Search Documents

By G. Shen, W. R. Tyson

In most fracture toughness test standards, such as ASTM E 1290 and BS 7448, crack-tip opening displacement (CTOD) is measured by using three-point bend (SE(B)) or compact (C(T)) samples with deep cracks. The loading mode and crack depth in these tests sometimes are different from that of pipelines. Pipelines usually have shallow defects and experience tensile loading when the supporting ground moves. As a result, the CTOD measured by these samples is lower than that of pipeline in tension. Recent researches suggest using single-edge-notch tension (SE(T)) samples to measure fracture toughness for pipelines. In the present study, shallow and deep SE(T) samples under fixed grip loading were analyzed by using the finite element technique. An equation to relate the CTOD to the area of the load/plastic crack mouth opening displacement (CMOD) is proposed. With this equation, the CTOD of a SE(T) sample can be evaluated by measuring the area under the load/plastic CMOD curve of a SE(T) sample.

Jan 1, 2005

By Rob Farnfield

In the UK all new developments, including mines, quarries, tunnels, etc., are subject to a system of planning control. If the use of explosives is anticipated then such developments will attract a number of so-called ‘planning conditions’ relating to the blasting operation. This paper will outline a ‘typical’ set of conditions and how operators ‘plan to comply’. British Standards relating to both human and structural response are also reviewed and contrasted to the typical planning conditions previously outlined.

Jan 1, 2005

By John Magyar

Special foamed cements were used to stabilize and secure caving ground in a newly-reamed 12.5-ft diameter underground ventilation raise. Two zones of very poor Rock Mass Rating (RMR) material were encountered during reaming of a ventilation raise at Placer Dome's Turquoise Ridge Mime in Northern Nevada These zones caved to large cavities, continued failing, and could not be safely secured using standard rock bolting, wire mesh, and shotcrete procedures. In stable sections of the raise, the ground control plan called for the contractor to install 8-ft and 124 length resin grouted No. 7 Dywidag bolts, chain-link fence mesh and shotcrete. This work was conducted on three decks installed on the raise bore reamer. The first of the caved areas was approximately 1,500 cubic yards in volume and extended out to 40 ft beyond the wall of the raise. Placer Dome considered several options for structural fill to repair the area including pumped shotcrete, concrete, and placing and grouting aggregate. A safe, cost effective, and expedient method of stabilizing the raise with foaming grout and bolted liner plate was selected and successfully executed. The special fast-setting, foaming cement grouts used were Tekfoam and Tekseal® manufactured by Minova. The raise was quickly placed in service. Factors considered in selecting the foaming grout are discussed.

Jan 1, 2005

By C J. Adams, H J. Campbell, A J. Tulloch, I J. Graham

New Zealand can be regarded as a rifted part of mineral-prospective eastern Australia. Geologically credible comparisons between selected trans-Tasman and SW Pacific geological provinces and units, especially those that contain significant mineralisation in Australia, can help provide a useful exploration framework for New Zealand. As part of a six-year Mineral Wealth of NZ and its EEZ (MWE) research programme, we have targeted selected geological units in eastern Australia for comparison and contrast with their potential New Zealand counterparts. In future years, the programme will focus on geological units in New Caledonia.

Jan 1, 2005

By P. Magnani

Quarry environmental reclamation can be achieved with favorable economical advantages and high energy efficiency, using stabilized materials obtained by the treatment of organic fraction of municipal solid waste (MSW).

Jan 1, 2005

The underwater explosions have been used for several decades for the determination of energy content of explosives. This test method is the only one by which shock, fly rock and total energy can be measured separately. It enables to develop the energy content of explosives for different purposes; the military high explosives should contain more shock energy whereas the fly rock energy is very important feature for the blasting explosives. The purpose of this study was to establish a test place for the underwater experiments in an old water filled open pit, to estimate the repeatability of the energy measurements, to calculate the standard deviations and to compare the total energy content of commercial explosives to the theoretical values calculated by the thermo dynamical program. The test method seems to work quite well especially for the homogeneous explosives. The difference between the energy content of theoretically calculated and measured values for the homogeneous emulsion explosives was about -3% and for the dynamite about -5%. The energy difference for the unhomogeneous ANFO was detected to be -19%. The diameter of the charge was 15 cm and it was obviously too small for ANFO to detonate ideally. On the basis of the test results this test method seems to fit best for the cap sensitive, completely homogeneous, spherical charges whose masses are big enough and which are initiated from the centre of the charge. The underwater explosions as a test method is the only one which can separate shock, bubble and total energies from each other and therefore makes it possible to develop the properties of explosives for different purposes which is very important feature of this method.

Jan 1, 2005

By R A. Bearman

Recent demand pressures for iron ore should not distract from the longer term view that intense competition in the industry has demanded technological innovation of a high order. There is a long track record of successful innovation underpinned by a solid base of scientific research and knowledge. By comment on recent developments in trucks, comminution and direct smelting, this paper suggests that innovation is still a key attribute of the industry. The spending of the minerals industry on underlying science, however, is not particularly high. By looking at other industries we can ascertain that for step change technologies, it is particularly advantageous to have a solid base of science and technology underpinning developments.

