Search Documents

By H. C. Fowler

Hydrogen sulphide associated with the gasps and vapors from certain crude oils now produced in the United States has forced a serious health and safety problem upon the petroleum industry. Although the presence of hydrogen sulphide in or occurring with Mexican crudes has been known for some time, it was not until recently that crude oils which give off poisonous amounts of hydrogen sulphide have been produced to any extent in the United State. The injurious effects of this poisonous gas were first recognized by the refiners along; the Atlantic and Gulf Coasts upon receiving shipments of crude petroleum from Mexico. The problem of combating the hazards of the gases and vapors given off by this petroleum become more important as the use of Mexican crude increased. In 1925, the Bureau of Mines and Public Health Service under cooperative agreement with the American Petroleum Institute, studied the causes rend effects of hydrogen sulphide poisoning. Bureau of Mines Bulletin 2312 is report of this investigation, and although written with special reference to refineries, it nevertheless contains much information that is of value to the producer of petroleum.

Jan 1, 1927

By Tim F. Dyson

Feasibility of employing automated processing and detection techniques in the mine disaster communications problem is demonstrated. Efficient processing methods are developed. These methods have been demonstrated both in a laboratory and in a field environment. Evalua¬tion of existing computer capacity is given along with recommendations for expansion.

Jan 1, 1981

By M. L. Glenn

The Bureau of Mines is conducting research on Fe-based alloys using Si and Al additions to reduce the Cr required for heat-resisting appli-cations. Part of this research is being done to evaluate alloys containing (8-10)Cr-(10-14)Ni-(0-8.5)Si-(0-4) Al to determine which of these alloys have austenitic structures, as well as fabrication properties and oxidation resistance sufficient to substitute for type 304 stainless steel. Based on initial results, an Fe-lOCr-11Ni-5Si alloy and an Fe-8Cr-13Ni-5Si alloy were selected for evaluation of oxidati.on, stress rupture, and tensile properties. Both alloys have oxidation resistance at 7000 and 8000 C that is better than that of type 304 stainless steel. The stress rupture strengths are less than that of type 304 stainless steel but significantly better than that of commercial heat-resisting steels with similar Cr contents. Yield strengths of the alloys were equivalent to that of type 304. Both alloys had high tensile strengths comparable to those of stainless steels that transform to martensite during straining (e.g., type 301). These alloys have weld-hot-cracking resistance comparable to that of type 304 stainless steel. This initial study shows that Si has potential as a substitute for Cr in stainless steels for heat-resisting applications.

Jan 1, 1984

By Edgar Stanfield

Since April, 1923, the Scientific & Industrial Research Council of Alberta has had an analyst, Mr. W. P. Campbell, steadily employed analyzing coal samples taken by the provincial Mine Inspectors. Mr. Campbell has also analyzed a number of coal samples taken by one of the Council's Geological Survey parties. We have thus, at the time of writing, over four hundred analyses of Alberta coal, made by the same analyst, and strictly comparable. These samples come from widely distributed points, some 88 townships being represented. The stream of samples is still flowing in, and it is hoped by the end of this year that the number of townships represented will be increased at least fifty percent. The time has arrived to publish some of the data collected; but it must be clearly understood that this is merely a progress report, subject to revision as further information is obtained. Three hundred and fifty-three coal mines in the province were operated during 1923. The production per mine varied from 5 up to 500,000 tons. With this number of mines to examine (and fresh mines are being opened every year) it is a large task to make even a proximate analysis of representative samples from every mine. Any chemist will appreciate the fact that to make ultimate analyses representative of even the larger mines will be a long and tedious task. It has seemed better to make a comprehensive survey by proximate analysis and determination of calorific value before beginning the more thorough survey by ultimate analysis. This paper, therefore, deals only with proximate analyses and calorific values; and, owing to limitations of time and space, does not deal with other chemical and physical characteristics of coal, such as storage quality and fusibility of ash, important though these are.

