Search Documents

By S. K. Bhatt

This paper reviews major developments in continuous haulage technology for underground coal mines. Haulage systems in use and development are investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, multiple- unit continuous haulage, extensible and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine being developed by the US Bureau of Mines. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1991

By S. K. Bhatt

This paper reviews major developments in continuous haulage technology for underground coal mines. Haulage systems, both in use and development, are investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, multiple-unit continuous haulage, extensible, and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine being developed by the U.S. Bureau of mines. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1990

By Lennox A

In an attempt to increase underground productivity Coal and Allied has introduced a continuous haulage unit into it's Moonee colliery. A second unit is planned for Nallarah colliery in the near future. Both systems will be roof mounted or monorail type and manufactured by Joy Manufacturing Pty Ltd. The introduction of these machines is seen as a logical step in improving the efficiency of mining with continuous miners. This could be in conjunction with longwall mining in the rapid development of gate roads or, as in the case with these machines, as conventional development and extraction units. The advantages of the continuous haulage system are; Relatively low cost. 2 Ability to obtain high productivity in irregular or disturbed coal reserves not suitable for longwall mining. 3 Increased worker safety with the elimination of shuttle cars and the majority of trailing cables. 4 Increased productivity independent of soft or difficult floor conditions. At the time of writing the Moonee installation is 6 months old. The Nallarah machine is due for delivery March 1988.

Jan 1, 1988

By William D. Mayercheck

Beginning in 1974, the Bureau of Mines, U.S. Department of the Interior, sponsored R & D efforts related to further development and use of continuous face haulage in underground coal mines (Cowan, 1975). The U.S. Department of Energy continued this effort as of October 1977. This paper represents an update of an article previously published in Mining Engineering magazine (Mayercheck, 1979). Development progress is summarized for a variety of prototype systems or components now being built, surface tested, or tried underground.

Jan 1, 1981

By W. D. Mayercheck

Beginning in 1974, the Bureau of Mines, US Department of Interior, sponsored research and development efforts related to further development and use of continuous face haulage in underground coal mines (Cowan, 1975). The Department of Energy continued this effort as of Oct. 1977. This paper represents an update of an article previously published in Mining Engineering magazine (Mayercheck, 1979). Development progress is summarized for a variety of prototype systems for components now being built, surface tested, or tried underground.

Jan 1, 1984

By T. A. McAfoose

As one of the major suppliers of the chestnut Ridge energy center, Rochester and Pittsburgh Coal Company continues the search for more efficient haulage systems. This search is one that is essential in providing coal to the Keystone and Homer City power plants at the most economical cost. These two electrical generating plants located in west central Pennsylvania are part of the energy center which consists of four generating stations. Prior to the time the two stations were put on line, August, 1967 for Keystone and August, 1969 for Homer City, our company made the decision to rely on belt conveyors from the section to the surface to provide for continuous main line haulage. The proximity of these generating stations to proven reserves allow for minimal truck haulage and minemouth setups. With the addition of seven new mines, in the past ten years, revisions have been made on the original setup to interconnect the haulage of several mines to deliver the product by belt to the power plants.

Jan 1, 1979

By Bo Arvidson

SALA MAGNETICS, INC. is now operating a 15 tph continuous high gradient magnetic separator, the SALA-HGMS® Mark III Carousel, as part of a complete mineral processing pilot plant installed at Sala's Cambridge headquarters. The Mark III can generate a maximum magnetic field of 18 kG making it possible to process even weakly magnetic, finely ground ores and ore tailings on a continuous basis at the performance level achieved in Sala's cyclic high gradient magnetic separators. Test results on iron ores, clay, and decoppering of molybdenum concentrate will be discussed. Bench scale tests have been performed on all of these materials using the SALA-HGMS® Model 10-15-20 Cyclic Magnetic Separator. A direct correlation may be made between cyclic and carousel results. Sala's Mark III Carousel high gradient magnetic separator is designed to permit scale-up to machines capable of processing two hundred (200) tons of ore per hour and more.

