Search Documents

By Xiang Lan

A strain of Thiobacillus ferruuxidans No. 8 was isolated from the acidic mine water of an arsenopyrite deposit, South China. It has been found from the experimental results that the growth of bacteria was inhibited by flotation agents. The order of toxic effect of different flotation agents on the growth of Thiobacillus ferrooxidans is ethyl xanthate > butyat ammonium aerofloat > butyl xanthate ? isobutyt xauthate >? flother No. 2 oil. The bioteaching treatment of arsenic and antimony-bearing gold concentrate in Longshan mine, Hunan province, China, was influenced considerably by the presence of flotation agents. The possible causes of the influence of flotation agents were discussed and an improved method was suggested.

Jan 1, 1991

By Susumu Okabe

Top blowing lances are employed by the Mitsubishi Continuous Copper Converter for the continuous supply Of reaction gases into moken bath. In order to minimize the refractory wear caused by the interaction between the furnace lining and the melt splash. optimum furnace design and blowing condition are? required. An empirical equation obtained by the physical model study enables the estimation of the splashing rate on a vel1ical plane at a certain distance from the lance.

Jan 1, 1996

By P. Schloth, H. van Swygenhoven, N. Chobaut, J-M. Drezet

"In the current trend toward thicker aluminium plates, a major concern is the stress build-up during quenching which causes distortions during machining. Indeed, cooling rates are not high enough, especially at the core of such thick plates, to prevent any precipitation and quench induced precipitates lower the hardening potential. Multi-scale modelling is required when predicting macro-scale stresses after quenching for thick heat treatable aluminium components. The reason is the instantaneous strong coupling between phase precipitation at the nano-scale and material hardening due to precipitation or softening owing to solute depletion at the microscale. For thick parts, quenching intensities decrease when going from the skin to the core of the component, thus introducing a gradient of nanostructure and consequently a gradient of mechanical properties. In addition, large thermally induced deformations lead to high macroscale residual stresses although part of them is relaxed by plastic deformation. These stresses have been measured in water quenched thick plates of 7040 and 7449 aluminium alloys using neutron diffraction and layer removal techniques and the results when compared with a thermomechanical finite element model of quenching highlight the influence of precipitation.IntroductionIn the processing route of heat-treatable aluminium alloys (AA), a critical step is quenching from the solutionizing temperature. High cooling rates are desired, as they avoid formation of coarse precipitates, which reduce mechanical properties. Fast quenching, however, cannot be achieved in the centre of thick components, where the quenching rate can be more than one order of magnitude lower than at the surface. The existence of a thermal gradient between core and surface leads to a differential thermal deformation which is accommodated by elastic and plastic deformation to comply with the compatibility of deformation. Whenever the material yields, especially at high temperature when the yield strength is low, residual stress remains after quenching due to the irreversibility of plastic deformation. After quenching, the plates are in a state of residual stress that causes unacceptable distortions during machining and may reduce service life drastically. Since stress relaxation is negligible during ageing treatments [1 ], agehardened aluminium parts are usually stress relieved prior to ageing. This is typically achieved by applying plastic deformation: stretching from 1.5 to 3 % in the rolling direction (L) can reduce the internal stresses by a factor of approximately 10 [2, 3]. However, complex geometries or thicker components like thick sheets require other approaches. Reducing the quenching rate by using boiling water for instance leads to lower residual stresses [1, 4]."

Jan 1, 2013

By Peter Willbrandt

The flash smelter at NA was commissioned in March 1972 with an initial throughput of 50 tons of dry copper concentrate per hour. As a result of various measures, for example, oxygen enriched process wind, extension of the radiation part of the waste heat boiler, etc., the throughput could be increased to the present 70 tons per hour of dry concentrate. NA's plant is located on the outskirts of the city of Hamburg. The flash smelter's location and the growing awareness of the German population as regards environmental issues necessitate again and again considerable capital expenditure being spent on environmental protection. Thanks to the numerous small and large measures taken to protect the environment the emissions of dust, heavy metals such as arsenic, copper, lead, etc., and as well SO, could be drastically reduced. This paper will be giving an overview on the present state of the flash smelting process and the impact of the increasing environmental awareness at NA.

Jan 1, 1993

By Donna M. Noel

Bacterial strains have been cultivated from solids previously exposed to cyanide that will tolerate 300 ppm sodium cyanide under anaerobic conditions. In selected solid samples, these bacteria have been shown to reduce the level of cyanide from approximately 300 ppm to essentially zero in about 50 days under anaerobic conditions. Various media were investigated, and the nutrients providing maximal growth were ?established .. Degradation of cyanide in sterilized solids was determined for comparison with degradation obtained in bioactive solids. All experiments were conducted at ambient temperature and initial pH of approximately 10.5.

