during the final acceptance and handover of mobile bulk handling equipment, with specific reference to protection systems.

Jan 1, 2015

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Due to the difficulties of ventilating large opening stone mines, the effective dilution of diesel particulate matter and noxious gases has often been problematic. Since stone mines have large openings that develop low air resistances, and propeller fans are designed for low pressure-high volume applications, main mine propeller fans may be a feasible option for ventilating underground stone mines. This paper describes the results of a case study where researchers from the National Institute for Occupational Safety and Health have demonstrated that significant increases in total mine airflow can be achieved and the ventilation improved in a large-opening stone mine by replacing an axial-vane mine fan with two 12-ft diameter propeller fans and adding a line of stoppings. In this study, the use of the propeller fans more than doubled the air quantity from 300,000 cfm to 750,000 cfm, while operating at 50 horsepower less than the original axial-vane fan.

By Paul C. Schmall, Lucian P. Spiteri, Arthur B. Corwin

Moving groundwater is generally recognized as the most adversarial condition for ground freezing. Moving groundwater can occur due to natural or man-induced groundwater flow, but either way may result in freeze formation difficulties. History has shown that if the condition goes undetected, catastrophic failure of the frozen shaft or excavation can occur. The success of ground freezing under potentially flowing groundwater conditions depends on an evaluation of the likelihood for this condition; an accurate and early diagnosis, with a careful evaluation of freeze pipe temperatures and piezometer water levels; and timely reaction to mitigate the possible delays. Successful remedial measures have included the reduction of ground permeability by modifying the soil properties between the freeze pipes with various kinds of grouting, or increasing the freezing effect by adding freeze pipes and/or the use of liquid nitrogen as the freezing agent.

Jan 1, 2007

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By M. Ksiazek

Keywords: Thermal conductivity, thermal diffusivity, flash method, specific heat capacity, manganese ore Manganese ferro-alloys manufacturing involves a combination of quality raw materials and an energy source to produce high-quality products with low energy consumption. The thermal properties of manganese raw materials such as ores, sinters, and briquettes, are among the many factors that determine the amount of energy needed for processing. Thermal expansion, thermal diffusivity, conductivity, and apparent specific heat capacity of solid samples and compacted powder samples of manganese ores were examined from room temperature to 1000 °C. The effect of porosity (of the materials used) on the thermal properties was also investigated. The laser flash method and a pushrod dilatometer were used.

Jan 1, 2011

By Dean Brox, Jason Morrison, Peter Procter

The Galore Creek Mine project is one of the newest major mining projects underdevelopment in Canada. The project is located in a very remote area of northwester British Columbia and is being developed by Nova Gold Resources of Vancouver. The mine project comprises one of the largest and highest grade undeveloped porphyry-related gold-silver-copper deposits in North America. In order to access the mine site anew 120 km road is planned to be constructed including a 4.4 km mine access road tunnel. Glaciers with heavy snow pack cover approximately two-thirds of the tunnel alignment with a maximum cover of 1,200 m. The size of the access road tunnel is about 50 m2 and has been designed as a large single lane road tunnel to accommodate the transport of large size mining equipment for mine start up and ongoing operations. The rock conditions along the tunnel alignment comprise very strong volcanic rocks. Key services for mining operations will be incorporated into the tunnel comprising diesel and power as well as the concentrate pipeline. Structural portal canopies have been incorporated into the tunnel design due to the risk of rockfalls and avalanches in the portal areas. The mine access road tunnel is a significant and critical-path component to the overall project to provide vehicular access to allow construction of the mine site. In order to meet the expected mine start up date the construction of the tunnel works are to commence prior to any other works at the mine site and will be constructed entirely by helicopter support. Geotechnical investigations commenced in the summer of 2006 with the removal of the overburden materials at the portals to assess bedrock conditions. Tunnel construction from both portals is expected to commence in the spring of 2007. The construction of the mine project is subject to and awaiting environmental approval in the spring of 2007. The mine access road tunnel will be the longest private road tunnel in North America. The key design and constructability issues for the mine access road tunnel project are presented and discussed.

Jan 1, 2007

The MineSight Schedule Optimizer (MSSO) is a new production scheduling tool developed by Mintec, Inc. using mixed integer linear programming (MILP) techniques. This tool was developed to solve the short- and medium-term schedule problems for surface and underground mining operations that involve multiple mining areas, multiple processes, multiple destinations and blending requirements. MSSO finds the optimum schedule in each period that achieves the objective while satisfying comprehensive product quality and quantity requirements as well as physical and technical constraints. Using the MineSight Planning Database (MSPD) as a central data hub, MSSO seamlessly works with MineSight 3-D (MS3D) block models and third-party data, MineSight Interactive Planner (MSIP), MineSight Haulage (MSHaulage) and MineSight Activity Planner (MSAP) to prepare data, formulate MILP models, calculate, report, fine-tune, save and visualize schedules. This paper presents the features and capabilities of MSSO. A case study is also given to demonstrate the applications of this new tool.

