Search Documents

By P. J. Moor

Britannia Refined Metals Ltd. was built in 1931 to refine the lead bullion produced at the Mt. Isa mine in Queensland, Australia. Several periods of expansion and development have taken place over the intervening years, leading to major increases in the refining capacity for both lead and silver. A plant for treating recycled lead-acid batteries was added in 1976. This was redeveloped in the early 1990's to utilise Isasmelt technology for the smelting operations. Most recently the No. 2 refinery kettle floor was extended to enable it to process lead bullion produced from two Imperial Smelting Furnaces (ISF), at Britannia Zinc Ltd. in Avonmouth, England and at MIM Hüttenwerke in Duisburg, Germany. This expansion included the provision of a plant for the hygienic handling of drosses and skims. This paper briefly describes the present primary refining operations and gives an update on the most recent developments in the process metallurgy and operating practices that have taken place.

Jan 1, 2000

By A. V. Tarasov

Emission of sulfur-containing gases causes most adverse impact on the natural environment in the process of nonferrous metals production. Under the conditions of Arctic regions, in particular in the region of the Norilsk Mining and Metallurgical Complex (Russia), this problem requires a special approach taking into account potential economic and socioeconomic consequences. By reducing the iron sulfide content of flotation concentrates by using new flotation reagents inhibiting pyrrhotite flotation and by applying advanced process flowsheets for flotation it is possible to increase the nonferrous metals content of flotation concentrates by 5% or more along with a corresponding reduction in SO2 formation during their subsequent pyrometallurgical processing. The ways used to resolve the environmental problems in the Norilsk region in the process of nickel and copper production, are based on the improvement of methods for elemental sulfur recovery from metallurgical off-gas by non-conventional techniques, the sulfur recovery from metallurgical gases by production of liquid sulfur dioxide and the technology for pyrometallurgical treatment of sulfide concentrates without SO2 formation. Another opportunity is the development and commercial introduction of hydrometallurgical technologies for treating copper-nickel sulfide ores.

Jan 1, 2006

By Frédéric Pineau, Guillaume D'Amours

Semisolid metal processing of metallic alloys takes advantage of the thixotropic behavior of material with non-dendritic microstructure to produce near-net-shape components with improved mechanical properties. The much higher apparent viscosity of the semisolid billet limits the risk of oxide formed on the free surfaces to become incorporated into the easting during the process. But, the external-skin on the periphery of the billet, which is often partially solidified and contaminated with lubricants, should not be included into the casting as this can be a cause of reject for most structural parts. In this paper, a preliminary model is set-up using the LS-DYNA SPH formulation to follow the paths of the skin. Calculations carried out show that this approach appears to be very promising to predict the paths of contaminated skins into semisolid castings. It can then be utilized to design suitable molds and gating systems.

Jan 1, 2012

By Xiaorong Liu

Interfacial emulsion generated in copper solvent extraction is an inhomogeneous O/W emulsion that consists of organic phase, aqueous phase and solid particles. In order to determine what kind of components in organic phase promotes the emulsion, the organic phase separated from the interfacial crud provided by Dexing Copper Mine in Jiangxi, China was analyzed for its components by combined gas chromatography-mass spectroscopy. It was found that many kinds of emphiphiles containing such hydrophilic groups as carbonyl, carboxyl, or acylamine existed in organic phase, most of which were originated from the reagent degradation. Conclusively, Lix984N would degrade gradually during a long-term contact with the acidic aqueous feed and strip reagents. Lix84 and nonylphenol, as effective components of Lix984N, degraded almost completely after long-term recycling. As a result, the effective components of Lix984N were far lower in concentration than the dense-aromatic impurities derived from the diluent and the degradation products in total. The degradation of Lix984N would deteriorate solvent extraction, disengagement performance and result in more serious interfacial emulsion.

Jan 1, 2006

By Mark W. Sajewycz

Creating technology, securing patent rights, and managing a patent portfolio are time-sensitive and dynamic activities. Agreements should be in place with technology partners (employees, contractors, joint venture partners), prior to embarking on research and development projects, so as to mitigate future disputes over patent rights. Technology partners should be educated on patent law basics so as to be mindful of patent bar triggering events. Accurate records must be maintained to capture information relevant for preparation and filing of patent application, including subject matter, names of inventors, and invention date. Developed inventions should be evaluated for whether to file for patent protection, delay patenting until technology is further developed, maintain trade secrecy, or effect deliberate public disclosure. Once decision is made to file for patent protection, time is of the essence, and application for patent protection should be filed as soon as possible, as many countries award patents on a "first-to file" basis. Decisions on where to file are made having regard to potential competitive advantages versus cost considerations, and can be delayed by taking advantage of priority rights recognized in patent legislation of most countries. Once patents are granted, competitors must be policed for potential patent infringement, and legal action may be necessary to prevent patent infringement.

