Search Documents

By Jae-Chun Lee, Jinki Jeong, Manis Kumar Jha, Divika Gupta, Pankaj Kumar Choubey

Rare metal indium (In) is mostly used as electroluminescent material in liquid crystal displays (LCD) monitors. Present paper describes leaching studies for the recovery of In from waste LCD monitors in presence of different other impurities. The leaching studies showed that more than 85% of In was leached out using 20% sulfuric acid at 60oC in mixing time 30 min at fixed pulp density 25 g/L. The solution could be purified using SX/IX and from the pure solution metal/ salt could be produced by evaporation, precipitation, electrolysis, crystallization processes.

Jan 1, 2014

By V. Madhusudhan Rao

Fly ash is a finely divide non ? combustible material obtained as a by ? product of coal combustion. It is a major by ? product of coal based thermal power stations. Until recent past it was considered as a waste and highly polluting material. However its formation can only be minimized by using suitable technology in the boilers. In recent past it is found that Fly ash has many end uses and it has proven itself to be a potential construction material. But the suitability of fly ash for various applications largely depends on the amount of unburned carbon, which is turn depends on the firing method. Fly ash samples from various power plants existing in India using a fluidized bed method and pulverized bed were analyzed and a comparison of these two firing methods was carried. This paper deals with the compositional requirements for fly ash used for the fabrication of insulating doors using AAC (Aerated Autoclave Concrete) and the methods employed to make fly ash suitable for this purpose. It also includes the latest ?U? beam technology for effective fly ash recycle. If the by products of coal combustion from power plants like fly ash as the paper stresses are utilized properly, it is not an exaggeration to say that power generation is possible with absolutely zero cost.

Jan 1, 2006

By T. A. Venugopalan

The 'Hall-Heroult' Process of reduction of Alumina to Aluminium has remainded basically the same for over 100 years, but the technology has been undergoing drastic changes with respect to selection of materials for Cathode and Anode, and also energy consumption. The latest generation pots have a working life of about 1800-2000 days normally. After the failure of the pots, the Cathode Lining is dug out and disposed of on land. Since the lining contains objectional materials causing pollution, various processes have been tried for re-processing of this waste. However, most of the processes have been unsuccessful from the techno-economic point of view. At Hindalco a new chemical process for converting the fluorine values of the dug out material to Cryolite was developed in 1988 and a" one ton per day Cryolite production plant has been operating since 1989. This process is especially applicable where the integrated Alumina and Smelter Plants exist side by side. The experience in operating this Plant is discussed in detail in the paper.

Jan 1, 1992

By Yang Guangqing, Shao Jiugang, Zhang Jianliang, Wan Dan, Fu Yuandi, Guo Hongwei

"Resource of metallurgical coke is becoming scarce, and although coke can be partially replaced by pulverized coal injection, there are many restrictions for further increase in coal ratio. Mixed charge of ore and lump coal from top to replace more coke was studied in this paper. Softening-melting property of the burden was affected by charge of lump coal. Softening-melting properties of mixed charge of ore and coke, mixed charge of ore and lump coal were tested respectively. Results show: the property of the burden mixed with coke is superior to the burden mixed with lump coal; lump coal would not deteriorate softening-melting property of the burden and some of them can even improve softening-melting property of the burden. Top charge of lump coal would not deteriorate softening-melting process, and this should be a new way to increase coal consumption to decrease coke rate.IntroductionThe blast furnace is still the predominant process for the reduction of iron ore and will probably remain so for the next decades. Metallurgical coke is becoming scarce and expensive, so the cost of hot metal can be decreased by reducing the consumption of metallurgical coke[l]. Coke can be partially replaced by pulverized coal injection, currently the highest rate of pulverized coal reached 266kg/tHM, most of blast furnace PCR is about 150kg/tHM, and it is very difficult to further increase of PCR. Nut coke is charged into blast furnace mixed with iron ore, not only for improving utilization of metallurgical coke, but also for lowering the coke rate. Presently the majority of blast furnaces in the world use nut coke although its amount is very different: from 10-20 to 70--100 kg/tHM and more[2-4].The effect ofnut coke in blast furnace is extensively researched, and the main conclusions recommend: to improve gas permeability of cohesive layer in blast furnace, to promote reduction of iron burden, protect metallurgical coke from the solution in the shaft due to higher reactivity of nut coke. There is no special requirement for the strength of nut coke[5-8]. Nut coke is also used for sintering fuel, which may lead to the shortage of the nut coke charging into blast furnace. So lump coal mixed with iron ore is considered to be charged into the blast furnace, not only to reduce the cost of grinding coal, but also to increase the use amount of coal."

