Search Documents

By S. Garcia, J. Gebhardt, D. McBride, A. Hernandez, A. Esplín, M. Cross

The Minera Yanacocha operation consists of several heaps interconnected with ponds and gold recovery plants and presents various operating challenges. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters and inventory issues. An integral component of the process water/mass balance is a model of each heap that describes heap behavior based on the individual characteristics of the heap. The heap models are linked to a mass balancing program in order to track flows and concentrations throughout the circuit. A case study of the process heap model is presented for the La Quinua heap, including results for the normal base line operation and several operational problems such as loss of solution flow to the heap (i.e., pump failure), increased flow to a section of the heap (i.e., pond volume control), effect of significant rain events, and impact of a change in material properties (i.e., change in ore type). The impact on heap operating efficiency is discussed with regard to effects on recovery and gold solution grades.

Jan 1, 2007

By Thomas T. Read

I. INTRODUCTION. WHEN so much has been written upon a subject on which so little definite information is available as upon this, some reason must needs be assigned for adding to the volume of literature. A sufficient reason is found in the probable great future importance of China as a producer of mineral wealth. The present undeveloped state of mining in the Empire is due to many causes, among which the most important are the relatively simple needs of the population, the lack of transportation-facilities, the inelastic regulations governing the industry, and the superstitious reluctance of the people to make excavations which might disturb the spirits of the earth and air, or of ancestors. Iron is the metal most in demand, yet the needs of the population, until recently, only made necessary a production of approximately 0.5 lb. of iron per capita per year. The present annual production of iron for domestic consumption, in the United States, is nearly 600 lb. per capita. The curious state of development of transportation in this interesting country has been a greater handicap upon the mining industry than upon any other. The point upon which it hinges is the absence of a road-system. Except for a few military roads, now almost impassable, there are no roads in China; that is to say, there is no land which is set aside as a right of way, belonging to the commonwealth. Throughout the agricultural districts, generally speaking, the entire area is in private ownership, and the lines of travel are between fields. There is a constant struggle for existence between the owners of the land and the traveling public, with the natural result that the so-called roads usually

Mar 1, 1912

By O. C. Garst

"The lightness and relatively high strength per unit weight of certain magnesium alloys have interested designing engineers for many years. Ever since the noted investigator Bunsen3/ first produced the element by electrolysis of the fused chloride in 1852, utilization of this light metal has been considered. Magnesium is widely distributed over the earth's surface in high-grade as well as low-grade deposits; it occupies eighth place in the list of elements arranged in order of their decreasing abundance, as there is 2.24 percent magnesium in the earth's lithosphere. Even though the element is distributed widely in the form of relatively insoluble: minerals and also as soluble salts in sea water and spring water, as well as being an indispensable constituent of plants and animals, the technology of magnesium was slow development. This slowness of development was first caused by confusion or the part of the early investigators who thought that magnesia, magnesite, magnetite, and the pyrolusite-type manganese ores were compounds of the same metal. At one time the metal that we now know as manganese was called magnesium, and magnesium was called either magnium or talcium. In addition to this coon, the chemical activity of the metal, especially at high temperatures, created problems that are still difficult to solve.With the advance of science in all branches, .methods for -he production of magnesium were developed. The methods first used for producing the element were: (1) reduction of magnesium salts with alkali metals,4/ (2) electrolysis of aqueous solutions of magnesium salts, and (3) electrolysis of fused magnesiun salts.The first attempts to produce magnesium by the carbothermal reduction of magnesia were failures as sufficient thermodynamic knowledge concerning the reversibility of the reaction between magnesia and carbon was not at hand. As the igneous electrolytic Method for making the element was more easily controlled than the others and. yielded more metal per unit of energy, considerable work was expended on the improvement of this process. The work in this field paralled that on the electroreduction of aluminum and the alkali metals. For several years the entire magnesium industry was dependent on this igneous electrolysis process for its supply of the metal, but as demand for the metal increased and more scientific knowledge was available, other processes were developed. Today magnesium is produced by the electrolysis of molton magnesium chloride electrolytes, the carbothermal reduction of magnesia, in arc furnaces followed by shock cooling of the furnace gases by a coin inert atmosphere, and the silicothermal reduction of calcined dolomite in stainless steel retorts."

