Search Documents

By Atsushi Shibayama

The aim of this research was to develop a copper recovery process from mine tailings (0.34%Cu) using flotation followed by high-pressure oxidative leaching (HPOL) and solvent extraction. The results of HPOL using the concentrate of mine tailings obtained by flotation under the optimal conditions of the previous study shown that an efficient copper dissolution of 94.4% was achieved in an H2O media, while the copper concentration of PLS reached to be 2.9 g/L. The solvent extraction of PLS obtained from the optimal HPOL showed that 91.3% copper was recovered in stripped solution under the determined optimum conditions, in which the copper concentration achieved to be 44.8 g/L. Finally, a proposed copper recovery process from the concentrate of mine tailings was developed by combination of HPOL and solvent extraction, while a total copper recovery of 86% was achieved.

By J. L. Liow

Studies have been carried out on the causes and effects of slopping in an annular cylindrical geometry such as the top submerged combustion reactor. Properties of standing waves formed such as the wave profile, period, pressure distribution and velocity have been derived analytically. The wear profile due to wave erosion was calculated based on the assumption of linear motion and that the wear is a dissolution process. The use of the j, factor showed that the wear was proportional to the square root of the wave velocity at any point. Using the dimensions of the lsasmelt reactor given by Errington et al. (1987)[11, the wear profile due to wave erosion was calculated using the analytical solution. The wear profile calculated was shown to have a maximum just below the initial bath surface. The wear was found to be concentrated in the region where the first asymmetric standing wave was most active. The results showed that the refractory near the bath surface will be affected by wave erosion, more so than any other parts of the reactor. The contribution of wave erosion on wear must be accounted for in assessing the total refractory wear of a vessel in which slopping exists.

Jan 1, 1991

By Tomas Astorga

APEC, the Asia Pacific Economic Cooperation is the forum of 18 economies, having a combined GDP of approximately 56% of the total world income, and over 45% of global trade. Its mining sector produces a large portion of the main minerals and metals in the world. In 1997, APEC economies produced 67% of world copper output, 55% of gold, and over 45% of other base metals. Mining in APEC captures more than 60% of the total mining investment in the world. Against this background, the Expert Group on Minerals and Energy Exploration and Development, in short GEMEED, was created in 1996, under the auspices of the APEC Energy Working Group. The sustainable development of mining activities is a main concern in APEC and GEMEED. Several programs related to the subject are actively being pursued by the Expert Group. Among them, it should be noticed the creation of an Environmental Cooperation Sub Group coordinated by Japan, whose main aim is to encourage proposals related to the environmental soundness of mining projects in the region. Also, it should be noted the existence of a Database Steering Committee whose focus is the development of an information network related to mining opportunities in the region GEMEED is a gathering of experts from all the APEC economies. As such, it represents a privileged forum to discuss policy issues related to mining. On this regard, the paper focuses on concrete actions taken by GEMEED to enhance the sustainability of the copper activity in the region.

Jan 1, 1999

By M. Misra

The bacterium?Mvcobacterium Phlei has a demonstrated potential to be used for the flocculation of a variety of finely divided minerals. The microorganism possesses both hydrophobic surface and high negatively electrostatic charge. It can adhere to many mineral surfaces ?if the charge and hydrophobic interaction? between the microorganism and the minerals are favorable to adhesion. Experimental results showed that the dolomitic phosphate slime from Florida and fine hematite can be :readily flocculated from dilute suspension.. In the case of dolomitic phosphate slime, a consolidated sediment containing 24'-25 weight% :solids can be obtained from .a dilute slurry .in a short time. Sediments obtained from hematite flocculation are rather massive and more .consolidated than phosphate slime. Mycobacterium Phlei has a specificity for selective flocculation of hydrophobic fine coal particles from pyrite and ash containing minerals. Because of mutual hydrophobic interaction of coal and Mycobacterium Phlei, it was noticed that coal particles appear to be strongly held in the aggregate by adhesion or bridging of bacteria. However, Mycobacterium Phlei is not a good flocculant for either associated pyrite or ash present in coal.

Jan 1, 1991

By Larry M. Southwick

The smelting of copper and other non-ferrous metals have made considerable advances over the last 125 years. Many of the ideas and processes currently in use were attempted early in the history of smelting and were unsuccessful. Often the cause was incomplete understanding of the metallurgy involved, inadequate refractories, poor materials of equipment fabrication or trying too many new ideas at once. With time, these problems get solved and the technologies become commercialized .These were processes whose time had not come when originally proposed, but did eventually. On the other hand, there have been some concepts whose time will never come. They were impossible then and they are impossible now. The people that dream these up were either crackpots (they didn't know what they were doing, but thought they did), or charlatans (they knew they didn't know what they were doing, but didn't care). Both rely on bad science to propose metallurgical absurdities. These too have their place in the development of technology, though mostly negative, and several examples will be discussed in this paper. Three from around the turn of the century will be covered, as well as one from this decade. The last demonstrates that the art of creating absurdities has not withered, even after ninety years of scientific sophistication, and some can even be patented. The first three reached field trials due to the gullibility of company management. The last arose from a fortuitous mis-operation of a plant which solved a problem, but the explanation and patent which arose are metallurgically impossible.