Jan 1, 2013

By Jan Smit

Sulphidic copper concentrates are generally processed by pyrometallurgical means; while oxidative pressure leach processing of such materials has been shown to be technically feasible, there has traditionally been little incentive to choose this route in favour of a smelting option. However, for concentrates with elevated arsenic levels, oxidative pressure leaching offers distinct advantages, as smelter air emission standards and restrictions on concentrate importation have tightened. The current state of pressure leach technology allows for high copper extractions from arsenical copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. In its studies on pressure leaching of copper concentrates, Sherritt has shown that arsenical feed materials can be converted into environmentally stable residues, with excellent copper extractions. The results of recent batch and pilot plant test work are discussed, including the deportments of copper, arsenic and precious metals.

By Patrick M. Eduafo, Brajendra Mishra, Mark L. Strauss

Direct acid leaching of rare earth metals (REMs) from waste lamp phosphors is non-selective, leading to co-dissolution of impurities mainly calcium, phosphorus, silicon, iron and zinc. Calcining the phosphor powder at different temperatures followed by leaching with HCl isn’t efficient for the extraction of all the chief rare earths especially cerium (Ce), lanthanum (La) and terbium (Tb). Therefore, multi-stage leaching operations are required for the separation of the REMs in phosphor dust. This paper will outline a new process for extracting Ce, La, Tb, Eu and Y from waste fluorescent lamps using a three-stage leaching and separation process. A flowsheet has been developed which shows this process is selective and efficient.

Jan 1, 2015

By Mitchell L. Spencer, Viswanathan Panchanathan

"Bonded magnets are important category in permanent magnets. They are made by one of the following processes: compression bonding, injection molding, extrusion, calendering. An overview of the various bonded magnet processes and properties of products made with different magnet materials along with their applications are discussed. The main emphasis will be on the use of bonded NdFeB and ferrite magnets.IntroductionBonded magnets are a major growth area in permanent magnets. Bonded magnets are made by any one of the following processes: Compression bonding; Injection Molding; Extrusion and Calendering [1,2]. Compression and injection molded magnets are rigid magnets. Materials used in calendering process produce flexible magnets. Only the extrusion process makes both rigid and flexible magnets. The binders used for the bonded magnets vary depending on the processes. Thermoset, thermo-plastic and elastomeric binders are respectively used in compression, injection and the calendering process. Extrusion molding uses elastomers or thermo-plastic materials. The most co=on magnetic materials, Ferrite, SmCo, Alnico and NdFeB can be used in any of the above processes either alone or in combination as hybrid magnets. Another material that has been developed for co=ercial application is SmFeN. Making the material has been challenging and it is being used in niche market applications in limited quantitiesIn the extrusion process, a highly loaded compound is used to produce strip or sheet and is continuously extruded through a die. In calendering the granulated compound is rolled to produce a continuous wide sheet. In the compression bonding process a uniaxial pressing force is used. These magnets have higher loading compared to injection molded magnets. In injection molding the material is forced into a mold cavity and has lower loading compared to compression molded magnets [2,3]. Most of the flexible magnets are made using extrusion and calendering processes and the most co=on magnet material is inexpensive ferrite. Flexible magnets have been made using rare earth materials, but on a very limited basis.The major advantages of magnets processed by extrusion and calendering are as follows: inexpensive tooling, automation; practically any 2D geometry; fast production rates; no chipping or breaking; a wide range of properties; on-line magnetization; easy to convert (e.g. cut, punch or shape).Compression bonded magnets are inexpensive to manufacture. They have higher magnetic properties compared to injection molded magnets; however lower than their sintered counterparts. The magnet shape is restricted to simple geometries and they require careful handling. Their isotropic nature allows complex magnetizing patterns."

