Search Documents

By Daniela Venter, Stephen Chryssoulis, Ken Stowe

"A sampling campaign was conducted at Kemess in order to identify and assess the chemical and physical factors, which control free gold flotation kinetics in the rougher and cleaner circuits. The rationale behind this approach was that accurate knowledge of the parameters affecting free gold flotation kinetics, can be used to determine how to accelerate free gold flotation. Collected samples were composites of 5-6 cuts over a four-hour period, at steady plant conditions.In the rougher circuit, coarser equidimensional gold particles floated ahead of the finer grained and the flaky gold. Sulphur followed by molybdenum and to a lesser extent silver enhanced gold flotation kinetics, while hydroxyl followed by carbonate ions induced depression."

Jan 1, 2003

By Karl J. C. Harries

"11.1. INTRODUCTIONA royalty is the most common form of interest retained by an owner who is disposing of his property or by a joint venturer who ceases, voluntarily or otherwise, to participate in the joint venture.1 Rarely does a non-participating party have a direct interest in the property and/or assets of a project, except during the period when a non-participating joint venturer may be having his interest diluted.2 In fact, it is most unwise to permit a non-participating party to have such an interest. It may give rise to significant problems that could prevent or substantially delay the development of an orebody and require a considerable amount of time, effort, and money to correct.3In negotiating a royalty, it is important to be aware that there is no law or convention that says, “You just don’t do that in a royalty agreement.” As with any agreement, inventiveness and flexibility on the part of the negotiator are not just assets, but virtual necessities. It is also for this reason that it is essential to read the royalty provisions, particularly the definitions, fully and carefully, especially if you are the recipient. On the other hand, if your inventiveness and flexibility cause your accountant to question the advisability of one of your ideas, pay close attention to him.4 He will, no doubt, have had experience with many royalties, and no competent professional adviser disparages a client’s ideas without good reason. Besides, he will probably be the person who will be determining the royalty or certifying the determination of it. At the very least, he will be auditing your general financial statements, which must, of course, reflect the royalty determination. Heeding his advice not only may make the determination easier but also will probably save you money in professional fees later on. Nevertheless, do not simply accept his comments or recommendations without understanding what they mean, why they have been made with respect to your royalty agreement (sometimes professionals have comments that they make as a matter of course and, even though they may be valid, you should require them to be justified to you), and how they will affect your royalty determination.It is surprising how many corporate payors insist that their standard royalty provisions5 be used as a matter of policy, thereby effectively tying the negotiator’s hands. It is even more surprising, and to professional advisers frightening, how many of the senior employees who insist that such a policy be adhered to, virtually without variation, do not know what is in the standard provisions and would be hard-pressed to explain them to a property owner. If standard provisions are appropriate, by all means use them, but do allow experienced and sensible negotiators some flexibility and make sure that everyone within the corporation who may have to use such provisions – negotiator and supervisor alike – knows what they contain and why they are as they are. For example, there are often good and convincing reasons to describe a deduction in a certain way or to include a certain specific type of deduction. On the other hand, quite often the answer to the question “why?” is that “it has always been there”; this is, or should be, an unacceptable answer. In any event, if you, as the negotiator, appear to know what you are talking about, are familiar and comfortable with your royalty provisions, and are backed up by your boss with the same words or reasoning, a property owner cannot help but be satisfied that you are knowledgeable, even if he still does not agree with your provisions. Finally, if you do use standard provisions, make sure that they are reviewed and updated regularly."

Jan 1, 2003

By Yoshihiko Maeda

It is said that the 21st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980'h due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologis and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