Jan 1, 1976

By Tadafumi Adschiri

"Supercritical water can provide an unique reaction atmosphere for synthesizing metal oxide nanoparticles. Due to the drastic change of properties of water around the critical point, including density, dielectric constant and ionic product, the reaction phase with O 2 or H2 gas and the reaction rate and equilibrium can be varied to synthesize new materials or define particle morphologies. In this work, hydrothermal crystallization experiments are performed with several types of flow apparatus that allow convenient manipulation of variables such as temperature, pressure, and residence time. Key features in the flow modes and material preparation are discussed. The proposed supercritical hydrothermal synthesis method has the following desirable features: i) nanoparticles can be produced, ii) morphology of the produced particles can be controlled with small changes in pressure or temperature, and iii) a reducing or oxidizing atmosphere can be applied by introducing oxygen or hydrogen or other gases. An overview of this method is given for functional material synthesis of significant industrial interest including barium hexaferrite magnetic particles, YAO/Tb phosphor fine particles and lithium cobalt fine crystals.IntroductionHydrothermal crystallization, a method of metal oxide formation from metal salt solutions, is typically used at temperatures ranging from 373 K to 473 K. We are developing a new process for hydrothermal crystallizations that uses temperatures in the range of 673 K to 723 K, which is just above the critical temperature of water1 • 8 • In this work, we refer to this process as supercritical hydrothermal synthesis. The supercritical state of water allows one to vary reaction rate and reaction equilibrium by shifting the dielectric constant and solvent density with pressure and temperature. From of our research on material production in supercritical water, we have identified the following specific features of the supercritical hydrothermal synthesis method: (i) ultrafine particles can be produced, (ii) morphology of the produced particles can be controlled to some extent with pressure and/or temperature, and (iii) a homogeneous reducing or oxidizing atmospheres can be provided by introducing gases, such as O 2, H2, H2O 2• and so on.1"

Jan 1, 2000

By Ehlert G, Steinlechner E

The paper describes a new process for filtration which combines the continuous operation of conventional vacuum filters with the low final moisture contents hitherto only achievable with plate and frame presses. The increasingly high portion of fine particles causes several problems in the filtration of copper concentrates. One drawback is that remarkable quantities of liquid are attached to the very fine particles because of their specific surface area. Furthermore, fine particles also reduce the size of the capillaries in the filter cake, thus increasing the critical pressure which any filtration system has to exceed to achieve the desired final cake moisture. The maximum filtration pressure of conventional vacuum filters is limited by nature itself and by practical aspects to approximately 0.75 bar. The hyperbaric filter combines the continuous operating principle with an increase in filtration pressure of up to 6 bar simply by placing the entire disc or drum filter inside a pressure vessel. The major machine components and process features are explained in the details of the paper. After extensive research and field testing, 23 ANDRITZ hyperbaric filters, with a total filtration area of 1968 m2 have now been sold. Seventeen of these units (1440 m2) are in commercial use and more units are, on order. Performance data on copper concentrates from plants in Australia, South America, Poland, Africa and North America are outlined in detail. Compared to vacuum filters, generally hyperbaric filters will reduce the final cake moisture of concentrates with 75 per cent

Jan 1, 1993

By G McMillan, P Mulvey

"Geochemical characterisation is done based upon the geology and metallurgical batch testing prior to commencement of the operation of the plant.  Tailings repository design is based upon geochemical assessment of the waste material, as well as the geomechanical issues associated with storing the waste. The resultant conceptual and detailed design is incorporated into the environmental impact statement (EIS), upon which mine approval is based. The entire environmental monitoring and harm mitigation program, which is usually a condition of the Mine Lease approval, is based upon the applicability of the original characterisation.Tacit to this process is that there is no change in the geochemistry of the tailings, i.e. no change in the implications for acid & metalliferous or saline/neutral mine drainage (AMD/SNMD) generation. But any changes in milling and processing can have a substantive impact on the geochemical behaviour of the tailings metallurgy, and potentially render an operation non-compliant within the conditions of the mine license.Environmental and statutory approval implications for continuous improvements of metallurgy need to be understood because unintended consequences could cost more than the benefits of the improvement, and in some cases cost more than all the profit made from the mine.  Examples uncovered during audit and consultant practice will be presented together with a process to ensure implications for adverse environmental harm and license conditions are fully considered.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Continuous improvement - how changes in metallurgy can have a substantive impact on environmental impact and closure - lessons learnt from environmental auditing, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Scott Ellenbecker