Jan 1, 1991

By F. Qian

An impinging gas jet on a liquid surface is found in many industrial process systems such as electric arc furnace, welding, steel-making operation and others. Fundamental understanding of the interaction of a gas jet on a liquid pool can provide important insights into process behavior resulting in improved efficiency. A numerical model is developed for solving the flow fields of both impinging gas jet region and liquid pool below, in which the deformed interface shape is predicted simultaneously. Using curvilinear coordinates, the Navier-Stokes equations of each phase are solved separately through coupling of static pressure, shear stress and velocity at the interface. Several cases for jet distances and flowrates were investigated both numerically and experimentally with an air-water model. Favorable comparison of numerical results with experimental data confirms the validity of the present numerical approach. An existing phenomenological model for 'penetration depth' prediction was extended for smaller 3et exit height to jet diameter' ratios.

Jan 1, 1995

By Eugene Jak

Copper sulphide processing technologies face increasing pressures associated with decreasing concentrate grade leading to increasing thermal inefficiency and lower productivity. Impurity concentrations are on average increasing, creating potential environmental risk and additional treatment costs. In copper flash smelters dust, partially oxidised materials and fume formed from the condensation of volatile impurities, are routinely recycled to the feed. In the converting stage the heat balance is maintained by charging anode reverts and other inert materials. In both cases, the thermal energy available from sulphide oxidation is not fully utilised or optimised. The productivities of both smelter and converter stages can be potentially increased through the addition of a high copper, low iron, low impurity precipitated copper product. Calculations are carried out for fayalite smelter and calcium ferrite converter slags using an optimised FactSage thermodynamic database. The potential for significant increases in smelter and converter productivities using existing technologies are predicted.

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Nozomu Hasegawa

The phase diagrams and microstructures of the slags in the Mitsubishi Continuous Copper Smelting and Converting Process were studied for the prevention of the magnetite troubles such as accretion build-up on furnace hearths and launders, blockages at the melt outlet, slag viscosity increases and so on. According to the results of those studies, the silica and lime contents in the silicate slag at the smelting furnace, and the lime content in the lime-ferrite slag at the converting furnace were changed, resulting in lower and more consistent copper levels in the discard slag, with much less need for operators to clean melt outlets and launders. However, these changes may decrease the desirable amount of accretion-coating inside the furnaces and thereby reduce furnace campaign lives. Therefore, a method of estimating the magnetite level in the melts was developed, and slag compositions and temperatures have been controlled within the appropriate ranges to prolong furnace lives and also prevent magnetite troubles.

Jan 1, 2003

By D. Quattrini

The aim of the present work is to present the gas chromatography (GC) as an alternative method of analysis in the thermal decomposition of calcium carbonate. Therefore, a furnace/GC on-line system was employed to study the kinetics of the reaction, measuring the CO2 produced in the decomposition. One of the advantages of the GC method is the possibility to perform an in-situ characterization and quantification of the gaseous products to obtain kinetic parameters, besides the method is simple and shows a good reproducibility. The decomposition of calcium carbonate was carried out in isothermal conditions at temperatures from 655 to 715°C with nitrogen as purge gas. Several gas velocities were used to determine the adequate flow that minimizes the effect of external mass diffusion as rate controlling step. It was made a preliminary analysis of the sample size influence on the reaction rate. The activation energy of the reaction was determined by Flynn method. The value obtained was in a good agreement with other authors. On the other hand, gravimetric measurements were employed for compare GC results.

Jan 1, 2006

By D. W. Collins

The uptake of gold from halide solutions by activated carbon has been investigated using various techniques. Halide systems typically exhibit combined adsorption-reduction type behavior. In an attempt to gain more information about the nature of these processes, samples of synthetic highly-oriented pyrolytic graphite (HOPG) were contacted with aqueous solutions of gold-iodide. HOPG represents a model structure for activated carbon comprising of basal- plane sites, edge sites, and various defect sites. Two basic instrumental methods were used to examine the uptake of gold by HOPG. The first was standard X-ray photoelectron spectroscopy (XPS). The other involved several scanning probe techniques. XPS clearly indicated a preferred uptake of gold at edge sites. However, iodine appeared to be distributed on both basal-plane and edge sites. At low iodine additions, tapping mode AFM showed that clusters were concentrated along steps and surface defects. At high iodine concentrations, the HOPG surface was uniformly covered by iodine.