By R. C. M. Minnitt, W. Dr. Assibey-Bonsu, F. A. Camisani-Calzolari

Born in Bothaville (OFS) on the 26th August 1919, Daniel G. Krige grew up in Krugersdorp on the West Rand. Hematriculated from Monument High School in Krugersdorpin 1934 at the age of 15 and graduated with a B.Sc. (Eng.)degree in mining engineering from the University of the Witwatersrand at the end of 1938 (age 19). In 1938 he joined Anglo Transvaal where he worked on a number of gold mines until 1943, gaining a wide range of valuable practical experience in surveying, sampling and ore valuation. He then joined the Government Mining Engineer’s Department where he worked for 8 years during which time he participated in the uranium negotiations with the British and American authorities and designed the uranium pricing formula for the contracts which led to the establishment of South Africa's profitable uranium industry in the early 1950s. During the same period he began his pioneering work in the application of mathematical statistics to the valuation of new gold mines using a limited number of boreholes and of ore reserves for existing mines. His early papers in the application of mathematical statistics, some republished in French, created world-wide interest that led to the development of the science and concepts that surround the spatial evaluation of mineral resources and reserves known as geostatistics. This technique has contributed to improved ore evaluation techniques as well as the reduction of the financial risks associated with investment in mining enterprises. Furthermore, it led to the recognition of his contributions to the evaluations of mineral deposits through the coining of the term ‘kriging’ that is used to describe a spatial mineral evaluation process known and practised in international mining circles. He continued his work in geostatistics throughout his career as Group Financial Engineer of the Anglovaal Group until his retirement in1981 and afterwards for ten years as Professor of Mineral Economics at the Witwatersrand University. He is still active as a consultant and is a registered Professional Engineer. He has published some 90 technical papers both locally and overseas, some in Russia, and has lectured and participated in international congresses in many countries. His contributions were recognized by the Witwatersrand University through the award of the D.Sc. (Eng.) degree in1963, by three honorary degrees (from the universities of Pretoria, UNISA and Moscow State Mining University), by many awards from the South African Institute of Mining and Metallurgy, the International Association for Mathematical Geology, Die Suid Afrikaanse Akademie vir Wetenskap en Kuns, the SME of the American Institute of Mining Engineers, the International APCOM Council in1999, the University of Antofagasta in Chile, and by the South African President (Order for Meritorious Service, Class 1, Gold). He has served on various Government committees, notably that for State Aid for gold mines (1967/8) and designed the State Aid formula which enabled many mines to survive a period of low gold prices; also various taxation committees, and the mining mission to Iran in 1974. He is a fellow and/or honorary life member of various technical societies locally and overseas, including the Royal Society of South Africa. During the period in the Government service he also handled several of the post-war lease applications in the Free State and Klerksdorp goldfields. The fact that decisions on new gold mines of critical importance to the State and the economy as a whole, were being taken on a limited number of drillholes without any scientific analysis of the risks of failure, stimulated him to start basic research into ore evaluation. His approach was based on the application of Mathematical Statistics to these problems, an approach of which very little was known world-wide at that stage but which had already been initiated in South Africa by Sichel via the lognormal frequency distribution model. In Krige's 1951 paper published in the Journal of the Chemical, Metallurgical and Mining Society of South Africa he covered the statistical explanation of the conditional biases in ore block valuations and stimulated the use by several gold mines of regression corrections for routine ore reserve valuations, a technique which, in effect, was the first use on an elementary basis of what is now known as kriging. His 1952 paper introduced, inter alia the basic geostatistical concepts of ‘support’, ‘spatial structure’,’ selective mining units’ and ‘grade-tonnage curves’. His 1951 paper was based on his M.Sc. (Eng.) thesis submitted in the Department of Mining Engineering to the University of the Witwatersrand, and expounded his pioneering work in geostatistics in more detail. His early research papers that had stimulated interest in several mining circles overseas, were republished in French in1955, resulting in a major research effort by French mining engineers in this field. This, in turn, led to the establishment of the now world-renowned French school of ore evaluation in Fontainebleau, Le Centre de Geostatistique de l’École des Mines de Paris. As the Group’s Financial Engineer at the Anglovaal Head Office until his retirement in 1981, he was responsible for

Jan 1, 2003

By Todd S. Fayram

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering program that culminated in this successful process.

Jan 1, 2003

By John Ralston, Jonas Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By T Laurencont

