Search Documents

By B. W. Gandrud

To say that the treatment and handling of the "fines" is the most difficult phase of coal preparation is probably an understatement of facts. It is the fine sizes from about 1/16-inch to 0 that are mainly responsible for the inescapable sludge and slurry problems at plants using wet methods of preparation. Sludge and slurry are a problem from the standpoints of both cleaning and dewatering. They cannot be cleaned satisfactorily by "gravity" methods, which are used so extensively on coarser Sizes, due to the fact that fine sizes, particularly from 65-mesh to 0, do not follow the same laws of settling as do the coarser sizes. Although fine sizes are cleaned more successfully on wet-wash tables than in jigs, even tables as usually operated in coal-preparation plants fail on sizes below 100-mesh. As to other phases of the, sludge and slurry problem, wet coal preparation plants are almost universally beset with troubles in connection with the recovery and dewatering of the fine sizes from about 14-or 20-mesh to 0. The sizes finer than 100-mesh further complicate the problems in a wet preparation plant by their tendency to stay in suspension and build up a troublesome load of solids in the circulating water. In order to prevent too much trouble from this source, it is, customary at most plants to bleed a fair-sized stream out of the circulating system continuously and replace it by addition of fresh make-up water. The slurry water withdrawn from the circuit is usually run to waste, in which case it carries with it a considerable amount of fine coal, thus increasing the "washer loss." Another evil results from wasted slurry water in that quite often it finds its way into creeks and larger streams, creating stream-pollution problems.

Jan 1, 1948

By R. Amata

"The Gakara Rare Earth deposit in Burundi (East Africa) is unique for its high grade (e.g., 54.3% TREO on average) and low uranium and thorium levels. The majority of the light rare earth (RE) elements in material from Gakara are contained within the familiar RE minerals bastnaesite and monazite. Extensive metallurgical test work was conducted by SGS Minerals Services on mineral samples collected from the Gakara deposit. Various whole ore hydrometallurgical processing routes were examined in a scoping level test program. Preliminary beneficiation testing was also conducted, though it was determined that only marginal upgrading would be achieved with significant RE losses. Thus a hydrometallurgical process on whole ore was developed to minimize the overall process complexity and achieve maximum RE recovery. Results from the test work will be presented, along with the selected base case flowsheet involving agitated atmospheric sulphation of the RE minerals, RE double sulphate precipitation, caustic conversion, redissolution, and carbonate precipitation. Following the base case flowsheet, a purified cerium free mixed RE carbonate with low levels of radioactive elements was produced.INTRODUCTIONRainbow Rare Earths Limited (Rainbow) is a mining company engaged in the exploration and development of the Gakara rare earth deposit in Burundi; Figure 1 shows the project location. The project is located in the Bujumbura Province and 45 km from the Burundi capital of Bujumbura. Notable for its exceedingly high in-situ grade – 54.3% on average total rare earth oxide (TREO), low uranium and thorium levels and familiar rare earth minerals, bastnaesite and monazite – Gakara is the world’s richest rare earth deposit. The project, a previously operating mine from 1948–1978, has a significant mineral inventory base, a long life of mine, well understood mineralogy, and robust economics. Rainbow is focused on bringing Gakara into production in the near term, ramping up to produce 5,000 t/y of a 54%+ TREO concentrate."

Jan 1, 2016

General economic conditions continued to improve in the second quarter of 1984 as real gross national product advanced at an annual rate of 7.5 percent (table 1). This followed an even larger first quarter annual rate increase of 10.1 percent. The slower second quarter growth was greeted as a sign that the economy is not over-heating. The signs of slowed growth in some sectors suggest that the recovery may continue well into 1985 without the inflation symptomatic of a rapid recovery. Most of the slowdown in growth was absorbed by business inventories, personal consumption of durable goods, and residential fixed investment. Business inventories grew by only 68 percent as much as in the first quarter, personal consumption for durable goods grew by 58 percent of the first quarter rate, and residential fixed investment slowed to only 44 percent of the first quarter growth. Sectors with accelerated growth in the second quarter included personal consumption of nondurable goods and of services, which increased at annual rates of 9.6 percent and 3.8 percent, respectively, and Federal purchases of goods and services, which increased at an annual rate of 47.9 percent.