Jan 1, 2006

By Dan Adams

A number of gas-liquid processes require high intensity agitation systems to provide uniform blending and dispersion of reactants in order to achieve desired end products. Processes such as hydrogenation, fermentation, and minerals processing have used conventional down pumping or radial agitation systems with some success. In 1996, LIGHTNIN introduced the concept of Up-Pumping to the industrial marketplace as an improved mixing technology for these applications. For processes requiring gas-liquid mass transfer, such as those listed above, conventional mixing technology requires the use of gas introduction devices (sparges) below impellers. These devices can be a maintenance concern due to plugging and erosion in the presence of solids. Up-Pumping impeller systems are able to draw in a significant amount of gas from the headspace, much more so than conventional vortexing impellers designed for headspace gas incorporation. This paper will demonstrate the effectiveness of Up-Pumping impeller systems that have the potential to eliminate need for sparge devices entirely. It demonstrates the ability of Up-Pumpers to re-entrain gas for higher utilization compared with conventional impeller technology. This is significant in applications using costly gases such as enriched oxygen or hydrogen, reducing overall operating costs of production.

Jan 1, 2003

By Renaud Metz

The DOPA process (Direct Oxidation of a Precursor Alloy) was used to prepare ceramic powders based on doped SnO2 and ZnO. The DOPA process consists essentially in the direct oxidation of a homogeneous precursor alloy. A unique advantage of this process is its rather benign environmental impact since no dangerous reactants are used and no harmful by-products are generated. Only oxygen and the alloy metals participate on the chemical reaction to produce the multi-component oxide. Homogeneous alloys of niobium, cobalt and chromium doped tin have been prepared. The molten metal alloy is atomised in air using a double fluid nozzle to produce metallic powders. A subsequent thermal treatment is carried out to fully oxidise the sprayed metal alloy powders. These raw powders are used to prepare a ceramic powder through a mill homogenisation and atomisation process. The ceramic powder is then uniaxially compacted in disc shape and sintered in an oxidising atmosphere. The resulting sintered bodies are metallised on their flat faces and the cylindrical surface is passivated using lead free glass enamel. These ceramics present excellent semiconducting properties with non-linear (non-ohmic) characteristics. The DOPA process is found to be an attractive procedure to obtain ceramic powders for the preparation of SnO2 varistors.

Jan 1, 2006

By Neil Smith

Mineral processing plants typically procure a range of industrial services from contractors. Their satisfaction and value received is directly affected by how the services are procured, rationalized and delivered. Conventional purchasing strategies often focus on price rather than on optimizing the service relationship between supplier and customer. The nature of this relationship may have the greatest potential to reduce costs and enhance production. It has been documented that a service involves simultaneous production and consumption. A high degree of customer involvement is often necessary for a successful outcome and the expectations and attitudes of the customer can positively or negatively affect delivery of the service. This indicates that the customer can enhance or diminish their own satisfaction and value received and the supplier cannot act alone for best results. The Optimax? Program for industrial services is a service delivery framework whereby a customer and supplier work together to raise the efficiency of the service exchange. The Optimax? Program is intended to help the customer optimize costs and maximize production by connecting the customer and supplier through shared information and objectives. This paper will review the basic nature of services, provide a couple of examples of conventional procurement strategies for services and outline the features of the Optimax? Program. A Case Study showing recent results from implementing the Optimax? Program will be included.

Jan 1, 2006

By V. M. Paretsky

Most recent developments made in the Gintsvetmet Institute in the field of technologies and equipment for single-stage autogenous smelting of copper sulfide raw materials to produce white metal and blister copper on the basis of oxygen-flame smelting process and separation of highly basic calcium-containing slags have been discussed. This technology includes the oxygen-flame smelting process (KFP Process) to produce highly basic self-disintegrating ferrite-calcium slags with their subsequent flotation to recover copper and a basically new sparging smelting process (FBP Process) to produce combined slags subjected to decopperizing inside the same furnace. Results of special investigations of the slag structure obtained in the KFP and FBP processes and substantiating selection of their chemical and phase composition have been presented. It has been demonstrated that the above processes meet the stringent world-level requirements to advanced technologies with respect to energy conservation and environmental safety with different scales of production and within a wide range of specific conditions of particular operations.

