Search Documents

By John Feddock

A recent increase in energy demand has resulted in the rapid growth of coal consumption in the People?s Republic of China (PRC), which is the largest coal producer and consumer in the world. Reportedly, the safety issues in Chinese coal mines have been improving, but the number of fatalities and serious injuries continues to be alarmingly high. The number of fatalities from catastrophic accidents have prompted researchers to review the Chinese mine safety situation and to look for potential solutions. Marshall Miller & Associates, Inc. (MM&A), along with various collaborators, has investigated these issues as part of its work on various projects in the PRC and has discussed the concerns with relevant Chinese officials. Preliminary investigations by MM&A of coal mine accidents during 2001?2006 in the PRC indicate that 65%-78% of the total fatalities were the result of gas explosions and roof falls in underground mines. Even though the drainage of methane has been practiced for decades, current practices do not always produce satisfactory results due to technical constraints and equipment limitations. Based on prior experience of in-seam degasification at the Daning Coal Mine located in Shanxi province, MM&A believes that in-seam directional drilling technology can be a viable solution to degas the low-permeability Chinese coal deposits. This paper 1) reviews current Chinese coal mine safety conditions, 2) analyzes the advantages/disadvantages of current degasification practices in China, and 3) presents the pre-mining degasification practices for the longwall panel at the Daning Coal Mine.

Jan 1, 2007

By Chuck Kliche, Bill Clements

This project involved the removal of the top of an old water supply reservoir tank for the City of Lead, SD by explosives. The general contract called for the removal of the concrete top without damaging the sides or floor of the reservoir. The option of a rock hammer was eliminated, due to the possibility of an unpredictable collapse damaging the sides or floor of the reservoir. Different blasting options were discussed between the primary contractor and the blasting contractor, along with the pros and cons of each. The primary contractor settled on the option of drilling the structure for blasting versus using shaped charges

Jan 1, 2007

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

By D Craw

A glasshouse experiment was set up to investigate arsenic uptake in rye corn grown in different arsenic rich substrates. Sods of material were taken from various locations and planted with rye corn seeds. The plants grew for 13 weeks after which time the above ground biomass was harvested. Analysis of the rye corn plants showed a narrow range of arsenic concentrations, which did not reflect the arsenic contents of the soil. Comparison of the results from this study with previous work showed the glasshouse rye corn to have lower arsenic concentrations in above ground biomass than rye corn grown in field conditions. The environmental conditions present on the tailings and water-rock interactions were considered the main factors involved with the difference in arsenic uptake between field studies and the glasshouse study. This suggests that bioavailability processes are influenced by a variety of factors and cannot necessarily be predicted by the use of soil factors or glasshouse trials alone as is often done when planning phytoremediation work and mine shut down.

Jan 1, 2007

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

By Harry Verakis, Thomas Lobb

A great deal of information has been presented and published on the danger from flyrock created from blasting operations. The creation of flyrock is not specific to any one blasting operation. Flyrock is certainly not a stranger to blasting operations conducted in the mining industry and its effects are well known. Flyrock is among the leading causes of mine blasting injuries. Awareness and diligence is the message that must continue to be stressed and followed to reduce the potential for creating flyrock from blasting operations and to reduce the hazard it presents. A recent accident that resulted in a serious injury at a limestone mine in Pennsylvania bears witness to the ever-present danger of flyrock created from blasting operations.

Jan 1, 2007

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160ºC and 1,380 kPa (200 psi) oxygen overpressure, DEW to produce LME Grade A cathode, recycling of the lean electrolyte to the pressure leaching step and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of the lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an ?acid-autogenous? process referred to as the ?MT-DEW-SX? process. This paper (Part III) discusses the steps taken to develop and complete a large-scale demonstration of the process at Bagdad, Arizona, in 2005.

Jan 1, 2007

There are presently no suitable underground mine production scheduling optimisation models available for application to sublevel stope mining. Scheduling underground production for maximum return is therefore still a manual process, which generally involves scheduling production from the next available highest cash flow stope within the operational constraints of the project. In most mining operations, the scheduling problem is too large and complex to guarantee truly optimal results through manual scheduling. This paper reviews some general optimisation studies that have been proposed for underground hard rock mining. Furthermore, an example of a mixed integer programming model is presented for a small conceptual sublevel stoping operation. Comparative results of a schedule generated by a mixed integer programming (MIP) production scheduling model and a manually generated model on a nine stope example is presented. Results indicate that the potential benefits of the MIP production scheduling model for the purpose of maximising NPV are significant. Finally, a new constraint was formulated to limit multiple exposures of fill masses for use in an existing MIP production scheduling model. Testing of the formulation took place on the central stope of the nine stope example, which showed that the formulation performed its task without breaking other operational constraints.