Mar 1, 1946

By H. Kenworthy

Sulfide-ore concentrates containing cobalt, nickel, copper, lead, and iron from the operations of the National Lead Co. at. Fredericktown, Mo., were treated successfully on a laboratory scale to recover more than 90 percent of the cobalt, nickel, and copper. A cobalt -nickel-bearing, lead-copper matte., produced by the St. Joseph Lead Co. at Herculaneum, Mo., was treated to produce a lead-zinc fume, a copper sulfide concentrate, and a cobalt nickel-iron product, netting a recovery of over 75 percent of the cobalt and about 90 percent of the nickel and copper. National Lead Co. bulk concentrates were chlorinated with gaseous chlorine to form anhydrous metal chlorides and sulfur chlorides, sulfur chlorides were recovered by distillation, a high percentage of the ferric chloride was converted to ferric oxide, and the chlorinated residual metals were extracted with water. Metal ions were removed from leach liquors by pH-controlled fractional precipitation as hydroxides. Cobalt solutions "were prepared from cobaltic hydroxide, and procedures were developed to remove contaminating metal ions. Purified cobalt solutions were employed as electrolytes for deposition of high-purity cobalt.

Jan 1, 1953

By John A. Davis, David W. Brunton

During the past few years great progress has been made in the United States toward safer, more efficient, and more economical tunneling methods. This advance is partly due, no doubt, to the recent increase in the number of tunnels and adits driven for devel- oping and draining mines and transporting ore. The Bureau of Mines during 1911 and 1912 made a special examination of this phase of mining operations, in connection with an investigation of mining methods and means for preventing accidents. The details especially studied were the provisions for the safety of employees, the kinds of equipment, the methods of driving, and the costs of con- struction. The results and conclusions obtained from that investi- gation are discussed and summarized in this bulletin. Up-to-date information concerning tunneling methods is difficult to obtain. There are few books on the subject; and much of the material they contain, although interesting and of value historically, is now obsolete. The engineering periodicals, it is true, endeavor to keep abreast of the times, and several in nearly every issue present some article bearing upon tunnel work. But the very multiplicity of these articles prevents one from reading them all, and the foreman or superintendent in charge of a tunnel, or the mining engineer designing one, and especially the business man financing the project, has no time for a lengthy search after scattered articles in order to determine the present status of tunnel work. Then, too, knowledge of new methods travels slowly. Valuable inventions and improve- ments in tunneling as well as in all the other industries frequently remain in the notebook of the investigator, or as theses are buried in university libraries, or are published only in journals of small scien- tific societies. New tunneling methods and equipment that are prov- ing safe, efficient, and economical may be totally unknown outside the district in which they originate. This paper, based on a special examination both in the field and in engineering literature, is in- tended to supply data concerning modern and recent tunneling practice in the United States, and to make suggestions that, it is hoped, will result in a saving to the mining industry of energy, capital, and life.

Jan 1, 1916

By S. Burks

This paper develops the themes explored by the authors at the Fourth International Platinum Conference,. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: > An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated > An existing operation with an integrated portfolio of mines, concentrators, smelter, and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets > An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated > An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the owner's team.

Jan 1, 2013

By Michael P. Amsden

"THE ECSTALL CONCENTRATOR is situated adjacent to Highway 101 and the Ontario Northland Railroad, 15 miles east of Timmins, Ontario. Ore is delivered to the concentrator by rail from the mine, which is 17 miles northwest of the plant. Power and fuel are obtained from the hydro and natural gas lines which pass close to the plant site. Water is obtained from the Frederickhouse River, 6 miles east of the concentrator. The main concentrator building is a large structure 500 by 640 feet by 90 feet high and contains facilities for fine crushing, crushed ore storage, grinding, flotation, tin recovery, concentrate handling and reagent handling. Located in the same building are the machine shop, warehouse, metallurgical laboratory, pilot plant, men's change room, sample preparation area and an assay laboratory. The general concentrator layout is shown in Figure 47. Originally designed to handle 9,000 tons per day, the concentrator now treats 10,000 tons per day. Two different ore types are processed by selective flotation in three individual circuits to recover copper, lead and zinc concentrates. In 1973, another circuit was added to recover pyrite and tin concentrates from the combined zinc tailings of the three main circuits."

