Search Documents

By Ronald Klepper

In hydrometallurgy, pure gases like oxygen and hydrogen are used for oxidation and reduction. The gases are expensive and therefore should be used efficiently. Non reacted gas can be recycled into the liquid. Historically vortex gassing has been used; Le. a mixing impeller close to the liquid surface entrains gas from the headspace into the liquid through a gas vortex. Novel and more efficient methods are surface gassing with up pumping impellers and self- inducing gassing impellers. These alternative impeller systems are well established and common in the chemical industry, but have not been used until recently in hydrometallurgy. Gassing impellers act as internal compressors and increase the interfacial surface for a much higher mass transfer compared to alternate methods mentioned. In the paper results from lab and pilot tests and data from operated plants will be presented. The reactions with gases normally take place under moderate to high pressure, therefore a safe enclosure with mechanical seals and the safety "philosophy" is important. Experienced life and replacement cycles will be reported.

Jan 1, 2000

By Peter A. Spencer

Bacterial oxidation technology has the ability to selectively attack sulphide minerals. Selectivity allows oxidation of more reactive minerals and the extraction of valuable metals while leaving the bulk of the sulphide component unreacted. Partial oxidation can be used on arsenopyrite to recover gold and for the leaching of base metals, such as copper and nickel, from pyritic ore and concentrate without generation of large quantities of acidic iron solution, which must be neutralized. Thus, rejection of pyrite during the oxidation process can considerably reduce treatment costs. Acid generation in tailings dams would be minimal, compared with most Thiobacillus cultures, as the optimum growth temperature of Bactechts culture is above ambient.

Jan 1, 1992

By D. A. R. Kay

Phase stability diagrams are used to predict the abilities of lanthanum and cerium oxides to desulfurize coal gasification products in the temperature range 800-1000 C. Results of desulfurization studies in laboratory fixed bed reactors illustrate the effects of i) sorbent preparation, ii) input gas quality and iii) temperature, on the desulfurization reaction. 2CeO(2-x)(s) + H2S(g) + (1-2x)H2 = Ce2O2S(s) + 2(1x)H2O(g) The results of desulfurization/oxidation regeneration cycles are also reported.

Jan 1, 1989

By Kurt Westerlund

Three. years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm /h at Boliden Ronnskar Sweden on a TBRC smelting palena (PbS). Operating experience from the Kivset flash WHB 11.900 nm /h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3 /h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Olli Järvinen

The capacity of the Outokumpu Pori refinery is today about 125 000 mt in 1998. The anode slime amount is about 700-800 mt. The copper is removed with pressure leaching. Selenium roasting is done with the gas roasting. The doré smelting in the furnace is done with the tilting rotating converter with oxy-fuel burner (TROP). Doré anodes are treated in the silver electrolysis. Gold is recovered from the gold mud with the quick hydrochloric acid leaching process. The important point in the leaching is to get into contact the solid copper with the oxygen and liquid. Outokumpu has an efficient agitator for this purpose. The GLS-agitator (GLS=gas, liquid and solid) is powerful for mixing oxygen, liquid and solid together. The current production in Pori plant is 40000 kg of silver, 5000 kg gold, 40000 kg of selenium and one hundred kilograms of platinum-palladium concentrate.

Jan 1, 2000

By Helena Byrdziak

KGHM Polska Miedz SA, in existence since nineteen seventies, operates three underground mines and three smelters with total production of over 400 000 mtpy of electrolytic copper. Its impact on the environment, very serious in the past, has been gradually reduced. While in general emissions into the air and water have been brought under control, attention recently has shifted to the disposal of wastes and residues. The main streams of wastes are flotation tailings, slags and dust captured from the dedusting systems. Much effort has already been expended and is still being spent to utilize this waste for by-products production or to dispose of it within the process by recycling. The most effective measures taken up thus far, as well as present activities directed at tailings disposal, are presented.

