Search Documents

Jan 1, 1961

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Downstream processing of these mineral fuels to petrochemicals and fertilizers is a major investment opportunity. In 1991, the 15 countries that constituted the region accounted for 26 % of world crude petroleum output, 15.3 % of world natural gas plant liquid production, and 4.5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Production of these mineral fuels all declined from that of 1990 owing to the Persian Gulf War, during which output from Kuwait and Iraq either ceased owing to war damage, or was embargoed. Prior to the war, Iraq and Kuwait were the fourth and fifth largest world producers of crude petroleum, respectively. In the war, virtually all of Kuwait&apos;s production and transport facilities were destroyed or damaged. Iraq&apos;s output was embargoed from export, with only domestic sales taking place. The embargo also affected Jordan, both in terms of transshipment of materials through it to Iraq and in exports of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion, increasing crude petroleum output by 27 % to almost 3 billion barrels.

Jan 1, 1993

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By Kelvin K. Wu, George H. Gardner

On July 24, 2002, a nonfatal entrapment accident occurred at the Quecreek #1 Mine, Black Wolf Coal Company, when an active mining section inadvertently cut into a flooded abandoned mine. This incident, and the dramatic rescue which ensued, brought national attention to a common problem in the coal mining industry. Since 1995, there have been more than 100 inundations at coal mines in the United States. Unavailable, inaccurate, or incomplete mapping of older abandoned mines is typically responsible. Serious problems associated with accidental discharges of fluid mine waste material (slurry) and water from coal refuse disposal facilities have resulted from similar causes. Recent problems related to the inaccurate location of old abandoned mine works have increased the interest in the use of conventional and emerging drilling and geophysical techniques for detection of air-filled and water-filled cavities. The United States Congress has committed significant funding toward investigating the applicability of these technologies. MSHA actively promotes the use of the best available technology to minimize the significant adverse safety and environmental consequences associated with unplanned breakthroughs and inundations. This paper provides background information and a general summary of the MSHA-sponsored field demonstration projects which are currently in progress. Potential benefits and limitations are discussed. The need for field verification/ground-truthing is emphasized. Under appropriate conditions, geophysical methods can be effectively integrated into a comprehensive field exploration program.

Jan 1, 2005

Executive SCOTT TURNER, Chairman FREDERICK M. BECKET JOHN A. MATHEWS H. A. GUESS WILLIAM WRAITH Finance HENRY KRUMB, Chairman PAUL D. MERICA ROBERT E. TALLY Admissions JOHN M. LovEJOY, Chairman GEORGE D. BARRON ERLE V. DAVELER WILLIAM H. BASSETT W. D. B. MOTTER, JR. Alternates HENRY B. FERNALD F. JULIUS Polls AMOR F. KEENE

Jan 1, 1932

By K. H. McDaniel, D. M. Loring

The underground ventilation system at the Waste Isolation Pilot Plant provides unparalleled ability to ensure safety of the workers, public and environment. Although small spatially, it can vary the airflow from 66,000 acfm to 460,000 acfm. It can automatically incorporate HEPA filtration in the event of radioactive contamination. Remote-capable regulators individually control the four main splits, and can be adjusted from the surface if necessary. A ventilation remote monitoring and control system provides real-time information. Future areas of concern include DPM compliance, system psychrometry, logic-based-real-time mine ventilation simulation and automation using PLC technology. This paper discusses the evolution of this system.

Jan 1, 2002

By Larry R. Fletcher

A misfire results when explosives fail to detonate as planned during a mine blast. Accidental detonation of misfires is a frequent cause of personal injury, equipment damage, and lost production. In an effort to minimize these problems, the Bureau of Mines investigated the causes of misfires, methods for detecting misfires, and procedures for their disposal. During this investigation, input was obtained from explosives suppliers, mining companies, blasting contractors, blasting consultants, and governmental agencies. Additional data were obtained through detailed analysis of blasting accidents involving misfires.