Jan 1, 1974

By P. K. Chatterjee, G. D. Just

Sublevel open stoping is a low-cost method that has been successfully employed in many large underground mining operations. Where ore body characteristics are suitable, extensive mechanization and the use of large-scale stoping techniques can considerably reduce operating costs. However, careful long-term planning of mine layouts and large capital commitments in development are required prior to production. Implementing precise mine design procedures and carefully controlling operations can result in considerable benefits. This article describes methods to achieve these objectives based largely on mining operations at Mount Isa, where sublevel open stoping has been used since 1932. Ore won by this method accounted for a very large percentage of the total tonnage produced at Mount Isa. Major costs associated with sublevel open stoping can be classified as drilling, explosives and charging, and LHD costs. In this article, analyses of these costs are made with particular reference to stope design. Parameters such as burden, drill hole diameter, explosive density, specific charge, etc., are considered in establishing the interrelationship of unit operating costs, as well as total costs of sublevel open stoping.

Jan 10, 1981

By E. C. Yeager, E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. G. Gernes, W. L. Patty

"In July 1943, the Bureau of Nines received an appropriation to investigate the beneficiation of Minnesota iron ores through the use of lignite. The broad objective was to find a way to link the large deposits of lignite in North Dakota with the low-grade iron ores of Minnesota. It was proposed that sponge iron might be made through new methods of processing, and one of the objectives was to determine the possibilities of gaseous reduction of fine ore. The problem of obtaining high-hydrogen reducing gases from lignite was assigned to the Subbituminous Coal and Lignite Section of the Bureau of Mines in August 1943.Through the advice of technical consultants and men familiar with the mineral resources of Minnesota and North Dakota, a tentative program of development was outlined. The first proposal was to study the gasification of lignite briquets in a standard water-gas machine. Previous experience with gasification of lignite indicated that the raw fuel would not be suitable for use in the conventional water-gas process on account of degradation, but gasification of lignite briquets appeared possible. Through the cooperation of the Northern State Power Co„ a series of tests was made at the company's plant in Grand Forks, N. Dak., on lignite-char briquets made by the Lehigh Briquetting Co. at Dickinson, Dak. These briquets are made by the Lurgi process, and they have been used satisfactorily as a domestic fuel. The object of the tests was to compare gasification properties of lignite-char briquets with those of gas. coke made from Kentucky coal, normally used in the Grand Forks plant. The tests revealed that the lignite-char briquets were not suitable for gasification, in the standard water-gas process because of disinte-gration and low efficiency caused by loss of fine carbon.While these investigations were underway, a joint Minnesota-North Dakota Development Commission was formed to aid in planning investigations on development of mineral resources of the two States. Some members of this commission were technical men, who with consulting engineers on the Bureau's staff made up an unofficial technical committee, and assisted in solving certain problems connected with gasification of lignite and beneficiation of iron ores. This committee has been of 'real assistance in guiding the investigation.A technical meeting was held in Minneapolis on November 10 and 11, 1943, for further discussion of objectives and certain technical problems. Results of tests on lignite briquets were presented, and several reports analyzing other methods of gasification were discussed. The Reyerson-Gernes process for the continuous gasification of lignite in an externally heated retort was considered from several angles. This process differs from others in that the natural moisture in the coal is utilized to help gasify the coal, and the volatile matter is largely decomposed. Although this process had been carried out successfully in a small steel retort, no definite design for a commercial-scale retort had .been developed. It was first proposed that the process might be carried out in a Glover-West retort. However, it was brought out that a Glover-West retort would require modification to simulate the process correctly, and that good results might not be obtained even then owing to the leakage of gas through the refractory walls and to an anticipated low rate of heat transfer at the gasification temperature suitable for lignite. Further, the probable leakage of inert furnace gas into the water-gas would be adverse to the Objective to obtain a gas that could be purified to 96 percent hydrogen."