Jan 1, 1984

By C. H. Riggs

This report describes the development, oil recovery, and potentialities of productive formations in the Hall-Gurney field, Russell County, Kans. It is presented as part of a general program to aid and promote increased recovery from petroleum reservoirs. The report is based on studies of well logs, drill cuttings, and oil-and water-production histories of individual wells and leases. The geological interpretations follow closely those in published literature with only slight local modifications. Oil and water analyses, made at a Bureau of Mines research center, were supplemented by many analyses obtained from oil-producing and service companies. The Hall-Gurney field, in south central Russell County, Kans., (fig. 1) was discovered in 1931 but was not developed extensively until 1941. By 1960 the rate of oil production from the field had declined to the extent that many wells were abandoned. In some areas natural productive forces have effected good recovery. However, in other areas inefficient waterflooding, both natural and accidental, has adversely affected recovery potentialities.

Jan 1, 1963

Abadilla, Quirico A. Catanawan, Tayabas, P I '20 Abbey, Robert Graham, District Mgr., The W. W. Sly Mfg. Co, 50 Church St, New York, N. Y. '21 Abbott,-A. N., Mines Supt, Mazapil Copper Co., Ltd .. Concepcion del Oro, Zac., Mexico. '23 Abbott, Clarence E., Mgr, Mines & Quarries, Tenn. Coal, Iron & R R Co. 1242 Brown Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div . Jenkins, Ky. '15 Abeel, George H., Jr., Cons Min Engr... . Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin , Univ. of Pittsburgh Pittsburgh, Pa. '28 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College. Pittsburg, Kans '20 ||Abernethy, D. Carl, Jr. Min. Engr., Hudson Coal Co . Scranton, Pa '27 Abey, Hiroshi, Min. & Met. Engr., Min. & Met. Dept, The Higher Technical School, Osaka, Japan. '17 Aborn, Robert H., Instructor in Met, Harvard University Cambridge, Mass. '19 Abozeid, Mahmood, Pet. Production Engr., Marland Oil Co Ponca City, Okla. '20 Abraham, Arthur W., Geol, Richfield Oil Co. Box 788, Bakeisfield, Cal. '20 Abraham, W. E. V., Member, Geol Staff of Burmah Oil Co, Ltd Nyaunghla. Upper Burma, India. '23

Jan 1, 1923

By P. G. Barnard

Losses of alloying metals in furnace flue dusts, grinding swarfs, and mill scale produced during the manufacture of stainless steel are substantial. About 25 million lb Cr, 8.7 million lb Ni, and 150,000 lb Mo and other critical metals can be made available annually for recycling by a process developed by the Bureau of Mines. Stainless steel wastes pelletized with a portland cement binder were reduced in a small electric-arc furnace by a two-stage process to produce a recyclable alloy containing Cr, Ni, Mn, and Fe. The initial reduction was with carbon; the second, with ferrosilicon. Results are compared with previously reported laboratory induction melting tests. A 2,000-lb demonstration test of the process in a commercial electric-arc furnace is also described. Data are also presented on three 1,500-lb tests made using various slag conditions in the electric-arc furnace. Recoveries up to 99 pct of the Fe, Cr, and Ni contents of stainless steel wastes were obtained in using the process.

Jan 1, 1977

CONTENTSThe significance of values givenINTRODUCTIONTHE ORE1. DATA SECURED FROM THE MILLING PLANT AS OPERATING BETWEEN 1938 AND 1942(a) Mill Recoveries(b) Mill Flow Sheet(c) Scheelite-Garnet Association(d) Detailed Examination of Mill Performance during 1942Crushing UnitsCoarse Rolls DischargeFine Rolls DischargeFeed to Huntington MillsFinal Ground ProductProduction of -200-mesh Scheelite SlimeSummary of Information on Crushing and Grinding Circuit(e) Detailed Examination of Mill Performance During 1942Concentrating UnitsLocation and Nature of Scheelite LossesSize Distribution of Scheelite LossesDistributor Spigot ProductsSummary of Information on Concentration Circuit(f) Detailed Examination of Mill Performance During 1942 Gravity Plant Feed2. EXAMINATION OF MINE SAMPLES TAKEN DURING 1942(a) Introduction(b) Nature of the Ore(c) Sampling of Mill Feed(d) Testing Technique(e) Minus 1/8-inch Ores-Naturally Broken Fractions(f) Recoveries from Plus 1/8-inch Fractions-Crushed to Minus 1/8-lnch(g) Probable Recoveries Obtainable from Weathered Ores140 Contour120 Contour90 Contour(h) Examination of an Ore Sample from the 90-foot Adit(i) Run-of-Mine Ore(j) Evidence of Maximum Sizes of Scheelfte Present in Run-of- Mine Ore(k) Summary of Information on Liberation and Recovery from the Ores as Mined in 1942 and from the Mill Samples