Jan 1, 1998

By Chai Liyuan

This paper focused on the preparation of porous ceramic pellets for microorganism carriers. A new method for the process was developed using simple gel-casting and bubble-in-water-in-oil type of multiphase double emulsion. The globules, consisting of a foamed sepiolite slurry suspension, were dispersed and consolidated in spherical shape in liquid paraffin as gelation progressed. The green pellets were sintered at 1100°C. The influence of surfactants, extension ratio and impeller revolution rate on the process and characteristics of the pellets was investigated. The pellet size was in the range of 1~4mm and determined directly by impeller revolution rate. The fine cell diameter of porous ceramic was in the range of 100~500m and the micropore diameter was less than 5m. The inner macropores were interconnected and extend to the external surface. It is impossible to analyze a result by SEM micrographs and digital camera.

Jan 1, 2006

By Tangstadm Merete, Eli Ringdalen

"This paper presents an overview of results from The Norwegian Research Institution SINTEF and the Norwegian University of Science and Technology, NTNU regarding new and ongoing research in silicon production. The main studies are related to condensation of SiO gas and cavity formation. If SiO gas condensation is increased at the top of the furnace resulting in SiO content in the off-gas closer to equilibrium, the Si yield will be increased significantly. Experimental work, simulating a cavity under industrial conditions, has shown that the cavity grows downwards from one layer. Physical appearance of zones in industrial furnaces, and selected reactions in these, are discussed based on results from excavation of industrial furnaces and results from laboratory experiments. Experimental studies of reaction rates for the formation of SiO are presented. Quartz properties are demonstrated to vary between differing quartz types and the effect of this is discussed.Introduction Both the theoretical and industrial issues associated with the production of silicon are described in detail in the textbook written by Schei et al [1]. This book covers the knowledge of silicon production process up to 1998. Together with the work by Myrhaug [1] and by Aasly[2], this is the main basis for this paper. Recent and ongoing research at SINTEF and NTNU focusing on production of Si and SiO in the high temperature zone, dissociation of SiO and condensate and cavity formation will be discussed."

Jan 1, 2012

New method for processing of copper and nickel production feed has been developed and tested at pilot unit having 10 t/hr capacity. The process allows single-stage treatment of ore feed including that with high magnesium oxide content and resulting in the production of rich matte, high-grade matte, or moralised alloy for further leaching, as well as dump slag and off-gasses suitable for production of elemental sulphur, liquid sulphur dioxide, or sulphuric acid. Tests results and principal technical and economical parameters are presented.

Jan 1, 2006

By Rafael Padilla

The recovery of copper from chalcopyrite concentrates by leaching is difficult due to the slow dissolution kinetics of this mineral in most leaching media. However, recovery of copper from sulfidized chalcopyrite (a mixture of CuS and FeS2) by leaching is faster and could be selective depending on the leaching media. In this paper, the result of an investigation on the H2SO4-O2 pressure leaching of sulfidized chalcopyrite is presented. The variables considered in the study were stirring speed, concentration of sulfuric acid, temperature, and partial pressure of oxygen. The experimental data indicated that stirring speed over 500 rpm and sulfuric acid concentration over 0.1 M had very little effect on the leaching rate. An increase in temperature from 90 to 100 ºC increased both copper and iron dissolution; however, further increase to 120 ºC affected negatively the copper dissolution. Oxygen partial pressure was found to be the main variable that controls the copper/iron selectivity of the leaching. An increase in oxygen partial pressure increased significantly the rate of copper dissolution but deteriorated the copper/iron selectivity. The analysis for sulfur of the leaching solid residues indicated that most of the copper sulfide sulfur in the sulfidized concentrate oxidized to elemental sulfur.