Jun 1, 1946

By Silvio Hernández Aquije

El presente texto señala el descubrimento del yacimiento vanadífero de Minasragra a través del reporte de Yeatman-Berry en 1916 y el de Kett-Sproul en 1931. Así también señala los tipos de mineralización como la mineralización primaria y por impregnación.

Jul 1, 1955

By Paul M. Tyler

The literature on radium is already voluminous, but mcuh of it is too technical to be intelligible to the average reader, and there is no single publication that covers certain economic features of the radium industry. As a result of the renewed interest in the possibilities of domestic carnotite deposits a number of requests have been made to the Bureau of Mines for information, more particularly with reference to the business aspects of the industry. In order to meet this apparent need, the present paper has been prepared from material available in the files of the bureau. The technical data are compiled from various sources and are believed to be reasonably dependable, but the attempt has been not so much to achieve meticulous scientific accuracy as to brim; together facts of industrial significance and popular interest. GENERAL DESCRIPTION Radium is a brilliant white metal that melts sharply at about 700°C. and volatilizes appreciably at that temperature. With an estimated specific gravity of nearly 6.0, it is more than twice as heavy as aluminum and 25 per cent lighter than irons. Although it has been isolated in its metallic state, it is not used in that form, partly because it tarnishes rapidly even in dry air (forming a nitride), partly because of the greater expense of reducing it to metal, and partly because of the difficulty of dealing with such minute quantities of material. It is used always in the form of its compounds, the most important of which from the vie point of utilization are the bromide, chloride, and sulphate.

Jan 1, 1930

By Joel A. Hunt

The Bunker Hill Mine, located in north Idaho, consists of over 150 miles of passageways within highly fractured and faulted Precambrian metamorphosed rocks. The Bunker Hill Mine was at one time a major producer of lead and zinc; currently it is on inactive but maintained status. Ground water moving along flow paths that have been disturbed by mining reacts with pyrite and oxygen to produce acid water within the mine. Discharge of this acid water averages more than 5 cubic feet per second, with an average zinc concentration of 160 mg/L and pH of 2.8. Treatment of this acid mine drainage is required by the National Pollutant Discharge Elimination System (NPDES). Cessation of all underground activities at the Bunker Hill Mine will not terminate the production of acid mine drainage. Reclamation alternatives that could either reduce the quantity or Improve the quality of the drainage upon mine closure are highly attractive. This project is directed towards delineation of reclamation alternatives based upon an understanding of the characteristics of ground water recharge near the mine. A variety of field techniques were used to identify areas of rapid infiltration and to investigate the ground water flow system associated with the upper portion of the mine in a portion of the Milo Creek drainage. These techniques include Installation of piezometer nests, dye tracing, surface resistivity, dye dilution, spring surveys, and hydrochemical analyses. Sites of direct Infiltration into the mine have been located. These include mine workings directly below perennial streams, intersections between streams and faults, and a caved area adjacent to an ephemeral stream. Results of these investigations indicate that recharge through these sites is not as rapid as suggested by previous studies. Inflow to the underground workings from the ground water flow system around the margin of the mine may account for more mine water than sites of direct infiltration. Recharge control at areas of direct infiltration could result in a net decrease in the quantity of acid drainage from the Bunker Hill Mine. Locations suggested for recharge control are West Milo Creek above the Guy Caving Area, the intersections of the Cate Fault with South Milo and Milo Creeks, and an area of Milo Creek below the Milo Creek Dam that overlies shallow mine workings.

