Search Documents

By Dongok Kim

Regardless of the advantages of the Friction Stir Process (FSP), for age-hardened aluminum alloys, the mechanical properties such as hardness in the stir zone decreased after FSP due to the growth or dissolution of strengthening precipitates. Here, as a new technique, FSP was introduced to alloy copper nanopowders in Al7075 T651. Mechanical properties of copper nanopowder- alloyed Al7075 T651 together with micro and nanostructures were compared with those of as-FSPed Al7075 T651 using SEM, TEM, and Vickers hardness testing to understand structure-property relationships. It was observed that Vickers hardness of the stir zone in copper nanopowder alloyed Al7075 T651 increased by 20% compared to that of the heat affected zone, while the as-FSPed samples did not show a noticeable increase in hardness in the same zone. Xray mapping showed traces of copper nanopowder after the process. TEM is being used to verify if there was CuAl2 formed in the copper alloyed sample.

Jan 1, 2006

By Murat Baydogan

Effect of retrogression and reaging treatment on hardness and stress corrosion cracking resistance of 7075 aluminum alloy was investigated. As received 7075 alloys in T6 temper condition were retrogressed at 170, 220, 240 and 380°C for different durations between 15 s and 60 min. Subsequent reaging was made at the T6 aging condition. Treated materials exhibited higher hardness and better stress corrosion cracking resistance than T6 temper in a wide range of retrogression temperature and time. The highest hardness was obtained after retrogression at 170°C for 210 s followed by reaging, corresponding to 20% hardness improvement. Improvement in stress corrosion cracking resistance of the alloy by as much as 85% was also observed. In this paper, improvements in hardness and stress corrosion cracking resistance are discussed on the basis of the microstructural changes during retrogression and reaging treatment.

Jan 1, 2006

By Changqing Su

A batch incubation experiment has been carried out to investigate the optimal condition for the microbial remediation of hexavalent chromium (Cr(VI)) in soils contaminated by chromate ore processing residue at Hunan Iron-Alloy Factory in China. The optimal condition was obtained by comparing the remediation efficiency of Cr (VI) by indigenous bacteria under different culture media, the quantity of nutrient sources, the pH and the temperature. The results indicated that glucose and yeast extract was the optimal component of culture medium and the quantities of the above components were 8 g L-1 and 13 g L-1, respectively. The optimal temperature and pH value were 30_ and 10.0, respectively. A bioreactor was operated under the optimal condition to evaluate the efficiency of Cr(VI) remediation in the contaminated soil. The result showed that water soluble Cr(VI) in soils was reduced from 320 mg kg-1 Cr(VI) of the initial concentration to below detection limit after 30 h in a bioreactor. Thus, there is a large potential to make bioremediation for the reduction of Cr(VI) to Cr(III) by the addition of optimal culture medium under aerobic condition.

Jan 1, 2010

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By Li Chen

A new process, i.e. Ball milling--Neural leaching--Oxidation calcinations--Chloridizing distillation--Hydrolysis, was designed to recover germanium from the vacuum furnace slag produced in Shaoguan smelter. The suitable process and operational parameters were determined for the practical production.

Jan 1, 2005

By Jinhui Li

Silver is a very important metal used in a wide range of applications. It is necessary to recovery of Ag from electronic wastes for increasing of Ag price and circumstance protection. For separating and recycling Ag from Ag-Cu composite materials, thermodynamic data of reaction is calculated and some experiments have been proceeded with Ag-Cu composite material scraps, time, temperature, nitric-sulfuric mixed acid volume ratio and the volume ration of mixed acid vs. water have been discussed. The results show that the optimization conditions is that nitric-sulfuric mixed acid volume ratio 5:95, volume ratio of mixed acid vs. water 10:1, temperature 55?, time 25min. In the conditions, Ag can be selectively leached from Cu-based composite material, Cu base is not eroded nearly.

Jan 1, 2009

By Hui Wang

With the great increasing use of nickel metal hydride batteries recently, the waste of this kind batteries have been paid for close consideration. For the main reason that the waste of the batteries contained precious metals and lanthanide which cost great lose. This paper introduces the pyrometallurgical process of recovering nickel and cobalt from the waste of the nickel metal hydride batteries. Particularly, the waste for the process was from factory during the producing program. The use of designed solvent to divide nickel and cobalt in melted state from the waste is described. Also, the result of the nickel and cobalt and melted gangue that mainly consist of lanthanide oxide are included in details. The aim of the paper is to find out a simple and feasible way to reuse waste from nickel metal hydride batteries.

Jan 1, 2009

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By Chang Chia -Fu

The generic structure of our bimesogens is shown in and for a typical blue-phase mixture of the type we describe here. We use mixtures of the ratio 33.4% (n =2.6), 34.1% (n =6.57), 36.6% (n= 11.15) with of the high twisted power (HTP) agent BD H1381(available from Merck Chemicals and described in ref. We then studied the electric-field dependency of the selective reflection in BP I* at 20.7 °C by applying increasing and the decreasing pulsed alternating current (a.c.) electric fields (100 Hz).

