Search Documents

By William H. Tavenner

1. The 1952 Annual Report of the West Virginia Department of Mines lists nine beds that arc being mined in Logan County, of which the Cedar Grove and Chilton are the most important. The Cedar Grove group, No. 2 Gas, and Alma beds have the largest remaining reserves, in the order given. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 5,411 million tons as of January 1, 1954. Of this total, 3,939 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimate reserves.

Jan 1, 1956

During the first quarter of 1973 ADL worked closely with PMSRC staff, under an extremely compressed time schedule, on all aspects of the detailed planning, organization and overall coordination and preparation of the lectures and in-mine demonstrations for the Bureau's Technology Transfer Seminar on Mine Communications given in March of 1973 to representatives of the mining industry. Our efforts centered on the detailed organization and preparation of each of the five technical seminar lectures and associated supporting material, and the coordination of tasks assigned to ADL and other seminar participants. Revised and expanded drafts of the seminar papers were prepared from rough draft versions obtained from PMSRC, Collins Radio and ADL staff. Measurements were made to gather key data on the operation and performance of each of the following systems installed in the Bruceton Safety Research Mine; call alert paging, roof bolt paging, section wireless radio, and guided wireless radio systems. These data were analyzed, manufacturer's equipment specifications utilized, and calculations made to provide performance curves and data for each of the above systems. A substantial amount of artwork was conceived and prepared for 35 m slides, system identification posters in the mine, and seminar handouts. This artwork included some forty 8-1/2" x 11" line sketches, graphs, block diagrams, circuit diagrams, coverage maps, and other line drawings; five 30" x 40" block diagram system identification posters suitable for in-mine use; a 20" x 30" detail perspective illustration of a representative coal mine layout; forty viewgraphs; and seventy 35 m slides of the artwork and word charts. Conferences, discussions and review sessions were held with conference participants to help coordinate the various efforts, obtain technical information, and make final plans regarding the lecture presentations, associated visual aids, and the communication system installations to be demonstrated in the Bruceton mine. These meetings included final systems checkouts and dry run presentations and reviews of the lectures and mine demonstrations. This phase of the seminar effort concluded with R. Lagace and R. Spencer of ADL participating in two days of seminar presentations in the lecture hall and in the Bruceton mine.

Jan 1, 1974

By Richard A. Kesler, W. Michael Reed

Grindability or resistance to fine comminution is the fundamental issue involved in the application and sizing of grinding mills. Over the years, many theories for determining the amount of energy required for size reduction to a specified fineness have been proposed. The first published theory, introduced by P. R. von Rittinger in 1867, stated that the energy required for crushing or grinding is proportional to the increase in surface area produced. The surface area of a ton of particles of diameter (d) is proportional to (1/d), therefore the work input per ton for particles of diameter (d) would be proportional to (1/d). The second significant theory is that of F. Kick published in 1885. Kick said that the work required is proportional to the reduction in volume of the particles concerned. If (f) is the diameter of the feed particles and (p) is the diameter of the product particles, the work input relationship would be: [W =Ioq(f/p) 9] The "Third Theory" of F.C. Bond, introduced in 1951, states that the work required is proportional to the length of the new crack tips produced in particle breakage during crushing or grinding and equals work represented by the product minus that represented by the feed. This takes the form: [W=]

Jan 1, 1982

By Jean-François Boulanger

The production of rare earth elements from ore usually consists of three steps; the separation of a concentrate of REE bearing minerals; the cracking of the REE minerals to liberate the REE into an aqueous solution and separation of REE into individual elements. This paper describes the results of laboratory tests conducted on a carbonate-rich REE ore containing bastnaesite and monazite. The tests cover the whole processing sequence of beneficiation, preparation of the REE solution using a caustic leach followed by acid leach to break monazite and bastnaesite and liberate REE into an aqueous solution and the partial separation of the REE using solvent extraction. Details on the product quality and process performances (recovery and impurities removal) are given for each studied step. The paper also discusses the economic advantage of separating the REE rather than producing a mixed REO product to be sold to a refinery for REE separation. A mini-pilot plant version of the process is currently planned.

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700” F.