Jan 1, 1997

By Wang Dawan

During the process of arsenic bearing gold concentration biooxidation, the content of chloride ion in water is a very important factor to the activity of bacteria and the oxidation of sulfide minerals. In this paper, the influence of underground mine water with different chloride ion content to the biooxidation of arsenic bearing gold concentration and the limit of chloride ion content to bacteria were summarized. These results indicated if the content of chloride ion was less than 1.2g/L, the bacteria?s ability to oxidize sulfide minerals was little affected, and if the content of chloride ion were increased to 2g/L or more, the activity of bacteria was seriously restrained, and if the content of chloride ion were increased to 4g/L, the activity of bacteria was absolutely restrained. So, as the content of chloride ion in water was cumulated to 2g/L or more in biooxidation plant, the water must be refreshed to maintain normal production.

Jan 1, 2008

By Gui-fang ZHANG, Zhe SHI, Lei GAO

Secondary V-recycling slag, an industrial waste containing high gallium is being dumped continuously, which causes the loss of gallium. Thus, the alkali fusion process was employed to recover gallium from this slag. The effects factors on extraction of gallium such as roasting temperature, roasting time, alkali fusion agent concentration and CaO concentration were investigated in the paper. The experimental results indicated that excessive roasting temperature and roasting time is unfavorable to the recovery rate of gallium. The appropriate roasting temperature and duration are 1000 and 2 hours, respectively; The appropriate proportioning of Na2CO3: NaOH is 2:1 when the concentration of alkali fusion agent weighs 0.4 times the mass of the slag; In order to remove SiO2 from the leaching liquor, CaO should be used as an additive in the roasting process. The appropriate concentration of CaO should weigh 0.2 times the mass of the slag. Employing these optimal alkali fusion conditions in the roasting process, gallium recovery is above 90%

Jan 1, 2015

By Björn Lindquist

Boliden has developed a number of specialised technologies for smelter gas handling and effluent treatment. These technologies will be described. Special attention will be given to the high-pressure venturi, Editube wet electrostatic precipitator, mercury removal processes, and two-stage effluent treatment.

Jan 1, 2002

By Yuanbo Zhang, Yingming Chen, Zijian Su, Bingbing Liu, Jun Chen

Iron, tin-bearing tailings is a kind of hazardous solid waste generated from cassiterite dressing operation. It is difficult to utilize the tailings by present mineral processing methods due to the complex dissemination characteristics. In this study, a process of gas-based magnetizing roasting followed by magnetic separation was studied for separating and recovering iron from the tailings. The effects of roasting and magnetic separation parameters on the recovery of iron were systematically investigated. The optimum parameters were proposed as follows: CO/(CO+CO2) content of 5%, roasting temperature of 850 C, roasting time of 60 min, grinding particle size of 90% less than 45 μm and magnetic field intensity of 800 Gs. Under these conditions, the magnetic concentrate containing 68.5% Fe and 0.06% Sn was achieved, which can be used as high-quality raw materials for direct reduction iron production.

Jan 1, 2016

By KAGAN BENZESIK, Onuralp Yücel, Mehmet Bugdaycı, Ahmet Turan

ZrB2 and B4C are one of the most significant advanced ceramics. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: Self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, Carbon black, B2O3 were used as starting material to produce ZrB2-B4C powders by SHS. Also Mg powder was used as the reductant. The reaction mixtures (approximately 100 g) were mixed thoroughly 15 minutes in a turbula mixer and charged into Cu crucible and compacted. W (tungsten) wire was placed at the top of copper crucible and the reaction realized by passing current through the wire. After initiation, a highly exothermic reaction became in a self-sustaining mode and propagated throughout the SHS mixture. The samples were characterized by using AAS and X-Ray Diffraction.

Jan 1, 2016

By Jian-hua Ren, Guang-liang Wu

A lot of dust is produced in iron and steel enterprises, giving rise to serious environment pollution, with which all countries are trying to find methods to deal. The influence of relevant technological factors on dephosphorization was investigated in laboratory, and the effect laws of that were analyzed. The results demonstrate that, in the given conditions of the best slag-metal proportion for hot metal dephosphorization is 1:10, and the optimum temperature is 1350 , The phosphorus distribution ratio of dephosphorization agent containing converter dust of 30% has the maximal value, with dephosphorization rate reaching 85%. Under the optimal conditions, premelting dephosphorization agent can significantly improve the ability of dephosphorization, dephosphorization efficiency increasing to 92%. Therefore, the dust can substitute the oxidant and fixative of dephosphorization agent, be used in hot metal dephosphorization, to enhance the efficiency of utilization.