The Queensland Department of Natural Resources and Mines (NR&M) accepted the environmental liability for the Mount Morgan minesite in 1991. This gold and copper mine located 38 km southwest of Rockhampton had been in operation for more than 100 years. Mining leases are still active while the feasibility of a reprocessing operation is carried out. From 1993, NR&M have operated a seepage interception pumpback system which has reduced the chronic load of acid rock drainage (ARD) to the adjacent Dee River, a tributary of the Fitzroy River system. In early-2000, it was recognised that a ten-year plan for rehabilitation of the mine, along with significant funding would be required if a long-term sustainable rehabilitation strategy was to be implemented at this minesite, ultimately making the seepage interception system redundant. A rehabilitation planning workshop coordinated by NR&M was held in May 2000. This workshop brought to the mine a range of technical expertise and key stakeholder groups. This workshop provided a technical forum for review of studies undertaken and to identify priority projects, which needed to be undertaken in the future to more clearly define contaminant sources on the mine site and to prioritise the rehabilitation program. Stakeholder consultation enabled the project team to be clear on community and other government (eg Environmental Protection Agency) expectations. It is clear that the future of the economically depressed community of Mount Morgan will be reliant on the careful management of the significant heritage values at the minesite for tourism, education and research. In the first year (2000), priority studies were initiated, which included whole of site studies on water balance, contaminant sources and a review of occupational health and safety and environment of the minesite and conservation and heritage scoping. Baseline vegetation and soil materials surveys were also initiated. The outcomes of these studies helped to shape the work program for the following year, while providing a basis for an additional funding application, which was granted. The second year of studies focused on building upon the existing baseline studies completed. In addition, studies focussed on addressing the priority issue of contingency planning for overflow from the open cut pit in accordance with best practice management of release water and river monitoring strategies were completed. Completion of these projects over the next six months will enable the optimal rehabilitation strategy to be defined in 2003. This optimal strategy may require the use of a water treatment plant for part of the ten-year program to provide space in the open cut pit for the deposition of ARD contaminant sources (eg waste dumps, tailings). It is envisaged that some sources will be rehabilitated insitu while others will be relocated to the open cut pit. Implementation of this strategy will be dependent on subsequent funding.

Jan 1, 2003

By K. Aoki, Y. Mito, S. Shirasagi

The authors developed the TBM Excavation Control System (the TBM Navigator), in order to realize the advanced observational construction. During the excavation using this system, the rock strength value is immediately calculated from the TBM driving data as an index of rock properties, and the drill energy coefficient is also calculated from the drill logging data that is carried out using the probe hole ahead of the tunnel face. In this study, a new, geostatistical simulation-based method is proposed for the automatic prediction of the rock properties ahead of the tunnel face with good precision, using both the drill logging data and the TBM driving data. The applicability of this method is validated through the prediction at the actual tunnel excavation that passes through the faults. Les auteurs ont mis au point un Système de Contrôle de forage avec la machine à pleine section (Navigateur de la machine à pleine section), en vue de réaliser un système de surveillance plus efficace. Avec ce système, la résistance de la roche est immédiatement calculée, au cours du forage, à partir des données de conduite de la machine, comme indice des propriétés de la roche, et le coefficient d'énergie de la foreuse est également calculé à partir des données de log de forage collectées dans un trou de sonde foré dans le front de taille. Dans cette étude, on propose une nouvelle méthode basée sur la simulation géostatistique qui permet de prévoir d’une manière automatique, des propriétés de roches se trouvant derrière le front de taille avec une précision satisfaisante, à l’aide des données de log de forage et celles de conduite de la machine à pleine section. Cette méthode s’est avérée suffisamment précise au cours du forage d’un tunnel réel qui traversait une zone de failles. Die Autoren entwickelten das TBM Ausschachtungssteuerungssystem (den TBM Navigator), um noch besser überwachte Bauarbeiten zu ermöglichen. Unter Einsatz dieses Systems wird die Gesteinsfestigkeit während der Ausschachtungsarbeiten unmittelbar aus den TBM Antriebsdaten als ein Index für die Gesteinseigenschaften berechnet. Gleichzeitig wird auch der Bohrenergiekoeffizient aus den Bohrlogdaten berechnet, die an Hand der Probebohrung am Stirnende des Tunnels erhalten wurden. In der vorliegenden Studie wurde ein neuartiges, auf geostatistischen Methoden basierendes Verfahren für die automatische und angemessen genaue Vorhersage der Gesteinseigenschaften am Stirnende des Tunnels vorgeschlagen, für das sowohl die Bohrlogdaten als auch die TBM Antriebsdaten verwendet werden. Die Anwendbarkeit dieser Methode wird durch die Vorhersage bei einer tatsächlichen, durch Verwerfungen verlaufenden Tunnelausschachtung bewiesen.

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. The future silicon feedstock is most likely not reject from the production of electronic-grade silicon. There will probably be a more direct solar-grade silicon route, excluding the electronic-grade silicon "detour". Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this. Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain.

Jan 1, 2003

By S. Maurigiannakis

In an effort to promote sustainability in the construction industry, the natural decorative stones that cover large external areas of buildings may be replaced with artificial stones. In this paper the physical and mechanical properties of artificial decorative stones are presented and are critically compared with corresponding natural stones. To test suitability for various applications, artificial stone specimens were subjected to weathering testing (freezing-thaw cycles in a climatic chamber). Mechanical characterization of these specimens was based on uniaxial compressive testing as well as non-destructive ultrasonic testing. Preliminary results show that artificial stones can replace natural stones, thus creating a sustainable development option for the construction industry.