Jan 1, 2013

By W. J. Guay

Scrubbing of simulated copper reverberatory furnace gases containing 1.0 percent sulfur dioxide with the minus 74 ~m fraction of the San Manuel tailings has shown sulfur dioxide removals of almost 100 percent over an effluent pH range of 3.1 to 4.6 and a wide range of liquid to gas ratios with absorptions of 11 to 17 Kg of sulfur dioxide per tonne of minus 74 um slimes. The high reactivity of the tailings slimes with S02 indicates that the reaction rate is not controlled by the slow dissolution of calcium carbonate in sulfurous acid which characterizes scrubbers using ground limestone. The interpretation of these results has been considerably enhanced by wet chemical analysis and emission spectrographic analysis which show that calcium and iron account for about 90 percent of the SO2 absorption with the rest being accounted for by aluminum, magnesium, potassium, and sodium. Mineralogic examination confirms the, chemical and spectrographic analyses showing that the major constituent removed from the slimes is calcium carbonate, with lesser amounts of chlorite and montmorillonite (silicates containing iron, magnesium, aluminum, and calcium) being removed.

Jan 1, 1981

By Roberto Parra

The wear and corrosion phenomena in the furnace lining of the ferrous and non ferrous pyrometallurgical processes are complex problems where chemical, interfacial and mechanical phenomena are presents. The characteristics of the processes determine the conditions to which these materials are submitted, where the thermal conditions reached during the operation is one of the most important parameter. Assuming that all the degradation phenomena are thermal activated, the rate of the different steps of the wear mechanism will depend on the thermal field in the lining. In view to apply the independent physicochemical knowledge of degradation mechanisms to the analysis and design of furnace lining the methodology of the Nodal Wear Model (NWM) was done. It combines the mathematical modelling of the heat transfer in the lining with the physicochemical control equation for the wear-corrosion phenomena. The NWM has been applied to different examples: theoretical analysis, laboratory scale test and industrial applications. We present in this paper the theoretical background of the model and two examples of applications: the sole of an electric furnace and the earth of a blast furnace.

Jan 1, 2006

By Sayan Sarkar

HAMR (Hydrogen Assisted Magnesiothermic Reduction) process is a promising alternative route of titanium production, which is convenient due to reduction at relatively lower temperatures below 750 °C and usage of cost-efficient TiO2 as the starting material. A crucial step involved in this process requires the Mg reduction of TiO2 subjected to H2 atmosphere which produces porous TiH2 along with residual magnesium impurities. Before the final heat treatment and deoxygenation steps for consolidation of the Ti powder, leaching plays a significant role in the removal of Mg impurities. In this report, we present a systematic study on the role of acid concentration (HCl), temperature and the kinetics of MgO dissolution. In addition, we also report the controlling mechanism during kinetics of MgO dissolution in acid. This parametric study will provide a platform to ensure very low Mg content that meets with ASTM standards during production of Ti in the HAMR process.

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The basics of microwave drying process of CuCl residue were studied by comparing the dielectric property of the residue with different moisture contents. The dielectric properties were measured by microwave cavity perturbation method. The dielectric constant and dielectric loss factor of the CuCl residue have a linear correlation with the moisture content. With this relationship, we can realize on-line measurement of moisture content of the CuCl residue by dielectric properties. The microwave drying experiments with different thicknesses (1-5cm) of CuCl residue were carried out, and the heating curve of the materials under different microwave powers (250-450W) was made. From these parameters, an optimized operation parameter of microwave roasting technology, the thickness of CuCl residue filter cake to be microwave roasted should be 2cm , was deduced.