Jan 1, 1999

By T. Malvik

Norway is a big producer of ferrosilicon and silicon metal. The raw material is quartz and quartzite and large quantities from both Norwegian and foreign sources are used. The demands maade on both the chemical purity and the thermomechanical qualities of the quartz/quartzite have increased in recent years in an attempt to reduce energy consumption and to improve utilization. Control of the chemical quality of the raw material is relatively easy by means of routine analysis, but it is more difficult to find a suitable method for testing the thermomechanical properties. A rapid test method to define high quality quartzite deposits for use in the metallurgical industry has been developed. The method is based on a combination of chemical analysis, dilatometry, thermosonimetry and cathodoluminiscence.

Jan 1, 1989

By James D. Navratil

Neutral bifunctional organophosphorus solvent extractants (such as carbamoylmethylphosphonates and carbamoylmethylphosphine oxides) strongly extract lanthanides and actinides and do not extract more than 40 other elements from mineral acids. Because of their excellent properties they have been found useful for F-element recovery and purification processes. A brief overview of the lanthanide and actinide extraction chemistry of these reagents will be given.

Jan 1, 1990

By Peter K. Liaw, Niann-i Yu, Wei Zhao

"For a plain-weave Nicalon ™ fiber fabric-reinforced silicon carbide (SiC) ceramic composite, little attentation has been paid to the effect of fabric stacking sequence on its mechanical behavior. In this paper, fiber-fabric stacking sequence effects on the elastic stress distributions, ceramic matrix-cracking stress, effective elastic moduli, and flexural strengths of laminated flexural test bars are quantified. A quantification model is established based on the combination of classical laminated plate theories and a fiber undulation model developed by Chou et al. A FORTRAN program is compiled to implement the modeling, which can be run in a SUN work station. The mechanical performance of a continuous fiber-reinforced ceramic-matrix composite (CFCC) with a [0/30/60] lay-up was analyzed and predicted. The variation in the fiber-fabric stacking sequence can vary the elastic stress distributions along the thickness direction of specimens, magnitude of ceramic matrix-cracking stress, effective elastic moduli of the laminate, and crack initiation sites as well as fracture modes. Moreover, all these factors contribute to scatter in flexural strengths of the CFCC.I. IntroductionWith enhanced fracture toughness and the ability of non-catastrophic (graceful) failure behavior, CFCCs are currently under evaluation for high-temperature structural applications in heat exchangers, combustors, hot-gas filters, boilers components, first walls and high-heat flux surfaces gas turbines, space vehicles and nuclear reactors.[1-8] Extensive applications of CFCCs by industry are still hampered by an insufficient understanding of the mechanical behavior, and sometimes, the lack of a well-developed and widely accepted design philosophy, in addition to the high-production costs."

Jan 1, 1998

By R. Togashi, T. Aichi, T. Yamada

"A new automatic material- handling system for cathode transportation has been developed. The first system went into service in August 1994 and the remains will be operational subsequently.Because of the complex cell-layout and the number of cells in each row, the critical part of this work was achieving a planned cycle time. This cycle time is determined by the power costs.The central monitoring system for machine operation was started in June 1996, using original application software based on MICROSOFT EXCEL ® on WINDOWS 95® .As a result, only one person is now required to operate both a crane and a stripping machine for one row of about 50 cells.INTRODUCTIONMainly due to the strong yen and the relatively low price of metal, the zinc refineries in Japan are being forced to reduce production costs again and again.The trend of lijima's production costs is shown in Figure 1.[1] The ratio of labor costs becomes gradually higher. Therefore it is effective to reduce the labor costs in order to reduce the production costs. In Japan, electricity cost during day time is too high to produce zinc at a reasonable cost, that is why the actual production is far from the capacity of production at a cell house. That means a plant in Japan has the disadvantage of relatively low productivity for cell house operation.Saving labor costsSome automatic cranes have been applied to save labor costs for cell house operation in the world. In consideration of the mentioned low productivity, the installation of an Automatic Cathode Transfer (ACn system for transportation of cathodes was planned without changing the present cell house and stripping machines to lower the investment costs. The ACT system must keep up with the stripping machine which is able to strip deposit zinc from a cathode sheet at the rate of 6 seconds.The fifth ACT system of seven was installed in August 1996 and the last one will be operational subsequently."