Jan 1, 2006

By José García-Antón, Valentín Pérez-Herranz, José Luís Guiñón, Henry Reyes

"The majority of chromium electroplating operations employ Cr(VI)-based baths. During these processes, Cr(VI) is reduced to Cr(III). Besides Cr(III) other undesirable impurities are present such as iron, copper and nickel. The build-up of the impurities limits the lifetime of the plating solutions. Since the disposal of spent chromic acid baths is expensive and can cause significant environmental degradation, there is increasing interest in finding ways to regenerate waste chromium liquors.In this work, an electrolytic cell separated by microporous ceramic diaphragms was used to regenerate chromium plating solutions. The effect of the ceramic diaphragm structure parameters, such as porosity and pore size, on the performance indicators of the electrochemical reactor (fractional conversion, current efficiency, product yield, specific energy consumption) was investigated.The fractional conversion, the product yield and the current efficiency increased and the specific energy consumption decreased with the decrease in porosity.IntroductionChromic acid is widely used in industrial applications such as steel manufacture, metal finishing industries, aluminium anodising, pasivation of cadmium, magnesium, and zinc, etching of plastics and another industrial operations related with processing ferrous and no ferrous metals [1]. These processes employ baths with high concentrations in chromic acid, about 180 and 350 g/L, where hexavalent chromium is reduced to Cr(III):"

Jan 1, 2008

By K. Rajani Kanth

Environmental problem is the major concern for any industry and there is a great need to that along green lines. Sangam Dairy being one of the most famous and wide spread Dairies in India, produces wide spectrum of milk products. The BOD levels of effluent water of this industry with MIF treatment were found to be around 100 ppm. Lot of research has been expended in the past to bring down the BOD levels to bare minimum. The main objective of the present study is to minimize the BOD level to the required level stipulated by environmental standards by employing various seeding materials. For this purpose microbes like Bacillus Subtiles, Pseudomonas, Aspergillas, Staphylococcus, and Pencilium have been employed and BOD levels were analyzed. Various Reagents, solutions with different dilution levels have been successfully prepared. Initial and final Dissolved Oxygen levels were determined before and after incubation. From the DO data, BOD was evaluated for all samples and comparison analysis of various seeding material was carried to suggest the efficient seeding material for the ETP plant. In the process, solutions of different dilutions have been prepared using difficult reagents. These samples are treated with above mentioned microbes and BOD levels are estimated. It has been observed that staphylococcus and Pseudomonas proved to be the best seeding materials. When there microbes have employed BOD levels fall to less than 10 and 20 ppm respectively

Jan 1, 2006

By Fumiatsu Sato

In recent years, an increasing number of urban soil contamination cases have been found during redevelopment of former factory sites. Hydroclassification technique, separating heavily contaminated fine soil particles from contaminated sites, is one of the economical remediation techniques for contaminated soil by heavy metals, but the separated fine soil particles are generally landfilled because of the difficulty in removing strongly adsorbed heavy metals on them. In the previous study, the authors have investigated the mechanism and the optimum condition of chlorination-volatilization technique to eliminate heavy metals from inorganic waste and found it was needed to heat up around 1273K. In this paper, a new remediation technique for lead contaminated fine soil particles is proposed. This technique is composed of chlorination and subsequent warm water extraction. In the chlorination step, water-insoluble lead complex is chlorinated to be water-soluble lead chloride without volatilization, by heating the soils with MgCl2-CaCl2-KCl salt mixture at relatively low temperature. By subsequent warm water extraction, lead chloride is leached out. Effects of chlorination conditions, such as time, temperature, composition of the salt and added salt ratio, on lead behavior were investigated. It was proved that lead concentration could be reduced below Japanese environmental standard.

