Search Documents

By A. L. Engel

In previous reports5/ of ore-testing studies, teats made by established methods on typical ores selected as representative of certain mining districts have been described in considerable detail. In addition to established test procedures, such as screen analysis, Chemical analyses, microscopical examination of ores and products, sink-and-float separation, gravity concentration, floatation, and magnetic separation with or without roasting, it was sometimes necessary to apply other methods, such as leaching, in instances where physical separations were not feasible.

Jan 1, 1940

By R. F. Selden

The material in this paper is intended simply, to be an inquiry into some of the theoretical aspects of the occurrence of methane and carbon dioxide in coal, with a brief resume of the more recent literature. Several discussions on various phases of the subject have been published, a few of which (4, 20, 25, 88, 90)4/ have more or less extensive bibliographies of tie earlier literature. In large measure the pertinent literature deals with the unusual aspects of the subject, and in consequence it might appear that the normal aspects have not been given due consideration here. The latter information is largely a matter of practical field experience, and since that which is normal to one locality is often abnormal to another no sharp differentiation appears to be necessary or, in fact, possible. No attempt will be made to present a critical discussion of the relations between the presence of gases in coal and pertinent geologic features or mining practice. Although the presence of foreign gases in the ventilating air of many mines is not particularly noticeable, in many others the evolution of methane and perhaps small amounts of carbon dioxide (or sometimes the reverse - large amounts of carbon. dioxide with perhaps sore methane) is quite apparent.

Jan 1, 1934

By R. F. Selder

The material in this paper is intended simply to be an inquiry into some of the theoretical aspects of the occurrence of methane and carbon dioxide in coal, with a brief resume of the more recent literature. Several discussions of various phases of the subject have been published a few of which (4, 20, 25, 88, 90) have more or less extensive bibliographies of the earlier literature. In large measure the pertinent literature deals with the unusual aspects of the subject, and in consequence it might appear that the normal aspects have not been given due consideration here. The latter information is largely a matter of practical field experience, and since that which is normal to one locality is often abnormal to another no sharp differentiation appears to be necessary or, in fact, possible. No attempt will be made to present a critical discussion of the relations between the presence of gases in coal and pertinent geologic features or mining practice. Although the presence of foreign gases in the ventilating air of many mines is not particularly noticeable, in many others the evolution of methane and perhaps small amounts of carbon dioxide (or sometimes the reverse - large amounts of carbon dioxide with perhaps sore methane) is quite apparent. The presence of small quantities of carbon dioxide can be attributed to oxidation of the carbonaceous matter exposed to the air. In the few cases in which this explanation is not sufficient, obviously the carbon dioxide must escape as such from the coal and neighboring strata.

Jan 1, 1934

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129. The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.

Jan 1, 1931

By A. L. Engel

In previous reports5/ of ore-testing studies, tests made by established methods on typical ores selected as representative of certain mining districts have been described in considerable detail. In addition to established test procedures, such as screen analysis, chemical analysis, microscopical examination of ores and products, sink-and- float separation, gravity concentration, flotation, ,and magnetic separation with or without roasting, it was sometimes necessary to apply other methods, such as leaching, in instances where physical separations were not feasible.

Jan 1, 1940

By Donald W. Ross

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk—type sagger sponge iron, has an excellent reputation as a superior furnace feed wherever high—grade steels are made. The general procedure for making brickyard sponge iron was described frequently in Swedish technical journals prior to 1932 and at that time consisted in filling clay refractory containers, called saggers, with a super-concentrate of Gellivare magnetite plus the necessary amount of solid reducing agent and desulfurizer and then firing in a Hoffmann ring furnace, as used in the ceramic industry.The early Swedish publications describe two types of brickyard sponge iron: (1) An inferior high-sulfur product obtained by mixing the ore and reducing agent, and (2) a high-grade low-sulfur product in the form of coherent disks 7 to 9 inches in diameter and 1 to 1-1/2 inches thick made by the saggers with alternate layers of solid-fuel reducr and of uniaxed ore."

Sep 1, 1945

By Elli Nurminen

Keywords: Thermal conductivity of sulphates, flash smelting, heat recovery boiler, flue dust Accretions and build-ups in metallurgical heat recovery boilers decrease the efficiency of the heat transfer and may cause process shut downs. Transient plane source method (Hot Disk) has been applied to measure the thermal conductivities of the Copper Flash Smelting flue dusts. Thermal conductivities of copper, iron and zinc sulphates, and process flue dusts were measured. The results indicate that all the components are effective thermal insulators, having a thermal conductivity of less than 1 W/mK. Decreasing dust layer porosity has an increasing effect on thermal conductivity. Insulating layers on the boiler walls decrease greatly the heat transfer efficiency of the boiler. The gathered information will be used in CFD-modelling of the process, and in the process control.