Jan 1, 1996

By Leandro Pérez

La flotación es una actividad que se aplica naturalmente en pequeña escala y con elementos empíricamente buscados para flotar plomo, zinc y así obtener la amalgamación del oro y la plata. En este sentido, el presente texto señala los cambios (slimes) del proceso de flotación que se realizaron en la concentradora de Carahuacra. Actualmente existe un tratamiento para slimes llamado «Ultraflotación» aplicada a la flotación de caolín donde después de flotar los slimes ( skin) regresan nuevamente a las espumas de flotación, cerrando el circuito varias veces (piggybacked), observándose que todas las partículas del mismo polo son flotadas bastante limpias.

Jan 1, 1966

By S. K. Sharma, R. Markandeya, G. Venkateswara

"In this study, a three level Box- Behnken factorial design combined with Response surface methodology (RSM) for modeling of process parameters of Multi Gravity Separator (MGS) for recovery Iron values from sub grade iron ore, Deposit No. 5, Bailadila complex has been developed. The three significant operational parameters of MGS, Drum rotational speed (RPM), Drum inclination (degrees) and quantity of wash water (LPM) were considered in the experimental work. Other parameters like feed percent solids, shake frequency and shake amplitude were maintained constant. The ‘as received’ sub grade iron ore sample is admixture of lump and fines and chemically assayed 40.80% Fe, 40.90% SiO2, 0.24% Al2O3 and 0.22% Loss on Ignition (LOI). The obtained results were evaluated with the Box-Behnken factorial design, RSM and also Quadratic programming(QP). Second order response functions were produced for Fe in terms of grade (%) and recovery (%) of the concentrate fraction. Taking advantage of QP, it was observed that maximum grade of 62.21% Fe achieved at an inclination of 4.3degrees, 2.7LPM of wash water and at a drum speed of 198 RPM. Similarly a maximum Fe recovery of 65.37% weight can be achieved at 4.3degrees inclination, 2.6LPM wash water and at a rotational speed of 212 RPM Predicted values of responses obtained using model equations were in good agreement with the experimental values. The influence of the process variables of the multi gravity separator concentrator on grade and recovery of concentrate fraction were presented and discussed."

Jan 1, 2014

By Liu Chun-Bao Sun, Hong-Jun, Wei Zhang, Tao Xu

SABC circuits have gained widespread attention within China, and are being gradually applied to many mines. However, the domestic knowledge of comminution process is still relatively basic, and the design and production management of the application of SABC technology lack guidance of scientific theories. This research project focuses on the Phase I SABC milling circuits of Wu Shan Porphyry copper mine. Targeting the design and operation problems of existing process and circuit, and without increased investment and alterations in equipment, the new technologies will combine ordinary crushing and grinding theories as theoretical guidance, and borrow JK Simulation Software (JKSimMet) for analysis in order to optimize the comminution process, efficiently allocate production output and energy consumption, eventually resulting in increased production and energy efficiency. Using JKSimMet Simulation Software, and combining theoretical optimizing and practical production techniques, as well as the on-site situation, the eventual SABC comminution process and circuit optimization plan is: increasing the grinding Ball charge from 8% to 10% v/v in the SAG mill; Setting the Ball charge in the Ball mill to 27% v/v and the maximum operating power draw to 5 800kW; replacing the HP Series crusher with a TRIO TC84 crusher, which is without a power controller, and adding a pebble bin. The final optimization result is: Maximum system processing capacity increased between 20%-26.7%, specific energy consumption reduced by more 2.0 kWh/t, creating an economic benefit of over 300 million RMB, thus achieving the goal of increased production, reduced energy consumption, and improved profitability.

Jan 1, 2014

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

On Sept. 22 to 26, the Institute will hold its 120th meeting in Chicago. The program arranged provides for technical sessions on: Mine Taxation, Non-ferrous Metallography, Coal and Gas, Milling, Oil, Industrial Organization, Geology, Non-ferrous Metallurgy, Mining and Local Resources, Iron and Steel, Symposium on Sulfur Coals, Symposium on Pyrometry. Inspection trips have been arranged to: Gary Steel Plant. La Salle District: Zinc smelters, coal mines, cement works, America's first permanganate plant, many varied industries, scenic trips. North Chicago and Milwaukee: Mining-machinery manufacturing plants, tungsten and molybdenum reduction plants. East Chicago and Whiting: Lead refinery, oil refinery. Franklin and McCoupin: Coal fields. Chicago: Nearly every kind of metallurgical and manufacturing industry. MONDAY, SEPT. 22d Morning Registration, Non-ferrous Metallurgy, Coal and Gas. Afternoon Coal and Gas Milling Industrial Geology, etc. Evening Smoker. TUESDAY Morning Gary. Afternoon Gary. Iron and Steel. Evening Oil, Iron and Steel.