Jan 1, 1997

By Banqiu Wu

Zirconium carbide powder has been synthesized from zircon concentrate and methane using a high temperature plasma reactor, a non-transferred DC plasma torch was used as heat source. A high temperature filter consisting of graphite felt was designed, built and operated to separate the zirconium carbide from silicon carbide during the process. Characterization of the collected powders was done by wet chemical analysis using Atomic Absorption (AA), Scanning and Transmission Electron Microscopy (SEM and TEM) and by X-Ray Diffraction (XRD). It was found that the zirconium carbide purity was around 95% with silicon carbide being the primary impurity. The powders had particle sizes between 30 and 80 nm. The effect of several experimental variables are presented as well as temperature and velocity profiles calculated in the reactor.

Jan 1, 1997

By M. Sahoo

The development of new alloys containing bismuth and selenium for potable water supplies are reviewed. The new alloys are replacements for the leaded red- and semi-red brasses by the low-lead alloys, SeBiLOYS I and II, for sand casting, and SeBiLOY III replaces the lead containing yellow brass, C85800, for permanent mold casting. As the new alloys use bismuth and selenium, the supply and demand of these elements are discussed. The key casting characteristics discussed are: tendency to dross formation, freezing range (liquidus and solidus temperatures), fluidity, resistance to hot tearing, microstructures, mechanical properties, machinability, grain refinement and corrosion behaviour.

Jan 1, 1999

By Ramiro Escudero

Michoacan?s beach sands with interesting concentrations of ilmenite were studied to produce titanium by hydrometallurgical techniques. Nevertheless, among titanium species, there are different additional components of Michoacan?s beach sands which could be of interesting applications. Some of them are likely to be applied for the manufacture of nanocrystalline ceramics. Although, the most applied mineral dressing to treat these kind of sands, that contain magnetic species (i.e., ilmenite, magnetite), is a combination of gravity separation and magnetic separation, it could be of a great deal of benefit to apply the information regarding the surface characteristics of the sands? components, in order to study the application of flotation technologies to separate selectively those species with commercial value.

Jan 1, 2006

By M. A. Vera

This paper proposes a simple two-parameter model for the typical inverse relationship between recovery and flotation concentrate grade. The model is based on the mineralogical limitations imposed by the material properties. One parameter (R*) describes the proportion of metal content which is floatable, and the other (b) is the rate at which the fastest floating particles are being contaminated by the other less valuable particles present in the mineral system. One significant feature of the recovery-grade curve is that initial recovery (i. e. R ? 0) is at the purest attainable mineral grade, (but as recovery rises the cumulative grade of the concentrate tends to the feed grade. The ideal recovery-grade curve for a particular mineralogical system can be obtained by release analysis: the release analysis curve determines the maximum or limiting separation efficiency. The model proposed in this work is similar to the linear recovery - cut-off grade model of Dell (1), but has the advantage of describing the whole curve.

Jan 1, 1999

By lndu S. Das

An analytical simulation of the material characteristics of Inconel 718 is developed and bounds for mechanical and microstructural stability are obtained for isothermal and temperature-dependent cases. Experimental flow stress data using hot compression tests are reported for a wide range of temperature and strain at various strain rates. A parametric study of strain rate sensitivity, dissipation and entropy are presented. A complete set of processing maps delineating the stable and unstable regions are developed to help define the most efficient means of manufacturing an Inconel product.

Jan 1, 1992

By W. C. Chang

Phases and magnetic evolutions of melt spun Nd9.5(Fe1-xCox)85.5B5 (x=0, 0.05, 0.1 and 0.15), (Nd1-yLay)9.5Fe85.5B5 (y=0, 0.0.5, 0.1; and 0.15) and (Nd0.95La0.05)9.5(Fe1-zCrz)81.5B9 (z=0, 0.033, 0.067 and 0.1) nanocomposites: have been investigated. It was found that a. dilute Co substitution for Fe, x=0:05-0:15, in Nd9.5(Fe1-xCox) 85.5B5 improved not only Curie temperature but also the remanence and maximum energy product. Partial substitution of La for Nd in(Nd1-yLay)9.5Fe85.5B5 may suppress the grain growth of the materials during thermal treatment. Exchange coupling between the Nd2Fe14B and a-Fe was found: to increase with increasing La content. A dilute La-substitution, y=O. 10, has proven to decrease the optimum wheel speed required for preparing melt spun ribbons with better magnetic properties; Furthermore; a slight substitution of La for Nd in (Nd0.95La0.05)9.5(Fe1-xCrx)81.5B9 nanocomposite reduced the crystallization temperature of the over-quenched ribbons and led to the formation of a multiple phases mixture. Nevertheless, a dilute Cr addition increases the Tg of (Nd0.95La0.05)9.5(Fe1zCrz)81.5B9 and also suppresses the formation of the undesired (Nd,La)2Fe23B3 and Fe3B phases: Cr was found to play an important role in grain smoothening or magnetic separation which consequently increased the Hc of Cr-containing materials.