Jan 1, 1944

By J. Grignon, C. Fleming

It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch kinetic tests, coupled with mathematical models that translate kinetic data into predicted steady state gold profiles across multi-stage adsorption circuits. Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the step wise change can be determined. In this way it is possible to inexpensively optimize the operating conditions of an existing plant, with no disruption to plant operations and no economic risk to the mining company. This approach had been adopted by IAMGOLD to optimize the performance of their Rosebel CIL plant following several major expansions in mill capacity since 2004.

Jan 1, 2011

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

By J. W. Watkins

This report describes in detail methods of making corrosion tests and chemical analyses that have been used extensively and satisfactorily in a study of plants in which various surface, waters and brines are conditioned and used for water flooding, brine disposal, and reservoir-pressure maintenance in Kansas, Oklahoma, and North Texas. The tests and analyses described were designed and adapted for use in the field in determining the relative corrosive and plugging tendencies of waters from various sources conditioned by different methods. Although the described methods were developed and used in testing oil-field waters in the Midcontinent oil-producing area of the United States, these same methods should be equally applicable to testing oil-field or highly mineralized waters throughout the world. Many of the methods used have been discussed by the writer (1)2/ previously, and some of them have been used for similar work in other laboratories. Early in the development of the practice of the subsurface injection of brines for disposal and increasing the recovery of oil, it became evident that different methods of chemical treatment and conditioning equipment would have to be devised to sustain desired injection rates into water-input wells. These changes became necessary because the highly mineralized waters produced with petroleum from deep formations became chemically unstable when pumped to the surface, owing to loss of dissolved gases as pressure and temperature dropped to atmospheric and to the contact with atmospheric oxygen at the surface.

Jan 1, 1954

By Blade O. C.

This report is one of a series made by the Bureau of Mines under a cooperative agreement with the Coordinating Fuel and Equipment Research Committee of the Coordinating Research Council, Inc., on the characteristics of commercial aviation gasolines. The series of surveys is a continuation of like work conducted from 1940 to 1946 by the National Bureau of Standards under a similar cooperative agreement. A list of reports of previous surveys is given at the end of this paper.

Jan 1, 1950

By J, T C. McCuaig, J Hodgkison, T Fouet

Olympic Dam is the eighth largest Cu deposit and the largest U deposit in the world, with approximately 35 million tonnes of contained Cu and 1.2 million tonnes of U. The most recent resource estimate was for 2.95 billion tonnes of mineralised material with average grades of 1.2 per cent Cu, 0.4 kg/t U, 0.5 g/t Au, 2.6 g/t Ag as contained mineral resources. Olympic Dam is expected to produce >200 000 tonnes of Cu and 4200 tonnes of U3O8 from 9.8 million tonnes of ore in 2004, making it the 12th largest Cu producer in the world. One of the impediments to achieving targeted rates of production has been oversize material (>0.9 m) reporting to stope draw points. A major contributor to oversize material may be overbreak along pre-existing structural weaknesses from stope walls and backs during the production life of a stope. Underbreaking to structures can also have a detrimental effect on the performance of a stope. In an effort to understand the influence of structural geology on stope performance, WMC Resources and SRK Consulting partnered during 2003 to refine the current system of structural mapping, and to use historical data to produce a structural interpretation covering a large part of the mining area. The interpretation has been wireframed in DATAMINETM into a three-dimensional structural framework model. To date, there are more than 600 structures of >50 m strike length incorporated into the structural framework model, which covers a study area 1500 m + 600 m + 350 m. A back-analysis exercise to assess the influence of interpreted structures on overbreak and underbreak was completed for laser-surveyed stopes.

Jan 1, 2004

By Henry C. Meeves

The Bureau of Mines investigated the silver production potential of the Leadville (California) mining district, Lake County, Colo., in 1966-67. The mining history of the district, the ground conditions encountered in mining, and the mine-support methods used are reviewed. The drainage problem is discussed in detail. An initial objective was to establish the existence of potential silver resources minable by low-cost open-pit methods, particularly in the silver-bearing manganese halos surrounding the major deposits. The report concludes that under present conditions, development of the deposits in the area is not economically feasible; however, a pioneer rotary noncore drilling program demonstrated that this type of exploration is technically feasible. Potential reserves of silver and associated metals are estimated. Possible mining methods for recovery of the reserves are discussed. Future production possibilities from the various subareas of the district are analysed, considering optimum operating size. Consolidation of small individual holdings for unit operation is recommended. Type of operation, amount of rehabilitation, size and type of concentrating plants required, drainage and other mining problems, and metal price trends are discussed as they bear on economic feasibility of development.