Jan 1, 1925

By R. W. Watson

In January 1980, the Bureau of Mines initiated an experimental program to examine the fire and explosion hazards of one-hour self-contained self rescuers (SSRs). This action was prompted by a growing concern on the part of government and industrial safety officials over the potential hazards of these devices when deployed on a large scale in underground coal mines. Prior evaluation of the safety of these devices had been at best sporadic and usually limited to experimental models. The recent availability of preproduction models of a l-hour SSR fabricated by the Mine Safety Appliance Company* and a production model manufactured by Dragerwerk Ag Lubeck of the Federal Republic of Germany allowed for a more comprehensive and meaningful evaluation of their safety in underground coal mines. This report summarizes the results of a 5-month study of the potential hazards of these two items. During the course of the work, periodic progress reports were presented to officials of the Mine Safety and Health Administration and various mining organizations including the American Mining Congress, Bituminous Coal Operators of America. National Independent Coal Operators Association, and the United Mine Workers of America. The free exchange of ideas that occurred during these meetings had a significant impact on the direction of this study and a serious attempt was made to address all of the issues that were raised at these meetings. The authors are extremely grateful to the individuals that participated in defining the specific problems that could arise as a result of deploying the self-contained self rescuers in an underground coal mine environment.

Jan 1, 1980

By James L. Elder

Field-scale experiments were conducted at Gorgas, Ala., from 1951 to 1954. Three reaction paths were formed by electrolinking-carbonization, using electrode spacings of 150, 152, and 155 feet. The coal along these reaction paths was gasified, using air, oxygen, and steam separately or in various combinations. At the conclusion of operation, a drilling survey was conducted to determine the location and approximate area of the reaction zones. During the applications of the electrolinking-carbonization technique the maximum limitation on electrode spacing was not determined. Initial tests were conducted at 60-foot spacing. Successful path-preparation tests were made at 150-, 152-, and 155-foot spacings, and the indications were that much longer spacings were possible. The potential requirements appear to be constant, regardless of path length, while the gross power required probably will increase with path length. During the carbonization phase gas was produced that is similar in quality to coke-oven gas produced at low to intermediate temperatures.

Jan 1, 1957

By G. L. Oldright

In an earlier series of 15 Reports of Investigations on Smelting in the Lead Blast Furnace, experimental data were given on the operations of a custom smelter, a smelter treating rich lead products, and a smelter treating highly zinciferous charges. Five "reports" were written on each of the three types of operation, which were later compared in a summary written for the Institute. Developments in each of these types of operation in lead smelting since the last of the above reports was written have continued and have followed modifications necessitated by changes in the nature of the products received for smelting. The sintering-blast furnace-smelting plants have improved their sintering operation .and have made "2-pass" sintering a more standard operation; the richer lead feeds are diluted when marginal precious metal ores are not available to prevent fusion of the sinter cakes and to permit air to contact the sulfides. Means have been devised to make it easier to remove metallic lead from the wind boxes, but no attempts have been observed to use the D & L somewhat as an ore hearth to make more metallic lead. Except in those cases where zinc-rich lead blast-furnace slags were to be retreated in a "slag-fuming furnace," the sintering and the blast-furnace operations were so carried out that a relatively "clean," lead-poor, final slag was discarded.

Jan 1, 1949

By J. A. Holmes, EDWARD C. FRANKLIN, RALPH A. GOULD

The commission may be permitted to express its earnest hope that the litigation which comes to an end with the findings and recom- mendations herein set forth will be considered by both parties to the action as definitely and equitably decided. The commission trusts that its work will show the value of the commission form of settlement and that its work will serve as a prece- dent to be followed in disputes relative to technical subjects. If the work of the commission is productive of a tendency on the part of technical litigants to avoid the use of the courts for the settlement of disputes it will not have been done in vain. Such tendency will surely grow and ultimately such differences will be arbitrated by technically trained men without recourse to the courts of law. Appended to the report of the findings of the commission are to be found the detailed reports covering the several lines of inquiry and investigation carried on by the commission and upon which its findings are based, and also a detailed statement of the fiscal affairs of the commission. A word of explanation is necessary in regard to the fiscal statement. While each party to the litigation has agreed to bear one-half of the expense of the investigations of the commission, it will be noted that the Selby Smelting & Lead Co. is credited with $21,000, while Solano County is credited with but $6,000. In order that the investigations of the commission might go forward without interruption the Selby Smelting & Lead Co. has generously supplied funds at the times they were needed. This assistance has been