Jan 1, 2005

By Larry Rayburn

Augercast piles evolved in the late forties from the process of pressure grouting open holes backfilled with stone. In 1956, a patent was issued for a cast in situ pile by pumping high pressure grout through hollow-stem, continuous flight auger as the auger is gradually withdrawn from the ground. The patent rights expired in 1973 and the use of auger-cast piles greatly expanded with most large deep foundation contractors now installing augercast piles. At one time augercast piles had a bad reputation, partly because of not having a blow count to give some engineers a confidence factor and there were some quality issues. Over the years the quality issues have been eliminated and I am sure the augercast is the most installed pile in private industry and is now being used by some State Agencies.

Jan 1, 2005

By M. Brochu

In this paper, we present a computer-vision approach developed for wall-thickness measurements of corroded pipes inspected by double-wall radiography. The main objective of the work is to optimize data collection and film interpretation using computerized image analysis. To date, the system is able to identify the inner and outer contours of a pipe and perform wall thickness measurements at each pixel of a radiograph. This will be presented by analysing pipes having different dimensions. Another important feature of the system concerns the algorithms' adaptability to pipe wall texture. In other words, image analysis is automatically refined around rough or corroded areas. This allows more precise thickness measurements and shape identification in critical sections as will be demonstrated with examples. Finally a brief overview of results exploitation will be given and compared with human interpretation. It will show the reliability of automated image analysis and the many possibilities offered by complete output analysis.

Jan 1, 2005

By W. Zheng

Pipelines can develop stress corrosion cracks in either intergranular or transgranular form. Since the mid-1980s, numerous colonies of transgranular cracks have been found across Canada and many other countries in the world. While the intergranular form of cracking has been well studied in the past 40 years, the mechanisms governing SCC in near-neutral pH environment, i.e., the transgranular form of the cracking, are yet to be understood in greater depth. Over the past ten years or so, a large number of research publications have been available on this subject and this paper summarize our latest progress in understanding the mechanistic aspect of the problem. Better understanding of the role of mill scale surface and the steel metallurgy in crack initiation has been indicated in the recent literature. However, the initiation of SCC in the lab research still relies on loading conditions that are far more aggressive than those encountered in the field. Most crack growth studies in the past are also performed under very aggressive mechanical conditions, which could have prevented the observation of environment effects. However, more recent research at lower K or Delta K ranges seems to suggest a strong role of the environment. Naturally, modeling of growth should reflect the effect of the environment, steel metallurgy, and the changing mechanical properties of the pipe steel with time. For a specific steel in a given environment, the crack growth rates tended to increase with the strain rate, indicated either by the nominal applied loading frequency or by the calculated crack tip opening rate. Future research needs to address the issue of concurrent growth of multiple interacting cracks. More attention should also be given to concurrent initiation of multiple cracks in a colony, as failure is usually caused by a coalesced crack not by an individual crack. The effect of soil environment should not be limited to the chemistry of soil solution; other factors such as cathodic processes, the variation of environment with time and physical conditions of coatings should also be considered as part of the study.

Jan 1, 2005

By Steve Kral

The upswing in prices for base and precious metals, industrial minerals and coal has allowed the global mining industry to ramp up production at existing mines and begin construction of proposed projects. In addition to satisfying shareholders, the industry is also providing good paying jobs and creating needed infra-structure in places that previously did not have either. However, the industry has learned that the prospect of jobs and infrastructure is not necessarily a guarantee that communities will allow mines to be built. The industry must maintain even higher environmental and reclamation standards. And mining companies must help communities plan for life after a mine is closed and the company moves out.

Jan 1, 2005

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By Shuangsuo Yang

Based on field observations and physical modeling of simulated materials, the dynamic equilibrium principle on the whole interaction process between the surrounding rocks and support of large deformation roadways in coal mines has been developed. It explains the methods of forming the bolted strata and its changing load capacity with deformation. It also points out the factors and conditions for forming the bolted strata as follows: (1) many entries in coal mines are subject to large deformation. During their service life, it goes through the following process, elastic > plastic > fiacture > broken > loosening, etc. During this dynamic process, the mechanisms of supporting structure are changing and therefore the interaction between support and rocks experiences a process of dynamic equilibrium. Furthermore, the required supporting force for stabilizing the surrounding rocks shows overall decreasing trend; (2) the bolted strata is a special supporting structure consisting of bolt, rock skin protection devices and rock strata within the bolted horizon. As deformation increases, the supporting structure of the broken strata within the bolted horizon experiences a process of periodic change, from equilibrium > not equilibrium > equilibrium. Corresponding to this change, the supporting capacity of the bolted strata also fluctuates and gradually decreases; (3) under the bolted strata, the stability of a large deformation roadway is dynamic and step-wise; and (4) the formation of bolted strata, especially bolted broken strata depends on the existence of compressive force. Supporting the bolted strata is not constrained by the quality of the surrounding rocks. It has broad range of application.

