Search Documents

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By James E. Hoffmann

This paper briefly reviews the conventional technologies employed for the treatment of copper refinery electrolyte bleed. The strength and weaknesses of conventional practice will be reviewed and a number of process options to address the weaknesses of present process technology will be described and evaluated. The effect of process selection upon energy consumption and the environmental aspects of process effluent control will be discussed.

Jan 1, 1997

By T. Shimizu

In Japan, the emission standard of selenium in effluent was set at a maximum of20 mgll in Feb. &apos;94 for the first time, and it is scheduled to be further decreased to a maximum of 0.1 mg/I from Feb. &apos;97 due to tightening of the Water Pollution Prevention Act. Selenium (IV) and (VI) are generally found in effluent from precious metals refineries. Although selenium (IV) can be easily eliminated by some reducing agents, selenium (VI) is more difficult to be reduced. Therefore, many smelters are having difficulty in complying with the new emission standard. At Mitsubishi Materials&apos; Naoshima smelter, the behavior and the elimination of selenium in effluent have been extensively investigated. As a result, it was found that two strategies were particularly effective. One of them is improving the overall operation of precious metals refinery, that is, feeding uniformly the effluent to the waste-water treatment plant, reducing the effluent volume by recycling and recovering more selenium (IV) in the effluent. The other is eliminating selenium (VI) in the effluent from the precious metals refinery. It was found that selenium (VI) can be effectively reduced by using hydrazine under high? sulphuric acid concentration and high temperature conditions. By using these measures, it is considered that Naoshima Smelter will be able to comply with the new emission standard.

Jan 1, 1996

By Xinghui Meng

The recovery of platinum and palladium from automotive catalysts has been investigated by leaching in iodide solutions with oxidants including oxygen and iodine in an autoclave. An ammonium salt was presented in a neutral leaching solution as a key leaching reagent to achieve high recoveries of the platinum group metals (PGM). The effect of temperature, and concentrations of oxidants and of ammonium salt on the recovery of PGM was examined. Under the experimental conditions studied, the recovery of platinum and palladium was found to be greater than 95%. An economical assessment of this process has also been examined and discussed.

Jan 1, 1995

By Guo Chen, Jin Chen, Jinhui Peng

In this study, the influences of the green evaluation variables on the characterization of microwave shaft furnaces were systematically investigated. These variables include: resource consumption, environment impact, production cost, processing time and quality of microwave shaft furnaces. A greenness evaluation index, evaluation system and evaluation model of microwave shaft furnaces were established. The analytic hierarchy process and fuzzy comprehensive evaluation were applied to the evaluation process. Resource consumption and environment impact had a statistically significant effect on the green evaluation of microwave shaft furnaces. The results indicated that green evaluation techniques can be applied effectively and efficiently to the process manufacturing of microwave shaft furnaces.

Jan 1, 2015

By JiaPeng Xu, Brian Lo, Uday B. Pal, Yihong Jiang, Soumendra N. Basu

"The Solid-Oxide Oxygen-Ion-Conducting Membrane (SOM) electrolysis process has been successfully tested on a laboratory scale, producing silicon directly from silica in a cost-effective and environmentally friendly way. A yttria-stabilized zirconia (YSZ) tube, closed at one end was employed to separate the molten salt containing dissolved silica from a liquid metal anode placed inside the YSZ tube. When the applied electric potential between the liquid tin cathode in the molten salt and the anode exceeds the dissociation potential of silica, oxygen ions are pumped out of the molten salt through the YSZ membrane and oxidized at the anode while the silicon cations in the flux are reduced to silicon at the liquid tin cathode. The presence of high-purity silicon crystals on the surface of liquid tin cathode was confirmed by scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS). Silicon crystals were extracted from tin cathode by chemical etching.IntroductionPhotovoltaics (PV) generate electrical power by using solar cells, and dramatically reduce the emissions of greenhouse gases (GHG). Through 2006 to 2011, it grew the fastest of all renewable technologies with operating capacity increasing an average of 58% annually [l]. However, the cost of manufacturing solar-grade silicon (SoG-Si) for high-efficiency solar energy production represents a major barrier to achieving the industrial goal for solar power of $1/Wp (watt at peak exposure) which would enable widespread grid parity. The current contract price of silicon to PV manufacturers is $50-$60/kg, with the spot market in 2007-2008 showing prices as high as $300/kg [2]. This makes the development of low cost and environmentally friendly manufacturing of high purity silicon very important."