Jan 1, 2015

By Ibrahim Yusufoglu, Ahmet Orkun Kalpakli, Cem Kahruman, Sedat Ilhan

"The effects of oxalic acid concentration, temperature, stirring rate and particle size on the dissolution rate of synthetically prepared calcium molybdate were investigated. Dissolution of calcium molybdate in oxalic acid solutions takes place as a series - parallel type reaction. In the first reaction step, which proceeds according to the ""Langmuir - Hinshelwood Mechanism"", calcium aqua oxalato molybdate is formed as a complex chelate intermediate product. In the second reaction step, molybdic acid is formed during the slow hydrolysis of calcium aqua oxalato molybdate, and it reacts rapidly with oxalic acid to form the polymeric hydrogen oxalate dimolybdate chelate as an end product. Activation energies were calculated as 41.4 and 49.9 kJ mol-1 for the first and zero order reactions. The fractional conversion versus time relationship can be given by the following equation.IntroductionMolybdenum is used widely in electric-electronic, metal working, aerospace and aeronautic, nuclear, glass and petrochemical industries because of its high melting temperature and resistance against chemical effects. However, the largest molybdenum consumers are the iron-steel and super alloy industries where molybdenum is used as an alloying element. Industrially important molybdenum minerals are limited to molybdenite (M0S2), powellite (CaMo04) and wulfenite (PbMo04), which are considered as primary molybdenum resources. Secondary molybdenum resources are spent catalysts and scrap [1-4].Molybdenum has been produced by pyrometallurgical processes in the past. Since it is possible to process low grade molybdenum ores and industrial wastes by hydrometallurgical processes, which are more environmentally friendly than pyrometallurgical processes, the importance of the use of hydrometallurgical processes has increased in the molybdenum production industry."

Jan 1, 2012

By Alexander I. Raitchenko

"An electroconductive viscous liquid may flow in laminar or turbulent regime under Lorentz-force generated by the intercrossed electric current and magnetic field. When there is a starting flat layer between hard and free boundaries with surface tension the spatial Lorentz-force can create a specific stationary regime of flow: the plane free surface will transform into the wavy one, and the movement in the depth will be not laminar and not turbulent, but this regime will be characterized by organized forms with indications of ""rolling of long cylindrical drops"". Wave-length is determined by the viscosity, the density, the surface tension, the average thickness of layer, and Lorentz-force. ·The limit of wavy regime is determined by most long of wave which is directly proportional to the critical value of specific flow and inversely proportional to the kinetic viscosity. The proper critical value of Reynolds number is determined by the dimensionless combination containing surface tension, density, viscosity, and Lorentz-force. The mentioned dimensio.nless combination in our case is some criterion substituting the known Kapitsa number for case of the thin viscous liquid layers under gravity. Spreading of admixture by mechanism of wavy regime is more rapid than by common diffusion or by laminar flow. The suggested conception can be a contribution into the theoretical basis for elaboration of some specific liquid metals technologies."

Jan 1, 1999

By Yuanbo Zhang, Zhixiong You, Zijian Su, Bingbing Liu, Guanghui Li, Guang Yang, Tao Jiang

Sodium stannate is widely used in the electroplating and tin alloy industry. But the traditional processes for sodium stannate production are characterized by long flowsheet, high production cost and strict requirement for the equipments, etc. In this study, a novel process for sodium stannate preparation from cassiterite concentrate and sodium carbonate via roasting in CO/CO2 mixed gas then followed by leaching was developed. The effects of roasting parameters on the Sn leaching efficiency were conducted. A Sn leaching efficiency of 77.2% was obtained under the optimal conditions. Sodium stannate (Na2SnO3·3H2O) with a purity of 95.8% was produced by the new process, which is better than that specified for the industrial first-grade product.

Jan 1, 2014

By Toshio Kurikami, Koichi Yamazaki

"Toho Zinc Co., Ltd Chigirishima Refinery has the production capacity of electrolytic lead for 95000t/y by sintering- blast furnace electrolytic process. Lead raw materials are lead concentrates, spent batteries and dusts that contain lead from other companies, and these are handled by existing smelting process. There are many circulation materials in the process, because the system has been constructed with improving the recovery rate and protecting the environment. This report describes material balance in each process, distribution of the lead and various components, and it examines present state of the processing. In addition, we report the result that we have tried to improve the work environment.IntroductionThe Chigirishima Refinery of the Toho Zinc Co., Ltd. is located in Chigirishima, an island 4km off the coast of Takehara-city, Hiroshima, Japan. The Chigirishima Refinery began lead smelting operations in 1951.The Chigirishima Refinery adopted the sintering-blast furnace-electrolytic process and has an electrolytic lead production capacity of 95,000 tons/year. The existing smelting process handles raw materials from lead concentrates, spent batteries, and lead-bearing dust from other companies. This system was constructed with the intentions of improving material recovery ratios and protecting the environment; therefore, there are many materials recirculating throughout the smelting process. This report describes the material balance in each process and the distribution ciflead and various components, and it examines the present state of processing. In addition, we report the results of our attempts to improve the work environment."