Jan 1, 2009

By F. E. Cash

"Explosions in bituminous coal mines are preventable. The combination of adequate ventilation, thorough rock-dusting, and water on the cutter bars of mining machines and of empty and loaded cars will certainly reduce the hazard to a minimum, if not remove it entirely. This is the attitude taken by the Woodward Iron Co. in lessening or removing the dust and gas explosion hazard from its Dolomite and Mulga mines.This report was made possible through the willingness of Frank H. Crockard, president of the Woodward Iron Co. to make records available and to authorize their publication for the benefit of the coal-mining industry.The compilation of these data and preparation of maps was facilitated by the cooperation of M. Heard, general superintendent of coal mines, J. B. Whatley, assistant general super-intendent of coal, and R. P. Whetmore, chief mining engineer.The Dolomite and Mulga mines are about 16 miles southwest of Birmingham, Jefferson County, Ala., on a company owned and operated railroad which connects ore mines, coal mines, coke ovens, and furnaces.In the Dolomite property there is a 30°, 860-foot, double-tracked slope for hoisting, three manway and air slopes and one air shaft, all in rock.At Mulga there is a 220-foot hoisting shaft, an air shaft and two manways, and material and air slopes, all in rock to the coal bed.The coal in both mines comes from the Pratt bed, which is the next coal above the Mary Lee bed in the Warrior Basin. The coal is horizontal or slightly undulating, with thickness varying from 36 to 72 inches and averaging 50 inches.The method of mining is essentially room-and-pillar with modifications for mechanized sections. The mines produced approximately 1,100,000 tons with 2,328,309 man-hours exposure n 1929 and 900,000 tons with 1,697,436 man-hours exposure in 1930.Through the work of the safety department the entire personnel in the coal mines, as well as in other departments, makes safety an essential part of efficient operation.Both mines are gassy; Dolomite produces about 334,000 cubic feet and Mulga about 919,000 cubic feet of methane every 24 hours.The ventilation maps, two of Dolomite mines (figs. 1 and 2) and one of Mulga (fig. 3) give as much of the details of ventilation as is practicable to put on maps of such scale. As will be seen from these maps there are two main ventilating fans in Dolomite mine and two in Mulga mine and the general direction of the air travel is indicated by long arrows to fan 1 and short arrows to fan 2 in each mine. Each fan has a gas or steam auxiliary drive and each mine has a complete fan and power unit ready for operation in emergency.In Dolomite, recently taken data show that fan 1 exhausts 82,000 cubic feet of air per minute at 3.2-inch water-gage pressure, with an analyzed methane content of 0.15 per cent, and fan 2 exhausts 115,500 cubic feet of air at 3.8-inch pressure and 0.10 per cent of methane. In addition, a Capell fan at No. 2 air shaft is a standby or emergency unit.In Mulga recently taken data show that fan 1 exhausts 83,000 cubic feet of air per minute at 3.0-inch pressure and 0.18 per cent of methane, and fan 3 exhaust 119,000 cubic feet of air per minute at 5.4 inch pressure and 0.35 per cent of methane. Fan 2 at No. 2 shaft is a standby or emergency unit for the Mulga mine.The ventilation is on a split system in both mines. All part split and total returns are measured, sampled, and analyzed weekly, requiring one man two days each week. During December, 1930, 77 samples were collected and analyzed in Mulga and 78 in Dolomite. Two weekly reports covering part of December, 1930, are given here so that they can be studied to show control of ventilation in the Dolomite and Mulga mines. In the event that a split sample shows more than 0.50 per cent of methane, immediate steps are taken to lower the explosive-gas content. The reports follow:"

Mar 1, 1932

By C. C. Miller, A. R. Belyea, C. H. Herty, E. B. Burkart

The removal of sulfur from steel has been studied by many investigators, but the quantitative relationships between the factors involved have not been determined. This is undoubtedly due to the number of variables encountered in practice, an attempt to study any one reaction or relation being affected by other reactions the relative importance of which cannot be estimated. The factors that affect the extent of removal of sulfur in the basic open-hearth process are generally considered to be: 1. Basicity of the slag: (a) Iron oxides in the slag; (b) carbon in the metal or carbide in the slag; (c) temperature. These factors affect the reactions: FeS + CaO = CaS + FeO FeS + CaO + C = CaS + CO + Fe. 2. Amount of sulfur in the gas. 3. Amount of manganese in the metal. The factors which affect the rate of removal of sulfur include, in addition to these: 4. Fluidity of the slag: (a) Normal changes in fluidity with temperature; (b) changes in fluidity because of the addition of special reagents such as fluorspar. 5. Agitation of the bath. Within the past two years, two papers have been presented dealing with the influence of sulfur in the gas on slag and metal. Nead' has shown that if a gas high in sulfur be used for heating, the metal and slag will absorb sulfur. Whitely2 concluded from his experiments that if a

