Search Documents

By S. Kurama

Incorporation of de-watering sieve waste of borax (TSW) from Etibor Kirka Borax Company (Turkey) on the mechanical and physical properties of a commercial floor tile composition was investigated. In order to achieve this aim, TSW was partially employed in place of feldspar in the standard composition up to 20 wt %. The formulated compositions were wet milled, dried, shaped and then fired at 1190C for a total firing time of 38 minutes (from cold to cold) under industrial conditions. It was found that using of TSW up to 15 wt % improved the physical and mechanical properties of final product. The results indicated a good prospect for TSW as a co-flux in floor tile formulations.

Jan 1, 2006

By Leonardo Mota, Lucas L. da Costa, Milton B. Filho, Sergio N. Monteiro, Helion Vargas, Tammy G. R. Portela da Silva

"A natural biofoam extracted from the buriti palm tree has shown characteristics for potential substitution of synthetic foams. In the present work, a photoacoustic thermal characterization was performed on buriti biofoam samples. An open photoacoustic cell technique and a photothermal rise method performed under continuous laser illumination were employed in order to determine the thermal diffusivity and the specific heat capacity of such material. In addition to their intrinsic values (finger print), these physical parameters represent the light-into-heat conversion efficiency and the amount of heat stored per unit volume, respectively. The results showed that the buriti biofoam presents thermal properties that permit its use as an effective insulation material.IntroductionSolid foams are very light materials with increasing engineering applications [1]. A natural biofoam obtained from the petiole of the buriti palm tree (Mauritia flexuosa) has been recently investigated [2-4]. The evaluation of the buriti biofoam properties and the characterization of its microstructural aspects have shown that this biofoam has a potential as a new engineering material with very low density. Additionally, its reduced open porosity and low absorbed humidity revealed a promising material for packing and floating applications. In fact, this buriti biofoam, extracted from the palm tree natural of the north region of Brazil, is being used by the low income population as a modest substitute for Styrofoam® [1].As a potential insulating material, the buriti foam needs to be characterized in terms of its thermal and acoustic properties. A preliminary investigation [3] on the thermal behavior of this natural biofoam by thermogravimetric analysis, TGA, and its derivative, DTG, as well as differential scanning calorimetry, DSC, revealed parametric conditions associated with water loss and structural decomposition. Both the surface humidity and the release of hydration water were determined. Different decomposition events were attributed to both, more rigid as well as to more flexible molecular segments. Table 1 depicts technical data obtained so far for the buriti biofoam. These data are compared to those corresponding to Styrofoam®."

Jan 1, 2011

By Rauf Hurman Eric

The high temperature liquid miscibility gap in the Ag-Ag2S pseudobinary portion of the Ag-S system has been redetermined by very carefully conducted equilibration-quenching experiments. Samples were contained in evacuated and sealed silica capsules. The stratified liquid phase compositions were obtained by chemical analysis. The miscibility gap extends from 14 to 32.3 atomic percent at the monotectic temperature of 906°C and closes at around 1320°C.Thermodynamic properties of the liquid solutions, including the limiting activity coefficient of sulfur in molten silver were expressed analytically by using the sub-regular solution model which proved to be in excellent agreement with the experimental findings.

Jan 1, 2006

By G. Djambazov, D. Shevchenko, D. Burnard, V. Bojarevics, K. A. Pericleous, W. Griffiths

Contactless ultrasound treatment can be useful for high-temperature or reactive alloys in the liquid state, where contact with an immersed vibrating probe is undesirable. The alternating component of the Lorentz force can generate sound pressure levels leading to cavitation of gas bubbles in the melt, through acoustic resonance. Resonance is a function of the speed of sound in the liquid, the shape of the volume containing it and surrounding boundary conditions. Induction forces applied to a crucible lead to bulk stirring and in general deform the free surface, whose precise shape may influence the resonance conditions. This effect is investigated here b ymulti-physics computer modelling. Calculated results for aluminium melts are compared with experimental data and conclusions are drawn as to the sensitivity to process parameters and the reliability of this type of ultrasound metal processing.

Mar 1, 2017

By J. Chen Kuriyama

One method to store hydrogen effectively involves the use of metal complexes such as the alkali-element aluminum hydrides. The hydriding/dehydriding properties of these materials depend on how to prepare them with different structures and microstructures. The present work focused on a high-energy ball milling technique to produce Ti-doped lithium tetrahydridoaluminate (LiA1H4) and lithium hexahydroalanate (Li3AIH6) powders with nanocrystallites. The phase structures and dehydriding/rehydriding characteristics were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller measurement, thermogravimetry, and differential scanning calorimetry. The mechanism of dehydrogenation and rehydrogenation was also examined by means of X-ray photoelectron spectroscopy (XPS). The results on the relation between the reversible hydrogen storage and catalysis function of the Ti-doped complex hydride indicate that both the homogenous distribution of Ti+AI nanoclusters and the Ti¬catalyst with Ti e> Ti3+ (Ti0/Ti2+/Ti3+) defect sites play important roles in optimizing the reversible hydrogen storage.