Jan 1, 2006

By V. A. Bryukvin

It has been found that by superimposing symmetric alternating current over the process, the rate of nickel and cobalt leaching from metallized products with copper sulfate solutions increases by a factor of 1.5 to 2.0 and the apparent activation energy of the process investigated is reduced from 12 down to 6.6 kcal/mole. It appears especially attractive to use alternating current for anodic dissolution (oxidation) of metallic scrap of refractory metals and their alloys in ammonia electrolytes permits production of high-grade commercial products in the form of respective ammonium salts using a short and virtually reagent-free process flowsheet. Similar approaches can be applied also for electrochemical processing of nickel and copper scrap in sulfuric acid media with subsequent recovery of pure sulfate salts or electrolytic processing. Electrochemical technology for recycling of tungsten-cobalt (WC 15) and tungsten-rhenium (WR 20) alloys has been also investigated. In the former case, anodic oxidation of carbide alloy was carried out in nitric acid electrolyte with production of pure tungstic acid. The research conducted has indicated that the physicochemical effect of alternating current results in a lower activation energy of electrode reactions due to changes in the mechanisms of the electrode reactions themselves.

Jan 1, 2006

By Yanxia Lu

Porous silicon carbide (SiC) has been the top selection for diesel particular filters (DPFs) since 2000 because of its high thermal diffusivity and strong body, which help it to survive in the harsh environment of a diesel exhaust system. However, the process to produce SiC DPFs is a costly one. The work presented herein describes more cost effective composite materials for this application, namely Si-SiC and Si₃N₄-SiC. Both composites have shown excellent filtration efficiency, low back pressure and outstanding survivability of regeneration at high soot loadings. Since the composites are batched from silicon metal, they can be prepared by a low temperature process that is impossible in the production of pure SiC PDFs. In fact, fabrication of SiC composites simply involves reactions between nitrogen gas and silicon metal, or silicon metal bonded with SiC, and as such uses a much less costly process when compared to the one employed to make SiC. In addition, the pore structure of the composites can easily be tuned by selecting raw materials and changing the ratio of two components. A typical pore structure consists of well connected pores with a median pore size of 5-20 µm and a porosity of 40-55%. This talk will describe the exothermic behavior as well as the mechanical and thermal properties of SiC composites in comparison to those of SiC filters. It will also show the superior thermal shock resistance of Si₃N₄ bonded SiC which is due to the unique combination of these phases that lowers the thermal expansion and elastic modulus relative to pure SiC.

Jan 1, 2006

By Boris Arlyuk

The system of short term forecast of metal prices at LME is based on correlation between prices within the quarter forward and at the first place by economic parameters at the West, determining the consumption of metals. Such economic parameters are presented by data of indexes of Western World industrial production (WW IP), official data of IP and Dow Jones indexes at USA. For price forecast within the quarter forward (one day ahead, 3 day -65 days MA forward prices) are significant the changes of actual prices (official and close) at the past and the parameters of daily trade at LME at the past (futures turnover, open interest, LME stocks). It is developed subsystem of price forecast within the quarter forward based on analytical approach determining the relations between the participants of the market. It gives the opportunity to reduce the number of empirical coefficients at the model and receive good accuracy of forecast the MA prices and its direction at the future. Very important part of short term forecast is subsystem determining analytically the probability that the price forecasted for the next trading day will be the maximum or minimum daily price within the quarter forward. The thresholds probabilities are defined by identification the model at the past by maximal commercial efficiency. Such system was tested at the past at period since 2000 till 2005 and gives very high commercial results at operations on 1M forwards and hedging the sales of nonferrous metals traded at LME (primary aluminium, light alloys, nickel, copper, zinc, lead and tin).

Jan 1, 2006

By Bohumír Cech, Jirí Hanika, Václav Veselý

"PET bottles are separated and subsequently crushed into flakes. Except for PET, these flakes contain PE, PVC, paper, adhesives, beverages remainders and mineral impurities. PET itself usually is a glycol and terephthalic and isophthalic acid polymer.The suggested method consists in PET flakes crystallization at 255°C. In the meantime, volatile substances evaporate and PVC disintegrates. Formed crystalline PET is crushed into small particles and then is subject to the basic hydrolysis at an atmospheric pressure. In addition to lye solution, glycol is added in the hydrolysis. Water is eliminated by boiling, which gives rise to suspension of sodium salt of terephthalic acid and glycol. The suspension is skimmed and the filtered glycol is vacuum distilled. Pure glycol is then the distillation product.Crystals are dissolved in water and the solution is filtered, which eliminates PE and impurities. Electrodialysis removes pure terephthalic acid salt from the solution. Glycol solution is returned to the hydrolysis. Terephthalic acid is precipitated by a mineral acid. Subsequently, it is washed and dried. The filtrate is separated through electrodialysis to lye and acid. The lye gets back to the hydrolysis and the acid is used for precipitation. Terephthalic acid and glycol are products in a “polymer grade” quality. The waste is a part of washing waters, distillation residues after glycol regeneration and a filter cake after the terephthalate solution filtration."

