Search Documents

By M. M. Fine

Small-scale laboratory mineral-dressing studies were made on a total of nine individual or composite samples of manganese-bearing material from the west-central Arkansas, or Mena, district. Of these, only three yielded concentrates that would probably be acceptable for purchases by the Federal Government fur the National Stockpile. Concentrates from some of the other properties, however, contained more than 40 percent Mn and might be merchantable to other purchasers of manganese ore. In most instances, a too-intimate association of manganese oxides and gangue is conducive to low grade, low recovery, or both, so that mechanical concentration processes do not promise much for this district.

Jan 1, 1956

Aase, Glenn D., (J'40) Jr. Met.. American Smelt. k Refin. Co., Selby, Calif. Abadie, Henry G., (J'43) Petr. Engr., Avenal, Calif. Abbott, Clarence E., (M'04) Civil Engr., V.P.. Tennessee Coal, Iron & R.R. Co., 1542 Brown Marx Bldg., Birmingham, Ala. Abel, Raymond L., (M'28) Chem. Engr., C.O., Pitts¬burgh Chem. Warfare Procurement Dist., American Bank Bldg., Pittsburgh. Pa. Abel, Walter D.. (M'32) Min. Engr., Supvr. Engr., R.F.C.Lee Angeles, Calif. Abele, Louis T., (M'31) Route No. 1, Adameville, Tenn. Abell, Leo M., (M'31) Mill Supt. & Met., Emperor Gold Min. Co. Ltd., Vatukoula, Fiji Is. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Kans. Abernathy, Jack H,, (M'40) Asst. Cenl. Supt. of Prod., Sunray Oil Co., 11th Floor, Philtower Bldg.. Tulsa 3. Okla. Abernethy, D. Carl, (M'44) Min. Engr. Rm. 3217, N. Int. Bldg., Washington, D. C.

Jan 1, 1944

By Zsuzsanna Zborovszky

Investigation of the discharge duration power and current relation required for ignition. The current and power amplitude-discharge time curve was found to flatten out over 3 ms. It is concluded that discharges having at least 3 ms power maximum are required for reliable testing of the ignition limit for resistive circuits. Investigation of the effect of molten cathode on the discharge duration and igniting ability of the discharge. The surface tension of the liquid metal causes a very fast separation and consequently a much shorter discharge duration than the solid electrode would have. The minimum discharge voltage effect overrides the effects of the temperature of electrode, material, or atmosphere. Investigation of the effect of different surface layers on the discharge duration. Oxides and sulfates were found to give significantly longer duration than the "clean" metal itself in most cases. The lowest ignition current was obtained with CdS04 coatings. Ignition was obtained with 0.7A at 30V, which is below the corresponding minimum igniting current obtained from the BASEEFA curve for circuits containing Cd, Zn or Mg.

Jan 1, 1977

By James M. Nishi, Lloyd Carpenter

Sixteen elements were determined spectrochemically in the general range of 3 to 1,000 ppm in high - purity columbium . Samples were converted thermally to Cb2 O , mixed with graphite and Ge02 , and excited for 15 seconds using a 15 - ampere dc arc . For the molybdenum determination , the oxidized samples were mixed with NaCl and Geo₂ and excited for 30 seconds . Spectra were recorded on photographic plates , and spectral line transmittance values were measured photometrically . Relative - intensity ratios of selected analytical and internal standard spectral lines were plotted against concentrations of standards to form curves from which concentrations of impurities were read . Average precision of the method was 11.2 percent relative standard deviation .

Jan 1, 1964

By Andrew W. Berg

The Bureau of Mines Mineral Industry Location System (MILS) is part of the computerized Minerals Availability System (MAS), a comprehensive data base of known mineral deposits. MILS, the location subsystem of MAS, has become widely used by the minerals industry and organizations with land-use planning and land management responsibilities. Information on more than 135,000 mineral locations and processing plants in the United States is contained in the data base. This information includes the name, location, mineral commodity, type of operation, bibliography, and cross-references for each property or prospect. Computer-drawn map overlays at various scales showing clustered MILS locations and computer printouts keyed to those overlays are available for inspection and reproduction at the Bureau's Field Operations Centers at Juneau, Alaska, Denver, Colo., Pittsburgh, Pa., and Spokane, Wash.