Jan 1, 2002

By S. P. Song

A computational methodology based on the coupled finite element and boundary methods is developed to predict the free surface shapes of electrically conducting liquids supported by the electromagnetic field. The work is an extension of our previous FEIBE model for induction calculations. The free surface algorithm is developed using the Weighted Residual Method, the very same used for nonlinear finite element formulation. This allows the treatment of field computation and free surface prediction in the same manner, thus making easier the formulation of the magnetically-supported free surface problems. Like other nonlinear algorithms, the boundary/finite element free surface scheme is also iterative owing to the fact that free surface shapes are unknown a priori. But the numerical scheme is robust and efficient and is capable of handling rather complex free surface deformations. Computational algorithms will be given and are tested by comparing with other solutions whenever available. Computed results of magnetically-supported free surface shapes are presented for magnetic levitation under microgravity and floating zone refining processes under normal gravity.

Jan 1, 1996

By John J. J. Chen, Barry J. Welch

"The production of primary aluminium can potentially lead to metal that, with minimum treatment, meets a high purity standard. Smelters that can achieve a significant proportion of their production in this manner have a competitive edge which is of growing importance as the use grows for such items as compact discs and the like. Superimposed on the desire to produce high quality metal are stringent environmental requirements that the industry must adhere to. The environmental legislation focuses on fluoride emissions and the approach adopted is towards a zero waste management philosophy. The fluoride recycling process does, however, result in volatile impurities being captured and recycled to the cell. Aluminium has an extremely high reduction potential and this results in a significant proportion of the recycled impurities being reduced at the electrolyte metal interface and thus contaminating the metal. This paper reviews sources of impurities and the impact of the operating procedures adopted on metal treatment.IntroductionSeveral factors have contributed to the immense growth in the aluminium smelting industry. Initially the ready availability of hydro electricity provided a primary reduction energy source for the production of the light-weight metal. Because of its unique properties and innovation in the industry there has been a continued exploitation of its unique properties, especially at the high purity end of the metal. The industry has shown considerably versatility and innovation in adapting to the ever increasing demands of quality and purity. It is however a competitive industry and the ability to produce high purity grade metal (>99.9% pure) gives a competitive edge. Emerging markets such as for CD ROM disc production etc, will keep the quality demand stringent.While the industry has met the continuing demands for metal quality, it has also had to respond to stringent environmental requirements for emissions from the production plant. Like all extractive metallurgical processes carbon dioxide is an inevitable reaction byproduct. However, the volatilization and hydrolysis of the solvent electrolyte leads to fluoride emissions that are potentially harmful. Accordingly, the industry has adopted essentially a zero non-process waste management approach. All cell emissions, including reducible impurities, are recycled back to the cell. This has had a significant influence on the metal treatment processes."

Jan 1, 1996

By Jianxun Song, Hongmin Zhu, Qiuyu Wang, Jungang Hou, Shuqiang Jiao, Xiaobo Zhu

This work presents the results of a study on the Ti3+/Ti2+ couple redox potentials vs. Cl–/Cl2 at the temperature range (673 to 1073 K) in fused LiCl-KCl eutectic by direct potentiometric method. Initial concentrations of TiClx in solvents did not exceed 5.0 mol%. Basic thermodynamic properties of the reactions TiCl2+1/2Cl2(g)=TiCl3 were calculated using the temperature dependencies of apparent standard potentials of the couples E* Ti3+ /Ti2+.

Jan 1, 2014

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3-PbZrO3-Pb(Mg1/3Nb2/3)O3) system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densifieation by the normal sintering was slow even at high temperatures. When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.

Jan 1, 2003

By Gustavo Díaz, Miguel A. García, Carlos Frías

"Under the auspices of the Commission of the European Union, a consortium composed of six European organi~ations has conducted a project to scale up the PLACID electrowinning cell to industrial size within the Placid process development. This paper is concerning the results and achievement of the industrial cell prototype after more than 1,000 hours operating time and about 10,000 Kg electrolytic lead production. In general, results have been very satisfactory, demonstrating the ability ofthe PLACID electrowinning cell to produce top quality electrolytic lead (> 99.99 %) with high current efficiency and low energy consumption.IntroductionThis paper is concerning the development of an industrial size PLACID electrowinning cell within the PLACID process development. This project began on January 1993 and was finished on April 1996.Lead metal production and manufacturing industries produce large amounts of dusts and also lead bearing slags. Spent lead-acid battery recycling also produces lead oxides from the battery pastes rather similar to those mentioned above. Those lead secondary materials are hazardous and difficult to handle by usual procedures.Existing processes to treat-lead oxides may inflict considerable damage on the environment, incur high operating costs and have limitations to produce top quality lead.The main aim of this project has been to develop a novel hydrometallurgical process able to deal with different lead bearing materials, mainly lead oxide secondaries: lead-acid battery pastes, lead fumes, furnace slags, oxide residues, etc., producing ""four nines"" pure lead in an efficient manner with a benign influence on the environment; it is called the PLACID process."

