Search Documents

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016

By Emil B. Milosavljevic, Ljiljana Solujic

Cyanide is exceptionally reactive, and in typical gold/silver processing liquors, cyanide may be transformed into various species and forms depending on the mineralogy of the ore and chemical make-up of the process water. The exact speciation and relative concentrations depend on the Eh and pH values, as well as the free CN concentration in the system. Very good cyanide balances can be achieved by the judicious selection of the analytical techniques used. The choices an analyst has to make (which analytical methods to use and which ones to avoid) in order to gain better understanding of cyanide speciation and balances in a particular system under investigation will be discussed. Examples of cyanide balances obtained for the laboratory scale tests (agitated leach and column tests) will be presented and discussed.

Jan 1, 1999

MODELLING FOR DESIGN AND CONTROL AT KALGOORLIE NICKEL SMELTER Modelling at KNS has been driven by a need to have better tools to answer questions about control, design and optimisation of the plant. This paper describes a number of modelling tools developed for use at KNS and how the development of modelling tools fits with a design and control strategy. In the area of control, a thermodynamic model has been developed to allow process parameters to be calculated. The model allows for the automatic selection of data from a laboratory data base, desired operating set points are input and the operating parameters are calculated. The model has the ability to adjust the burner efficiency and the furnace heat loss depending upon conditions. To assist with the testing of proposed furnace design changes, various mathematical models of the burner and shaft have been created using PHOENICS. These models are particularly well suited to combustion heat transfer and flow aspects of both the burners and shaft. Validation of these models have been based on novel sampling and measuring techniques in the shaft and also by using scale and cold models. Overall plant energy and cost structures can be analysed using a flowsheet simulation, developed to evaluate potential alterations to the plant flowsheet. This model system allows the global evaluation of process changes.

Jan 1, 1993

By R. T. Seaman

Pressure oxidative treatment of whole ores and/or mineral concentrates is used to leach or liberate metals of value for downstream recovery. Silver, when present, is often lost in processing, precipitating as a cyanide-insoluble jarosite in the residue. Depending on pressure oxidation conditions, the degree of silver loss to jarosite can vary dramatically. Batch bench-scale testwork is often performed to define that loss, and then assess the implications in continuous operations. This paper focusses specifically on the impact of CESL pressure oxidation conditions on silver recovery, and discusses limitations of batch bench-scale testing as well as means of overcoming these limitations to better predict silver recovery in the scale up from bench-scale to continuous operations. Since silver is only partially soluble in both sulphate and chloride media, it will gradually leach and deport to a jarosite as oxidation progresses. When a silver-insoluble anion, for example iodide, is dosed prior to oxidation, there is a marked improvement in silver recovery from batchgenerated residue; however, that benefit is not consistently seen in continuous operations. The difference has been attributed to the dynamic solution conditions in the batch test, specifically the first few moments of oxidation. Using these principles, a predictive correlation has been established between initial leach concentrations of iron and acid and ultimate silver recovery with iodide addition.

By Tianming Sun, Gabriella Tranell, Ragnhild E. Aune, Mark William Kennedy

Rare Earth Elements (REEs) are critical for the production of many advanced materials and products. Mining and primary production of REEs are generally associated with significant environmental impacts. By recovery of REEs from secondary sources, through recycling or as a byproduct, the adverse environmental impacts may be partly avoided. In the present study apatite concentrate originating from iron ore beneficiation done by LKAB in Kiruna, Sweden, is explored as a possible source for REEs. The composition and distribution of the REEs within the concentrates are studied using ICP-MS, XRD and SEM-EDS/EPMA, as well as the melting point and heat of fusion using DTA-TGA-MS. The behavior of the material during melting has also been studied through wetting and slag saturation experiments. The overall aim of the study is to evaluate the implications for future smelting experiments aimed at concentration and recovery of the REEs.