Jan 1, 1984

A new mine has begun production of antimony ore and concentrates in Serbia, Yugoslavia. The mine is operated by the mining and metallurgical enterprise "Aajaca." Initial production is running at approximately 45 thousand tons of ore per year, yielding about 1,500 tons of concentrate. The mine is located on the mountain Kopaonik-Raiceyoj Gori. It is planned to expand production eventually to approach the level of 300,000 tons of ore per year. This level will be a significant addition to the world supply of antimony and will place Yugoslavia among the world's major producers. Currently the United States produces only about 6 percent of its primary requirement for antimony. COBALT -Anglo American Corporation, Ltd. reportedly is considering restarting the Tenke-Fungurume copper-cobalt project in Zaire. Construction on the project was suspended in January because of inadequate financing and political uncertainties. Technical feasibility and financing on a smaller scale than previously envisioned are now being considered. However, an increased copper price may be necessary before any decision to proceed is made.

Jan 1, 1976

By J. E. Dutrizac, J. B. O'Reilly

"Zinc is a relatively abundant element which occurs as both high-grade sulphide ores {sphalerite ZnS) and oxide ores which the ancients collectively termed ""calamine"" (smithsonite ZnC03 and/ or hemimorphite Zn4Si201(0H)2 - H20 and/ or hydrozincite Zn5(C03) 2(0H)6). Although oxidic zinc is readily reduced by carbon, the process becomes thermodynamically viable only at - 1000°C, and at this temperature the zinc is released as a vapour (B.P. 907°C). Casual cooling of the vapour results in its re-oxidation by excess combustion air or even the carbon monoxide product of the reduction reaction. ZnO + C = C09,, + Zn vapom Only fairly rapid quenching of the zinc vapour and the isolation of the reduction products from the combustion gases will yield metallic zinc; these conditions were not produced deliberately until the advent of distillation technology. Until quite recently, the principal use of zinc was in brass manufacture; galvanized iron was not discovered until the 19th century and zinc casting alloys are a relatively recent invention. As will be seen, brass could be produced without recourse to a pure zinc intermediary, and the discovery of brass preceded that of zinc by many centuries. The purpose of this paper is to outline the discovery and early development of both zinc and brass with special reference to the European scene."

Jan 1, 1999

By O. Bazhko, F. D. L. Uahengo, Y. R. S. Hara

Although the conventional acid-reductive leaching method effectively extracts copper (Cu) and cobalt (Co) from Cu–Co oxide ores, efforts to enhance hydrometallurgical performance are ongoing. This study evaluates the influence of sulphuric acid (H2SO4) and sodium metabisulphite (Na2S2O5) on metal extraction from Zebesha Cu–Co oxide ore using ferrous sulphate heptahydrate (FeSO4·7H2O) and ferric sulphate (Fe2(SO4)3) as lixiviants. Ore samples (<150 μm) were leached at ambient temperature for two hours, and metal concentrations were determined via X-ray fluorescence analysis. In the FeSO4·7H2O system, Co, Mn, and Ni recoveries increased w=ith Na2S2O5 concentration, reaching a maximum of approximately 80% Co at 150 kg/t, while Cu recovery remained below 5%. Conversely, with Fe2(SO4)3, Cu recovery peaked at 88% at 50 kg/t Na2S2O5, then declined to 79% at 150 kg/t. The addition of H2SO4 improved metal recoveries in both systems. Notably, 60 kg/t H2SO4 yielded 92% Cu extraction in Fe2(SO4)3, while Co, Ni, and Mn remained below 40%. However, in FeSO4·7H2O, Co recovery improved from 40% to 84%. These findings suggest Na2S2O5 is more effective for cobalt extraction with FeSO4·7H2O, whereas H2SO4 enhances copper extraction in Fe2(SO4)3.