Jan 1, 2008

By David Forrest

In 1981, K. E. Drexler proposed using massively parallel nanomechanical systems to manufacture large atomically exact structures. As in macroscopic mechanical systems, they would contain components that serve traditional functions such as trusses for support, gears to transmit power, bearings for low-friction support of rotating surfaces, motors to supply torque, pipes and conveyor belts for material transport, and channels for coolant. Many of these components would only contain a few thousand atoms. Specific designs for these devices became available in the early 1990s, and a few working devices appeared in laboratories by the early 2000s. As advances continue, a thorough understanding of the operative transport phenomena will guide the intelligent design and construction of nanomechanical structures, devices, and systems. The familiar equations of continuum mechanics are generally inadequate to describe the flow of heat and mass in the proposed nanosystems. Boundary conditions often need to be described in terms of potential surfaces. Surfaces are not geometrically smooth, but periodic according to the locations of atomic nuclei. Friction occurs not due to the plastic deformation of asperities on mating surfaces, but to phenomena such as thermoelastic damping and phonon viscosity when atoms slide past each other. Electrostatic forces dominate over gravitational forces by orders of magnitude; there is no role here for natural convection. Structural components, no matter how stiff and strong, are in constant motion due to the thermal noise in the system. The fluids are described in terms of individual molecules in constant motion.

Jan 1, 2006

By J. Antonio Barrera-Godinez, S. E. James, J. Sun

The solvent extraction separation of iron from a zinc sulfate medium using DEHPA was investigated. After loading, the ferric ions were reduced in the organic phase using metallic zinc. The ferrous ions produced could be easily stripped into a sulfate solution with pH values in the range of 1.4 to 2.0. The small, laboratory scale pilot system used in this study allowed for continuous cycling of the organic and strip aqueous solutions. It was possible to establish and evaluate a series of steady state conditions under selected operating paiameters. The effects of processing parameters such as solution chemistry, flow rates, zinc metal loading and pH on iron recovery and efficiency were also evaluated. Under proper conditions, it was possible to remove about 5 g/L iron from the organic phase in one stage and to produce a concentrated iron sulfate strip solution containing ferrous ion concentrations in the range of 90 to 130 g/L. Preliminary feasibility tests were also made on electrowinning metallic iron from the strip solutions and crystallizing ferrous sulfate as a means of making a marketable iron product.

Jan 1, 2000

By Mingzhou Li, Lin Wu, Changren Tong, Fengli Yang, Shaohua Yang

"According to characteristics of Tm, Yb and Lu enriched oxides composition and problems in its traditional extraction separation process, the computer simulation of a optimized fuzzy extraction separation process, in which three products with high purity(>99.99%) could be obtained at same time, was carried out. Distributing Curves of every element in both organic and aqueous phases were worked out. Distribution rules of rare earth elements in every stage of the optimized extraction process were studied. The computation results of economical and technical index showed the consumption of the acid and base chemical reagents in the optimized process would be saved more than 30%.IntroductionFor the solvent extraction separation process of rare earths, countercurrent extraction process was widespread in the industrial practice. Normally, rare earth ions were extracted by the saponificated extractant and transferred into the organic phase, where the acidic extractant was saponificated by the base firstly. Then, the loaded rare earth ions were stripped from the organic phase into the aqueous phase by the acid. Therefore, the acid and the base were the main consumptions in the process, and the equilibrium acid of the stripped rare earth solution was one of the main pollution resources. Meanwhile, for the heavy rare earths, such as Tm, Yb and Lu, stripping was more difficult, and the equilibrium acidity of the stripped rare earth solution was higher, so the acid consumption increased greatly."

Jan 1, 2012

By A. V. Tarasov

The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs and high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, as well as mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: -Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); -Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially, at the stage of liberation (chemical upgrading) of minerals, are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent). An example is processing of low-grade refractory pyrrhotite concentrates using autoclave liberation of feed material under pressure of a new reagent, i.e., sulfur dioxide. The use of sulfur dioxide ensures a significant improvement in the recoveries of non-ferrous metals and platinoids to sulfide concentrate and smelting of the latter increases the capacity of the smelting units employed and minimizes the yield of discard slag and loss of metals in slag; in addition, it resolves the problem of sulfur dioxide utilization.

Jan 1, 2003