Jan 1, 2015

By Larry M. Southwick, Phillip J. Mackey, A. E. (Bert) Wraith, Albert Pelletier

In 1881, the first commercial pneumatic Bessemer-type converter treating copper matte was successfully introduced by Pierre Manhes at the Eguilles copper plant near Vedène in France. This development followed over a year of testing on a smaller scale at a foundry in Vedène, during which the vertical tuyeres of the conventional Bessemer converter had been successfully replaced by horizontal tuyeres in an effort to avoid the freezing of copper which had occurred in the bottom of the vessel having vertical tuyeres. The Manhes Converter, as it became known, was the first successful large-scale adaptation of the Bessemer concept of using compressed air blown into a melt for metal refining and treatment. Within a few years, Manhes Converters utilizing horizontal tuyeres in either the original type of vertical converter, or a later and more enduring horizontal barrel converter, were in operation at over a dozen copper smelters around the world. It was this process that Messrs Peirce and Smith essentially improved with the introduction of the larger converter which bears their name and the development celebrated at this Symposium. The present paper briefly traces the original development by Pierre Manhes in the early 1880s and which set the stage for the later Peirce-Smith adaptation. The paper observes that the original development by Manhes was in part driven by the need to reduce coal (energy) consumption and hence the production cost in order for Eguilles to remain competitive with the larger plants in Swansea, Wales, where a ready supply of cheap coal helped keep smelter treatment terms of the day low. These themes are eerily resonant of today where booming copper production in China has impacted the industry, and also where energy consumption, closely linked to today’s more familiar theme of ‘climate change’ remains an important challenge currently confronting the entire industry. The paper concludes with comments on these seemingly parallel situations today and offers some thoughts for the future.

Jan 1, 2009

By E. Saez, M. Bellet, T. Coupez, O. Jaouen

"The paper presents a 3D finite element solver for non-steady state fluid flow. The thermomechanical simulation package REM3D® has been initially developed to model Stokes' flow for polymer injection. The mechanical module is based on a Eulerian velocitypressure formulation. The spatial discretization uses P 1+IP1 tetrahedral elements. The front tracking module consists of the resolution of a transport equation, thanks to a space-time discontinuous Galerkin formulation. It includes mesh adaptation, which permits a dynamic refinement at the front, thus controling the numerical diffusion. The same approach is used to solve heat transfer. In this paper, we focus on the specific adaptations done to treat Navier Stokes flow. The treatment of inertia is detailed, as well as the implementation of sliding conditions at mould surface, using conservative normals. Industrial applications are presented.IntroductionThe study of the mould filling stage in casting processes requires the ability to simulate complex non steady-state three-dimensional flows. Most commercial software use the volume of fluid (VOF) method, associated with a Eulerian formulation, see for instance the series of conferences ""Modelling of Casting, Welding and Advanced Solidification Processes"" [1-3]. The VOF method [4] consists in solving the conservation equation dF / dt = 0 for a variable F - the volumic fraction of fluid - whose value is 1 in filled regions and 0 elsewhere. Two fluids are actually considered: the molten alloy and a gas in the empty regions. This method suffers generally from numerical diffusion in the resolution of the free surface tracking equation, which is of pure advective type. The precision of the computation is then strongly dependent on the mesh density. Since the mesh is fixed (Eulerian formulation) this implies that in case of complex flow the user must have a priori a fairly good idea of the flow characteristics in order to capture properly the critical features of the flow. In addition, the method can hardly handle the discontinuity of the material viscosity at the interface. To prevent this difficulty, the viscosity value is smoothed around the interfuce, adding once again some inaccuracy. Since the value F = ½ is supposed to represent the free surface, it results in a smeared fluid surface. An alternative to the fixed mesh methods are the methods in which the mesh covers the fluid domain only, as proposed by Navti and Lewis [5-6], or Gaston and Bellet [7]. Based on updated Lagrangian schemes, they must be associated with an ALE formulation (arbitrary LagrangianEulerian) in order to reduce the number of full remeshing operations."