Jan 1, 1915

By R. A. Cattell

Every finding of the year's work, obtained under stress to meet present objectives, contributed to postwar needs, because the very nature and constitution of petroleum and natural gas require that research be conducted along the same general lines whether the results are applied in peace or war. More than 40 reports were submitted to the Petroleum Administration for War and others concerned with (1) evaluation of crude oils to determine their content of aviation-gasoline base stock, (2) evaluation of base stocks for blending with high-octane, synthetically manufactured components, (3) analyses of naphthas to determine their content of various types of hydro-carbons, such as benzene and toluene, and (4) the improvement of quality of marginal base stocks to meet future requirements of aviation gasoline. This upgrading of marginal stocks is being attained by selective distillation and chemical and catalytic removal of sulfur compounds. Asphalts were studied with respect to the characteristics of their various constituents in order to compound them, in the same way that aviation fuels now are being "built" to meet exacting requirements. The work previously initiated to give the industry fundamental data on thermodynamics of hydrocarbons progressed satisfactorily, and the heats of combustion of 10 hydrocarbons in the lubricating oil -range of petroleum were determined. Thermodynamic data requiring highly specialized techniques are so broad in application that their commercial usefulness is not yet fully appreciated.

Jan 1, 1946

By Jorge Ganoza

El proceso del diseño de circuitos de molienda (SAG) en la planta de flotación de pórfidos de cobre, flotación de minerales polimetálicos o plantas de cianuración y minerales de oro y plata, implica energía que puede variar al procesar minerales blandos o duros. En este sentido, se buscan las operaciones que acepten el tratamiento de minerales duros en los circuitos de molienda y la clasificación del mineral de acuerdo a la dureza.

Sep 1, 2016

"For a good many years the Bureau of Mines and various state mining experi¬ment stations have endeavored to develop some method of utilizing the immense deposits of lignite in the United States. Work in relent year has indicated that the best method of this is to drive off the moisture and most of the volatile water from the lignite in some form of carbonizing apparatus leaving a residue high in fixed carbon and low in moisture and volatile matter, which by briquetting can be made into a high-grade fuel. The earlier forms of carbonizing equipment tried were complicated, costly to build and keep in repair, and could not be operated intermittently without being seriously damaged. During the year 1922, however the Bureau of Mines devised a very simple carbonizing oven which produces a uniformly well carbonized product. This oven is essentially a vertical shaft with means for supplying raw lignite at the top and discharging the carbonized limited at the lower end. Air in regulated amount is admitted to the shaft at two horizons, and a zone of combustion maintained through which the column of lignite passes. The lignite is thus carbonized by construction of its contained matter and a small proportion of its fixed carbon, leaving most of the fixed carbon in the carbonized product or ""char"". The degree of carbonization can be closely controlled by varying the volume of air supplied to the oven and the rate of travel of the charre down the shaft.The ""lignite char"" produced is a soft material resembling charcoal more than coal or coke, but somewhat harder than charcoal. A typical analysis is shown in the table headed ""Fuels,"" further on in this papers."

Feb 1, 1924

1. Proposals were submitted to the Western Administrative Center of the US Bureau of Mines, Denver, Colorado on 30th December, 1974 and Contract No J 0255003 was awarded, the effective date being 8th May, 1975. Dames and Moore, Denver, are associated with PD-NCB Consultants in regard to environ-mental problems, surface mining practice and legislation in US. BACKGROUND TO THE STUDY 2. Under the threefold pressures of -increased domestic fossil fuel demand -increased value of domestic energy resources -increased demand for environmental protection and safety

