Search Documents

By Alastair Torrance, George Boucher

The authors were involved in the Trial Blast work at Chek Lap Kok, the site of the new Hong Kong Airport. As part of that work a series of computer programs including 3x30, QFRAG, DESIGNER and 3DMUCK was employed to predict various aspects of the trial blast programme. These aspects included fragmentation and muckpiie shape. This provided an excellent opportunity for these programs to be calibrated, verified and compared under controlled conditions. The results indicated that computer simulation has reached a high level of sophistication and good correlation between prediction and measured results was found.

Jan 1, 1994

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002

By Donald Markle

ANTHRACOAL is a mixture of small particles of anthracite coal and a matrix of practically pure carbon, formed from the distillation of coal-tar pitch or other suitable bitumen. It is a hard, dense, homogeneous mass, with a silvery luster and in color varies from silvery to grayish black. When pushed from the oven, it develops only partly the fingerlike structure of coke; but, unlike coke, it has a tendency to remain in blocky masses. When struck with a hammer or passed through crushing rolls, it breaks with an irregular fracture, similar to anthracite, but with very little fines. Due to its density, anthracoal is harder, tougher, and stronger than coke. The results of a test made by the blast-furnace department, of the Bethlehem Steel Co., on two barrels of anthracoal are given in Table 1. TABLE I.-Results of Shatter Tests on Anthracoal and Coke Anthracoal Test Good Blast-furnace Coke First Second Barrel Barrel Moisture, per cent 0.77 0.76 Under 5, variation not over 3 points Sieve test Through 2-in. screen, per cent 7.71 7.29 Under 40 Through 1-in. screen, per cent 1.37 1.56 Through ½ -in. screen, percent 0.93 1.08 Under 8 Over 2-in. screen, per cent 92.29 92.71 Over 60 Shatter test Through 2-in. screen, per cent 10.06 ' 12.40 1 Under 16 Through 1-in. screen, per cent 2.66 2.06 Through ½ -in. screen, per cent 1.80 1.26 Over 2-in. screen, per cent Hardness number 86.40 86.10 Over 81 Analysis Ash, percent 16.64 16.48 Under 11 Sulfur, per cent 1.17 1.10 Under 0.95 Volatile matter, per cent 0.77 0.27 Fixed carbon, percent 82.59 83.25 Over 87

Jan 8, 1921

By John J. Henn

An evaluation is presented of the Bureau of Mines process for the recovery of metal and mineral values from municipal incinerator residues. This process employs standard mineral beneficiation techniques and is operating on a pilot-plant scale of 1,000 pounds of incinerator residue feed per hour. Products from this separation process include ferrous, aluminum, and copper-zinc scrap, and colorless and colored glass. Cost estimates were prepared for four plant sizes. The estimated capital and operating costs For the four plants follow: [ ] It is assumed that the separation plant is located adjacent to a municipal incinerator. Provision is made, however, for part of the residue feed to be delivered by truck so that one large separation plant can be used for residue from more than one incinerator.

Jan 1, 1971

Jan 1, 1891

Jan 1, 1961

The State of Washington has a federal program that gives the Office of Surface Mining responsibility for assuring the reclamation of lands affected by coal mining. Most of Washington's coal-bearing regions lie west of the Cascade Mountains. The state's coal reserves are estimated at 1.4 billion tons, about 0.3 percent of the nation's total coal reserve. Steeply dipping. minable seams range from 2.5 to 25 feet in thickness. The occurrence of coal in Washington has been documented since the early days of its settlement; at one time, coal production played a significant role in the state's economy. During the late 1800s and early 1900s, coal was second only to lumber in Washington's industrial production. Coal production declined as other sources of energy were developed. By 1959, production was at 200,000 tons. Regulation of the coal mine operations in Washington is conducted by the Office of Surface Mining's Casper, Wyoming, Field Office and its local office in Olympia, Washington. All permit applications and abandoned mine land reclamation are completed by the OSM Western Support Center in Denver, Colorado. Inspections of mine and reclamation sites are conducted by OSM reclamation specialists located in Olympia.