Jan 1, 2004

By Gudrun A. Saevarsdotti

For decades tile aluminium industry has been practicing gas treatment of aluminium melts. This treatment is of great importance because of its influence on 'impurity" and inclusion removal from the melt. The gas-melt interaction is greatly influenced by the gas composition, melt temperature etc. This paper gives an overview of the interaction between argon-chlorine gas mixtures and the aluminium melt. It covers the thermodynamics of the reaction between the chlorine and a number of different elements commonly found in liquid aluminium, and discusses the behaviour of reaction products in the melt. The paper reports an experimental study of the behaviour of the chlorine-molten aluminium interface, using sodium contaminated aluminium melt with and without the addition of grain refiner.

Jan 1, 1996

By Zhengjie Chen, Wenhui Ma, Jijun Wu, Kuixian Wei

The gasification reactivity of PC (petroleum coke), strengthened by addition of different potassium carbonate proportions using different grinding medium, was investigated by using thermogravimetric analysis (TGA). Results showed that the gasification reactivity of PC not only increased with the increase of catalyst-loaded, but also showed the effective improvement by anhydrous alcohol. The PC was mixed with potassium carbonate [K2CO3] catalyst at 0.5%, 0.8%, 1.0% and 1.5%, and then ground wet with distilled water. The CO2-gasification rate of PC was only 77.35%, 80.55%, 84.07% and 85.88% under the gasification temperature 1100 °C and holding time 120 min, at different K2CO3 respectively. However, when the PC was ground in anhydrous alcohol at the same condition of catalyst-loading, the gasification rate of PC reached 95.43%, 96.63%, 95.50% and 95.61% at the holding time of 108 min, 101 min, 74 min and 35 min, respectively. It was shown by FTIR, SEM and EDX determinations that the anhydrous alcohol used as the grinding medium can further improve the gasification reactivity of PC when compared with the distilled water.

Jan 1, 2016

By Ing. R. Geutskens

Zinc-bearing dust from blast furnace gas-scrubbing operation is a well known environmental health problem in the iron and steel industry. Hoogovens IJmuiden (The Netherlands) developed processes to solve this problem. 90% of the zinc is concentrated in 25% of the dust (the fine particle fraction) by means of slurry-hydrocyclonage. The resulting fine particle fraction is treated in a pressure leaching process. Hydrochloric waste pickle liquors have been used as a leaching liquor. By creating optimal leaching conditions more than 98% of the zinc is brought into an acid' solution, whereas nearly all the iron remains in the residue. The zinc can be separated selectively from the solution. The residue can be reused in the blast furnace (via the sintering plant). In the article information is given about the research work and -results of the pressure leaching process as well as the possibilities of the process for solving comparible problems.

Jan 1, 1990

By Xinghui Meng

The leaching behavior of platinum powder in .iodide solutions under oxygen pressure in an autoclave was investigated. Ammonium salts were added to the leaching solution at neutral pH as a key lixiviant for platinum. The effect of temperature, partial pressure of oxygen, concentration of iodide and of arttmonium salts on the dissolution rate of platinum was examined. Under experimental conditions, the leaching behavior of platinum powder exhibited a complex reaction mechanism. A precipitate was found during the leaching process and was identified to be platinum ammine iodide, Pt(NH3hI4. The dissolution rate was controlled by a series of chemical reactions, the equilibrium concentration of the platinum ammine iodide being responsible for the ultimate limit to the recovery.

Jan 1, 1996

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. This project is concerned with the determination of the effects of operating variables on the reaction of the particles. Experiments were carried out in a large laboratory-scale flash furnace with 72 wt-% Cu matte by varying initial particle size, temperature, oxygen partial pressure, oxygen-to-matte mass ratio and residence time. Chemical analysis was used to study the oxidation extent and copper volatilization. Particle fragmentation was examined. Fractional conversion and sulfur removal slightly decreased with initial particle size, while a higher oxygen-to-matte mass ratio mainly resulted in higher fractional conversion and more efficient sulfur removal. The fractional conversion values represented the overall extent of oxidation more closely than degree of sulfur removal.