Jan 1, 1983

By J Morton

The Resource Management Act 1991 represented an innovative and unique piece of planning and environmental legislation when it was introduced. Since the Act was passed into law in 1991 it has been subject to nine amendments, many of which were of the ætinkerÆ variety. These amendments recognise that the Act has not been as successful in providing the æone-stop shopÆ for resource users that the Act was hoped to be. The latest and most significant attempt at changing the Act was the Resource Management Amendment Act 2003. The amendments made by the Amendment Act have proved to be largely unsuccessful in achieving any significant changes to the way resources are managed in New Zealand, and have failed to address many of the concerns which drove the original Resource Management Amendment Bill in 1999. The recent decision to discontinue further investment in Project Aqua has once again placed the Act in the spotlight as a significant hand-brake on major projects. This particular event has led to yet another review to be undertaken this year. The review will focus on five key areas: &nbsp; 1.&nbsp;&nbsp; achieving the right balance of national and local interests; 2. &nbsp; improving the design and process for local policy formulation; 3. &nbsp; improving the consent decision making process; 4. &nbsp; allocation of natural resources (water, air and geothermal); and 5. &nbsp; supporting measures for building capacity and promoting best practice and implementation at the local authority level. &nbsp;It is important for the business community and the mining industry in particular to seize the opportunity that this review provides to make sure that any amendments undertaken as a result of the review achieve the aims listed above. The review needs to be considered in light of the current regime for the management of natural resources in New Zealand. In addition to the Resource Management Act 1991, the Crown Minerals Act 1991 and the Building Act 1991, which form the core resource statutes in New Zealand, there have been other developments affecting the regime. Special legislation over and above the Resource Management Act 1991 has been enacted to protect the Hauraki Gulf and special legislation is currently being considered to protect the Waitakere Ranges in Auckland. In the Hauraki District mining is prohibited in some areas and a plan change mechanism is specified as the appropriate tool to use in the event a mineral resource is to be developed in those areas. The current review is a further opportunity to remedy the inadequacies of the Act.

Jan 1, 2004

By Chikabumi Yamauchi

The comprehensive scientific development of conventional industrial technologies stimulates the creation of new ones in the next generation. Prof. Akira Yazawa has just accomplished such an important work in the non-ferrous pyrometallurgical field. The results of his successful research are immortal. The research group of the author has conducted since 1985 fundamental studies on the application of sodium carbonate slag to copper fire refining. In the present paper, a calculation method for the distribution ratios of impurity elements between sodium carbonate slag and molten copper will be shown. The specific treatment by sodium carbonate slag will also be presented as an effective way for reducing each impurity content in the molten copper to 0.1 mass ppm, which is the level required for the production of high purity copper. The thinking-out of this evaluation method gets a hint from the Equation (2) in the text which was proposed by Prof. Akira Yazawa.

Jan 1, 2003

By T. R. Jolley

This publication describes the control of fires in inactive coal deposits in the Western United States, including Alaska by the Bureau of Mines. Material presented should contribute to a better understanding of the purpose, process, and benefits of the program. Forty fires were extinguished or controlled in the Western United States and Alaska from 1948 to 1958 under a national program directed by the Bureau&apos;s Health and Safety activity. Thirty-five fires were controlled by smothering; three were controlled by the isolation method; and two were extinguished by removing the burning coal, smothering it with incombustible material, and backfilling the fire zone. The fire-control projects were distributed as follows: Alaska 2, Arizona 1, Colorado 9, Montana 9, New Mexico 4, Utah 2, and Wyoming 13. The total cost of the 40 fires extinguished or controlled was $1,203,957. Of this cost, 12.8 percent was engineering and administrative and 87.2 percent was contractual services.

Jan 1, 1959

By Alice Turcot

Knowledge of risks from exposure to hand-arm vibrations is usually presented by clinicians and researchers from a medical and engineering point of view. There is a strong need to develop innovative health promotion programs for exposed workers. Risk perceptions by vibration exposed workers and HAVS (hand-arm vibration syndrome) affected workers are less well known. In 1983, Brubaker demonstrated that 75% of studied fellers thought that whitening of the fingers was part of the job and/or an unrelated nuisance, while only 25% believed it was a disease. 1Grounds also showed that even though there were a very high number of forestry workers with white fingers, none considered quitting because of their condition. 2 It seems that many workers hesitate to declare the illness or believe they are less affected than they really are, perhaps from fear of losing their jobs and livelihood. 3 Risk awareness, on the part of exposed workers and their employers, as well as knowledge and acceptance of available preventive solutions are necessary steps before installing adequate preventive measures, whether organizational, behavioral or environmental. Workers need to understand fully the hazards and risks in order to be able to make informed decisions under uncertain conditions.4 Prerequisites include the following: workers knowledge about the risk, their attitude towards it, which in turn, can be influenced by values, needs and interests. Also, knowledge and attitudes towards safety behaviour, organizational or environmental barriers must be taken into account. Our research focuses on these key elements, which help bridge the gap between health promotion research and practice. Methods A descriptive exploratory study is in progress with workers exposed to hand-arm vibrations. It uses qualitative methods that include focus group discussions with workers exposed to hand-arm vibrations, as well as individual interviews with other key informants (employers, health care professionals). An open-ended questionnaire was developed to collect qualitative data on perceived risks and solutions to prevent or reduce HAVS. Based on an integrated theoretical framework related to known determinants of behavior change, the analysis will focus on the following5: 1) knowledge of health effects, safety, well-being and/or quality of life 2) related beliefs about individual susceptibility and severity of consequences 3) attitude and values related to hand-arm vibration exposure 4) knowledge and attitudes towards exposure reduction, as well as perceptions of barriers and facilitating factors for these measures, in the workplace environment or otherwise.

