Search Documents

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

It is suggested in chapter 1 that emergency activities (including escape) are not individualistic. They tend to be group responses. If escapes from mine fires are group activities, then preparation for such events must take group behavior into account. This chapter explores the hypothesis that the miners who escaped from the three mines under study did so as members of groups. For development of this chapter, the database was examined for evidence of the existence of escape groups and for instances when individualistic behavior was paramount. Illustrations of group and/or individualistic behavior were analyzed and representative examples are provided in the following discussion. The nature of groups was discussed in chapter 3 and the following working definition was offered: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at second-hand, through other people, but face-to-face" [Homans 1950]. To determine whether or not groups existed during the fire evacuations, it is important that the concept of group be clearly defined. Therefore, the discussion started in chapter 3 will be elaborated here. The defining characteristics of group given in chapter 3 were taken from Homans [1950]. They include size, person-to-person com¬munication, feelings that members have for each other, explicit and implicit rules for behavior, and common activities. An additional characteristic that is sometimes used to define groups is cohesiveness. Kiesler and Kiesler [1970] state, "Cohesiveness would include not only the attraction that the group holds for its members but also any other force operating on the individual to stay in the group." Variables said to contribute to cohesiveness include "(1) the attractiveness of a group for its members," and "(2) the coordination of the efforts of the members" [Keisler 1970]. One source of the attraction to a group occurs when "the goals or exterior tasks confronting the group are consistent with those of the individual person, and can best be handled by group action" [Cartwright and Zander 1968, in Davis 1969]. In other words, a common goal and a coordinated effort mounted to achieve that goal contributes toward the creation of a cohesive group. As discussed in the earlier review of research (chapter 1), groups have frequently been studied in laboratory or simulation settings. These methods allowed control over variables of interest. Kiesler and Kiesler [1970] state, however, that they "find group variables conceptually imprecise and experimentally difficult to work with." Experimental control, in other words, is difficult to achieve in the study of groups. The richness of the naturalistic mine fire data may provide an opportunity for an examination of groups that cannot be found in laboratories or simulations because this environment was not

Jan 1, 2000

By Reis. E., P. Pino Véliz

"Along the process of defining the fundamentals of a ferronickel project, several questions require proper answers from the very beginning such as the size and characteristics of the laterite deposit (oxide or silicate), the mineralogical variability, and the selection of the most valuable process route. In general, these elements will be defined along the progress of the exploration and feasibility studies, and definitive engineering. Also, from the very preliminary estimates, three questions are very common: what should be the plant capacity (annual tonnes of contained nickel), what will be the probable capital required (CAPEX), and what will be the estimated timeline (schedule) between the initial stage, say the feasibility study and the plant start-up and ramp-up to designed capacity. The accuracy of the capital cost estimates also progresses along the different stages of development from ±50% at the Preliminary Economic Assessment (PEA) stage down to ±5% for the Detailed Engineering and Construction stage. These accuracies of estimates have been, in some ways, accepted by the mining community and investors. The industry accepted benchmark for ferronickel projects in terms of CAPEX are then in the order of US$50,000 per tonne of nickel contained in the FeNi product. In this paper, the authors analyze in some details three ferronickel projects for lateritic ores that have selected the Rotary Kiln - Electric Furnace (RKEF) as the suitable technological route and have started production in the period 2006–2016. Some key aspects of the ferronickel projects are examined: 1) size and type of deposit; 2) flowsheet selection; 3) evolution of capital cost as a function of capacity from the feasibility stage to construction; 4) comparison between planned production scale and actual ramp up; 5) estimated capital expenditure (CAPEX) compared with actual figures; 6) nickel price evolution and timing of the approval for the project to proceed to construction and production start-up. The objective of this paper is to identify key elements that should be addressed in future projects and that are proposed as benchmark figures for similar projects."