Jan 1, 2007

Namakwa Sands, an Anglo Operations Limited subsidiary, is a world-class producer of heavy minerals. A layer of duricrust imposes a pseudo-stratigraphy to the primary deposit and has sterilized part of the generally unconsolidated ore in the open cast mine. The bulk of this ore cannot be treated by the present infrastructure, which employs conventional mineral separation technology. The mineralogy of the cementing agent consists of magnesium and calcium silicates and minor carbonates in addition to clay minerals such as sepiolite and those from the smectite group. Although the duricrust ore is friable and can be easily crushed, the significant clay-sized slime fraction produced, in particular the highly sorptive sepiolite, adversely affects mineral separation. The geometallurgical challenge is to cost-effectively remove the slimes from the ore before it is delivered to the concentrator.

Jan 1, 2007

By D M. Aranha, M A. Fonseca, M Echtern

The regional syndeformational metamorphism affecting the Itabira Iron Formation (IIF) at Quadrilßtero Ferrffero (QF) was formerly discussed by Dorr (1965), who proposed that quartz grain size could monitor the metamorphism, according to James (1955), and that the formation of haematite could be the result of the synchronous metasomatic process. Herz (1979) suggested the existence of three metamorphic zones, not mentioning the haematite formation. It could be observed that the primary oxide phase in the IIF is magnetite and most of the hard haematite was derived from the metamorphic replacement of magnetite, forming micaceous or schistose haematite. Differently from most iron formations in the world, the formation of haematite deposits at QF occurred under high oxygen fugacity during metamorphism. The haematite microlaths display a strong preferred orientation, which determines the alongated shapes of the fragments. The terms foliated and unfoliated haematite have been applied by Dorr to the micaceous or schistose haematite, and to the isotropic, hydrothermally derived haematite. Under the microcope, the haematite exhibits a strong crystallographic or lattice orientation encircling the magnetite and martite porphyroclasts. The strain rate determined and defined the textural variation, size and economic importance of the deposits and the ore grade. Metamorphism at QF increases eastward and resulted in the formation of a gruneritic Fe-Mg amphibole, at the western portion, followed by a cummingtonitic amphibole at the central-western part, succeeded by the actinolite zone at the central-eastern part, and finally to the tremolite-anthophyllite zone to the east. These zones, arranged in a north-south pattern, can be followed in the pelitic units, whereas appear sericite-chlorite, kyanite-chloritoid and garnet-staurolite respectively. Carbonate geothermometry in IIF also may support the metamorphic variations. At the western zone the haematite forms small lenses within the itabirite, P-contents are slightly higher than in the remaining IIF, haematite grain size is minute, resulting in a submicaceous texture and the amount and dimension of relict magnetite within haematite is greater than in the other parts of QF. Jangada and Serra Azul deposits are examples of this zone. The central-western zone is characterised by significant haematite deposits, in considerable quantity and size, haematite grain size increased, in order to produce a micaceous texture, the P-contents and the amount of magnetite decreased. Pico do Itabirito, Cappo Xavier, Capitpo do Mato and Tamanduß correspond to the deposit type of this zone. At the eastern-central portion the amount of the hard haematite deposits decreases, increasing the soft haematite ore due to higher strain rates. However, it can be perceived that the relict magnetite almost disappeared and the haematite grain size became coarser than the haematite from the western zones. At the eastern zone, the haematite deposits exhibit typical schistose texture, the magnetite porphyroclasts are absent and the lowest P-grades in the haematitic iron formation. The haematite bodies characteristic from this zone are Andrade, Morro Agudo and the deposits at the Itabira District. The hydrothermally derived compact and isotropic haematite deposits, formed subsequently to the micaceous haematite bodies, were generated after deformation ceased, but under very high fluid pressure. The metamorphic reactions magnetite + quartz + H2O = grunerite + haematite and magnetite + quartz + H2O = grunerite + O2 were decisive in the formation of the metamorphic haematite deposits.

Jan 1, 2007

By R Rodriguez, S Gumo

The Lihir Gold Mine, in Papua New Guinea, is a large open pit operation within an active geothermal system inside a collapsed volcanic crater. This unique setting has a big impact on the mine operation because of the occurrence of geothermal hazards. The system for managing geothermal hazards that has been developed by Lihir Gold Mine is a pioneering effort that can be applied to future mine discoveries in a similar environment. The controls are integral to the mining operations and allow mining to proceed whereas without them mining could not be considered. Truck and shovel productivities in conventional open pit operations are constrained by diggability, equipment availabilities and utilisation. At Lihir, additional constraints are in the form of 100 m exclusion zones around working shovels and 50 m exclusion zones around working drills. Given that the mine has seven large digging units and six drills, this amounts to a lot of area that excludes the presence of people on the ground. So how are the necessary work like grade control, survey, blasthole loading, and in-pit maintenance performed safely to achieve production targets? The answer is in the highly specialised procedures that have been developed that utilise geological, geothermal and geotechnical knowledge to predict problem areas and also deal with the organisation of movement in the pit for people and mining equipment. This paper will detail how scheduled material movement can be maintained despite the challenging conditions faced at Lihir Gold Mine.