Jan 1, 1976

By Davood Moradkhani, Maryam Rasouli

"The present study reports solvent extraction and separation of zinc from concentrated nickel sulfate solution. In our previous study, Zn and Cd in cold filter cake (CFC, 45-55% Zn, 11-16% Cd, and 2.5-4% Ni) were extracted by alkaline leaching followed by electrowinning processes respectively. The strip solution from electrowinning process, was a pregnant liquor solution (PLS) containing 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process for separation of traces of Zn from high grade nickel. The zinc free raffinate containing 16.6 g/l Ni sulfate solution will flow to nickel electrowinning plant for cathode production. Di-(2-ethylhexyl) phosphoric acid (D2EHPA) is the organic phase used in this study. The effects of various parameters such as organic phase concentration (10- 40 % v/v), pH (1.5-3), and temperature (25 and 45°) are investigated. Zinc over nickel separation factor increases by increasing pH from1.5 to 3. The results show that 98.7% of Zn was loaded at25°C O/A ratio of 1, pH 3, and 10% vol. D2EHPA. A 10 M NaOH is used for pH control. However, replacement of pH controlling agent with ammonia solution (25%. v/v) results in interesting observations. Ammonia addition, reduces the solubility of Ni2+ cations in solution. Nickel starts to precipitate from raffinate in a crystalline bluish-green form. The obtained crystals are characterized by XRF and identified to be nickel-bearing analog of boussingaultite, a rare sulfate mineral of nickel with chemical formula of Ni (NH4)2(SO4)2.6H2O. The crystallization rate of crystals is studied. It is a slow precipitation process with 75% in 4 days.INTRODUCTION Annually, many hydrometallurgical processes such as electrowinning, solvent extraction and leaching are applied to waste filter cakes in Zanjan, Iran. These additional processes on filter cakes are critical from both environmental and economic points of view. CFC (cold filter cake) is a toxic but valuable filter cake (45-55% Zn, 11-16% Cd, 2.5-4% Ni, and 0.2-1.5% Cu) produced in many zinc production plants. Our research group at Research and Engineering Company for Non-ferrous Metals (ReCo.), developed a series of hydrometallurgical methods for extraction of zinc, cadmium and nickel from CFC (Moradkhani, & Rasouli 2012). The recovery of zinc and cadmium with alkaline leaching and electrowinning was successfully studied. The strip sulfate solution from cadmium electrowinning unit, contains high concentration of nickel with some traces of zinc impurity. This pregnant liquor solution (PLS) was analyzed and reported to contain 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process to separate Zn from nickel (Fig. 1). The organic phase stripping solution containing 4.2 g/l zinc and 200 ppm nickel can be circulated and used in the acidic leaching step. This generates nickel solution with high purity suitable for nickel cathode production."

Jan 1, 2017

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)–based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry, and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jul 7, 2023

By W. W. Adams

"The fifth annual National Safety Competition conducted by the United States Bureau of Mines to determine the best safety records at mines and quarries during the calendar year 1929 has been concluded, and the general results of the contest are presented herewith. To the winner in each of the five groups into which the contestants were divided there has been awarded the bronze trophy 'Sentinels of. Safety,' donated by the Explosives Engineer magazine. The trophy for bituminous coal mines was won by a mine in Alabama; that for metal mines by an iron-ore mine in Michigan; that for nonmetallic mineral mines by a salt mine in New York; that for quarries and open-cut mines went to a limestone quarry in Michigan;. the trophy provided for anthracite mines was, of course, won by a mine in Pennsylvania, as all of the anthracite mines participating in the contest are situated in that State.Winners of the trophies were selected by a committee of sward in accordance with rules governing the contest and on the basis of accident records furnished by the various companies to the Bureau of Mines. These records were summarized by the bureau and the results submitted to the committee. Members of the committee are W. H. Cameron, managing director of the National Safety Council. William Green, president of the American Federation of Labor; James F. Callbreath, secretary of the American Mining Congress; T. T. Read, Vinton professor of mining of Columbia University and editor of 'Mining and Metallurgy'; C. B. Huntress, executive secretary of the National Coal Association; A. J., Curtis, assistant to the general manager of the Portland Cement Association; A. T. Goldbeck, director of the engineering bureau of the National Crushed Stone Association.Thirty-four States were represented in the l29 contest. Among the plants which participated were 68 bituminous coal mines, 29 anthracite mines, 54 metal mines, 19 nonmetallic mineral mines, all of the foregoing being underground mines, and 141 quarries or open-cut mines. A total of 106,533,006 man-hours of work was reported by all of the companies. Accidents during the year numbered 7,008 and represented a period of disability equal to 986,306 man-days. Hence the accident-severity rate for all plants combined represented 9.3 man-days of disability for each thousand man-hours of exposure to hazard. Similarly, the combined accident-frequency rate for all plants showed that 66.3 accidents occurred for every million man-hours of exposure to hazard. Both of these rates indicated an improvement over the combined rates for all plants in the previous year's contest. The reduction in the accident-severity rate centered chiefly in the metal mine group, though all except the quarry and open-cut mine group shared in the reduction; the improvement in the accident-frequency rate was in all croups except anthracite and metal, the rate for the former having increased while that of the latter remained unchanged."