Jan 1, 2003

The physico-chemical principles of chloride hydrometallurgy are reviewed to rationalise the complex chemistry in chloride-based processes for metal sulphides in terms of the predicted Eh-log[Cl-] relationships, measured changes in activity of H+, Mz+, Cl- and solubility of Ag(I), Cu(I), Cu(II), Pb(II), Ni(II), Au(III), Sb(III) and Bi(III). These changes reflect the nature of chemical speciation, competing effect of hydration/hydrolysis and chloro-complexation,composite effect of increasing acid and/or salt concentration and decreasing water activity. Rate data for the dissolution of PbS and ZnS in HCl containing Fe(III) or Cu(II) are compared and contrasted to highlight the effect of acid and chloride concentration, water activity, and the nature of oxidant. It is shown that LiCl, NaCl and HCl influence the kinetics of oxidative PbS leaching based on their effect on solubility of PbCl2 co-precipitated with elemental sulphur on the mineral surface. Evidence for the beneficial effect of Cu(II) in sulphide leaching is discussed.

Jan 1, 2003

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterizations of gold ores. However, this is not a simple tusk due to low gold grade, fine grain size, possible complex mineralogy, nugget effect, etc. Using the same sections of a gold-rich ore, a critical test was performed using an optical microscope (OM) and an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences, such as the detection of very fine gold grains is enhanced by EM. Key words: Digital imaging, Gold ores, Mineralogy, Electron microscopy, Optical microscopy

Jan 1, 2003

By Jr

This paper provides a comprehensive review of the requirements of a full due diligence study for a coal property acquisition in both text and table format. From the initial scoping of the assignment, the paper discusses in depth from reserve base validity and mineability; historic performance; plant and equipment; future mine plans; infrastructure; capital spending and operating costs; labour and management; future risk assessment and environmental liabilities; marketing; valuation and finally acquisition synergies. All are important areas to ensure the viability of the acquisition and to identify and minimise the project risks.

Jan 1, 2003

By J L. Merritt

Effective minesite water management requires that this issue be treated as a risk management exercise. The management process is generally far from simple and by necessity must involve a range of personnel covering a siteÆs commercial, operational and environmental interests and responsibilities. The challenge to be collectively faced by these stakeholders is to strike the correct balance between risk and cost. On the other hand, the challenge to be faced by technical services support personnel is to provide stakeholders with information in a format that they can use with confidence. This paper presents the application of continuous operational simulation (OPSIM) modelling techniques to establish appropriate risk profiles for minesite operations. It is necessary that the format of these risk profiles be generic and equally applicable for defining the risk of occurrence for a relatively comprehensive range of activities û eg from of a non-compliant discharge, to the risk of failure to meet production targets. What is more, the profiles need to be quantitatively based and capable of reflecting change in system response to varied operational or management strategies. The techniques presented in this paper are based around a key assumption that long-term records of the climate contain within them sets of sequences that are representative of what can be expected in the future û that is, the droughts, floods, cyclones, good years and bad, long or short, and everything in between. Therefore, if these historical records are run through an OPSIM model for a particular site, then the simulated operational characteristics can be taken as being representative of what can be expected in the future, in the long-term. This lends itself to statistical analysis and translation into the required risk based format. Water Solutions Pty Ltd have been working with Capricorn Coal Management to develop a relatively comprehensive OPSIM model of their operations at German Creek Mine, Central Queensland. Outcomes from the modelling have been used in recent times to provide mine management with risk-based guidelines for both securing and containing mine water inventories. One of the more interesting tasks has been to establish risk based inventory levels that, if reached, would trigger the immediate implementation of a contract for the desalination and re-use of mine water, at predefined rates. Also, lead-time warning of the occurrence of a possible trigger is of importance to operational and commercial planning. To service this requirement the OPSIM model is regularly used to produce lead-time estimates to defined levels of confidence. Case studies of these, and other, applications of the OPSIM model at German Creek Mine are presented in this paper and serve to demonstrate an effective methodology for practical risked based water management.

Jan 1, 2003

By Anna Arkhireeva, John N. Hay

Considerable interest has been shown recently in organically modified silicates (ormosils) because of the wide range of possible applications for these interesting organic-inorganic hybrids. These applications include the use of the hybrids as modifiers of a range of host polymer proper- ties. The ormosils can be synthesised by the conventional hydrolytic sol-gel process, as well as by the non-hydrolytic sol-gel route. To date, however, there are relatively few reports of the synthesis of sub-micron size ormosil particles of well-defined spherical morphology. Here, we report work to date on synthesis of such nanoparticles and also introduce our own work in the area.