Jan 1, 2016

By Glenn Stevens

After 40 years of operation with the original design, Pan Pacific Copper determined it was necessary to rebuild the Saganoseki Flash Smelting Furnace to continue safe operation. The original design employed a rigid steel frame, which, through hearth growth, led to severe distortion of the frame. Contributing to the continued growth of the hearth were thermal cycles that occurred during the government mandated annual shutdowns. Hatch designed a unique sprung bound, pivoting binding frame to maximize crucible size within the existing furnace footprint, while integrating the PPC designed cooling jackets. The bound system maintains tight brick joints, while the new conductive hearth design with integrated bottom cooling produces a protective freeze layer to accommodate higher furnace throughput. Minimization of furnace downtime for the rebuild was achieved through effective construction planning, highly trained contractors, and through an efficient start-up and ramp-up to full production.

By Baohua Li, Yanhui Liu, Shengping Li, Xuewei Lv, Yun Chen

There are almost ten billion tons of vanadium-bearing titanomagnetite in Panzhihua-Xichang area. However, iron ores in Hongge, which has the most abundant reserves in the four mine areas in Panzhihua, have not been utilized sufficiently so far. The reason behind this is the relatively high Cr2O3 in the ores (0.49 %~0.82 %), that due to its high melting temperature will negatively influence the blast furnace reduction and slagging process. Therefore, in the blast furnace process, Cr is hope to be reduced into molten iron, which can reduce slag viscosity problems. Slag iron reduction experiments were conducted to quantify the Cr reduction. Experimental results shows that with the increase of TiO2, the content of Cr in the hot metal is decreased when balanced. And during the initial stage of the reduction reaction, the reaction kinetic model is a first-order reaction.

Jan 1, 2016

By Andre Thess, Oleg Zikanov

"Direct numerical simulation methods are applied to study the influence of a constant magnetic field on turbulent flows of liquid metals. The flow is assumed to be homogeneous and the problem is reduced to the classical case of the turbulent flow in a 3D box with periodic boundary conditions. The main subject of the study is the anisotropy developing in a liquid metal flow affected by constant magnetic field.To investigate the long-time evolution of initially isotropic flow the large-scale forcing is applied to maintain the flow energy at a statistically steady level. It is found that the flow evolution depend strongly on the magnetic interaction parameter (Stuart number). In the case of small Stuart number, the flow remains three-dimensional, turbulent, an approximately isotropic. At large Stuart number (strong magnetic field) the turbulence is suppressed rapidly and the flow becomes two-dimensional and laminar. Very interesting is the intermittent flow evolution at moderate Stuart number. Long periods of almost two-dimensional, laminar behavior are interrupted by strong turbulent three-dimensional bursts.The influence of a constant magnetic field on scalar transport properties of liquid metal turbulence is investigated using the simplified formulation of homogeneous flow driven by an imposed mean temperature gradient. Such a flow consists primarily of two turbulent antiparallel jets providing an effective mechanism for heat transfer. It is shown that the magnetic field parallel to the mean temperature gradient stabilizes the jets and, thus, enhances heat transfer considerably."