Jan 1, 2006

By Taegong Ryu

Nanosized tungsten powder was synthesized by the hydrogen reduction of ammonium paratungstate (APT) in thermal plasma. The effects of operating conditions on the product composition and particle size were investigated. The particle size of synthesized W powder was less than 30 nm in all cases tested. The sintering behavior of the synthesized powder (25 nm average size) was then investigated and compared with those of commercial W powder of 500 nm average size and W powder of 23 nm average size produced by milling the commercial powder. The sintering was done at 1400oC with various holding times. The hardness of the resulting compact from the synthesized W powder (315 VHN) was similar to that from the milled W powder (309 VHN), but the plasma-synthesized powder had a much lower tendency to form cracks. The compacts of both nanopowders were significantly harder than that of the commercial powder (192 VHN).

Jan 1, 2009

By C. E. M. Meskers

Electronic and Electric Equipment contains a range of components made of a wide variation of metals, plastics and other substances. Up to 60 elements can be found in complex electronic equipment: base metals, precious metals and special metals in circuit boards and batteries. Because of its amount WEEE represents a considerable metal resource with a higher special and precious metal content than found in ores. The Umicore integrated smelter and refinery recovers and supplies back to the market 17 different metals from EEE. Pre-treated materials enter state of the art, material and energy efficient metallurgical processes for environmentally sound recovery of metals and treatment of off gasses and hazardous substances. The organics in the feed function as reducing agent and alternative energy source during smelting for precious metal recovery. Lithium-ion batteries are treated using a dedicated process. As a result the environmental footprint of metals produced from EEE is much smaller than primary production.

Jan 1, 2009

By Jacques J. Eksteen

Any effort to improve the metallurgical control of industrial furnaces employed in the primary extraction of high carbon ferroalloys are bound to fail unless the variability of the melt is not fully accounted for. A number of sampling campaigns were performed on both 3phase AC submerged arc and single phase DC open arc furnaces at different smelter sites in South Africa where High Carbon Ferrochrome is produced. It was found that the heterogeneity between multiple samples during a single taps were much higher that for heterogeneity found within a sample. Moreover, this heterogeneity (as quantified by the relative standard deviation per tap) varied with the operating conditions of the furnace, the element monitored and the type of furnace. A relationship was found between the relative standard deviation of certain elements and the degree of subcooling of the melt.

Jan 1, 2006

By Jiann-Yang Hwang

Microwave heating has been proved an effective method to rapidly heat iron oxide. This offers an opportunity to apply microwave heating in the steelmaking process. The reduction reaction of iron oxide is traditionally achieved at high temperature with reducing gases such as H2 and CO generated from various sources, including coke, coal, and natural gas. This study investigates the differences in iron oxide reduction using conventional and microwave heating under H2 and CO atmospheres. A special microwave thermal gravimetric device was designed and built to facilitate the investigation. With this device, iron oxides can be heated by electric resistance heating, microwave heating, or a combination of methods. The incoming CO and/or H2 also can be preheated to simulate a potential utilization of recovered heat. The iron oxide weight and temperature can be monitored during an entire reduction period. A series of reduction experiments have been conducted. The results are presented and discussed.

Jan 1, 2006

By Preston C. Holloway

Transformational roasting involves the heating of a material along with specific additives to induce mineralogical changes in the starting material. By controlling the chemical composition, roasting atmosphere, temperature and time of reaction, the mineral transformations induced during roasting can be engineered to control the distribution of valuable, or harmful, metals and to produce new mineral assemblages that are more amenable to conventional methods of metals recovery or to environmentally safe disposal. To date, this type of process has only been applied to the recovery of a limited number of metals, but current research is looking to expand the application of these techniques to the recovery of metals from a wider range of materials. An introduction to these techniques is presented along with preliminary results from their application to metals recovery from zinc bearing wastes, such as zinc ferrite leach residues and carbon steel electric arc furnace dust.

Jan 1, 2006

By M. T. Baquera

A comparison of microstructures associated with W single-crystal ([001], [011], [111]) rods prior to deformation (as grown), and after quasi-static compression (at a strain rate of ~1/s) by transmission electron microscopy (TEM) shows several orders of magnitude difference in dislocation density. Dislocation substructures were not significantly different amongst the deformed sample orientations. In contrast, [001] W rods penetrated into steel targets, at impact velocities of ~1.3 km/s, exhibited heavy dislocation densities and dynamic recrystallization as very distinct microstructural regimes accommodating the penetration process. Twinning on {112} also occurred as a precursor to, or remnant of, these microstructures near the projectile head. These results suggest that deformation accommodating the extreme strains and strain rates associated with the penetration of a single-crystal rod into a metal target is not adequately represented by conventional deformation

Jan 1, 2006

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010