Jan 1, 2017

By Fred Wright

IN A recent paper1 a detailed discussion is given of the possibilities. of using polarized light in the examination of opaque substances. The factors underlying the problem .are there treated from the viewpoint of the electromagnetic theory of light and the presentation is necessarily mathematical in form. The practical methods resulting from the discussion are, however, relatively simple and promise to be of value in the determination of certain ores and metals when studied in reflected light under the microscope. The results of the theoretical investigation referred to may be summarized by stating that in general the optical constants, such as refractive indices and absorption indices, cannot be satisfactorily ascertained on small, random, polished sections; that the use of polarized light enables. the observer ordinarily to determine whether the crystal plate is isotropic or anisotropic, and also to ascertain the degree of anisotropism; that for this purpose methods based either on the contrast in intensity between the two reflected components of non-polarized light, or on the amount of rotation of the plane of polarization, on reflection, of vertically incident, plane-polarized light, may be employed; that methods based on the phase difference between the two reflected components are in general of little value because of the small differences in phase which ordinarily result for a relatively large change in birefringence or biabsorption. The measurement of the optical properties of transparent minerals, even in minute irregular grains, is a simple task with modern petrographic microscope methods and is accomplished by petrologists as part of their ordinary routine work. But the determination of the optical constants of opaque substances is difficult and is rarely attempted; all observations are necessarily made in reflected light and are restricted commonly to the determination of color, of hardness, of the character of crystallization, and

Jan 2, 1920

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

By Michael S. Moats, Alex Luyima, Tomas Oliveira

Some commercial copper electrowinning facilities use Cyquest N-900 (a polyacrylamide) or HydroStar (a modified polysaccharide) to improve the density and smoothness of copper electrodeposits. However, the effects of these additives have not been studied extensively in the open literature. Thus, the electrodeposition of copper at 40 oC from a non-stirred synthetic electrowinning electrolyte (40 g/L Cu2+, 160 g/L H2SO4, and 20 mg/L Cl-) in the presence of various concentrations of either additive was evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). CV results show that neither additive has much effect on the nucleation overpotential of copper electrodeposition on stainless steel. However, Cyquest N-900 polarized the copper deposition reaction upon the return sweep. The EIS data indicates that Cyquest N-900 increases the reaction’s charge transfer resistance and creates a second low frequency loop. HydroStar had minimal effect on the electrochemical data generated by CV or EIS. Thus, the mechanism by which HydroStar affects the copper deposition reaction still needs to be determined.

Jan 1, 2014

By B. R. Stewart

The exclusion of coal fly ash from regulation as a hazardous waste has led to increased interest in returning ash to the coalfields for co-disposal. A multi-year column study used coal refuse with high potential acidity (4% total-S), and two alkaline ashes in various bulk-blends. The unamended refuse acidified rapidly, producing acidic (pH 1.7) leachates, high in dissolved metals. Treatments blended with sufficiently high amounts (20 to 33%) of alkaline ash produced alkaline (PH >8.4) leachates with low metal levels, while lower ash blending rates acidified over time to produce metalliferous leachates. Examination of solid materials indicated that pyrite oxidation was occurring to some extent in all treatments. A regression equation (r = 0.95) was developed to estimate time to net acid release for mixtures of these materials. Ash alkalinity and refuse potential acidity must be balanced to insure water quality for co-disposal environments, or the ash materials should be isolated away from acidic drainage waters.

Jan 1, 1997

By B. R. Stewart, L. W. Zelazny

The exclusion of coal fly ash from regulation as a hazardous waste has led to increased interest in returning ash to the coalfields for co-disposal. A multi-year column study used coal refuse with high potential acidity (4% total-S), and two alkaline ashes in various bulk-blends. The unamended refuse acidified rapidly, producing acidic (pH 1.7) leachates, high in dissolved metals. Treatments blended with sufficiently high amounts (20 to 33%) of alkaline ash produced alkaline (pH >8.4) leachates with low metal levels, while lower ash blending rates acidified over time to produce metalliferous leachates. Examination of solid materials indicated that pyrite oxidation was occurring to some extent in all treatments. A regression equation (r2 = 0.95) was developed to estimate time to net acid release for mixtures of these materials. Ash alkalinity and refuse potential acidity must be balanced to insure water quality for co-disposal environments, or the ash materials should be isolated away from acidic drainage waters.