Jan 1, 2005

By Mutombo Nombe, Avimanyu Das, Rick Honaker

Enhanced gravity separators (EGS) provide a more efficient separation than froth flotation when cleaning coal in the 150 x 25 µm particle size range. To improve the performance of an EGS unit, air bubbles were injected into the feed stream in an attempt to decrease the apparent density of the coal particles due to the formation of bubble-coal particle agglomerates. Air injection had a significant impact on operating characteristics and separation performance. Coal recovery was increased by 10 to 20 absolute percentage points while a 2 percentage point drop in the minimum product ash content was also achieved.

Jan 1, 2005

By M. Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

Jan 1, 2005

In this paper, the use of electrochemical AC impedance spectroscopy (EIS) for in-situ diagnosis of high temperature PEM fuel cells is described. EIS was performed on single cell hardware, built in-house, using a fuel cell test station modified to operate up to 120°C and 30 psig. Electrode kinetics, membrane resistance, porous-layer and mass transport impedance of MEAs, assembled in-house, were measured at various current densities for the purpose of validating the test station and cell hardware, and for optimizing MEA and flow-field designs. The effect of temperature and humidity on the various impedances was investigated. Impedances obtained at lower and higher temperatures were compared to obtain insight into the issue of water management in operating fuel cells.

Jan 1, 2005

Level measurement of underground orepasses is important. Orepasses are not only utilised to funnel ore to the shaft skip loading station but also as silos for storing of ore in order to smooth out ore flow in a shaft system. Safety and operational efficiency are also improved as proper orepass level measurement could prevent overfilling of tipping areas. A study was therefore commenced to determine alternative technologies available as well as identifying practical installations across the Anglo American plc Group. From an instrumentation perspective an orepass system is an extremely difficult environment to take measurements in. Factors like dust, vapour, interference, bridging, wear and physical installation have to be taken into account. The study discusses time-of-flight (ultrasonics, radar and laser) measurement techniques followed by other possible solutions. These solutions included strain gauge measurement, the æjumping monkeyÆ technique, radiotomography, fibre optics and very long baseline interferometry (VLBI). Finally, various South African suppliers have been approached in order to determine instrumentation that is available for orepass level measurement in the marketplace. These recommendations were verified, where possible, by visiting the claimed installations.

Jan 1, 2005

By M. Hames, K. Larmour-Ship, B. Grinbaum, E. Buchalter, R. Hackl, B. Wassink

Sodium cyanide continues to be the lixiviant of choice for gold dissolution. Many gold ore-bodies contain a significant amount of cyanide-soluble copper which increases the cost of processing due to high cyanide consumption and high cyanide destruction and disposal costs. Several cyanide destruction processes are in use today, however, there are just a few cyanide recovery plants operating. A solvent extraction process to recover cyanide has been developed which utilizes the organophosphorous extractants Cyanex 923, di-butyl-butyl-phosphonate (DBBP) or tri-n-butyl phosphate (TBP) in Bateman Pulsed Columns. Copper cyanide species are first converted to hydrogen cyanide (HCN) by acidification, with or without sulfide addition. HCN is extracted by the organic and stripped using a suitable base (eg. NaOH) resulting in a high strength cyanide solution (eg. NaCN) for recycle to the gold recovery process. Continuous pilot plant testwork on HCN extraction using a 40 mm diameter Bateman Pulsed Column demonstrated a cyanide recovery of greater than 99% with final levels of cyanide in solution of less than 10 ppm. These results illustrate the potential of this technology to recycle cyanide and to detoxify final effluent streams.

Jan 1, 2005

By Misra M., P. Grimes, Chen. S.

The combustion of petroleum products produces emissions which contain oxides of nitrogen (NOx), hydrocarbons (HC), and particulate matter (PM) which have adverse health and environmental effects. In recent years there has been increasing interest in the use of water-fie1 emulsions as a substitute for conventional fuels. Emulsified fuels are emulsions of water in fuel, which are typically made of 10 to 20 percent of water mired with certain additives and fuel. Studies have shown that the emulsified diesel can significantly reduce the emissions of NO, PM and car- bon monoxide and increase the fuel efficiency. In order to produce a stable diesel emulsion, the development of an effective surfactant additive is critical. The stability of diesel emulsions is influenced by many factors, including size distribution of the droplets, the viscosity of the continuous phase, the physical properties of the interfacial film, and temperature. This paper describes a method to produce emulsified diesel and combustion results obtained from various tests. It has been found that the diesel emulsion made with this additive package was stable during the test, and the emissions were lower in NO, CO, and PM compared to the baseline diesel.

Jan 1, 2005