Jan 1, 1992

By G. V. Campbell, O. T. Holdsworth, M. G. Nelson

A senior design project is required by all accredited mining engineering degree programs. Often referred to as the capstone of a student’s education, this project is expected to include all the important components of the preliminary economic assessment of a mineral prospect, including orebody modeling, grade and reserve estimation, selection of mining and processing methods, preliminary mine design, access and utilities, environmental compliance and reclamation, and financial analysis. Two of the authors (Campbell and Holdsworth) completed a senior project in 2021. They analyzed the Akie zinc deposit located in Canada. This paper summarizes the economic analysis portion of that project. The two primary objectives of this economic analysis were risk reduction and integration of economics and engineering. Addressing risk is important as risk is one of the primary concerns in mining investments. Risk reduction was the primary concern through the entirety of this economic analysis. Integration of financial analysis and engineering design was the first component of a risk reduction design. This allowed for financial and engineering design to be optimized in conjunction with one another. This produced benefits from both a financial and an engineering prospective. From a market, economic, and financial risk perspective, risk was reduced by forecasting multiple metal price scenarios, and then addressing the Akie project’s economic viability at each price point. Lastly, risk was address through consideration of nontraditional financing options. The project also sought to minimize financial and human capital risk, by proposing mutually beneficial cooperative social relationships and favorable work, schedules. Description of that work is not included in this paper.

Mar 2, 2022

The ERMS Process was developed during four years of testwork by Austpac Gold NL to overcome the severe metallurgical problems of the ilmenite atWestport, in the South Island. These deposits have been known for about one hundred years. They were originally mined for gold, and only later attracted attention as a possible source of titanium minerals.   The resource is of world scale and may exceed 20 million tonnes of contained ilmenite. Similar deposits occur at Barrytown further south and together these areas would constitute an important opportunity for export-oriented mineral development, if a viable beneficiation technology were available. Further processing is essential, as the composition of the ilmenite is well below market specifications.

Jan 1, 1993

By Yuri D. Tretyakov, Robert A. Rapp

The stoichiometry ranges ofNiOl+y and LiFe,O,-d were established by high-temperatwe electrochemical meas7rements in a stabilized-zirconia electrolyte cell. The results were consistent with doubly ionized cation vacancies in NiO,+y and interstitial lithium or iron ions in . The defect structure of the ternary ferrite was derived from the consideration of equilibration with respect to oxygen between the solid and the gas phase. The absolute magnitudes of defect concentrations were calculated. Pavtial molar enthalpies of oxygen in the compounds were calculated and interpreted in terms of the enthalpy of defect formation in these crystals. NICKEL oxide (NiO,,?) is a metal-deficient, p-type, extrinsic semiconductor whose properties are consistent with a structural model based on the presence of cation vacancies as the predominant ionic defect at sufficiently high temperatures and oxygen activities. A survey of previously reported conductivity studies and the presentation of some more recent conductivity measurements will be given in a later paper.' The absolute magnitude of the equilibrium vacancy concentration in NiO has been reported from combined conductivity and thermogravimetric data of ' However, disagreement exists concerning the state of ionization of the nickel vacancies in NiO. Some authors3-' have proposed that the predominant defects in NiO are singly ionized nickel vacancies and positive holes (h') formed by the reaction where, accorhng to the notation of Kroger and Vink,6'7 Oq represents an oxygen ion on its normal lattice site. Other authors"27E have proposed that doubly ionized nickel vacancies (V{i ) and positive holes are predominant and are formed by the reaction One purpose of the present investigation was to establish the nature of the predominant defect in NiO,+? as well as its equilibrium concentration and thermo-dynamic properties at elevated temperatures and known oxygen activities. To accomplish this purpose, the coulometric titration of oxygen into and out of NiO was accomplished using a galvanic cell involving the calcia-stabilized zirconia electrolyte. The ternary oxide, lithium ferrite (LiFe50,-6) is ferromagnetic and has the inverse spinel structure LiFe,O,-d Thus, in the ideal stoichiometric XY204 lattice, Fe3 ions occupy one-eighth of the tetrahedral (A) sites, and i' and Fe3' ions share at random one-half of the octahedral (B) sites within the fcc sublattice of oxygen ions.g The structure and thermodynamics of the spinel structures have been comprehensively decribed.'-' A recent compilation of literature for lithium ferrite is also available. 15 Oxygen-excess LiFe50sis not expected to exist because both i' and 17e3& ions are in their highest normal valency states (positive hole formation is not favorable). As will be discussed, equilibration of the ferrite crystal with oxygen of a surrounding gaseous phase will result in the introduction of equilibrium concentrations of ionic and electronic defects. In the Results and Discussion section a defect model for LiFe50,-d is proposed. This defect model is tested by high-temperature coulometric titration experiments. EXPERIMENT The oxygen activities in nonstoichiometric NiOl+, (and also LiFe,O,-d) were measured by means of coulometric titration with the high-temperature galvanic cell The critical characteristic of a suitable experimental cell is the complete isolation of the phase to be investigated in a minimum sized chamber which is free from extraneous sources and sinks for oxygen (leakage). Then oxygen is only admitted to the chamber or removed from it in known amounts by coulometric titration, which involves the passage of oxygen ions through the solid electrolyte with electrochemical oxidation and reduction reactions at the platinum contacts to the electrolyte. The experimental cell is shown in Fig. 1. The cap of the cell was the tip from a closed-end alumina tube, which was found to be leak-free from a helium leak-detector test. This alumina cap was about 1.2 cm OD and about 1.5 cm high. A Zircoa calcia-stabilized zirconia tablet (crucible lid) of 1.5 cm diam and 0.3 cm thickness served as the solid electrolyte. A Pyrex ring of about 0.1 cm thickness was placed between the electrolyte and the cap. The electrolyte tablet was painted with platinum paste on the entire outer face and on that part of the inner face which would be within the enclosure; these electrodes were further prepared by heating in air at 1000°C for 2 hr. Nickel oxide powder, listed as 99.999 pct pure, was purchased from Leico Industries, Inc. Pills of the NiO were cold-pressed and sintered at 1050°C for 3 hr in a platinum crucible. This poorly sintered NiO was crushed, and chunks were wrapped in 52-mesh Pt gauze (to catalyze the solid-gas exchange) for place-