Jan 1, 2000

By C. B. Piazzarollo

Red Ceramic materials are widely used in Civil Construction in Tropical Countries. However, these materials have high porosity and low mechanical strength. Thus, in order to improve these properties, recycle mineral wastes was incorporated into clay from Campos - RJ, ornamental rock waste, from the gneisses cutting of Cachoeiro - ES, 150 km from Campos. After the addition of up 10% of waste in clay mass, ceramic pieces were produced and subjected to the tests of porosity (P) and flexural strength (FS). The test material contains 53.3% clay and 67% waste slit. The X-ray diffraction identified the presence of kaolinite, quartz and feldspar for the clay and, for the waste, quartz and orthoclase. The results of FS and P showed that the residue influenced, positively, the ceramic piece, with strength gains especially from 920º up to 960°C.

Jan 1, 2015

By Afshin Sadri

Acousto Ultrasonic-Echo (AU-E) is a technique developed to provide accurate measurements of the refractory lining wear in operating smelters based on the principles of stress wave propagation. The objective of the system is to provide feedback for the continuous optimization of the overall smelter operation. In some cases, the AU-E refractory lining measurements have allowed clients to extend their smelter campaigns and operate safely for several years beyond their planned reline schedule. In other cases, AU-E results inform clients of serious issues within their furnace allowing them to shut down their smelters ahead of predicted failures and possible disasters. This paper presents the results of several smelter AU-E inspections of the hearth and sidewall. These case studies demonstrate how the AU-E results were used to positively affect the smelter operation.

By Shoji Taniguchi, Lifeng Zhang, Kaike Cai

"In the present paper, based on the two-phase (Eulerian-Eulerian) model, the 3D fluid flows in gas-stirred systems, i.e., air-stirred water vessel and argon-stirred liquid steel ladle, are simulated. In the Eulerian-Eulerian two-phase model, gas and liquid are considered to be two different continuous fields. The phases are assumed to share space in proportion to their volume fractions. The exchange between the phases is represented by source terms in conversation equations. Turbulence simulated by the k- e model is assumed to be the property of the liquid phase. The following effects of mathematical treatments and operational factors on the fluid flow are discussed, such as interphase drag force, turbulent model, the size of bubble, and gas injection mode.Some interesting results are derived. Except the interphase drag force, the interphase lift force should be taken into accounted in order to exactly simulate the fluid flow in gas-stirred systems. Suitable turbulent model and drag coefficient have effect on the mathematical simulation. Injecting small bubbles can realize a well mixing flow condition. The distance between the two gas-injection nozzles has effect on the fluid flow."

Jan 1, 2000

By Massoud Hassanabadi

Filtration using Ceramic Foam Filters (CFFs) is a method widely used to separate inclusions from molten aluminium. In the present work, the specific permeability and form drag coefficients of nominal 50 mm thick commercial Al2O3- based CFFs, of grades 30, 50, 65 and 80, have been calculated from pressure drop experiments using high (60–500 mm s−1) and low (0.2–10 mm s−1) water velocities. Moreover, 2D axial symmetric Computational Fluid Dynamic (CFD) models have been developed, using COMSOL Multiphysics® to validate the experimental results. The empirically obtained values were defined as global parameters used to model the pressure, as well as the velocity fields in the water pipes and in the CFFs. The modelled pressure drop over the filter thickness for the high water velocity experiments showed < ± 1% deviation from the corresponding experimental results for all CFF grades. Moreover, the developed model also showed good agreement with the experimental results obtained from the low water velocity experiments, where the deviation of the pressure drop for the CFF samples of grade 30, 50 and 65 were ≤ ± 4.6% and for CFF samples of grade 80 ≤ ± 13.4%.

By Michael J. Marinigh

"Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable.In converting furnaces which have tuyères such as the Noranda Reactor and the Teniente, Peirce- Smith and Hoboken converters, efficient tuyère line management is critical to optimizing blowing rates, increasing refractory life, and improving safety.This paper will describe recent improvements made to equipment used for tuyère punching, tuyère silencing, tuyère pyrometry and refractory drilling of tuyères and how the proper application of the equipment can lead to operational and safety improvements."

Jan 1, 2009