Jan 1, 2005

By C. W. Smith

The U.S. Bureau of Mines conducted research to determine the effect of ground water control on the dewatering of phosphatic clay wastes. Two storage impoundments were constructed. One impoundment was surrounded on three sides with a series of well points (shallow vertical wells) to lower the ambient water table and the second impoundment served as a control. Ground water was pumped from the area surrounding the test impoundment for a period of 490 days. A constant pumping rate of 60 gal/min resulted in a water table drawdown of 13 ft, approximating the bottom of the impoundment. At the end of the test period percent solids in the test impoundment was 35 pct, while in the control impoundment percent solids was only 26.8 pct. Percent solids of greater than 30 pct is required for capping and final reclamation using fertile overburden.

Jan 1, 1989

By S M. Stewart

Building and Maintaining Community Relationships   In mining terms, the town of Waihi is distinctive with the Martha mine situated right in the heart of the town. MarthaÆs central location and other mining activity nearby means there is an increased community focus on the happenings at the mine and the effects and impacts of mining. While WaihiÆs proximity to the mine is unique, all mines have a community context that they operate within.   Issues of proximity simply heighten awareness and emphasise the need for building and maintaining good community relationships. In the three years we have been working alongside the Waihi community, we have worked together with concerned and supportive residents, representatives of Newmont Waihi Gold and representatives of Hauraki District Council, to develop a collaborative framework for addressing the economic, social, environmental, cultural and spiritual wellbeing of the people of Waihi. This could not have occurred without the genuine commitment of all participants.   This collaborative focus has resulted in some tangible progress in Waihi which, in part, stems from people taking an interest in the town because the town is taking an interest in itself. As we have worked and learned within the process of building and maintaining a collaborative and sustainable community environment, we have tried to adhere to a philosophy and a set of basic principles. We believe that this approach, combined with a teachable skill set, helped to create the opportunity to develop a truly collaborative community environment which continues to grow. Our paper will describe this philosophy, these principles and the skill set that we have applied.   The application of the process in Waihi has resulted in a series of outcomes unique to Waihi. These outcomes include formation of the Waihi Community Vision committee, the Vision Waihi Trust and the subgroups set up to further the interests of particular groups, for the collective benefit of all the community.   Based on our experience of other situations, and on the way the Waihi process has developed, we believe that the identified principles and skills can be transported and used in other cultures and contexts. While the resultant outcomes may differ, the underlying principles will still apply. Progress will come from creating a sustainable environment within which the community (including residents, industry and regulatory authority) can determine its own internal relationships and the vibrant growing sense it has of itself.

Jan 1, 2006

By S. A. Shuey, P. Taylor

The recycling of electronic waste (e-waste) tends to be a rather complex undertaking when considering the intimate bonding of materials in the average printed circuit board. The development of a recycling process is further complicated when considering the wide variety of products being generated under the heading of “electronics” as well as the constant change in materials of construction coupled with the speed at which electronics are changing. CSM researchers have undertaken a survey of the current state of pyrometallurgical processing of e-waste. This base-line will set the stage for the development of new recycling technology at CSM.

Jan 1, 2004

By Don L. Deardorff

The Deserado Mine and transportation system is the fuel supply portion of the Bonanza Power Plant project. Deserado Mine con¬sists of an underground mine with a capacity of 1,224,700 tonnes (1,350,000 tons) of clean coal per year, a 649 tonne (715 tons) per hour closed water circuit jig type preparation plant, a 5.6-kilometer (3 ½ -mile) overland conveyor with covered slot storage, a unit train rail load-out and 59.5 kilometers (37 miles) of totally independ¬ent, captive electrified railroad. Planning and exploration started in March of 1978. Construction of all facilities was completed in April of 1984, approximately six years after initial planning was commenced. This paper will discuss exploration, environmental permitting, mine planning, engineering and construction of the Deserado Mine project.

Jan 1, 1984

By R. Elias

Botswana is a mining-dominated sub-Saharan country. Workforces are characterised by poorly educated operators and front line supervisors, with equipment and management to 1st World standards. Poor communication, ignorance of business objectives, inability to meet targets, and lack of problem-solving capacity are the norm. Training leads to high expectations and is of concern to management as a source of dissatisfaction, despite the long-term benefits higher skills have for mine viability. The aims of a technical training programme are presented with various models and approaches being implemented at operations in Botswana. These are used to construct a series of guidelines for technical training initiatives.