Jan 1, 1970

By S Christensen

In August 2001 the Minister for Conservation declined an application by GRD Macraes for an access arrangement to enable work at the Globe Progress Mine near Reefton. In her decision, Ms Lee said:æI have considered whether potential compensation and the proposed safeguards against some of the adverse effects are sufficient to outweigh my concerns as to the loss of conservation values, consistency with the objectives of the Conservation Act, the purposes for which the land is held by the Crown and, to a lesser extent, the North Westland Regional Management Plan. I do not think they are sufficient. To my mind, my concerns as to the consistency with the objectives of the Conservation Act, the purposes for which the land is held and the loss of some conservation values in particular, outweigh any potential compensation and possible mitigation of adverse effects.Æ Commenting on the MinisterÆs decision Guy Salmon of the Ecological Foundation stated that the Minister should have invited the applicant to provide a 10 000 hectare pest-free wildlife sanctuary as part of the æpriceÆ for obtaining that access. However,æfor many people of green persuasion, it has become fashionable to say no every timeàthose who really have the well-being of the environment at heart, will want to look carefully at the bigger picture of environmental restoration needsàThe deciding criterion: the mining company should show that its involvement on conservation land would produce a net conservation gain. That is a criterion that creates the right incentives for win-win-win solutions on conservation land.ÆThis paper considers whether the concept of off site mitigation is one which fits within the current legal regime. Two questions arise:Can such mitigation/compensation be legally considered in access arrangements or required as a condition of resource consents? Is this a realistic option for industry to be pursuing?

Jan 1, 2002

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

By Michael P. Sudbury

Non-ferrous slags are granulated and stockpiled as an alternative to pit cooling or transporting molten slag to a dump. The chemical composition of such slag is determined by the pyrometallurgical process in which it is produced, while the size distribution is set by safety concerns or a desire to reduce wear of pumps, pipelines and other equipment. Relatively few operations give consideration to the effect of granulation conditions on other properties of the granulate as the material is typically accumulated on the smelter site. It is becoming recognized that slag has many potential commercial uses and carries much of the energy applied to the smelting operation. This paper outlines the findings of extensive work to identify uses for granulated non-ferrous slag, the importance of preparation conditions on the properties, impediments to more extensive use of granulated slag, the real costs of slag stockpiling and the opportunities for further productive research.

Jan 1, 2006

By M. N. Semenoff

On July 8, 1999, EPA announced the RCRA Cleanup Reforms, a set of administrative reforms designed to achieve faster, more efficient cleanups. This paper will discuss the Reforms, the status of their implementation and assess these potential impacts on the mining industry.

Jan 1, 2001

By J Aydin Bilgin, Sedat Esen

This paper describes the ideality of some commercial explosives with the help of the detonation theory and detonation velocity measurement. Ideality of an explosive can be determined by comparing experimentally measured and ideal detonation velocities. A measured detonation velocity at a certain charge diameter markedly lower than the ideal value indicates incomplete reaction and thus non-ideal detonation. Since it is shown that commercial explosives exhibit non-ideal behavior, two-dimensional detonation theory should be used to evaluate the performance of explosives. This theory enables to compute the detonation properties of explosives (detonation velocity, detonation pressure, etc.) as a function of charge diameter and confinement. The use of the one-dimensional detonation theory to compute the detonation properties for commercial explosives has an error associated with it as these calculated properties are independent of charge diameter and confinement. It assumes that shock front is planar. Hence, it is incapable of assessing the ideality of the explosives due to its assumptions. Shock front in real situation is curved in shape but not planar as in one-dimensional detonation theory. In this paper, the non-ideal behavior of some commercial explosives is modeled using EXRINT code based on the steady-state two-dimensional detonation theory firstly. Then the degree of ideality of each explosive found from the code is checked using detonation velocity test results conducted at a quarry. It has been shown that idealities of the tested explosives determined by the code agree well with the field detonation velocity test results.