The formation in Newmont Mining?s Phoenix Mine near Battle Mountain, NV contains high levels of abrasive quartzite as well as gold, copper and silver. Newmont started mining operations at Phoenix (formerly Battle Mountain Gold) three years ago and the planners knew they were working with a challenging geological formation. But as it turned out, it was more challenging than anticipated. Mine manager Mark Evatz said, ?Anything that touches Phoenix rock wears fast. The rock fights back here.? To contend with the hard conditions, Newmont uses Atlas Copco?s Pit Viper 271 (PV-271) blasthole drill. Because of the hardness of the rock, drilling at Phoenix requires hammer drilling and the mine uses Atlas Copco TD65 hammers with 171 mm (6.75 in.) bits. The mine?s PV-271?s are outfitted with a single 41 m3/min (1450 cfm), 2.4 MPa (350 psi), oil-flooded air compressor. Phoenix has six Atlas Copco PV-271 drill rigs plus an Atlas Copco DML and a DM45 midrange blasthole rig. The mine?s goal is to keep 3.6 Mt (4 million st) of muck in inventory to stay ahead of the shovels and support needed operational flexibility (ore control related). Drilling efficiency has been a continuous point of improvement since operations began at the mine. The single-pass depth capability of 16.5 m (55 ft) on the PV-271 helped with that. Originally, the plans called for 6-m (20-ft) bench heights, supported by 7-m (23-ft) drill depths, and time spent moving from hole to hole was eating up productivity. Drilling on that plan resulted in drilling an average of 14 m/h (47 ft/hour). When depths were changed to 13-m (44-ft) drill depth, supporting blasting of 12-m (40-ft) benches, they were able to use the single pass capacity of the PV-271. Performance increased to more than 18 m/h (60-ft/hour) an hour. Although the drill depth change largely supported the improvement, other aspects of continuous improvement associated with improved knowledge of the Pit Viper drills helped as well.

Jan 1, 2009

By Tsuchida N

The history of world nickel production has been affected significantly by the supply and demand situation and fluctuation of LME price of nickel metal. In the beginning of the 1980s, the decline of price and demand lead to the withdrawal of un-competitive producers and the shrinkage of the production capacity. During the same period, Sumitomo Metal Mining maintained the production level with continuous improvement of the traditional matte electrorefining process. However, Sumitomo has recognised that the continuous improvement alone does not promise us the ability to catch up with rapid changes in the world. In the meantime, Sumitomo intensively researched chloride hydrometallurgy and has developed the chloride process for the nickel refining. This includes the solvent extraction and chloride electrowinning in the mixed sulphide process and the chlorine leach of the anode slime arising from matte electrorefining. In the late-1980s, Sumitomo Metal Mining decided to develop a new nickel refining technology based on chloride hydrometallurgy. The new process was designed from the comprehensive aspects involving safety and the environment. Construction of the plant for the matte chlorine leach electrowinning (MCLE) process was commenced in 1991. The MCLE plant with a capacity to 2000 tonnes per month has been commissioned at Niihama since 1992. The process has provided high productivity, overall good economics and high quality of electrolytic nickel produced. After the establishment of the process, Sumitomo has maintained continuous improvement of the new process and has attained the best practice of the work classification.