Jan 1, 1925

By Lise Chénard

El presente texto señala los lineamientos del proyecto REFORMIN, así como su repercusión en la dinámica de promoción de la industria minera. REFORMIN surge en el 2001 como un proyecto bilateral entre Canadá y Bolivia, cuyo financiamiento proviene de la Agencia Canadiense de Desarrollo Internacional (ACDI). Su finalidad es apoyar al Viceministerio de Minas, facilitándole el acceso a la pericia canadiense para lograr una gestión más sana y eficaz de los recursos minerales del país. Para ello, se basa en los principios fundamentales tales como: mejora de la gestión del medioambiente minero, apoyo a la prevención y gestión de conflictos sociales en las comunidades mineras, a los mineros artesanales y a la promoción de los recursos minerales del país, -en tanto benefician al desarrollo de la industria minera en un contexto de mercado globalizado.

Apr 22, 2003

Hydrogen and carbon monoxide reduction data were obtained on pelletized materials of the type currently being prepared commercially in Australia.Pellets, approximately 1 cm diameter, made from Deepdale, Iron Prince, and Mt. Newman iron ore were reduced by hydrogen over the temperature range 500°-900°C and the reduced pellets were examined by thermogravimetric, microscopic, electron probe, and x-ray techniques. After an initial time delay it was found that up to 95 per cent reduction the data could be described by a porous model where gaseous diffusion through the solid is rate controlling. Independent measurements of effective diffusivity supported the values obtained from the reduction data. Above 95 per cent reduction the rate decreased markedly due to the formation of retained wustite or fayalite.Comparison with reduction by carbon monoxide over the temperature range 750°-900°C showed that the rate of reduction was approximately five times slower than for reduction by hydrogen.The rate of reduction was found to be a function of the initial properties of the pellets which may account for the widely conflicting results that have been obtained with previous investigations on porous pellets.

Jan 1, 1971

By Hongjie Yang

The No. 10 metro line of Shanghai city is 36 kilometers in length and will pass through the operating airport runway by using tunnel boring machine with earth pres-sure balance mode. Although there are examples through world that tunnels pass through airport runway and tunnelling underground is not a difficult undertaking technically, there is rare experience in China for the similar projects especially in Shanghai saturated soft soil region. Shanghai soft earth is famous for its high compressibility, high rate of water content, weakness in strength, large deformation and different characteristics in earth strata. Besides, the whole construction process will be under ultra-large airplane dynamic load on the surface ground over the tunnel, which increases the risks of construction process. This paper evaluates the feasibility of building the metro tunnel under such an extremely serious condition, especially the subsidence of ground surface caused by advancing of tunnel boring machine, which also is the most important control target for the safe operating of the runway. Furthermore, this paper discusses the effective measures to keep the settlements in the permissible level during the whole working period for the tunnel from aspects of plan, design and construction.

By J. Wills

The use of drilling rigs to increasingly mechanize stope drilling has been acknowledged as important for the S.A. mining industry in it ís efforts to tackle the challenges of low productivity, AIDS and an ageing driller workforce. The spin-offs of increased safety, cost-effectiveness and better mining performance provide advantages to all?from the driller to the shareholder. However, implementation or product rollout has varied from outright success to dismal failure. A study of various cases by Novatek and Anglogold TDS showed clear reasons for these differences. Whereas the successes were characterized by clear objectives, accountability, user buy-in, a commitment to make the technology work and no-nonsense reporting, these were typically absent in failed implementations. The attitude at unsuccessful mines was to ?trial? the equipment?even subconsciously, a ?trial? is a test where failure becomes an acceptable outcome. During the study it became clear that mining management are not adequately trained to manage the often-tricky rollout process. They are often also not empowered or clearly mandated to deal with the organizational, human and technical issues that must dovetail to create a success. The output of the study was to develop a basic rollout process that could be used to formally manage the implementation of new drilling technology. Creating an alignment between the mine, workforce and supplier promotes a win-win situation that will not otherwise spontaneously arise.