May 1, 1930

By W. L. Dare

This publication is one of a series by the Federal Bureau of Minus describing methods and costs of minim, uranium on the Colorado Plateau. The La Sal mine is in the Big Indian mining district, about 29 miles southeast of Moab, San Juan County, Utah. The claims that encompass the mine were located in March 1953, and the La Sal ore body was discovered as a result of a drilling program begun in August 1953. The mine is owned by the La Sal Mining & Development Co., a subsidiary of the Homestake Mining Co. Homestake continued the drilling program and in May 1954 began sinking a 572-foot shaft and constructing a surface plant. The plant and shaft were completed in October 1954. The La Sal ore body is in the Chinle (Triassic) formation. it is tabular and dips with the enclosing beds about 8° southwest. The ore body is generally 4 to 8 feet thick but in a few places is as much as 20 feet thick it is being developed by a series of strike drifts and dip inclines, driven within the ore stratum on about 100-foot centers. A haulage level driven beneath the ore body is connected by raises to the upper workings.

Jan 1, 1957

By Frank D. Adams

The Island of Ceylon, which is one of the most beautiful possessions of the British Empire, has been an abode of man from the very earliest times. The Veddhas, a wild tribe of some 4500 people still living in the fastnesses of the jungle in east central portion of the island, are believed to represent a remnant of the oldest inhabitants of which we have any actual knowledge, but in the caves in which they live there are found the stone axes and other implements of Palaeolithic people who represent the first race of men who inhabited our globe, and of whom they may be, for all that is known, the direct descendants. About the fifth century before Christ there came the Aryan invaders, apparently from the north of India, who drove the Veddhas into the remote fastnesses of the jungle and developed the remarkable Singhalese civilization whose high character is demonstrated by the remarkable and very extensive system of irrigation works which they built up, and through which they made the island wonderfully productive. Great cities arose, some of which are believed to have had a population of over a million souls and whose temples and public buildings show that the people were accomplished architects and sculptors.

Jan 1, 1926

By R. S. Dean

This report, the second of a series of annual reports of the Metallurgical Division to be released in this form covers the fiscal year July 1, 1935, to June 30, 1936. The technological work of the division is performed by sections. Thus, an efficient organization is provided to prosecute the various problems under investigation, and a logical system is set up for presenting the material contained in this report.

Jan 1, 1937

By Wayne W. Murdy

Peru is a mineral hot spot in the world today. Newmont is in the exploratory phase of this mining cycle, a phase full of optimism and expectations. But exploration is high risk. There will be successes but also failures. Many foreign companies will come and go. But it is the responsibility of the mining industry leadership of Peru and the government to continue to foster an environment conducive to investment. This is the time of year companies begin planning their next annual report. Last year, Newmont’s was called “new horizons.” It highlighted the company’s global expansion into Peru, Uzbekistan and Indonesia. Now, projects that were only on the horizon a year ago are moving into production. So “turning opportunity into gold” may be this year’s theme.

Jan 1, 1996

This Spotlight gives a brief summary of the proposed 1991 tax amendments of relevance to mines and mining houses. It should be read together with the author's article South African mining tax in the 1990's', which appeared in the August 1990 issue of this Journal. A number of tax amendments of relevance to the mining industry were proposed by the Minister of Finance in his March 1991 budget speech. In addition, certain other measures that may be implemented were set out in the budget review document released at the same time. A word of caution is necessary: these measures will become law only if and when they are enacted in the appropriate legislation. When this legislation is tabled in June, it may not contain all of the measures discussed below, some of the measures may appear in modified form, and other measures not discussed at the time of the budget may well appear. Unless otherwise stated, the 1991 tax amendments will affect companies with years of assessment ending in the twelve-month period to 31st March, 1992.

Jan 1, 1991