Feb 24, 1997

By H. Marquis

This paper is concerned with an analysis of a number of failures of large-size, hypervelocity light gas gun chambers and barrels. A brief description of the light gas gun principle and of the various types of guns is first given. The failures and the investigations carried out are then described in detail, with the failures divided into two groups. The first group comprises those failures caused by certain conditions to which the guns may be submitted, and includes, for example, severe local heating of the bore surface causing hardening and cracking of the steel. These conditions were accidental and steps were taken to prevent them. The remaining failures were due to faults in the material or in the heat-treatment, manufacturing or assembling procedures. Specific problems, such as hydrogen embrittlement, and the use of high strength gun barrels above their ductile-brittle transition temperature by preheating prior to firing, are briefly considered. Some interesting observations are also presented on the use of surface markings, and angles of fracture of large fragments, as an

Jan 1, 1962

By Mark Board

INTRODUCTION As the world's supply of near-surface metalliferous ore bodies is depleted, more emphasis must be placed upon mechanized bulk systems of underground mining. In particular, block caving is becoming increasingly important as a method of mining low to moderate grade deposits at depths of somewhat less than 1219 m (4000 ft). 00 ft). The block caving method requires that the ore body be completely undercut, thereby removing its means of support and inducing failure which progresses from the undercut to the ground surface. As the span of the under- cut increases and the weight of the overlying crushed ore body becomes greater, large stresses are induced on slusher and haulage drifts. Stability of these drifts is critical in block caving operations and often proves to be an extremely difficult task (Kendorski, 1976; McWilliams, 1975). Slusher drift maintenance can be costly, often exceeding that of the original support costs. This chapter analyzes the ground support problems of an Arizona block caving mine. The mine presently uses monolithic concrete liners as a support method. Failure of the liners occurs as the undercut approaches, thus initiating a maintenance problem which will continue until the ore body is depleted in that block or panel. To examine this problem, a simple analysis of the stresses induced by the advancing undercut was per- formed. Utilizing a design method developed by Dixon ( 1973, 1974), the calculated stresses were used to deter- mine the minimum thickness required for varying section shapes of unreinforced concrete liners. It is found that the thicknesses required for stable linings are not economic. Recently developed empirical methods of support de- sign are utilized (Barton, 1974; Bieniawski, 1973) and compared to the analytical method. A final discussion of alternative methods of support is given with recommendations for the use of passive or "yielding" support methods. LAKESHORE MINE (GENERAL GEOLOGY) The Lakeshore copper property is located in Pinal County, AZ, approximately 45 km (28 miles) south of Casa Grande. The Lakeshore deposit is a porphyry cop- per similar to others in Arizona. The ore body consists of disseminated chalcopyrite and fracture fillings in quartz monzonite porphyry (QMP), Cretaceous volcanic (KVS), Precambrian diabase, and Mescal limestone. The ore body has been divided into three distinct zones of mineralization which have been termed (South, 1972) the oxide zone, the sulfide zone, and the tactite zone. The oxide zone occurs in the upper portions of the ore body and consists primarily of leached and oxidized quartz monzonite porphyry and Cretaceous sedimentary and volcanic rocks. The sulfide zone underlies the oxide zone and includes all quartz monzonite porphyry and Cretaceous rocks which have not been oxidized. The thickness of the sulfide zone is variable and ranges from about 61 to 122 m (200 to 400 ft). The tactite zone occurs in a series of Paleozoic metasediments consisting of tactite, quartzite, diabase, hornfels, and dikes of quartz monzonite porphyry. The tactite zone is highly variable in thickness and underlies the Cretaceous volcanic and sediments throughout the mine. Together, the tactite and sulfide zones are known as the thick or tall sulfides. The greatest support stability problems occur in mining of the tactite zone and are therefore the subject of the remainder of this chapter. MINING METHOD The Lakeshore mine is a block caving mine utilizing a panel caving method. The present mine consists of two