Jan 1, 2000

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

By Frank C. Townsend

Waste disposal schemes using spent shale in embankments require a thorough knowledge of its geotechnical engineering properties for environ-mentally safe disposal. In this context, the objective of this laboratory investigation was to determine the physical properties, geotechnical properties, and composition of spent oil shale retorted by the PARAHO and TOSCO processes. Physical properties consisted of mechanical analyses, Atterberg limits, and specific gravity determinations. Geotechnical engineering properties were determined by compaction, maximum-minimum density, unconfined compression, triaxial compression, permeability, direct shear, Ko, cyclic tri-axial, resonant column, and Los Angeles Abrasion tests. Petrographic, chemical, and scanning electron microscopy analyses were used to determine compositional features. Unprocessed shale is hard and durable and more properly described as a carbonate rock instead of shale. PARAHO is classified as a GP, while TOSCO classifies as an SM. PARAHO requires no moisture for compaction to maximum densities; however, TOSCO does. Retorting causes a loss in durability but creates self-cementing characteristics, which for PARAHO a 3-to 8-fold strength increase was observed, while for TOSCO the increase was 1.5 to 3 folds. The shear strength, compressibility, and dynamic properties of compacted PARAHO are comparable to those for sandy gravels. Compacted PARAHO is semipervious, while compacted TOSCO can be semipervious to impermeable.

Jan 1, 1979

By R. Larry Grayson

In the October 1998 issue of the Holmes Safety Association Bulletin, NIOSH authors Mark Stephenson and Carol Merry wrote the article Hearing loss among miners and measures to protect hearing, which focused on the extensiveness of hearing loss among miners and the use of hearing protection to prevent hearing loss. While the primary importance of engineering controls in preventing hearing loss was discussed, since miners do not generally have control over their work en­vironment or assignments, the article focused on the importance of consis­tent use of hearing protection. In this article, all aspects of a compre­hensive approach to the prevention of hearing loss in miners will be covered. The discussions will do the following: ? describe application of the hierarchy of controls in preventing hear­ing loss in miners, ? give an example for each type of control measure and its impact, ? explain the major provisions, be­yond the hierarchy of controls, of the recent NIOSH document en-titled Criteria for a Recommended Standard: Occupa­tional Noise Exposure, Revised Criteria 1998 relative to a hearing loss prevention program, and ? summarize important points on control of noise exposure for every miner to remember, equipment in most facets of operations. Miners are well aware of noisy areas in or around equipment, icluding extraction machinery such as draglines, power shovels, longwall shearers, and continuous mining machines; powered haulage equipment such as load-haul-dumps, shuttle cars, large trucks, and continuous haulage units; roof bolting machines; jackleg drills and stopers; auxiliary equipment such as compressors, fans, and pumps; size reduction equipment, etc. They are not well aware of the insidious nature of pro­gressive hearing loss, which is per­manent, but they are generally aware of what levels of noise are hazardous and what measures can be taken to reduce their personal noise exposure. Behaviorally, however, there are many reasons why miners choose not to use hearing protection faithfully.

Jan 1, 1998

By A. R. Byers

"This paper describes the distribution, occurrence, and paragenesis of known sulphide deposits within an area bounded by longitudes 102°00' to 106°00' west and latitudes 54 ° 301 to 57 °00 1 north. The Precambrian bed-rock which outcrops over all but the southern fringe of the area con- . sists of regional metamorphic assemblages ranging from low grade or green schist facies to high grade or amphibolite-granulite facies. The areas . of low-grade metamorphism correspond to 'islands' of volcanic rocks which are surrounded by highgrade paragneisses and migmatites. Intrusive rocks range in composition from ultrabasic to granitic and may be divided into syntectonic and posttectonic sequences. The average composition of the former is granodiorite and of the latter quartz diorite.The massive sulphide deposits fall naturally on basis of mineral content into the following divisions: ( 1) pyrrhotite and / or pyrite, (2) sphalerite and/ or chalcopyrite plus iron sulphides, (3) sphalerite and galena, ( 4) sulphide-bearing pegmatite, and (5) nickeliferous pyrrhotite and / or chalcopyrite. The deposits of iron sulphides are ubiquitous. Ratio of pyrrhotite to pyrite is fairly constant for individual deposits, but their areal distribution appears to be independent of the nature of the enclosing rock and grade of regional metamorphism. All deposits containing ore-grade quantities of base metals have been concentrated at favourable structural locations. Copper-zinc and lead-zinc deposits appear to be associated with syntectonic granodiorite with the lead-zinc concentrations confined to calc-silicate gneisses. Copper-nickel deposits show a close relationship to post-tectonic gabbros and pyroxenites. The paragenesis is more or less the same for the majority of deposits, with iron sulphides and sphalerite being introduced early and followed by chalcopyrite and galena. Some vertical and / or horizontal zoning is apparent in a few deposits. Temperatures of formation and origin of the deposits are briefly discussed."