Oct 24, 2025

By Shigeru Tsutsumi

The rapid development of transportation facilities in Japan focused the attention of this country on the possibility of converting the existing coal resources (of which there was an abundance) into liquid fuels, for which there was a constantly increasing demand. Previous work had indicated that this could be accomplished by utilizing one of two processes - the Bergius process, in which high temperatures and high pressures were employed to effect direct liquefaction of the coal, and the Fischer-Tropsch process, in which an indirect liquefaction of coal was accomplished by the production of liquid hydro-carbons from hydrogen-carbon monoxide mixtures. This report describes some investigations into the latter process, which was first developed by Fischer and his colleagues in the Coal Laboratory in Muhlheim, Germany, in 1923. By 1932, these investigators had achieved a 60-percent theoretical yield (152 ml. of liquid hydrocarbons per cubic meter of 2H2:ICO synthesis gas) by using a precipitated Co-Th02 catalyst.3/ At the same time (1932), Dr. Kita of Kyoto Imperial University and Messrs. Fujimura and Tsuneoka obtained 145 ml. of gasoline (C5+) per cubic meter of synthetic gas by using a Co-Cu-Th-U catalyst. 4/ This report is a description of the experimental results subsequently obtained at the Fuel Research Institute, Kawaguchi City, Saitama, up to 1935.

Jan 1, 1951

By Robert C. Stanley

The prominence of her mineral resources makes Canada a most fitting place in which to hold the Second Empire Mining and Metallurgical Congress, since in all probability the Dominion has more diversified mineral wealth than any other part of the British Empire. This paper is concerned with nickel, an important factor of Canada&apos;s mineral production. The richness and quantity of her nickel ores have made Canada the world&apos;s most important source of supply of the metal. Its history and diversified uses are, therefore, particularly interesting at this meeting. Early History Probably the first use of nickel by man was in the fashioning of implements, and later swords, from nickel-bearing meteorites, masses of metal that have fallen from time to time at many points on the earth&apos;s surface and which consist normally of iron carrying substantial amounts of nickel. Meteorites were perhaps the first metal known to man. The falling star, sought out with fear overborne by curiosity, was found to be a better stone than the earth-given, truly a boon from the gods. Archaeologists tell us there is good evidence that the ancient oriental peoples learned at an early date to make these stones into useful implements. The invincible blades of the great warriors of old, in China, Persia, and in northern Europe, were Heaven-sent, a fable which sounds significant of meteoric iron. Probably some of the ancient swords of Khorassan and of Damascus were of meteoric nickel-bearing iron.

Jan 1, 1927

By J. Venter

The history of firedamp is the same as that of coal: The initial stage was the accumulation of vegetation, which was converted into peat under certain local conditions, then lignite, bituminous coal, and finally anthracite. These deposits ceased to increase owing to inundation that deposited earthy sediment, sometimes as much as several tens of meters (several tens of yards). The vegetable matter, whether it was covered with sediment or not, began to ferment. The basic organic components of the vegetable matter are: Cellulose, lignin, and wax and resin in varying proportions, according to the different kinds of vegetable matter. There are, in addition, some impurities, generally mineral.

Jan 1, 1953

By R. E. Scheffel

Most supergene copper heap leach operations today employ forced-aeration, irrespective of ore grade. Unfortunately, there is little published quantification of its benefit. There is a natural desire to strive for the ideal chemical kinetics. The reality, however, is that physical mechanisms control the commercial extraction rate. This paper presents the performance of a number of operations, their operating conditions and physical ore characteristics, which contribute to non-ideal solution distribution and variable extraction rate. Regardless whether one uses forced-aeration, commercial experience to date suggests it is prudent to design for longer leach cycle times to ensure the production target is met.

Jan 1, 2006

At the end of August, U.S. producer posting of 99.5 percent unalloyed aluminum had been established at 48¢ per pound. At that time, dealer-quoted unalloyed ingot was reportedly at 44¢-47¢. CADMIUM: By late August, most U.S. producers had raised cadmium selling prices by 25¢ to $3 per pound. As a consequence, dealer quoting of cadmium ranged from $2.95 to $3.05 per pound. COAL: The wildcat strike, which began in southern West Virginia on July 19 and eventually spread to nine other States before ending on August 13, at its peak, idled approximately 115,000 miners and accounted for daily coal losses of an estimated 1.5 million tons at the height of the work stoppage. Concerned about the effects of the production cutbacks, the Bureau of Mines, early in the strike period, initiated its coal strike monitoring system which it had developed during the prolonged coal strike in the fall of 1974.

Jan 1, 1976