Jan 1, 1997

By Neale R. Neelameggham, Ganesan Subramanian

Anthropogenic Heat Flux (AHF) is defined as heat generated from use of non-renewable energy by humans in residential, commercial and industrial activity. State of the art Global Circulation Models (GCM) used to predict global impacts of climate change to help set related policy do not include this heat flux. AHF is considered to be a much smaller an insignificant forcing, solely based on the global mean values. Various Climate models have discussed the “Heat Island Effect ” in high AHF areas. Through the use of simple climate models, it is shown that significant pockets of AHF can impact climate locally in ways significant enough to impact global climate. Inclusion of spatial AHF distribution, rather than a global mean value is important to accurate modeling either on a regional or global scale.

Mar 1, 2017

By Sadegh Safarzadeh, Anne-Marie Suriano, Stanley Howard

The electrodeposition of metal ions from aqueous electrolyte solutions has been a well-known process for the last half century. With numerous industrial applications such as electroplating, electrowinning and electrorefining, the kinetics of electrochemical reactions involved in the process has been extensively researched. Arrhenius-type rate equations, the Butler-Volmer equation, and the empirical Tafel equation are among the most important models to explain the rate of electrochemical reactions. The study of the kinetics of metal deposition is critical to understanding the underlying mechanisms through which a certain morphology of metal deposit is formed on the cathode. The purpose of this paper is to elucidate the influence of experimental parameters such as pH and additives on the rate and the reaction mechanism determining the rate limiting step of the electrodeposition reactions.

Jan 1, 2015

By Animesh Jha

The carbothermic reduction of chalcopyrite has been studied in the temperature range 1073 to 1273K in presence of lime. The role of lime during the reduction process is explained and the phase equilibria leading to the metallisation of copper and iron are discussed. The effect of coal and carbon monoxide on the reduction process have been studied and the rate governing steps are identified. This investigation also cites examples of possible mechanisms of physical separation of metallic Cu from iron during the reduction process.

Jan 1, 1992

By Jürgen Antrekowitsch

Typical zinc oxides recovered from wastes like steel mill dusts and neutral leaching residues are of a low quality because of impurities like fluorine, chlorine, lead and others. Therefore, they are not comparable to technical grade zinc oxides produced in “French” or “American Process”. Some new developments, most of them still in pilot scale, try to establish processes where higher qualities of the product should be achieved. Zinc oxides are not only supposed to be an input material for electrolytic zinc production. Far more, they should find their way into the zinc oxide market as a substitute for technical grade zinc oxides. Furthermore, a new field of application for these oxides has been investigated at the department of Nonferrous Metallurgy, University of Leoben. Because of a higher acceptance concerning different impurities in relation to zinc winning electrolyses, a use in electrolytic galvanizing shows an interesting option. Therefore, synthetic zinc oxides with different impurities were generated to study the effect of these impurities especially on the quality of the zinc layer. Typical steel sheets, as used for car bodies, were electrolytically galvanized and the resulting layer was analysed, as main impurities compounds of fluorine, chlorine, iron, lead and calcium were used for the investigations. Beside the layer quality, the current efficiency and the possible galvanizing speed were examined. The results give an indication, weather such an alternative application can be feasible from a technical and economical point of view or not. 597

Jan 1, 2008

By Yuanbo Zhang, Xiaoming Mao, Zhixiong You, Zhenyu Fan, Tao Jiang

"It is generally known that the formation of calcium ferrite is favorable during the iron ore sintering, which dominatingly contributes to the improvement of strength and reducibility of the finished sinters. In this study, effects of roasting temperature and 02 content of inlet gas on the sintering mineralization properties of typical iron ores, including hematite, limonite, specularite and magnetite, were investigated. The results showed the amount of calcium ferrite initially increased then decreased with the increase of the roasting temperature. The temperature of maximum calcium ferrite generation amount for different iron ores was determined as follows: hematite and limonite was 1275 °C, whereas specularite and magnetite was 1250 °C. Increasing 02 content of inlet gas was advantageous to the generation of calcium ferrite during the sintering. The sequence of 02 content affecting the mineralization properties of different iron ores was determined as follows: magnetite > hematite > specularite > limonite.IntroductionThe mineralization property of iron ore plays a significant role in the mineral composition and microstructure of finished sinters, which determine the quality and output of the sinters [1-2]. The mineralization process of sinters is composed of solid-phase reaction, formation of liquid-phase and crystallization. The formation and crystallization of liquid-phase is the foundation to the mineralization as the quality of the sinter is poor when concreted by solid-phase consolidation [3-4]. With respect to the iron ore sintering, liquid-phase regarded as bonding phase is generated between the iron ores and fluxes at high temperature [5]. Calcium ferrite is the most favorable liquid-phase among the bonding phases which dominatingly contributes to the improvement of strength and reducibility of the finished sinters [6-8]. Especially for high iron-low silicon sintering and high basicity sintering, making sure sufficient calcium ferrite quantity and reasonable distribution is crucial to the sinters [9-10]. Therefore, carrying out the researches on the high temperature reaction properties of iron ores is of great significance [11]."