Jan 1, 1960

By Jeffrey Y. Foley

Chromite deposits along the Border Ranges Fault in southern Alaska were investigated by the Bureau of Mines. This report, part 1 of a two- part series, describes the deposits. Part 2 describes the mineralogy and the results of metallurgical tests. Fieldwork began in 1981 and continued through 1983. Ninety-four subeconomic podifom chromite deposits in eight mafic-ultramafic complexes were investigated. Previously unreported chromite deposits at Red Mountain on Kenai Peninsula, on Kodiak Island, and near Tonsina are described. Deposits range in size from less than a thousand tons to over 1.25 million tons of contained chromic oxide (Cr203). Grades range from about 5 to 10 pct chromite. Excluding all deposits more than 10 miles from tidewater or existing roads and all deposits containing only chemical- or refractory-grade chromite, about 2,200,000 tons of Cr203 are contained in 41 hard-rock deposits. A placer deposit contains an additional 556,000 tons. These 42 deposits constitute a subeconomic indicated and inferred reserve sufficient to meet the Nation's chromite demands for about 4 yr, or the metallurgical industry's demands for over 5 yr, at 1981 consumption rates.

Jan 1, 1985

By R. F. Zaffarano

Reservoir oil in the Greater Aneth area, Utah, part of the Paradox basin, was studied to detect variation in oil characteristics within the reservoir and to determine its relation to age of accumulation and fluid equilibrium. At least three subsurface oil samples were obtained from each of the four largest of five field divisions comprising a producing area of 45,000 acres. Height of the oil column in the Pennsylvanian Desert Creek zone is about 230 ft. In general, the oil characteristics were found to be uniform across the area, and averages were developed for use in engineering applications. Average saturation pressure was 1,780 psia; the oil was undersaturated at the initial reservoir pressure, 2,200 psia. Variation in saturation pressure shows a lack of complete fluid equilibrium and continuing diffusion of solution gas from the main body of the reservoir to two extensions linked by narrow arms. By assuming early accumulation, the time involved in this diffusion process was calculated to be about the same as the age of the reservoir formation. Cause of the concentration of gas in the main body is attributed to differential entrapment during accumulation of oil and gas from an exterior source.

Jan 1, 1963

By R. M. Creamer

Attempts have been made to electroplate titanium and zirconium from aqueous, nonaqueous, and fused-salt electrolytes. Metals were produced only in fused-salt electrolytes, the major product being sponge metal. All other electrolytes gave only partial reduction of the metal ions. Fused alkali borate electrolytes containing titanium salts gave titanium boride powders and coatings of poor adherence. Some of the problems encountered in the deposition of these metals and some of the aspects of titanium and zirconium chemistry involved are discussed. INTRODUCTION Titanium and zirconium are both relatively light, noncorrosive metals with both military and civilian uses. This has led to intensive investigations into the metallurgy of these metals. Both metals are high in the Electrochemical Displacement Series and are difficult to prepare in a pure state. At present they are prepared by reducing their chlorides, using magnesium. Electrolytic reductions have resulted in the preparation of fine powders or sponge of variable quality. It is believed that a good process of electroplating these metals on a baser metal would result in a very desirable product. The objective of the research summarized in this report was to investigate methods of electrodepositing these metals, with the idea of producing uniform, coherent plates. Most of the work was concentrated on titanium, the more abundant of the two metals. A system developed for titanium should be applicable to zirconium owing to their chemical similarity. Information gained from these experiments may also be applicable to the electro-winning of the metal.

Jan 1, 1954

By C. J. Hall

Twenty eight pulse release sulfur hexafluoride tracer gas field tests were run in a multi-level multi-vein hard rock mine to measure leakage ventilation. The mine had numerous underground booster fans and gob filled old stoping areas and consequently numerous leakage paths. The tests proved that the equipment and methods developed by the USBM can be used successfully in complicated ventilation circuits. The leakage quantities varied each time a major change was made in the main ventilation circuit. Usually leakage quantities had to be remeasured after a main ventilation change, but measurements could be duplicated for anyone configuration except under certain defined circumstances. The characteristics of an individual leakage path could be determined from the difference between the measured sum of two paths and the calculated characteristics of one of the paths. Many leakage paths could not be evaluated accurately on one shift. Comments are made on equipment performance and field techniques. Programs for the calculation of gas concentrations and recirculation from measured data and for the mechanical integration necessary for a calculated leakage characteristic have been written for an HP 9810 and are included.

Jan 1, 1975