Jan 1, 1982

By Graham Andrews

Experiment shows that the microbial degradation of pyrite does not necessarily proceed stoichiometrically. Under some conditions sulfur is oxidized preferentially leaving something approaching iron in composition; under others, the pyrite is converted almost to elemental sulfur. A kinetic model for the process based on three elementary biochemical reactions can explain these observations. The diffusion of sulfur along grain boundaries and dislocations in the solid pyrite uncouples the oxidation rates of sulfur and iron from the requirements of stoichiometry. This mechanism also explains qualitatively why bacteria adsorb preferentially at dislocation sites on pyrite surfaces, why they form "pits" at these sites, and why amorphous pyrite is more readily degraded than pure crystals. The rate-limiting step for pyrite oxidation is discussed

Jan 1, 1989

By R. D. Lrwin, W. M. Mullins, S. Venugopa, J. C. Malas

"Physical models for acoustic emission (AE) are introduced and expressions are derived to predict AE activity from such parameters as applied stress, strain and strain-rate. These models are then incorporated into a visco-plastic finite-element simulation program, and the acoustic emission event rate generated during metal forming operations are predicted. Simulation results are presented for upsetting operations on a typical C-Mn type steel for various friction and die geometry conditions. The AE model predictions compare well with the limited available experimental results reported in the literature and demonstrate that AE signatures can be reliably simulated. The signatures predicted for metal forging are fairly insensitive to processing parameter changes. This suggests that AE event rate monitoring may not be well suited to process monitoring for forging. However, the size of the features is conjectured to influence the frequency content of the AE signals. Thus, since current simulations include only the ability to predict the number of events for a set of processing conditions, future work is required to simulate the duration and magnitude of acoustic events. Fourier analysis techniques may then be applied to investigate correlation with microstructural features.IntroductionThe open loop control system method for deformation processing design, as described by Malas et al. [1 ], consists of several steps in series to achieve the final design. The first step uses microstructure development models to determine the optimum deformation path to achieve the desired final microstructure. The second step, the process model, calculates the processing parameters required to achieve this deformation path. Finally, the metal-working system uses the required processing parameters to produce the part. Figure 1 shows this in block diagram form"

Jan 1, 1997

By O Omidi

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper reviews previous experimental information and presents the results of new tests conducted in small blocks constructed using a commercial grout. The effect of the delay on the average fragment size, coarse fragmentation and uniformity of fragmentation is discussed. Fragmentation was coarser at extremely short or extremely long delays, while a fairly constant average size was obtained at a variety of intermediate delays. Uniformity, defined as the slope of the fragmentation distribution through the average fragment size, was poor at short and very long delays and relatively constant at the intermediate delays. Some tests attempted to minimize the effect of gas penetration by lining the boreholes with copper tubes. When this was the case average fragmentation changed marginally, while uniformity was significantly affected by delay and was typically smaller than in the unlined tests.

Jan 1, 2014

By T Raynlyn, J J. Campbell, J M. Young

In order to correctly predict the performance of beneficiation processes, such as hydrocycloning or ultrasonic treatment of iron ore fines, it is important to understand possible changes in size distribution, mineral composition and textural peculiarities. During beneficiation processes, iron ore can be subjected to various physical actions which may result in changes in size distribution. In the case of soft or friable ores, attritioning and/or deagglomeration may have a significant effect on both separation performance and product stream specifications. Optical image analysis tools, which give statistical information on a particle by particle basis, can help in better understanding the response of the ores to these processes. An experimental study has been conducted to investigate the response of a haematitic-goethitic iron ore to a combination of stirring and ultrasonic treatment. The effect of stirring and ultrasonic treatment on the size and mineral distribution has been quantified using image analysis and automatic ore texture classification. This approach has been applied to several size coarse fractions of the initial feed and product. The results show that, following treatment, the mass proportion of ore texture classes which contained higher amounts of ochreous goethite and kaolinite had significantly decreased compared with that in the feed, while the proportion of texture classes where haematite was the major mineral had increased. Liberation analysis also showed a significant increase in the proportion of particles with more than 95 per cent haematite and vitreous goethite.