Jan 1, 1979

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 61 surface coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, ?A Guide for the Evaluation of Human Exposure to Whole Body Vibration.? The comparison showed that about ha]f of all surface coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only on the order of 15% would be expected to experience vibration exceeding the exposure limit. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983

By R. L. Lincoln

The effects of adding from 1 to 50 atomic percent (a/o) to vanadium were investigated by the Bureau of Mines. Properties studied included as-cast and annealed hardness, microstructure, fabricability at room temperature and elevated temperature, tensile strength, electrical resistivity, and oxidation resistance at 625° and 800° 2. Additions of small amounts of hafnium resulted in lessened as-cast hardness, decreased electrical resistivity, impaired roll- ability, increased oxidation resistance, and greater tensile strength. Larger amount of hafnium caused greater as-cast hardness, increased electrical resistivity, further impaired rollability, continued increase in oxidation resistance, and lessened tensile strength. INTRODUCTION The purpose of this study was to determine the effect of hafnium additions on the properties of vanadium and to learn if this binary alloy had any special or unusual properties. This investigation is a part of a larger research project in which new and expanded uses of vanadium are being sought. Domes tic vanadium is found frequently in combination with uranium, and because of the demand for uranium as a nuclear fuel, there now exists a surplus of vanadium-bearing minerals and vanadium pentoxide as a byproduct of uranium production. Primary principles of conservation demand that greater use be made of this readily available surplus; finding suitable metals to alloy with vanadium to enhance its properties is one way to increase its utilization. This report is the result of an investigation of the effects on the properties of vanadium when hafnium is added in amounts from 1 to 50 a/o.

Jan 1, 1962

By J. Phillip Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

By P. J. Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

This report on the Venezuelan coal industry is the seventh in a series of studies on coal exporting countries requested by the House Appropriations Committee, The committee asked that the basic differences in mining costs for U.S, and foreign mines be identified, especially those costs incurred in complying with health, safety, and environmental regulations.1 Basic costs in extracting raw coal are analyzed in this report for surface operations, This report also provides a limited analysis of the relative market competitiveness of selected Venezuelan and U,S. steam coal mines in three electric utility markets: New England and the east coast of Florida in the United States, and western Europe. Although some Venezuelan coal has coking characteristics, all coal-producing regions of Venezuela sell coal in steam markets.

Jan 1, 1994

By Vitor Luiz Sordi, Gustavo Henrique Pelissari

O AISI201LN é um aço inoxidável austenítico com teor reduzido de Ni em relação aos tradicionais da série 300 e com adições de Mn e N como estabilizadores da austenita. Os aços da série 200 se propõem a substituir outros inoxidáveis em algumas aplicações com vantagem econômica pela redução do Ni, porém há pouca informação sobre o seu comportamento em temperaturas elevadas. Este trabalho avalia a resistência à tração do AISI 201LN na temperatura ambiente e na faixa de 500ºC a 800ºC e a resistência à fluência na temperatura de 700ºC. Observou-se que, comparado a outros inoxidáveis austeníticos, o material estudado tem resistência à tração comparável em temperatura ambiente e mantem boa relação ductilidade – resistência no intervalo de 500ºC a 800ºC. O aço AISI201LN apresentou desempenho em testes de fluência na temperatura de 700oC comparável ao de outros aços inoxidáveis austeníticos largamente utilizados para aplicações em altas temperatura, incentivando assim a ampliação dos estudos em outros intervalos de tensões e temperaturas.

Oct 21, 2019

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By Arne Landsberg

A study of the chlorination kinetics of germanium, silicon, iron, tungsten, molybdenum, columbium, and tantalum has been made to determine the effects of temperature, chlorine concentration, geometric surface area and gamma radiation. The reaction products were volatile at the temperatures used this making it possible to follow the reaction rates by weight loss of the solid. Chlorination rates of germanium, silicon, and iron were found to be directly proportional to chlorine concentration while the rates for tungsten, molybdenum, columbium, and tantalum were proportional to the 0.5 to 0.6 power of chlorine concentration. A good correlation of reaction rate and geometric surface areas was not obtained because the true surface area of the samples could not be measured. Intense gamma radiation had no effect on reaction rates. The Arrhenius activation energies determined over the temperatures used are as follows: Germanium, 27 kcal/mole (233°-241° C); silicon 33 kcaL/mole (375°-517° C); iron, cold rolled, 20 kcal/mGle (259°-325° C) annealed, 21 kcal/mole (293°-337° C); tungsten, 43 kcal/mole (617-776° C); molybdenum, 37 kcal/mole (445°-4910 C); columbium) 34 kcal/mole (229°?255° C); and tantalum, 29 kcal/mole (370°-449° C).