Jan 1, 2006

By Tatsuo Inoue, Marnoru Mizuno, Toru Matsuoka, Kenichiro Abe

"The distribution of particle reinforcements and the residual stresses in metal matrix composite are simulated by considering the motion of particles and the solidification of matrix associated with temperature variation in the course of centrifugal casting process. In the analysis, a heat conduction equation including heat generation due to latent heat and also mechanical work as well as heat input from successively accumulated element on the air/metal boundary is solved by the finite element technique. After the movement of particles subjected to the centrifugal force and drag are analyzed, the residual stresses are elucidated by using a unified constitutive equation which can describe the behavior both in liquid and solid states. Results of the simulation are compared with the experimental data, and the validity and utility of the procedure is confirmed.IntroductionProcess simulation of metal matrix composite (MMC) is required to determine the mechanical properties of the materials and the efficient process and conditions of the fabrication. Properties of bonding matrix with reinforcements in the course of the processing, for example, affects the strength of the composite, while the final costs of the productions depends on the efficiency of fabrication. Therefore, the simulation of processing of MMC is prerequisite in order to clarify the mechanism to fabricate the material which has been expected to maintain high mechanical properties and the cost performance.Some techniques of processing MMC[l] have been developed so far. Among them, the centrifugal casting technique [2-5] has many attractive characteristics as processing of the MMC: The centrifugal casting technique makes the reinforcements such as particles or short fibers to be distributed in the radial direction by the centrifugal force acting on reinforcements due to the difference in density between reinforcements and matrix. Since the distribution of reinforcements affect the mechanical properties of MMC, the composite with functionally gradient mechanical properties can be provided by the centrifugal casting technique."

Jan 1, 1994

By Dengfu Chen, Huabiao Chen, Yunwei Huang, Mujun Long, Youguang Ma, Lintao Gui

In the current work, a three-dimensional model coupling turbulent flow, heat and solute transport was developed to investigate the solute transport and redistribution in the mold of slab continuous casting where the Reynolds number is very high and the molten steel flows strongly. The conservation equations of momentum, energy and species for a multicomponent system which includes solute element C, Si, Mn, P, S were solved with the commercial software ANSYS Fluent. The parameters used in the model are based on the actual continuous casting. The fluid flow, temperature distribution and solute elements distribution were analyzed. Results showed that negative segregation occurred near the strand surface, and the species concentration reached a peak value at the solidification front during solidification. The segregation degree of solute element S is higher than the other solute elements because of its lower equilibrium partition coefficient. The species concentration in the liquid pool is homogeneous because of the turbulent flow effect.

Jan 1, 2015

By Volker Uhlenwinkel

The design of a free fall atomizer as well as the process parameters affect the particle mass flux distribution in the spray cone. The mass flux distribution is important in spray forming because of its influence on the deposit shape and enthalpy input into the deposit. In this article the effect of different process parameters on the mass flux distribution is shown. Furthermore, different melts were atomized with the same atomizer. An empirical correlation will be introduced to predict the mass flux in the spray cone. This correlation will be compared with experimental results.

Jan 1, 1999

By Aichun Zhao, Rui Wang, Yihong Li, Yanping Bao, Yafeng Ji, Jiansheng Liu, Xiao Hu, Qingxue Huang

The slag entrapment under different conditions of 80t blowing argon ladle furnace was investigated by physical simulation. The water was used to simulate liquid steel and liquid paraffin was for slag. The processing of slag entrapment under different blowing structures was analyzed and the critical velocity and critical droplets diameter of describing it was obtained. Based on the experiments, the relationship between the interface flow velocity and the critical blowing rate CBR was deduced. In the real process, it is suggested that the bottom blowing rate is from 40 L/min to 180L/min when the interface tension is 0.12~1.2 N/m during the soft argon blowing.

Jan 1, 2016

By Entov Vladimir M., Gilmer R. Burgos, Andreas N. Alexandrou

"Processing of metal alloys in their mushy state represents a new trend in metal processing. As part of this process, known also as thixocasting, a specially prepared slurry at a temperature in the mushy region is injected into a die. Parts produced using this technology offer better mechanical properties than those produced by casting, and comparable to those of forged alloys.In thixocasting, semisolid slurries are highly concentrated suspensions of rounded rosette-like crystals in eutectic liquid. The mechanical behavior of the slurry is determined by the structure and properties of the skeleton formed by the alpha phase particles. The skeleton structure is almost never at equilibrium, and its evolution is, governed by a number of kinetic phenomena of different c11'aracteristic time-scales. Therefore, the skeleton structure depends on the mechanical and thermal history of the material. As a result of these kinetic processes, the rheological properties of the material, such as effective viscosity and yield stress, decrease with structure breakdown, and increase with its development. In the present investigation, the behavior of semisolid slurries during processing is modeled using the conservation equations, and a Herschel-Bulkley fluid model. The rheological parameters are assumed to be functions of the solid volume fraction, and of a structural parameter that changes with processing history. The evolution of the structural parameter is described by a first order kinetic differential equation that relates the rate of build-up and break-down of the solid"

Jan 1, 2000