Jan 1, 2013

By Germán Richter a

To comply with the chilean air quality regulation requirements, the Hernan Videla Lira Smelter which is a custom smelter having to cope with a wide variety of concentrates, has developed a two-step modernization plan. The main steps are: - A second acid plant of 80,000 Nm3/hr to be operating at the end of 1996. This will increase the sulphur capture from 43% to 701/o in association with the replacement of the Hoboken converter by a second PS-converter to reduce the operation problems resulting from the treating of high garde matte. - Oxygen enrichment, is going to be incorporated in 1998 in the Teniente Converter and PS-converters in association with tuyere injection of dry concentrates, increasing the sulphur capture to 90 - 93% of sulphur inputs. By this program, sulphur emissions will be decreased from 40,000 tpy today to less than 8,000 tpy and in this way to carry out the environmental regulations.

Jan 1, 1996

By Taner Kavas

The refractory bricks of a rotary cement furnace containing of alumina and magnesium chromite were studied in order to determine whether they could be used in the concrete production as aggregates. Three mortars were prepared by mixing 1 part cement, 3 part aggregate materials, 0.5 part water by weight and mechanical, chemical, thermomechanical and microstructural characteristics were evaluated. The compressive and bending strength of samples were determined after 2 and 28 days curing. Resistance to chemicals were established by calculating the weight gain of mortars stored in 2 % HCl solution for 1 h and 24 h. Thermomechanical characteristics were determined by measuring the compressive strength of heat treated specimens at temperatures of 400 °C, 600 °C and 800 °C. Consequently, magnesium chromite containing waste brick aggregates have given the best results.

Jan 1, 2006

By David G. C. Robertson

A new approach is described for the calculation of the kinetics of metal/slag, metal/slag/gas, and metal/matte/slag/gas reactions. The algorithm assumes that equilibrium is achieved at the interface between phases, and uses an equilibrium solver (such as SOLGASMIX) to compute the equilibrium state at the interface at each time step during the reaction. For multiple phase systems a number of unit operations, representing the different phases and interfaces, must be connected together in a reasonalbly complex manner, and the METSIM software package has been utilized for this purpose. The new approach is superior to the SMAK software developed by the author and his co-workers over the past decade, for the reasons discussed in this paper.

Jan 1, 1995

By Jun Li

Rate processes of silver cyanidation were studied with the objective of understanding the reaction mechanism. The research was divided into three sections: anodic dissolution of silver in cyanide solutions, cathodic reduction of oxygen on silver surfaces and the direct leaching of silver in oxygenated cyanide solutions. The charge transfer steps plus the diffusion of reactants from bulk solutions to the silver surface were identified as rate-limiting and the rates of both anodic and cathodic reactions can be calculated using the Butler-Volmer equation and Fick&apos;s first law. Based on mixed potential theory and the results of electrochemical studies, a comparison of the rate obtained from direct leaching with that predicted from the calculation is made. Calculated results agree well with the experimental data.

Jan 1, 1992

By F. Begazo

The most common approach to increase production in copper refineries is to increase current densities. However, if these increases are not well thought out beforehand and are not properly and effectively controlled, the end results could be reduced plant performance and a deterioration in cathode quality. Both of these factors result in lower efficiencies and increased costs. At the Ilo Refinery of Southern Peru Copper Corporation, a modernization and expansion program was implemented shortly after the Refinery was purchased from Minero Peru, in 1994. This program was intended to increase production from 195,200 mtpy of cathode to 227,000 mtpy over a 3-year period. Part of this production increase would come from increasing current density. During the period from 1994 to 1997, current density at the Ilo Refinery was increased from 218 A/m2 to 230 A/m2, while plant efficiencies were maintained at consistently high levels. The current efficiencies were maintained at >97.5% and time efficiencies were maintained at >98%. During 1998, additional increases in current density were implemented while the high plant performance was maintained at the same levels. By the end of 1998, the current density was 241 A/m2, while current efficiency and time efficiency of 98% were maintained. This paper describes the control processes used at the Ilo Refinery to maintain high plant performance levels while increasing the current density. Additionally, expected plant performances from extended test programs at current densities up to 280 A/m2, for future production increases, are reviewed and discussed.