Jan 1, 2003

By G. Dhakal, J. -I. Kodama, K. Neaupane, T. Yoneda

ABSTRACT Durability tests and evaluation of sub-zero temperature effects to some argillaceous clastic rocks were carried out. Welded tuff, limestone, sandstone and schist samples collected from different parts of Japan were tested and results are presented. Schist and dolomite from Ganesh Himal area along the higher Himalayas of Nepal were also tested, and the results are compared. The slaking tests were performed on all samples in pure water. The results reveal that the slaking index of schist from Japan is lower than that of schist from Nepal. Regarding carbonate rocks, the slaking index of limestone from Japan is higher than that of dolomite from Nepal. A tendency of decrease in slake durability with an increase in porosity is also observed. Freezing and thawing experiments conducted on welded tuff and schist reveal that crack initiates earlier but extends slower in schist than in welded tuff. It is also observed from the freeze-thaw experiment that the welded tuff deteriorates and wears faster than the schist. However, sandstone remains relatively intact for a long run of freeze-thaw cycles. Zusammenfassung Beständigkeitstests sowie die Bewertung der Auswirkungen von Minusgraden auf Tonschiefer Trümmergestein wurden durchgeführt. Dabei wurden geschweißter Tuff, Kalkstein, Sandstein und Schiefer aus verschiedenen Gebieten Japans sowie Schiefer und Dolomitgestein aus dem Ganesh Himal Gebiet, dem höheren Himalaya Nepals, untersucht und die Resultate verglichen. Für alle diese Gesteine wurden Slaking-Tests in reinem Wasser vorgenommen. Die Resultate zeigen, dass das Slaking von Schiefer aus Japan höher als das von Schiefer aus Nepal war, wohingegen bei kalkhaltigem Gestein das Slaking von Kalkstein aus Japan niedriger als das von Dolomitgestein aus Nepal ausfiel. Es wurde dabei auch eine Tendenz zur Löschbeständigkeitsverringerung bei gleichzeitig erhöhter Porosität beobachtet. Gefrier- und Tautests an geschweißtem Tuff und japanischem Schiefer zeigten, dass Risse in Schiefer schneller auftraten, aber sich langsamer ausweiteten als in geschweißtem Tuff. Bei Gefrier- und Tautests wurde ebenfalls beobachtet, dass geschweißter Tuff schneller verfällt und verschleißt als Schiefer. Sandstein hingegen blieb über lange Tau- und Gefrierzyklen intakt Résumé Des tests de solidités et l’évaluation de l’effet des températures en dessous de zéro sur les rocs argileux ont été effectués. Les rocs d’origine volcanique (cendre), les rocs calcaires, sableux et les schistes de différentes régions du Japon, ont été étudiés. Les schistes et les dolomites de la région de Ganesh Himal le long du haut Himalaya (Népal) ont été étudiés et comparés à ceux du Japon. Les tests de désintégration sur les rocs ont été effectués dans l’eau pure. Les résultats montrent que l’index de désintégration des schistes du Japon est inférieur aux schistes du Népal. En ce qui concerne les rocs carbonyles, l’index de désintégration des rocs calcaires du Japon est supérieur à ceux des dolomites du Népal. Une décroissance de la résistance à la durabilité est observée avec une plus grande porosité des rocs. Les tests de congélation-décongelation sur les schistes et les rocs d’origine volcanique (cendre) du Japon montrent une apparition précoce des fissures mais l’expansion des fissures est plus rapide dans les rocs volcaniques. Des tests similaires montrent que les rocs volcaniques (cendre) se désagrégent plus rapidement que les schistes. Cependant, les rocs sableux restent intacts après plusieurs cycles de congélation-décongélation.

Jan 1, 2003

The torsion test is considered as the best test used when the part is subjected to static or dynamic torque. Many published papers have investigated the torsion of non-heat treated metals. However, very few published papers dealt with the torsion behaviour of heat treated metals. The aim of this work was to study the effect of heat treatment on the torsion behaviour of steel alloy (AISI 01), which can be used for manufacturing small and medium drills, taps and reamers. The diameter of specimens used was 15 mm. The metal used was heat treated under different conditions, then torsionally tested. The results of torsion test were divided into two groups: results obtained during elastic limit from which the shear stress, shear strain and modulus of rigidity were calculated, while from the results obtained during plastic limit the plastic depth was calculated by applying derived equation when the angle of twist was more than yield value. The results obtained indicated that the value of hardness alone is not sufficient to establish heat treatment conditions. Rather, it was found that the determination of plastic depth together with hardness can help in the establishing of the optimum condition which was hardening temperature of 820¦C, hardening time 20 minutes and tempering temperature 220¦C. This condition produces hardness of 60 HRc and plastic depth of 2.5 mm.