Jan 1, 1997

By Philip Arthur

The ISASMELT process is making a significant contribution to the global metals industry. ISASMELT furnaces are now operating successfully in eight different countries and treating approximately 3 million tonnes of concentrates and secondary materials per year. The process is currently used in both lead and copper smelting. The most recently commissioned plants were in Germany and China, one for treating scrap copper and the other treating low-grade copper concentrates. The Copper ISASMEL T furnace ("CIF") at Mount Isa Mines Limited (UMIM") has continued to set new operational records, with throughput of more than I million tonnes of concentrate per year and very low operating costs. This paper summarises the latest operational data from the Mount Isa Copper ISASMEL T plant and outlines the successful approach to industrial R&D taken by MIM in the development of the ISASMEL T process.

Jan 1, 2003

By Wei Luo, Yuanbo Zhang, Zhixiong You, Zijian Su, Guanghui Li, Tao Jiang

"In this study, the appropriate sintering process parameters for low-grade ferromanganese ores were investigated. The results showed that, under the condition of natural basicity (R=0.03), the optimal parameters were obtained as follows: moisture of mixture 9 .1 %, coke powder 9 .9% and sintering negative pressure 7 KPa. And the corresponding yield, ISO tumbling index and utilization coefficient reached at 80.18%, 61.27% and 1.515t·m-2·h-1, respectively. Under the optimal parameters, the emission of harmful gases, such as S02 and NOx, were reduced evidently with 30% of coke powder replaced by biomass charcoal. Moreover, it was found that the basicity had obvious effects on the quality of the sinters when it changed between 0.03 and 2.4. The ISO tumbling index gradually decreased from 61.27% to 55.47% with the basicity increasing from 0.03 to 1.2, then, it began to increase after the basicity further increased to 2.4.IntroductionManganese is mainly consumed by steel and battery industries, particularly in the steel plants and ferroalloy units. The consumption of metal manganese in the ferroalloy industry accounts for 85%-90% of the total Mn [1-2]. Therefore, ensuring sufficient manganese alloys is essential to meet the rapid development of steel industry. Recently, rich-manganese slag containing high grade Mn (>40%), low Fe (1%) and P (<0.03%) is considered as superior raw materials for manganese alloys. While the sinters made from manganese ores are major raw materials for producing rich-manganese slag with the increasing exhaustion of natural rich manganese lump ores [3-5]."

Jan 1, 2013

By D. M. Jones

Dust generation data have been obtained from 19 industrial Outokumpu flash furnaces. Statistical analyses of the data have been carried out and the most significant factors affecting dust generation evaluated. The results indicate that dust production may most effectively be minimized by: 1) Minimizing the distance between the molten slag and the furnace roof 2) Optimizing burner design and combustion parameters.

Jan 1, 1996

By Yuzhe Zhang, Matthew Andriese, Jiann-Yang Hwang, Guanghui Li, Zhiwei Peng, Tao Jiang

The microwave power absorption characteristics of iron oxides, including Fe2O3, Fe3O4 and Fe0.925O, have been studied by determining dielectric loss and magnetic loss distributions in 0.05-m-thick oxide slabs irradiated with 1.2-kW, 2.45-GHz microwaves. The results reveal that the dielectric loss is the main factor contributing to microwave absorption in Fe2O3 and Fe0.925O, while the magnetic loss dominates the power absorption in Fe3O4 below its Curie point. Uneven power distributions are observed in the slabs and this phenomenon becomes even worse at high temperatures at which the permittivity increases significantly. Quantification of power absorption in the oxides is of great importance for efficient and uniform microwave heating

Jan 1, 2015

By Onuralp Yucel, Ahmet Turan, Murat Alkan, Hasan Ozer

SHS (Self-propagating High-temperature Synthesis) is one of the important methods to synthesize B4C powders. The process contains the reaction of boron oxide powders (B2O3) with magnesium reducing agent and carbon black carburizer. SHS products are leached in HCl media to purify synthesized B4C powders in the following step. In the present study, effects of various functional additives (KClO3, KHSO4, MgSO4.7H2O, NaCl, MgO and Na2SO4) in the SHS stage were carried out. Various proportions of the additives were mixed with the initial SHS charge mixtures. Two different molar ratios were employed in the initial SHS mixtures as 1:3:0.8 B2O3:Mg:C and 1:2.5:0.8 B2O3:Mg:C. After the SHS step, HCl leaching process was applied to the SHS products. Filter cakes were dried and characterized by using X-Ray Diffraction Spectroscopy, BET and chemical analysis techniques.