Jan 6, 2006

By G P. Bates

The rationale for the design of the Emergency Egress (escape andentrapment) strategy for one underground metal mine has beenpreviously described (Brake, 1999). Two of the key conclusionsfor this mine, which is equipped with 30 minute oxygen-generating self-contained self-rescuers (SCSR), were the need to ensure no person is ever more than 750 m from an emergency refuge station (ERS) and that it could take up to eight hours to rescue workers from undergroundå. These conclusions were based on a number of considerations including the non-availability of a credible, æpersonalÆ entrapment procedure at the workplace, the duration of self-contained self-rescuers when used for travel, the need for rapid æclearingÆ of mine personnel to effectively and safely target mine search and rescue resources and the maximum time to either put a fire out, or to rescue affected personnel. As there is no Australian standard for refuge stationsç (or for self-rescuers), this paper follows with guidelines for the location and specification of both fixed (permanent) and relocatable Emergency Refuge Stations (ERSs) that may be applicable to other underground Australian metal mines.

Jan 1, 1999

By E. R. Macgregor, J. Halpern

The kinetics of the reduction of cupric salts in aqueous solution by molecular hydrogen to metallic copper are described. The rate of reduction appears to be homogeneously determined and shows a marked inverse dependence on the hydrogen-ion concentration. Precipitation of copper is more rapid and complete in sulfate than in per-chlorate solution. A mechanism is proposed which accounts for this behavior. IN recent years a number of important hydro-metallurgical processes have been developed in which metallic salts in aqueous solution are reduced by gaseous hydrogen, usually at elevated temperatures and pressures, and thereby precipitated either in metallic form (e.g. Ni, Co, Cu) or as an oxide or salt of lower valence (e.g. VO, and VA).1 ; In connection with applications such as these, most of which involve heterogeneously catalyzed reactions, recent demonstrations"-" that salts of certain metals, e.g., Cu", Ag&apos; , Hg" , and Hg,+ can activate molecular hydrogen homogeneously and thus catalyze hydrogenation reactions in aqueous solution, are of considerable interest. For example, cupric salts catalyze the otherwise slow homogeneous reduction of dichromate and ceric salts by hydrogen, i.e. Cr,O; + 3HL. + 8H1 ? 2Cr&apos;- -- 7H,O [1] 2Ce &apos; ! H.. ? 2Ce" | 2H . [2] In perchloric-acid solution, where Cu" is not appreciably complexed, the kinetics have been found" " to be of the form -d [H,] _- k,[HJ [CU"]&apos; dt -LCu+&apos; l+ (k ,/k,) [H] [3] where, K = 1x10"&apos; exp [—26,600/RT] 1, mole-&apos; min-&apos; ... [4] and (k ,/k,) - 0.25 at 110°C. This kinetic behavior suggests that the reaction proceeds by a mechanism involving the following sequence of steps kt Cu" +H1CuH&apos; 4-HA [51 k., CUH + CU" ? + 2Cu f H&apos; [GI 6Cu&apos;+ Cr,07 + 14H&apos;+ 2Cr- (¦ 7H,O + 6Cu" [&apos;i] fast The catalytic activities of the undissociated cupric-sulphate and cupric-acetate complexes are somewhat greater (by factors of 6.5 and 120, respectively) than that of the simple hydrated Cu" ion.&apos;" These considerations suggest that, in contrast to the other hydrometallurgical hydrogenation reactions, referred to previously, reduction of cupric salts in aqueous solutions by molecular hydrogen, should proceed homogeneously, and in the absence of an extraneous catalyst. This has already been demonstrated" for acetate-buffered solutions where the product of the reaction is a precipitate of cuprous oxide (Cu,O). In the present paper, an investigation of the reduction of cupric salts in perchloric-acid and sulphuric-acid solutions, leading to the precipitation of metallic copper, is described. Some results for the sulphate system, which is of considerable hydrometallurgical interest, have been reported previously by Ipatieff",&apos; " and by Schaufel-berger&apos; but these do not give a quantitative account, of the kinetics and mechanism of the reaction. Experimental The reduction experiments were conducted in the 1-gal, titanium-lined autoclave described in connection with earlier related investigations," " and using a similar procedure. The solutions were made up by dissolving known amounts of CP grade Cu(ClO,), and HC10, (or CuSO, and HISO,) in dis-tilled water. While in the autoclave, the solution was stirred and maintained at a constant temperature (±loc) and under a constant partial pressure of hydrogen gas. It was ascertained that the agitation (provided by two 3-in., four-bladed stirrers, rotating at 900 rpm) was adequate so that at no time was the rate of reaction limited by solution of hydrogen. During each experiment, samples of the solution were withdrawn periodically, allowed to cool, and the concentration of copper remaining in solution was then determined electrolytically. Some Cu&apos; is formed during the reaction, but undergoes disproportionation when the solution is cooled to room temperature. For purposes of kinetic calcula-