Jan 1, 1999

By David B. Dreisinger

The total pressure oxidation treatment of arsenical copper ore and concentrate from the El Indio mine of Banick Gold was tested in benchtop autoclave treatment. The concentrate oxidation typically achieved ~95% copper extraction. Copper extraction was limited by the reprecipitation of a complex precipitate containing arsenic. Gold extraction by cyanidation of the oxidation residue was around 95%. Silver extractions were less than 10% due to the formation of argentojarosite in the autoclave. The total pressure oxidation of the whole ore sample was more successful. Copper extractions of 98-99% were routine achieved. Gold extraction by cyanidation was +95%. Silver extraction could be increased to as high as 95% by using the lime boil treatment. A process flowsheet was proposed based on the results achieved. Copper recovery was proposed by direct solvent extraction and electrowinning of copper by treating the dilute solution from the autoclave discharge.

Jan 1, 1999

By Peter Fischer

A demonstration plant for QSL technology with a continuous through-put of up to 10 t/h concentrate has been in operation at the Berzelius smelter, Duisburg, Germany since early 1981. In the QSL-process, both oxidation and reduction steps are performed in a single horizontal long cylindrical reactor. In the present demo-reacior, 2.5 M diameter by 22 M long, these steps are separated by a low partition wall with an underflow opening, to prevent backmixing of slag. -Tests on a variety of concentrates, including high-lead Missouri-type material and lower grades, have shown recoveries and consumables indicating very attractive economics. Investment cost estimates further enhance the economic attractiveness. Environmental protection afforded by the QSL system is a major advantage. The process has proven its reliability and versatility and is now ready for commercialization. Continued test work, including smelting secondary lead materials, is planned.

Jan 1, 1983

By J. W. Dini

Introduction The mission of the Materials Fabrication Division (MFD) is to provide fabrication services and technology in support of all programs at Lawrence Livermore National Laboratory (LLNL). MFD involvement is called for when fabrication activity requires levels of expertise, technology, equipment, process development, hazardous processes, security, or scheduling that is typically not commercially available. Customers are encouraged to utilize private industry for fabrication activity requiring routine processing or for production applications. MFD is .a large diversified service organization including approximately 400 full time employees. The group provides a wide variety of processes including all common machining and fabrications operations, laser and water jet cutting, electrical discharge machining, lapping, electron beam and laser welding, vacuum brazing, heat treating, forming, electroplating and metal finishing, optical polishing and grinding, vacuum coating, vacuum engineering and a variety of plastics operations. These operations occupy more than 1,250,000 square feet of floor space. For more detail on the many fabrication related services available from MFD, see Reference 1.

Jan 1, 1992

By Fernando Guevara

Many smelting and slag-cleaning furnaces operate with cooling systems designed to freeze a slag layer over the refractory to protect it. The fluid flow and heat transfer conditions associated with the freeze layer and mushy zones are poorly understood. These phenomena were simulated with a small-scale room temperature, 2-dimensional model, using an aqueous solution of calcium chloride to simulate the slag. Reasonable similarity with conditions encountered with copper and nickel smelting systems was achieved (Pr 50 and Ra 108, in the laminar-turbulent transition). Measurements of the freeze layer development and velocities were made with the Particle Image Velocimetry (PIV) technique. Direct Numerical Simulations (DNS) were also made of the unsteady fluid flow and heat transfer problem. It was found that the solidification process is well described using an improved model for high molecular viscosity in the mushy zone. Solid front growth, isothermal profiles, velocity profiles and heat transfer through the walls showed good agreement between the PIV and DNS results. Experimental and numerical velocity profiles close to the freeze layer show a parabolic behaviour in the vertical velocity profile which is completely different from the calculation of heat transfer using a sharp interface model. The reason for this is attributed to the effects of the mushy zone with a high viscosity and high shear stresses acting on that area.