Jan 1, 1965

By John R. Anderson, Michael B. Bever

CARBON may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,1 the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. EARLIER DATA The solubility of carbon in molten pure copper is about 0.0001 pct at 1100 °C and 0.0004 pct at 1475°C.1 Various authors2-6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range 1217° to 1245°C. This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By Kazunori Matsushita, Masaru Sakakibara, Kenji Harada, Naotoshi Shinkawa, Mitsuo Nozu

The Sand Compaction Pile (SCP) method has been widely used as a typical countermeasure against liquefaction in Japan, and its effectiveness has been confirmed in many case histories of damages caused by the past large-scale earthquakes. A series of studies were conducted to evaluate the effectiveness of the compaction method and other factors, if any, in sustaining a seismic force that is greater than the assumed one and caused no damage. Based on the results of these studies, the Architectural Institute of Japan (AIJ) has indicated in its “Recommendations for Design of Ground Improvement for Building Foundations” published in 2006 that the liquefaction resistance ratio (tl/sz) of the composite ground, which consists of sand piles and surrounding compacted ground, is higher than the RL calculated by using the SPT N-values of the ground in-between the sand piles. In this paper, statistical analysis of safety factor against liquefaction, FL, was performed by using the SPT N-values of ground in Port Island and Rokko Island which were both fully reclaimed islands in Kobe city during the 1995 Hyogo-ken Nambu Earthquake (classified as intense shaking) and, together with the consideration of relative settlement, resulted in tl/sz of the composite ground being 1.5~2.5 times of tl/sz of the soil in-between piles after improvement. Furthermore, the liquefaction resistance curve of SCP-improved sites obtained from the relationship between SPT N-values and cyclic shear stress ratio during the 2011 off the Pacific Coast of Tohoku Earthquake, which was regarded as long-duration earthquake, was plotted to the left side of the curve originally proposed by Japan Road Association. Thus, the liquefaction resistance of the improved ground was found to be higher than that of the natural ground, even for the same SPT N-values, verifying the validity of the AIJ recommendation.

Jan 1, 2017

By Frank E. Cash

The Bureau of Mines in its safety work has for a number of years advocated and recommended the use of permissible portable electric cap lamps for use in all mines. In the course of time required for the evolution from an unsatisfactory to an efficient and safe light, but encouraging increase in their use has been experienced in Alabama. As early as 1916, small installations of these safer lamps were made or an experimental basis by several operating companies, and the first complete mine installation eras made at the Virginia mine of the Gulf States Steel Co., July 1, 1918. From the experiments in 1316 and the complete equipment of the first mine in 1918 gradual progress has been made until there are now 30 installations with 10 operating companies; as a result 20 mines have been put entirely and 5 partly on, closed lights, and 3 companies equip their engineering departments; two installations of closed lights are maintained by other companies for emergency use. One of the mines partly on the electric cap lamp is an ore mine - the only one in Alabama (and one of the very few in the United States) that uses closed lights. ACKNOWLEDGEMENTS The full cooperation of operating officials, lapmen, and lamp representatives was given in the collection of the data in this report, and is hereby acknowledged.

Jan 1, 1928

By Werner Wendt

La creciente industrialización y las necesidades de la escala mundial de energía eléctrica exigen el aprovechamiento de todos los recursos energéticos adecuados y disponibles. En ese sentido, el nivel actual logrado y la eficiencia de los equipos para las minas a cielo abierto y las instalaciones transportadoras y elevadoras ofrecen todas las condiciones necesarias para incrementar los rendimientos de explotación del lignito en las minas a cielo abierto yr extraer con economicidad el lignito desde grandes profundidades y suministrarlo al consumidor. Por ello, el presente texto señala la complejidad de los equipos utilizados en minería a cielo abierto para poder incrementar los rendimientos de explotación del lignito en las minas a cjelo abierto ·y para poder extraer con economicidad el lignito desde grandes profundidades y suministrarlo al consumidor.

Nov 1, 1978

By J. Hamilton Duffy

This is the first of, a series of papers describing dredging methods and costs in recovering sand and gravel from the beds of rivers throughout the United States and deals directly with the methods employed and costs obtained by the Ohio River Sand Co. near Louisville, Ky. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the collection of data and compilation of this report.

Jan 1, 1931

By R. R. Wells

As a part of the strategic mineral program, examining engineers of the Bureau of Mines collected samples several manganese properties in Colorado. As all of the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were required .to determine the amenability of the ores to concentration. Manganese in the form of impregnations in sedimentary beds is found in the Denver plains area a few miles east of the Rocky Mountain front. Deposits are reported to occur intermittently over a distance of more than 200 miles. The manganese oxides occur in beds of conglomerate or arkosic sand, generally accompanied by limonite. The Manganese and iron oxides,, however, usually are found in separate layers. Three samples were submitted for beneficiation tests, two samples from Buckley Field bombing Yang, Arapahoe County, and one from near Franktown, Douglas County.

Jan 1, 1952