Jan 1, 2013

By W. G. Davenport

The Cu content of industrial flash furnace concentrates varies considerably. It is usually around 30% Cu (Tables 2.1, 3.1) but it may be as high as 55% Cu and as low as 20% Cu. The mineralogy of flash furnace concentrates also varies. The most common Cu mineral is chalcopyrite (CuFeSz), but many concentrates contain bornite (CuSFeS4), chalcocite (CU2S), covellite (CuS) and even native copper (CUO). Pyrite (FeSz) :is also present in many concentrates. This chapter examines how concentrate composition affects flash smelting -with specific reference to 'low-Cu-grade' FeS2-CuFeSz concentrates. Chapter 14 does the same with 'high-Cu-grade' CuzS-CuFeSz?concentrates.

Jan 1, 2001

By Nils Lippmann, Ulrich Weber, Siegfried Schmauder, Jr. Mishnaevsky

"A computational approach to the optimization of fracture resistance of multiphase materials (here - high speed steels) by varying their microstructure is presented. The main points of the optimization of steels are as follows: (1) development and verification of the model: numerical simulation of crack initiation and growth in real microstructures of steels, (2) computational experiment: simulation of crack growth in different idealized quasi-real microstructures and (3) the comparison of fracture resistances of different microstructures and the development of recommendations to the improvement of the fracture toughness of steels. Numerical simulations of crack growth in real microstructures of steels and different idealized carbide distributions are carried out. On the basis of the simulations, recommendations for the improvement of high speed steel microstructures are given. It is shown that the fracture resistance of the steels is much higher for the fine than for the coarse version of the same type of microstructures.IntroductionThe purpose of this work is to develop an approach to the optimal design of multiphase materials on the basis of numerical simulation of their behaviour under mechanical loading. We suggest here the following strategy:1. Collecting input data for the simulations: taking a micrograph of a microstructure, and determining mechanical properties and failure conditions of the material constituents [1, 2],2. Simulation techniques and assumptions are tested for a real microstructure of the material: crack growth in a real microstructure is simulated and then compared with the experimental data,3. Computational experiments: different microstructures of materials are tested in the numerical model under the same loading conditions. The calculated service properties of the different microstructures are compared, and recommendations are developed. As differentiated from the ""real"" experimental techniques, the computational experiment is much cheaper and not labor- and time-consuming."

Jan 1, 2001

Acid mine drainage containing heavy metal ions is a large environmental problem facing the mining and mineral processing industry. The femte coprecipitation is a novel technique for removing heavy metal ions from waste water, recently applied to acid mine drainage. The fenite precipitation is usually performed at high temperature and therefore if applied in conventional manner, it becomes uneconomical to treat large quantities of acid mine drainage. In this paper the ferrite precipitation at ambient temperature-is &died. The possible mechanism of ferrite formation is discussed Experimental results from Noranda Tailing and Berkeley Pit water treated by this process are presented.

Jan 1, 1994

By Leon E. Laforest

An early commitment by Kidd Creek Mines Ltd. (formerly Texasgulf Canada) to follow a stringent environmental control programme from the initial stages of design and development of its metallurgical facilities in Timmins, Ontario, has resulted in the on-going attainment of extremely low levels of industrial waste emissions. This paper outlines the monitoring programme initiated and maintained by the company's environmental control section. Comparative results of environmental sampling for the periods before and after the copper smelter start-up are highlighted.

Jan 1, 1983

By B. C. Jena

In a chromite smelting process for the production of high-carbon ferrochromium, the slag composition profoundly affects operating conditions and the economic performance of the process. For a Canadian chromite concentrate, optimum slag composition and operating temperature were determined by process simulation with a computer model, which is based on parameters, such as the minimisation of slag volume, liquidus temperature, electrical energy consumption and chromium losses. Chromium recoveries are identified for slag compositions spanning wide concentration ranges within the quaternary system MgO-AI2O3- SiO2-CaO. The simulated data are compared with the experimental results.

Jan 1, 1994