Jan 9, 1919

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By William Connell

NFPA 502, Standard for Road Tunnels, Bridges and Other Limited Access Highways establishes minimum fire protection and fire life safety requirements for road tunnels, bridges and other roadways where access by emergency responders is physically limited. The 2008 edition of NFPA 502 represents the Technical Committee?s consensus of current best practice for fire protection and life safety requirements for road tunnels, bridges and similarly limited access highways. Research of national and international test programs, design guidelines and regulating standards was per-formed and considered in an effort to establish a singular, comprehensive document representing a recognized base threshold of fire safety in these type facilities. This paper provides an overview of the more significant revisions including the application of fixed fire suppression systems, guidance on tenable environment, protection of structure and dangerous goods transport.

Jan 1, 2008

By Mario Samamé Boggio

La ausencia de la enseñanza adecuada en el comportamiento mecánico de materiales y la falta de análisis en los cursos de ingeniería, señalan un problema de neutralidad e integración del concepto de ingenierías en la educación universitaria. En ese sentido, el presente texto describe la importancia de la enseñanza con la realidad del ingeniero, las implicancias de sus especialidades y su rol político como ciudadado que conoce para mejorar la vida humana en el universo.

Mar 1, 1979

THE Lehigh Valley Section is planning with a num-ber of other organizations a three-day conference, April 25, 26 and 27, with field visits to cement, slate and steel plants in the vicinity of Easton, Pa. W. B. Plank is chairman and D. Knickerbocker Boyd is sec-retary. Headquarters will be at Hotel Easton. Wednesday' will be cement day. In the forenoon A. S. T. M. Committee D-16 will meet and after luncheon the delegates will visit the Martin Creek plants of the Alpha Portland Cement Co. An evening dinner and general session on cement is being arranged. Thursday morning will be devoted to a technical ses-sion on slate, and the breaking of ground for the new John Markel mining building at Lafayette College. After luncheon various slate quarries will be inspected, the visitors being guests of the companies. In the eve-ning there will be a conference dinner at Hotel Easton with a number of distinguished visitors. Friday will be given over to steel and will include a visit to Lehigh University, an inspection of the plant of the Bethlehem Steel Corp., and a luncheon as guests of the latter.

Jan 3, 1928

By W. F. Boericke

AT Kellogg, Idaho, J. Fred Johnson is driving the 5000.-ft Hooper Tunnel under contract for the Bunker Hill & Sullivan Mining Co. This was visited by a group of engineers during the recent meeting of the A. I. M. E. at Spokane, who were impressed with several features of the work. An excellent record of advance is being made by the contractor, over 47 ft. being driven in 3 days during October, and 223 ft. advanced in 29 shifts. The size of the tunnel is 8 by 9 ft. The ground is Wallace quartzite and, save for the first hundred feet, stands well and does not require timbering. The grade is held uniformly at 0.5 per cent. Two shifts are employed, with two sets of machine men to the shift. Ingersoll-Rand S-70 drills are used. each machine being set up independently in the heading; 26-30 holes are drilled to the round; using 1 1/4: in. round hollow drill steel. A 7-hole cut is required, and these holes are blasted simultaneously, using 60 per cent gelatine, 12 sticks to the hole. Instantaneous and fire delays of electric detonators are used for the complete round. A feature of the drilling is the use of long carriage drills, necessitating fewer changes of steel, and more time spent on drilling, with less time consumed taking steel back and forth from the face. Of course, this means better blacksmithing so that the drill steel shall stand up for the added footage.

Jan 1, 1930

By C. M. McKinney

This report presents analyses of crude oil from most of the fields in the United States producing 2,500 barrels per day or more. The purpose of the report is threefold : 1) To present detailed analyses of crude-oil samples from as many al possible of the important fields in the United States. On January 1, 1947, there were 340 fields producing 2,500 barrels & day or more. Analyses for 283 of these fie1ds are presented. Fifty-seven fields have been omitted because the Bureau of Mines did not have analyses or the crude oils being produced. As one sample was not representative of the promotion from several of the fields, two analyses are given for each field of this kind. (2) To compile these analyses, many of which have not been published previously in a single report. Since the publication of Bulletin 291 in 1928, there has been no report showing analyses of crude petroleum from fields throughout the United states, but a number of separate reports according to area or state have been issued. Many of these are out of print. (3) To provide a means of ready comparison of the properties of crude oils from different areas of the United states.