Jan 1, 1959

By Andrew Wessman

Keywords: Recycling, Electrodeposition, Recovery, Dilute, Dissolved Metal Ions In order to facilitate the recovery of pure metals from solutions containing a mixture of dissolved metal ions, a pulsed electrodeposition method was developed. Using this method, it is possible to selectively remove metal ions from solution based upon the electrochemical potential of the particular ion desired. The use of pulsed electrodeposition rather than direct current electrodeposition creates an electrodeposited material with better morphology, increases electrical efficiency of the process, and avoids problems with short circuiting between electrodes. Using this method, it is possible to recover dissolved metal ions in a purified form in one simple step, and therefore maximizes recovery of the metal ions while obtaining them in a saleable form. This method is likely to be useful in improving the recycling process for numerous complex metal mixtures and alloys.

Jan 1, 2005

By Lloyd Robert Nelson

The historical progression in installed electric furnace smelting capacity of some 1650 calcium, chromium, manganese, nickel and silicon ferro-alloys furnaces is reviewed. Key increases in the inherent installed electrical capacity, often achieved through uprating furnaces, are identified. Possible factors facilitating such advances are explored, including: specific process engineering and pyrometallurgical enhancements (e.g., improved control over the consistency, size and chemical form of raw materials, extents of preheating and pre-reduction delivered into the furnace; and patterns of feed distribution); furnace electrical configuration (AC or DC; immersed, submerged-, shielded- or open-arc); form of electrode (graphite, self-baking or composite); furnace configuration (circular or rectangular; closed or open and 1-, 3- or 6- electrodes); better engineering and equipment designs (e.g., high-intensity cooling) and state of furnace electrical and metallurgical control systems. A view is presented on the prevailing state of evolution of the Mega-scale in ferro-alloy smelting and opportunities for still further improvements.

Jan 1, 2014

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.&apos; In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By Russell Levens

A strategy for prioritizing mining health and safety research by evaluating the potential for risk reduction through interventions is proposed. Mining has one of the highest incidence rates of injury and disease found in major industries. The main premise of this paper is that often the best opportunities to reduce these rates are not revealed by retrospective analysis of injury and illness data. Instead, a proactive approach is needed that accounts for risks to specific hazards that can be abated by engineering or behavioral interventions. The process proposed here begins with development of prospective interventions. The degree of reduction in risk to be expected from an intervention then is determined from statistics on the mining worker population, the expected degree of success of the intervention, and the expected change in the severity of injuries resulting from the intervention. Three disparate mining health and safety concerns are presented to demonstrate common problems in assessing risks of injury and illness and describe additional data needs. Information on events preceding injuries and illnesses and more detailed demographic data on the mining work force are needed to analyze injury and illness data more precisely. Detailed information on exposure to specific hazards is necessary to evaluate the potential for an intervention to reduce risk of injury or illness.

By Melissa L. Trapani

Keywords: Copper, Taphole, Flow Instability. ?Blister spitting? is a flow irregularity where the molten blister copper stream ? or part thereof ? sprays from the taphole exit rather than following a regular flow profile to the collection box. As well as being a general ?housekeeping? issue, the unpredictable nature of the flow is a threat to operator safety. Also, the aggressive flow pattern may contribute to the mechanical wear of the taphole refractory, compromising the integrity of the taphole. This paper brings together a collection of first-hand observations and reports from process personnel, and suggests some theories as to the causes of blister spitting.

Jan 1, 2005

Mr Colin M. Spence took office as President of The Federation of Societies of Professional Engineers on 1st July, 1984. Colin Maynard Spence was born in November 1921, and was educated at the Durban Preparatory and High Schools, in both of which he was a Dux Scholar. He graduated from the University of Natal in 1942 with a B.Sc. degree in civil engineering. In 1958 he received a Diploma in Town Planning from the same university. Cessation of Membership In accordance with Clauses 7.6.1 and 12.1 of the Institute&apos;s Constitution, Rules and Policy, the following members have been struck off the Membership list.

Jan 1, 1984