Jan 1, 1999

By Chi-Mun Song, Seok-Hyun Choi, Seok-In Hong, Han-Kee Jang

Accurate measurement and evaluation of hand-transmitted vibration from a power tool is an important issue for tool manufacturers, because they are obliged to develop low-hazard power tools for workers. The International Standard ISO 5349(1) dictates a systematic procedure for the measurement and evaluation of hand-transmitted vibration. However, the uncertainty in this measurement is too large for manufacturers to apply such data to the design and modification of power tools. There can be several sources of this uncertainty in such measurements; e.g., operator-dependent, power tool-dependent, and operational conditions (see Table 1). For a manufacturer to characterize the exposure of a power tool’s use to a given level of vibration, the relationship between these uncertainty factors and the measured vibration must be elucidated. In this study, we investigated the effect of several factors on the uncertainty in measurements. [ ] Methods In this study, some of the factors in Table 1 were selected for examination, and their effect on the measured variation was quantitatively investigated. Three tools from the same manufacturer were sampled at random in our experiments, and each of five of the same type of insert (disks or tips) was installed into each tool. Although each of the tools and inserts were of the same design and were made by the same production process, they differed from one to another, which can be a source of the variation in the measured vibration. Three human subjects participated in our experiments, which were carried out as stated in ISO 5349. The subjects were asked to maintain their posture, and the applied force was kept as constant as possible. The applied force was monitored using an indirect method, where vibration energy was displayed in real time during the experiment using a three-axis accelerometer attached to the work piece at a specified point. The appropriate range of the applied force was predetermined to cover the range of real work operations. The engineering tolerance between the inner diameter of a grit disk and the outer diameter of the tool shaft leads to an eccentricity of the mass at the center of the disk. The degree of eccentricity varies with installation, and this is another source of uncertainty. In our study, the effect of this eccentricity was investigated by carrying out repeated assembly and disassembly of an insert.

Jan 6, 2006

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature of ash, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions~ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1956

By Susana Bolhão Muiños, José Hipólito Monteiro, Martin Frank, James R. Hein, Henrique Garcia Pereira, Fátima Abrantes, Tracey Conrad, Luís Gaspar

In spite of all the work that has already been done on ferromanganese deposits, studies on the Atlantic Ocean occurrences are still in their infancy and there is a clear need for investigations concerning the origin, distribution, and resource potential assessment of these deposits. Nevertheless, studies already carried out on northeast Atlantic seamounts indicate the general presence of ferromanganese deposits of hydrogenetic origin, i.e. deposits formed by direct precipitation of colloidal, hydrated metal oxides that are scavenged from the water column on hard-rock substrates. The hydrogenetic precipitation promotes the enrichment of ferromanganese crusts in many trace metals, most of which are of economic interest, such as Co, Ni, Te, rare earth elements, and platinum-group elements and thus ferromanganese crusts are considered an important metal resource.

Sep 1, 2014

Laboratory scale flotation tests were done on mineral hematite and aspecular hematite ore using oleic acid and sodium oleate as collectors. The mineral hematite floated strongly in the neutral pH region, with an increased pH range of flotation at higher oleate additions. Concentrates with sufficient hematite grade to meet the paint pigment specification were produced using oleic acid and sodium oleate as hematite collectors on the specular hematite ore. Hematite recoveries of 70 per cent at 60 per cent Fe grade were obtained using stagewise roughing. The interaction between hematite and oleate was confirmed as chemisorption but the exact mechanism could not be determined, as two independent phenomena can be used to explain the fact that the pH of maximum grade increased with increasing oleate addition.

Jan 1, 1999

By G. Delagrammatikas, M. Karmis, J. Mastoris

The evaluation of raw materials in terms of quality profile, mineralogical character and mechanical properties is of great importance to the cement industry. The variability of their chemistry and structure is among the decisive design parameters in the choice of any mining, handling and preblending systems. Furthermore, clinker and cement production require sound estimates of the above parameters, to help produce some appropriate and realistic raw mix configurations and achieve minimum standard deviation of the major components. This paper addresses this subject from the perspective of a cement producer and presents the principles of a methodology aimed at optimizing mine planning and process design. Finally, results from case studies on actual sedimentary deposits currently in operation are discussed.

Jan 1, 2002