Jan 1, 1999

By Mark Cross, Hadi Abou-Chakra, Nicholas Christakis, Mayur K. Patel, John Baxter, Ugur Tiizful

"In recent years significant effort has been put into using continuum mechanics for the description of granular flows. Although these models are partially successful in capturing some flow characteristics, they lack essential information on material properties, which are needed to account for the interactions between different particles. Thus, they are incomplete and can not be used to describe processes such as hopper filling/emptying and pneumatic conveying, where particle-particle interactions can lead to phenomena such as segregation, degradation and agglomeration. In this paper, a 3-D unstructured finite-volume framework is presented, which employs interface tracking techniques to solve for the individual material components of the granular mixture in the bulk and thus, determine the material-air interface. Various transport processes, arising from the micro-mechanical properties of the different particle species in the granular mixture, can be obtained through kinetic theory. The transport coefficients of each of the individual species can be determined and analysed in a micro-mechanical framework and the transport process parametrised in the form of constitutive models. These models provide the continuum theory with information on the micro-mechanics.This work describes the continuum framework and the micro-mechanical parametrisations, which are used to describe the processes and interactions at the microscopic level. Numerical simulations and comparisons with experimental data are then presented for the case of binary granular mixtures and conclusions are drawn on the capability of the model to realistically predict and quantify the main characteristics of granular flows."

Jan 1, 2001

By W. G. Davenport

Changes in copper extraction from 1960 till today are documented. The top ten changes have been: (a) replacement of reverberatory smelting by high intensity oxygen rich smelting (b) growth of the Outokumpu flash smelting to over 50% of the world's smelting capacity (c) successful development of single furnace coppermaking but only for low slag fall concentrates (d) replacement of the batch Peirce-Smith converter by continuous converting, but only in a few cases (e) increased SO2 capture throughout the industry, mainly-as sulfuric acid (f) development of low initiation temperature `big bight' Cs catalysts for treating the continuous high-SO2 strength gases from continuous smelting/converting (g) complete replacement of reverberatory anode scrap and cathode melting furnaces by the Asarco shaft furnace (h) adoption of stainless steel permanent cathodes and automated stripping technology for electrorefining and electrowinning (i) complete elimination of wire bar casting by continuous bar casting/rod rolling (j) development and adoption of extractants for turning weak impure leach solutions into strong pure electrolytes. It is postulated that the biggest possible change over the next 20 years would be complete replacement of smelting/converting by hydrometallurgical processing. However, this seems unlikely due to copper purity, precious metal recovery, and economic concerns. The increasing value of sulfuric acid to many copper companies gives chalcopyrite smelting/oxide-supergene leaching a nice synergy especially with the energy credits now coming from continuous smelters, and their acid plants.

Jan 1, 1999

By Jiakai Zhang

Many postconsumer electrical and electronic equipment wastes contain a considerable amount of rare earth elements (REEs); however, the current level of REE recycling from them is limited (<1%). Neodymium–iron–boron (NdFeB) magnets, used at both small- and large-scale, from computer hard disk drives and small tools to wind turbines and cars, are a good example of such waste materials that contain high content of neodymium (Nd) and dysprosium (Dy). These elements are considered critical metals because they are the main building block of emerging green technologies that will allow for GHG emission reductions. Because demand for these green products is increasing around the world, the demand for REEs is increasing quickly, putting their supply at risk in the near future. Thus, it is critical to develop efficient, robust, and cost-effective processes to recycle these elements from this class of electronic waste materials. Here, we performed a thorough characterization of a N52–NdFeB magnet to identify its composition, crystal structure, and morphology. Furthermore, we developed an efficient hydrometallurgical process to extract Nd and Dy with high efficiency (more than 95%).

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By Jafar Safarian

Bauxite is the main raw material used for the production of alumina (Al2O3) through the well-known commercial Bayer process. This process has significant challenges such as limitation in using low-grade bauxites as they contain significant amounts of impurities such as Fe, Si, Ti. The Bayer process residue, which is known as red mud, is also a global environmental challenge due to huge amount of this low value residue production. An alternative sustainable process with high potential to solve these problems and produce valuable and consumable by-products is a pyrometallurgical-hydrometallurgical process in which the low-grade bauxite ore is treated through a smelting-reduction process, yielding iron alloys and a calcium-aluminate slag. Alumina is then produced from the slag by hydrometallurgical treatment. In the present work, the reduction of pellets produced from different bauxite ores by hydrogen is studied and it is shown that complete iron oxides reduction is possible. Further smelting and smelting-aluminothermic reduction of the reduced pellets show that iron and silicon ferroalloys can be produced, in addition to a proper slag for alumina extraction.