Jan 1, 2003

By M. N. Brodie

"The ability to adjust the speed of a SAG mill offers benefits to the process and to equipment maintenance. It can be provided with some slight effect on availability ranging from somewhat enhanced to somewhat reduced, depending on the particular equipment that is used. Several techniques have been developed for monitoring the magnitude of the contained charge, and several algorithms have been used to control mill feed rate and mill speed. The various benefits and the means by which they can be realized are examined and compared. Reasons for Variable SpeedProcess RequirementsThe recovery of minerals from ore is dependent on particle size and residence time in process. Separation in a given plant is most efficient at a particular rate and a particular size (e.g., 80% minus 200 mesh). If the particle size increases, less mineral will be liberated. If the particle size is significantly reduced, the process of choice may not be able to effect separation, and power, media, and maintenance costs would be increased.If a SAG mill-ball mill combination delivers the desired throughput at the correct size for efficient separation when processing ore of the design hardness, some adjustment must be made to maintain this condition when the ore changes. The processing of ore softer than design will result in overgrinding, unless:• the throughput is increased inversely to the change in hardness which lowers recovery by overloading the separation facilities;• or the SAG mill feed rate remains constant, but the speed is reduced to feed coarser material to the ball mill for finish grinding to the desired size.There is also the effect of changing milldiameter to consider. A nominal 36 ft diameter SAG mill will have an effective diameter of 35 ft with new liners and 35 ft 6 in. with worn liners. A mill designed to operate at 0.76 p.u. (per unit) of critical speed with new liners (9.84 rpm) will be changed to 0.765 p.u. with worn liners. If 0.76 p.u. is the desired value, the mill speed should be reduced to 9.77 rpm."

Jan 1, 2003

"These standards were developed by the CIM for use with the value or worth of a Mineral Property as opposed to “evaluation” where the key objective is an economic assessment or determination of the economic merit of a propertyP1 .0 BACKGROUNDPl.1 There are at present no comprehensive standards for valuation of Mineral Properties in the Canadian mining industry. The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) specifically recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties.Pl.2 On May 5, 1999 at the Calgary Annual General Meeting, CIM Council approved the formation of a Special Committee on Valuation of Mineral Properties (CIMV al) to be co-chaired by Keith Spence (Chairman of the CIM Mineral Economics Society) and Dr. William Roscoe (Roscoe Postle Associates Inc.).Pl.3 The mandate of CIMVal is to recommend Standards and Guidelines for Valuation of Mineral Properties to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges.Pl.4 The members of CIMVal represent of a mix of professional disciplines and experience in the field of Mineral Property valuation:Keith N. Spence (Co-chair), Alliance Pacific Resources Inc., TorontoWilliam E. Roscoe (Co-chair), Roscoe Postle Associates Inc., TorontoMichael J. Bourassa (Secretary), Aird & Berlis LLP, TorontoChristopher R. Lattanzi, Micon International Limited, TorontoRoss D. Lawrence, Watts, Griffis and McOuat Limited, TorontoPaul E. Lunney, Noranda Inc., TorontoCraig A. Roberts, Pacific International Securities, VancouverDavid A. Scott, CIBC World Markets, TorontoIan S. Thompson, Derry, Michener, Booth & Wahl Consultants Ltd., VancouverWilloughby A. Trythall, retired Placer Dome executive and consultant, Vancouver"

Jan 1, 2003

"This document establishes standards and guidelines for scientific and technical disclosure by Issuers listed on the TSX Venture Exchange on their mineral properties. It incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.1. Introduction1.1 General(a) This Appendix establishes standards and guidelines for scientific and technical disclosure by Issuers on mineral properties. These standards and guidelines should be applied prudently and with common sense by those Issuers in conjmction with the applicable requirements of section 1.2.(b) This Appendix incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and -written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.(c) This Appendix is not intended to be exhaustive or all-encompassing and greater detail may be appropriate and required in certain situations. Issuers are encouraged to contact Exchange technical staff where they are not certain about the requirement for disclosure on mineral properties."

Jan 1, 2003