Jan 1, 2006

By Y. Y. Sheng

Plume flows created by gas injection into liquid metals have been studied extensively, however the dynamics of bubbles within the plume have not received adequate attention, particularly for large, irregular bubbles, characteristic of the processing of liquid metals. The present model uses a combined Eulerian-Lagrangian approach in which an estimated void fraction distribution is used to calculate the liquid flow field with a conventional Eulerian scheme. The trajectories of bubbles are then computed in a Lagrangian manner using the estimated flow field, and experimentally measured information on bubble drag coefficients&apos;, lateral migration due to lateral lift forces and interaction with turbulent eddies, and variation in bubble size due to break-up. Turbulence in the two-phase zone is modeled with a modified k-e model with extra source terms to account for the second phase which have been recently determined by the present authors. The computed void fraction and turbulent liquid flow field distributions are in good agreement with experimental measurements.

Jan 1, 1993

By E. Kozeschnik

A new model is presented for the simulation of the evolution of precipitates in a multi-component multi-particle multi-phase environment The mathematical formulation as well as the physical background of the model are briefly introduced and its capabilities are discussed on the example of a precipitation sequence in a complex steel. Keywords: Modeling, precipitation kinetics, nucleation, growth, coarsening

Jan 1, 2003

By A. Lackner

Using the CFD software package FIRE, the smelting process inside a cyclone reactor is modelled. The fluid flow is calculated 3 dim., using different turbulence models. The effects of design parameters (length and diameter of the cyclone, concentrate feeding tangentially or from the top,..) and operating conditions are investigated. Single particle traces illustrate how to increase particle retention time before the particles reach the liquid film flowing down the cyclone wall. Moreover a two phase flow approach is developed, based on the "Discrete Droplet Model". The position, velocity, diameter and temperature of each reacting particle is described. The results show the advantages of top concentrate feeding, large height/width ratio of the tuyeres and increasing number of tangentially gas inlets.

Jan 1, 1995

By M. C. Nielson

The paper describes the design and operation of pulsed columns as replacements for conventional mixer/settlers. The advantages, which the columns offer, include a reduction in real estate for the plant, elimination of diluent evaporation, containment of noxious vapors and reduced crud formation. In addition to the description of operation, the paper presents the findings of laboratory tests of pulsed columns extracting copper from pregnant leach solutions and also delineates potential advantages of the pulsed column in copper solvent extraction.

Jan 1, 1999

By David E. Hardt

"One of the critical variables to be controlled during arc welding is the size or geometry of the weld pool. The measurement of pool geometry has become an increasingly important problem with the advance of welding automation and control, and this paper addresses that problem. The basic concept of pool size estimation via measurement of pool dynamics is presented. The theory underlying this concept is discussed and is followed by a review of the current work in this area. It is concluded that pool dynamics can be characterized by natural frequencies of oscillation, for stationary welds, and that these can be measured by appropriate signal processing performed on the arc voltage. However, it appears that only full penetration welds show a strong correlation between weld size and natural frequency. Also, the extension of these results to the realistic case of moving welds has yet to be considered in detail. Nonetheless, this method of in-process measurement for real-time weld process control is still quite attractive where applicable since it can be accomplished simply by modifying the arc current schedule and by signal processing of the arc voltage.INTRODUCTUIONThe study of welding process control has been dominated by research into methods of in processing sensing of the weld pool geometry. While it has been shown feasible to measure the topside pool geometry using video methods [1,2], the penetration or backside bead width have remained elusive quantities. This is particularly true if a topside sensor location is required.The concept of using weld pool motion as a pool geometry sensing method was proposed by Hardt et al. [3] and later demonstrated by Hardt and Zacksenhouse [5] and Richardson and Renwick [6]. The concept is based on the fluid dynamics of a pool constrained by a solid container and by significant surface tension forces (i.e. a small shallow pool, not a ""pond"" or ""lake""). Such a pool, if subjected to external forces, will exhibit a surface motion is a function of that force, the properties of the fluid, the surface tension, and the shape of the container. Thus, if this motion can be excited and measured, and the relationship to the pool geometry determined, a means of sensing pool shape will exist."

Jan 1, 1986