Jan 1, 1996

One of the more recent developments within the mining industry has been the adoption of formal continuous improvement programs. A continuous improvement (CI) program was launched across Kalgoorlie Consolidated Gold Mines (KCGM) in early-2002. The purpose of this program was to identify further operating improvements within departments. The focus of the continuous improvement program was not only on the areas of the operation which were performing below expectations but also on areas of the operation which were performing well but could still be further improved.The effectiveness of a continuous improvement program depends on the stability of the processes in place and the participation of many employees from all levels of the business.Continuous improvement has had some successes and failures at KCGM and this paper will discuss both within the open pits department. Further improvements that could be made to the process will also be discussed. Kalgoorlie Consolidated Gold Mines Fimiston operation is located in the Kalgoorlie Goldfields and it the largest gold mine in Australia producing over 800 000 ounces of gold per annum.

Jan 1, 2004

By Coates J. R, Firth I. C

The Imperial Smelting Furnace at Cockle Creek, NSW, was constructed in 1961 and is the oldest facility using the Imperial Smelting process in operation. In recent years there have been significant improvements in many areas of the operation, including production, safety, hygiene and environmental performance. Steps taken to achieve these improvements are described. Plans to secure a profitable future while meeting environmental requirements are outlined.

Jan 1, 1993

By Jeane Hull

Jan 1, 2009

By Ghassan Skybey

Australian coal mines uses state of the art technology in coal rib reinforcement. This paper highlights the development over the past 15 years in coal rib support technology, along with the advantages and disadvantages of each system. It also outlines the current trend in using coal rib reinforcement in speeding up the dowels installation to improve the current low drivage rate. An innovative cuttable dowel is discussed which improves the drivage rate. This new dowel is self anchoring it uses no resin anchor it has a 5 tonnes (5.51 tons) anchor capacity and can be fully installed in approximately 10 seconds.

Jan 1, 1995

By Markku Rytkonen, Shaolong Chen, Ilpo Kylmäkorpi, Hannu Mansikkaviita

Though the Peirce Smith (P-S) converter is a traditional type of furnace, continuous improvement in its mechanical and electrical design is still Kumera's approach. Efforts are made particularly on the following aspects: converter head shape for easy fabrication and structural strengthening, oxidation air swivel joint for low pressure drop and low noise level, wind box for even air distribution to tuyeres, drive unit and its control for reliable and handy operation. These improvements have successfully been applied in recent P-S converter deliveries.

Jan 1, 2009

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By J. van Huyssteen, M. Cantor

Newmont Ghana Gold Limited's Ahafo Operation has matured from its project ramp up stage into steady state operations after three years of operation. Management focus has shifted from addressing construction and commissioning problems to optimization and improvement. This focus change has coincided with the introduction by Newmont of a Continuous Improvement (CI) program across the company which provided a project management methodology that can be used in the execution of smaller scale projects. This paper focuses on the application of CI principles at the Ahafo Plant through the discussion of several case studies that demonstrate how these principles are applied.

Jan 1, 2011

By M. Mikolás, L. Pomothy, K. Špakovská, M. Vanek

"Enterprises are faced with increasing economic competition and managers are obliged to look for methods that will ensure a competitive edge in their companies’ markets. These methods include managerial concepts that employ common sense and are low cost. One of these approaches is the KAIZEN methodology, of Japanese origin; kaizen means continuous improvement (CI) when translated. A mining company, despite some of its idiosyncrasies, is just an enterprise where the application of KAIZEN can be advantageous. The company investigated, OKD, is the only domestic producer of hard coal in the Czech Republic and operates four mines that produce 11 Mt of coal annually. The OKD management team opted for KAIZEN as their principal method of continuous quality improvement. This paper suggests ideas for development and application of processes that provide for continuing improvement of production and management. The authors have taken the OKD Company to be their benchmark in the field of mining activities. The paper also focuses on possible difficulties accompanying the introduction of CI sustainable methods. Three years of application of CI methods has increased the income of the company by almost US$38.1 million, which provides a strong argument for continued application."

Jan 1, 2015