Jan 1, 1970

By David J. Kusler

A gravimetric method for the determination of carbon dioxide, carbon monoxide, hydrogen, methane, and oxygen in blast furnace top gas is described. Nitrogen may be determined directly by volume measurement or by difference. The method is direct, permits continuous as sampling, and provides an averaged analysis over a selected range of sampling intervals from 1/2 to 24 hr or more. Neither expensive equipment nor specialized personnel are required. The method is suitable for routine analysis, and the results compare favorably with those obtained by established methods.

Jan 1, 1963

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By K. Reinhardt

THE idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size bad been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Maschinenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cyl¬inders of the Oechelhäuser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high of efficiency, considering the period. The builders were therefore

Nov 1, 1906

By D. A. Reynolds, J. D. Davis

"INTRODUDTION Investigations by the Bureau of Mines have shown that the carbonizing properties of splint and bright coals may differ greatly. In a study of 55 coal columns selected from representative coals of the Appalachian region, Sprunk and coworkers 10/ compared various chemical and physical properties of splint and associated bright coals. Carbonization tests in the Fischer retort at 932°F. (500°C.) showed that, except for bright coals of high oxygen content, the coke residue from bright coal was much more swollen and cellular than that from splint. ·with one exception, agglutinating values determined by the Bureau of Mines test, were lower for splint than for associated bright coal.Because sorting of coal in quantity is tedious and time-consuming, separate types have not been carbonized by the Bureau of Mines-American Gas Association (BM-AGA) test, which requires 85- to 200 pound charges. However, this method has been used to determine the carbonizing properties of samples 0f bed layers that are composed largely of either splint or bright coal.4/ In these earlier tests, which were made at high temperatures on layer samples from the Elkhorn bed, Letcher County, Ky., the splint coal yielded more coke than the bright coal, and this coke was slightly stronger than that from the bright coal. The cokes from samples with large proportions of bright coal were more cellular or porous, as were the low-temperature cokes obtained from carbonization of separated samples of bright coal in the Fischer retort."

Apr 1, 1944

By Gordon E. Frantti

Under the auspices of the Geophysical Committee of Michigan College of Mining and Technology, an investigation was made in Michigan's Upper Peninsula to obtain geophysical data related to the regional subsurface geology in the area covered by Paleozoic sediments. The area surveyed includes that portion of the Upper Peninsula which lies between R18W to R26W and T41N and T49N, covering approximately 1300 square miles. On the index map, Fig. 1, it is represented by the cross-hatched zone west of Munising. Four of the five sites of detailed investigation are indicated by the letters A, B, C, and D. A detailed gravity and magnetic survey had previously been conducted by J. G. Wilson near Perkins, 8 miles north of Rapid River, on a local anomalous area. Results of his work, which showed a large positive magnetic anomaly associated with a gravity anomaly, aroused interest in the possible economic significance of the formations underlying the Paleozoic sediments in this part of the Upper Peninsula.

Jan 1, 1956

By D. K. Fountain

"High metal prices and advanced technology in open-pit mining methods have resulted in considerable interest in the development of large, low-grade mineral deposits. Brenda Mines Limited is presently testing such a deposit of copper-molybdenum mineralization near Penticton, British Columbia.The mineralization of economic interest at Brenda has a total metallic sulphide content of between 1 and 1.5 per cent. This sulphide content approaches the limits of detectability of standard geophysical methods. How-ever, due to a favourable geological environment, it has been possible to utilize the Induced Polarization Method to outline the mineralization at the Brenda property."

Jan 1, 1968

By K. W. Edwards

The formulation of a theoretical basis for the evaluation of in-situ coal through the use of geophysical logs is outlined. This involved the development of an approach to the interpretation of resistivity in environments having multiple conductive and non-conductive components. Utilizing this approach and other conventional interpretation techniques, a program was developed yielding accurate determinations of the in-situ percentages of coal, water and ash for the evaluation of coal deposits. Basic information obtained from the CWA program can be utilized in numerous aspects of total mine planning . Some examples of the practical application of this method are included.

Jan 1, 1978