Jan 1, 2015

By Richard J. Abitz

Thennodynamic geochemical models have been applied to assess the relative effectiveness of a variety of reagents added to aqueous waste streams for the removal of radioactive elements. Two aqueous waste streams were examined: effluent derived from the processing of uranium ore and irradiated uranium fuel rods. Simulations of the treatment train were performed to estimate the mass of reagents needed per kilogram of solution, identify pH regions corresponding to solubility minimums, and predict the identity and quantity of precipitated solids. Results generated by the simulations include figures that chart the chemical evolution of the waste stream as reagents are added and summary tables that list mass balances for all reagents and radioactive elements of concern. Model results were used to set initial reagent levels for the treatment trains, minimizing the number of bench-scale tests required to bring the treatment train up to full-scale operation. Additionally, presentation of modeling results at public meetings helps to establish good faith between the federal government, industry, concerned citizens, and media groups.

Jan 1, 1996

By Jagdish C. Agarwal

Although copper ranks very low in the order of abundance of elements in the crust of the earth, it has been one of the first metals utilized by mar, at his emergence from the Stone Age, about 10,000 years ago. Use of copper for weapons, tools, utensils and ornaments dates back to the twilight of history, 6,000-5,000 B.C. Native copper outcrops and the malleability of the metal explain its very early use by the cave-dwellers. The working, melting and extraction of copper from its minerals are among the oldest metallurgical achievements of the human race. The oldest complete smelting installations for the extraction of copper from its minerals, dated about the fourth millenium B.C., were recently discovered in the Timna Valley, Wadi Arabah, Israel. (1) The history of the developments of the extractive metallurgy of copper has been adequately reviewed recently. (2,3) The center of copper production migrated from the Eastern Mediterranean to Northern Europe (Mansfeld, Germany, Swansea, Wales) towards the end of the Middle Ages (1500 A.D.). The production of the metal was boosted tremendously in North America since the end of the nineteenth century (Fig. 1).

Jan 1, 1976

By Simon Lekakh, Von Richards, C. Hank Rawlins, Kent Peaslee

"Batch aqueous leaching and carbonation tests were conducted using industrial steelmaking slags to determine the effect of carbonic anhydrase enzyme as a catalyst. Calcium leaching is a strong function of particle surface area, and the extent can be expressed as a function of time and particle size. Carbonic anhydrase did not affect the calcium-leaching rate, however, it did catalyze calcium carbonate formation to achieve a neutralization time near the theoretical rate. Additionally, carbonic anhydrase modified the precipitate morphology due to accelerated particle nucleation. Time controlled tests in which the pH dropped to ~6 decreased the amount of carbonate produced, and this effect was exaggerated by carbonic anhydrase, while pH controlled tests (>8.5) exhibited the highest rate of carbonation. Because the leaching rate was ~50% faster than the carbonation rate, a further increase in the amount of carbonation may be realized by using carbonic anhydrase however pH must be >10.3.IntroductionSteelmaking slag contains high fractions of alkaline earth oxide based phases (i.e., CaO and MgO) that exothermically form carbonates. Thus, it is being considered as a means of permanent carbon dioxide sequestration. At current U.S. steel production rates, approximately 13-17 million tons/year of slag are generated from basic oxygen furnace (BOF), electric arc furnace (EAF), and ladle metallurgy furnace (LMF) processes [1]. BOF and EAF slag is used as high quality mineral aggregate or cement clinker, while LMF slag, produced at ~15% the rate of BOF and EAF slags, has limited use as blast furnace flux or acid mine neutralization with the majority going to landfill [2]. Based on slag’s chemical nature and immediate availability as a co-product from steel production, the steel industry initiated a project to investigate hydrous carbonate formation in steelmaking slag as a method of sequestering carbon dioxide emitted in steelmaking offgas [3]. The goal of this project is to determine the reactor parameters suitable for the design of an industrial system for treating steelmaking offgas with raw or minimally processed slag."

Jan 1, 2009