Jan 1, 1948

By D. K. Deardorff

The purpose of this work was to investigate the hafnium-carbon phase diagram. Alloys used to study this system were prepared from high-purity components by both consumable-and nonconsumable-electrode arc melting. Data for the diagram were obtained on the alloys by metallography, optical pyrometry, thermal analysis, heat treatment, and X-ray diffraction. The data indicate that a carbide compound occurs over considerable range of composition, and that one of each of the following types of reactions occurs in the hafnium-carbon system: Peritectoid, peritectic, and eutectic. The maximum melting temperature of hafnium carbide is 3,840° C at 49 to 50 atomic percent carbon, and the composition range of hafnium carbide at temperatures of 2,150° to 2,380° C is from 37.0 to 48.5 atomic percent carbon. The hafnium a-S transformation temperature is raised on alloying with carbon from 1,750° to 1,890° C, where a peritectoid reaction isotherm occurs. Alloying hafnium with carbon increases the hafnium melting temperature from 2,190° to 2,250° C, at which temperature a peritectic reaction occurs. Hafnium carbide and carbon react at 3,055° C to form a eutectic of 68.3 atomic percent carbon.

Jan 1, 1967

By Terry L. Muldoon

The report describes the development of preliminary requirement specifications for standardized operating controls for roof bolting machines used in underground coal mining. According to recent statistics, roof bolting continues to be one of the most hazardous occupations in underground coal mining. The two principal hazards to the roof bolter operator are the machine itself and roof falls during the bolting cycle. The lack of standardization of machine controls is a major contributor to this hazardous situation. Observations of roof bolting operations and discussions with roof bolter manufacturers coupled with detailed analyses of roof bolter control design specifications were performed during this study. Detailed roof bolter operator task analyses, commonality of control analyses, and classical link analyses were also performed. The results of these analyses were then used to produce preliminary requirement specifications for standardized controls.

Jan 1, 1980

By R. F. Stewart

A key step in changing coals to fluid fuels and chemicals is the conversion of coal to synthesis gas by gasification with steam and oxygen. As oxygen represents one of the largest single expenses in gasification, its cost is a vital factor in the economy of the process. At present, the most economical method for producing tonnage oxygen is by the conventional rectification of liquefied air. Several alternate methods have been proposed for producing oxygen from air: (1) methods based on physical or chemical sorption of oxygen from air by liquids or solids or (2) the oxidation of certain inorganic com-pounds to higher oxides unstable at higher temperature levels. Economic limitations are discussed by which these methods may be evaluated. Chelated metals of the salcomine type are promising chemical sorbents of oxygen from air. This report covers a study of the reversible sorption of oxygen by salcomine and other chelates. The presence of water in the salcomine structure was verified; it is the loss of this water that causes slow deterioration of salcomine during cycling.

Jan 1, 1959

The brown coal deposits of the Latrobe Valley are ideal for open cut mining and this method has been used since the start of coal winning in 1894. Operations at the main Yall9urn open cut commenced in 1922, but after a few years the main excavators were replaced by German continuous excavators and subsequent developments of Yallourn and the newer Morwell open cut have been based on this type of plant. The reasons for preferring continuous to intermittent excavators in the Latrobe Valley are indicated in this paper.Under the pressure of post-war conditions, and from their long experience and ability, German engineers have recently made substantial improvements in their continuous excavators and these developments have been enhanced by some American innovations. These changes have extended the economic limits of open cut mining and also serve to emphasize the close inter-relation between the nature of coal and overburden deposits, excavator design and methods of operation.As an aid to descriRing recent excavator developments, this interdependence is demonstrated by means of diagrams which show typical methods of operations, together with examples of actual machines using these methods. The types of excavator dealt with are mainly those in use at, or destined for Yallourn or Morwell open cuts, together with additional types used in U.S.A. and Western Europe. For completeness, and also because they will continue in service at Yallourn and Morwell for some years, rail-mounted dredgers have been included in this paper even though in Europe they are now regarded as obsolescent.Explanations are given of how the intrinsic qualities of Latrobe Valley brown coal and overburden have sometimes prevented overseas plants from operating with the full efficiencies and/or in the methods visualized by the manufacturer, and references are made to the modifications and investigations being undertaken to overcome these problems.A compresensive bibliography is given. Dates shown on illustrations are not commissioning dates of the plant concerned, but the year when photographed.

Jan 1, 1960