Jan 1, 1997

By Milton Manrique

The thermal decomposition of ilmenite concentrates in a non-transferred arc; thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and particle size was studied. Products were characterized by XRD, SEM, TEM and ICP techniques. Free energy minimization plots were used to predict the thermodynamic behavior of the system under different operating conditions. The results of this investigation showed a significant segregation process where titanium-rich products are collected in the reactor, while iron-rich products are collected in the quenching box and filter. The average size of the product is in the sub- micron range. Titanium nitride was formed and condensed in the reactor zone when using an argon-nitrogen mixture as the plasma gas.

Jan 1, 1998

By Pranav Deshpande

The wear behavior of metal matrix composites differs from that of the monolithic metallic counterparts because composite materials have multiple constituents in their structures and these constituents wear at different rates. It was observed that under low wear stresses, abrasive wear prevailed. As the wear stress increases, pullout of reinforcement occurs and both abrasive wear and wear due to pullout contribute to the overall composite wear. A model of wear taking into account both types of wear has been developed. A critical pullout wear stress was suggested for each composite. Below the critical wear stress, no pullout of reinforcement occurs. It turns out that the critical wear stress simply equals to the ratio of the interfacial strength between the matrix and the reinforcement to the friction coefficient between the reinforcement and the wear counter surface. The critical wear stress is independent of the particle size of the reinforcement. From data on wear of 53% WC composites, the equation of wear for 32% WC composites was obtained. Experimental results agreed well with the predicted wear rate of this composites. This provides an excellent verification of the wear model developed by Lin and Deshpande. Wear data from Modi et al. in the literature were also perfectly fitted with the model.

Jan 1, 2006

By David N. Hanlon

The effect of high-temperature plastic deformation of the austenitic phase (y) on the subsequent phase transformation to ferrite (a) has been experimentally investigated, and modelled using a physically-based model. The effect is of importance for steel sheet, in view of me significance of the phase transformation with respect to the eventual properties of the material. In this paper the kinetics of the y ? a phase transformation has been studied after different degrees of prior deformation. The degree of deformation is varied by applying different deformation temperatures and strain rates, and by allowing a varying extent of recovery and recrystallisation. Consequently, both dynamic and static recovery and recrystallisation have been involved. The dilatometric observations on the phase transformation have been modelled using an interface-mobility model, in which the effect of the dislocation structure is introduced as an additional driving-force term. The effect of the stored energy on the nucleation process, which appears to be affected more strongly than the growth of ferrite, is examined in terms of the classical nucleation theory.

Jan 1, 2001

By J. Garvey

The new Cyprus Miami electrolytic copper refinery was commissioned in October 1994. The refinery has been operating at its design capacity of 190,000 short tons per year, and in recent months to 110% of design capacity, producing high-grade electrolytic copper cathodes. Basic and detailed engineering, performed by Fluor Daniel Mining and Minerals, incorporated state-of-the-art technology, including stainless steel cathodes, automated electrode handling, fine-filtering of the commercial electrolyte, autoclave leaching of the anode slimes and other techniques. The major design goals have been safety of operation and quality of the product. Relatively high cathode current densities of 30 amperes per square foot and greater have been applied since start-up. Cathode current efficiencies of over 94% have been achieved since the latter part of 1997. The cathodes were certified on the Comex and LME markets during 1996. ISO- 9002 certification is in progress and should be completed during the first quarter of next year. This report discusses some of the studies that were performed to obtain an optimum layout for efficient materials handling and to create optimum conditions for producing high quality cathodes. A description of the design and operation of the anode slimes facility, including decopperizing with autoclave leaching, is provided. Finally, a description of the start-up experiences and present operation of the electrorefinery are presented.

Jan 1, 1999

Laboratory trials were performed in an induction furnace to study droplet formation during lance blowing. Compressed air was blown on a molten iron bath consisting of iron alloyed with carbon and silicon. Steel droplets were collected using a specially designed sampler. The average steel droplet composition and the oxide layer thickness were determined using scanning electron microscopy combined with energy dispersed spectroscopy. In addition, the concentration gradient of elements was determined using a microprobe. It should be noted that a special technique had to be developed in order to prepare the droplet sample. The size distribution and composition of the droplets was also determined using the microprobe. It was found that the carbon content in the droplets was lower than the carbon content in the bulk.

Jan 1, 2006