Jan 1, 2007

By R. W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from nonkimberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques where spectral bands are chosen to optimize contrast between the kimberlitic soils, nonkimberlitic soils, and vegetation. Careful processing of the multispectral data is essential to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1986

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sink times were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1% and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying and dumping of coal products by comparison to airborne dust capture from sprays.

Jan 1, 2013

By John E. Urosek, Jack E. Tisdale

The Mine Safety and Health Administration (MSHA) has developed a Mine Ventilation Bleeder and Gob Training Course. This three day course is designed to increase the knowledge and understanding of bleeder ventilation systems. It discusses concepts, designs, plan approval, inspection and evaluation of bleeder systems. This paper will introduce some of the material contained in that course, focusing on the inspection, examination, and evaluation of bleeder systems. The regulations addressing the use of bleeder systems are found in Title 30 Code of Federal Regulations (30 CFR) Section 75.334. The examination requirements are found in 30 CFR Section 75.364. Section 75.364 de- scribes specific locations where examinations are to be made and specific information to be gathered at those locations. The required locations and information will be discussed in some detail with examples and illustrations. These weekly examinations for bleeder systems are designed to monitor the parameters of the bleeder system and to evaluate its effectiveness. Over time, conditions can develop in the bleeder system that affect the ventilation and lead to hazards such as methane accumulations. The hazards of methane accumulations need to be understood as such accumulations can contribute to mine explosions. The importance of additional information gathered by the mine examiner that can assist in evaluating the performance of the system will also be discussed.

Jan 1, 1997

By James Donald Forrester

JAMES DONALD FORRESTER 32.1-EXAMINATIONS The field examination of a mineral deposit or mining enterprise requires a comprehensive effort to determine all natural and man-made factors bearing upon the problem to be resolved by the investigation. Therefore, the purpose to be served by an examination must be fully understood before the engineer assumes responsibility, and before actual field work starts. A clear understanding facilitates planning the approach to the project for maximum efficiency and thorough acquisition of information. It follows, of course, that the engineer has the necessary knowledge and experience to discharge satisfactorily the professional obligations attending the project. Some studies are in herently more complex than others, and the requirements of the problem are not always the same. Some examinations require the detailed investigation of large operating or nonoperating mines or, possibly, of mining districts; others involve more or less reconnaissance studies; and still others rela¬tively small undeveloped mineral occurrences. Likewise, the primary objective of some analyses may be the evaluation of a mineral deposit or a mining property, whereas in other projects the major objective may be guiding mining or drilling work in the discovery of new or hidden ore bodies and mineral-bearing structures. Thus, the possible range of any given examination may extend in varying degree through one, or more, of the following types of procedures: 32.1.1--GEOGRAPHIC ENVIRONMENT Studies of geographic environment should be made to ascertain the general physical situation in the area under consideration and to identify those correlative factors hearing on the, findings resulting from the field examination. This commonly will include determinations of: A. Location of the field area with respect to the state and county in which it occurs and, if feasible, a record of the township, range and section with reference to the principal meridian, and base line (or lines) that apply. For examinations in foreign countries, or in regions outside the continental United States, it is desirable that the field locality, in each instance, be identified with reference to the boundaries of some form of political entity essentially comparable in character to the divisions used in the United States. B. Distances from existing communities and related service centers, via: 1. Roads, both improved and unimproved. 2. Railroads. 3. Navigable waterways. 4. Airports. C. Topographic relief as it will influence the selection of 1. Pit site or positions of underground mine portals or shaft sites, including dump areas. 2. Mill site, including tailings disposal area.

Jan 1, 1973