Jan 1, 2007

By Kenneth Eltschlager

Post-blast assessment techniques using off-site data which includes location, seismograph and photographic data were discussed during the Blaster’s Weekend at this year’s ISEE Conference. Blast and property locations with commonly available GPS units allow for the spatial relationships surrounding the blasting to be documented. When distances are coupled with the charge weight per delay, the scaled distance can be calculated to any structure for either compliance with the rules, or to project limitations. When blasting seismograph data is obtained, the scaled distances are then able to be plotted against ground and air vibration levels for post-blast assessment purposes.

Jan 1, 2007

By Wilfrid Comeau

Vibrograms, which last significantly longer than the actual blast (say 10 to 15 cycles or more), may be signalling an elastic response, which is not uniquely blast related. For example, geophones mounted on a part of a structure, which can elastically resonate at a frequency included in the seismogram, may not show the structure’s real reaction to the blast. This resonance usually amplifies the ground vibration. This contribution examines one particular case where blasting excited and amplified a resonant ground response, and the method used to significantly reduce or eliminate this undesirable condition.

Jan 1, 2007

By W. Mackenzie

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines - mining, metallurgical, chemical, civil, electrical, mechanical and environmental - as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies - and hence no two development projects - are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource project's development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as `doing a feasibility study'. But the principal purpose of a `feasibility study' is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant - they are a prerequisite to the demonstration of a project's viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of `feasibility studies' and provide guidance to minimum standards and best practice.

Jan 1, 2007

By P. M. Godinho

The debut of the sustainable development concept in the political arena, and the publication of Our Common Future in 1987, represents the starting point of present concerns and efforts associated with the sustainability of the ecosphere and its ecological and human subsystems. The sustainable production and consumption of natural resources, in particular mineral resources, represents a central aspect of the problem. In this context, an important goal has been to develop sophisticated management systems, which consider sustainability principles, in organizations within the system of minerals and metals (SMM). The development of indicators is only part of this challenge. The extractive industries (EI) as an important stakeholder of the SMM (should) have similar priorities. If embraced, this challenge offers great opportunities, one of them being the potential for advancing the understanding of how these organizations learn and change. The identification of its main determinants offers, in theory, the possibility for their management and a faster achievement of the sustainability levels to which they (should) aspire.

Jan 1, 2007

By M. Moats

World copper refining tankhouse practices have been surveyed. This survey is a supplement to previous surveys that have been carried out in the 1987, 1991, 1995, 1999, 2001 and 2003. On a world basis, process technology trends include the further installation of automated electrode handling systems including permanent cathode systems, automatic anode preparation and cathode handling machines, section switches, fully automatic cranes and polymer concrete cells. General plant process control has increased with more automation of material handling in the copper refining tankhouse. The general trend for most greenfield copper refining projects remains in eastern Asia.

Jan 1, 2007

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the projectÆs gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the LendersÆ and BorrowerÆs teams has facilitated a greater understanding and æownershipÆ of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

By Z. Nivolianitou

This article aims at highlighting the importance of technological innovation, namely the potential use of Virtual Reality (VR) technology, as a Sustainable Development Indicator for the minerals industry. Nowadays, VR is regarded as a mature technology for real world representation, and it has been already applied in various domains such as architecture, topography, aeronautics, medicine, and lately in the process industry. Several industrial sectors already use VR tools, as the car industry for improving car ergonomics and design and the aviation industry for both pilot and maintenance crew training. It is well known that the mining industry, as well as the process industry, requires people to work in hazardous environments and situations, often inadequately trained owing to limitations in time and resources, building thus the potential for minor or major accidents.

Jan 1, 2007

By Colin Lawrence, Michael S. Schultz

Due to the planned deepening of the NY Harbor, NYCEDC/NYCDEP is planning to replace two existing water lines between Brooklyn and Staten Island with one deeper water pipe. The crossing, just north of the Verrazanno Bridge is 1.75 miles long. The new pipeline will be tunneled using gasketed concreted segmented liners. Apressurized face machine will be used through the soft ground. This will be the first subaqueous application using this technology in New York City. This paper discusses the planning, design and risk issues associated with the crossing and the challenging soil conditions that resulted in the decision to use a pressurized face machine.

Jan 1, 2007

By K. Eklund, T. Ahokainen

The Flash Smelting process is the most used production method for primary copper in the world. The basic idea of the Flash Smelting is to utilize the thermal value of sulfidic concentrates and melt the reaction product, in controlled conditions, without a need for external energy. This basic principle is utilized both in matte smelting and in Direct-to-Blister Flash Smelting Processes. In this paper, the behavior of normal (CuFeS2) concentrate of FSF-process is compared to the behavior of high grade feed material produced by Outokumpu Concentrate Upgrade Process with the aid of computational fluid dynamics (CPD) simulation using add-in subroutines developed by Outokumpu Technology. Results consist of the information concerning the behavior of the suspension, reaction efficiency and other parameters concerning the reactions of the feed material. It will be shown that, using the Upgrade Process, the throughput of copper from the Flash Furnace can be almost tripled.

Jan 1, 2007