Jan 1, 2002

By M. Bustillo, S. Ordonez

"Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The Mississippi Valley-type deposits occur in massive, homogeneous dolostones from which diagenesis has obliterated all primary sedimentary structures. The mineralisation forms irregular, lens-shaped stratabound bodies, mostly in the lower part of the dolostones. They are composed exclusively of sphalerite, galena, pyrite, marcasite and barite, with white sparry dolomite a common cementing phase. Mineral zoning can be recognised from pyrite and marcasite in the east to barite in the west. Sphalerite, the most common sulphide, occurs basically as colloform and banded crusts and galena as isolated cubic or skeletal crystals, mainly in the centre of the banded botryoidal sphalerite. The combined observations of the deposits' geology, geochemistry and ore petrology suggest a three-stage genetic model: carbonate sedimentation in a shallow-water environment; dolomitisation, probably after compaction, by fluids of connate origin and lateral evolution; and mineralisation by migrating solutions, perhaps related to oil-field brines, that originated in deep zones of the basin during diagenesis of the basinal mudrocks in the NE"

Apr 1, 1995

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.

By Mark Van Dyke, Ted Klemetti, Joe Wickline

"The identification and mitigation of adverse geologic conditions are critical to the safety and productivity of underground coal mining operations. To anticipate and mitigate adverse geologic conditions, a formal method to evaluate geotechnical factors must be established. Each mine is unique and has its own separate approach for defining what an adverse geological condition consists of. The collection of geologic data is a first critical step to creating a geological database to map these hazards efficiently and effectively. Many considerations must be taken into account, such as lithology of immediate roof and floor strata, seam height, gas and oil wells, faults, depressions in the mine floor (water) and increases in floor elevation (gas), overburden, streams and horizontal stress directions, amongst many other factors.Once geologic data is collected, it can be refined and integrated into a database that can be used to develop maps showing the trend, orientation, and extent of the adverse geological conditions. This information, delivered in a timely manner, allows mining personnel to be proactive in mine planning and support implementations, ultimately reducing the impacts of these features. This paper covers geologic exploratory methods, data organization, and the value of collecting and interpreting geologic information in coal mines to enhance safety and production.The implementation of the methods described above have been proven effective in predicting and mitigating adverse geologic conditions in underground coal mining. Consistent re-evaluation of data collection methods, geologic interpretations, mapping procedures, and communication techniques ensures continuous improvement in the accuracy of predictions and mitigation of adverse geologic conditions. Providing a concise record of the work previously done to track geologic conditions at a mine will allow for the smoothest transition during employee turnover and transitions. With refinements and standardization of data collection methods, such as those described in this paper, along with improvement in technology, the evaluation of adverse geologic conditions will evolve and continue to improve the safety and productivity of underground coal mining."

Jan 1, 2019

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

The Electricity Generating Authority of Thailand (EGAT) Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 Mt of lignite annually to generate 2400 MW of electricity. The surface mine pit covers is 4 km by 7 km with mining depths ranging up to 260 m. A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope occur often due to the existence weak planes such as faults and bedding, and the weak mechanical properties of the rocks. Hence, 200 m to 300 m boundaries of rock block including coal seams are left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope. Moreover, the mined coal seams are very thick and their thickness range from 15 to 30 m.This paper discusses the application of multi-slicing highwall mining system with stowing to this very thick coal seam left around large pit slopes by means of numerical analysis.

Dec 6, 2010

By S. C. Gouws

"SynopsisSustainable infrastructure development has long been identified as a key enabler for socio-economic growth and poverty reduction in societies globally. Twenty-one years into the young South African democracy, economic prospects are fragile and unemployment statistics are high. According to Trading Economics (2015) the GDP growth rate in South Africa averaged 3.07% from 1993 until 2015.Through the National Development Plan 2030, the government has responded by instituting the Presidential Infrastructure Coordinating Commission (PICC) to direct national growth and drive job creation by effecting a long-term infrastructure investment programme. The Commission is mandated by Cabinet to coordinate, integrate, and accelerate implementation of more than 150 individual social and economic infrastructure plans.In the civil infrastructure development sector, increased urbanization is compelling governments and the public sector to expand safe and reliable public amenities, but the availability of real estate for construction in congested cities is a challenge. Within the mining infrastructure construction industry safe, rapid, and efficient mine extraction strategies are imperative to realize increased production, business hurdle rates, and stakeholder expectations.Asset owners and stakeholders are obliged to consider advanced mechanized underground excavation and support technologies in order to present feasible solutions timeously. From an engineering design, procurement, and construction management (EPCM) perspective tunnelling technology and boring applications have a distinct advantage over conventional excavation techniques. These solutions may enhance commerce and transportation by expanding infrastructure in concentrations of national economic activity, providing crucial linkages with rural areas, between cities, and across international borders.This paper explores the contribution by mechanized tunnelling technology and boring applications applied in conjunction with digital and automation technologies compared with conventional methodologies. The technological expertise, combined with a paradigm shift in delivery of project objectives, will promote economic growth, aid recovery from the economic downturn, and improve social development."

Jan 1, 2015