Search Documents

By Lars O. Werme

Already the KBS Project proposed copper as a suitable material for encapsulation of spent nuclear fuel. The basis for this choice was the thermodynamic stability of copper in water and the fact that deep granitic groundwaters in Sweden are oxygen free. With a limited supply of oxidants, a copper canister would have the potential for a very long service life. The research and development work aiming at encapsulating nuclear fuel entered a new phase in 1993, when SKB launched its Encapsulation Plant Project. Within this project, SKB has: ? designed a facility for encapsulation of nuclear fuel, ? laid down the design premises for a canister for disposal of nuclear fuel, ? tested and developed fabrication methods for copper canisters, ? evaluated the long term chemical and mechanical behavior of the canister, ? made preliminary plans for a factory for the production of copper canister, ? constructed a canister laboratory for full scale testing of the key operations in an encapsulation plant. The conclusions of this project were that a canister consisting of an outer layer (50 mm) of copper over an insert of cast nodular iron would provide sufficient corrosion protection and would have sufficient mechanical strength. This canister can be produced by several methods of which forming from rolled plates, hot extrusion, and "pierce and draw" have been tested at full scale. The canister will be sealed by electron beam welding in the encapsulation plant, and the integrity of the weld will be verified by ultrasonic testing and' high-energy radiography. The final development work in this area will be performed in the canister laboratory.

Jan 1, 1999

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Jie Qiu, Yun Chen, Kai Tang

The influence of SiO2 on the reducibility of the CaO–Fe2O3–SiO2 system was fully examined in this study. The isothermal reduction kinetics of CF and CF8S (CaO/Fe2O3 = 1:1, wt% (SiO2) = 8) were investigated through thermogravimetric analysis at 1123, 1173, and 1223 K with 30% CO and 70% N2 gas mixtures. The reduction of the samples with 8% SiO2 was not only highly accelerated but also proceeded easily. Rate analysis revealed that CF and CF8S reduction occurs in two stages, the Fe3O4-to-FeO stage overlaps with the previous Fe2O3-to-Fe3O4 stage and tends to approach the following FeO-to-Fe stage with the addition of SiO2. The apparent activation energy values of CF and CF8S reduction are 46.89 and 8.71 kJ mol−1. Sharp analysis indicated that CF and CF8S reduction was expressed by the Avrami–Erofeev equation presenting a 2D shrinking layer reaction.

Mar 1, 2017

By C. F. Ferron

A process has been developed to treat the copper gold ores from the Guelb Moghrein mine in Mauritania. The process consists of pressure leaching the sulphide concentrate, neutralising with the oxide ore, recovery of copper by SX/EW and of gold by cyanidation of the autoclave residue. This paper focuses on the pressure leaching step, and presents data from bench and pilot plant test programs. In particular, attention is drawn to the effects of temperature, grind size, neutralisation, retention time and solution recycle on the kinetics of copper dissolution from various flotation concentrates. Likely leach mechanisms are briefly discussed.

Jan 1, 2000

By Marcel Magnusson, Guozhu Ye, Pekka Vaananen, Yang Tian

The most used technology for recycling of spent alkaline batteries consists of crushing, magnetic separation and processing of the nonmagnetic fraction, black mass, using a rotary kiln. In the process only zinc is recovered and all manganese in the black mass is lost. According to the EU regulation for recycling of batteries, more than 50% of batteries should be recovered. To meet the demand, Swerea MEFOS has together with a major battery recycler IsoLogistics in Finland and Sweden developed technologies for efficient recovery of zinc and manganese aiming for >50% recovery. This paper will focus on a treatment process using a DC furnace to produce a ZnO- and a MnO-product. The process has been demonstrated in pilot scale, 1 ton/h. The major outcomes will be highlighted. Another approach by using thermal vacuum technology for distillation of zinc metal has also been demonstrated in laboratory scale which is also reported in this paper.

Mar 1, 2018

By C. Carreno, A. D. Gonzalez Escarcega, M. A. Neri, A. Martinez –Villafane, O. Cobarrubias-Alvarado

"Waspaloy is a superalloy used to manufacture some aeronautical parts subjected to high temperatures and stresses. During thermo-mechanical processing cracks are generated, causing some parts to be rejected. In order to determine the causes of these cracks, this alloy was characterized using techniques such as chemical analysis, optical microscopy, scanning electron microscopy, and EDX analysis. Heterogeneous grain sizes in the microstructure cause a non-uniform strain distribution in these parts, creating cracks in zones with different grain sizes.IntroductionNickel-base superalloys are important materials for high-temperature service applications. The manufacture of components from these materials is typically based on solidification or powder-metallurgy processes [1]. Solidification techniques comprise either the direct casting of parts or the casting of ingots which subsequently undergo a series of thermo-mechanical-processing steps to refine the microstructure. During solidification, microsegregation is usually unavoidable. The primary solidification product is a disordered nickel solid solution with an fee crystal structure (?). In many alloys, the material which solidifies last is a mixture of ã and an ordered fee phase (? '). In prototypical nickel-base superalloys, the ?'-phase is Ni3(Al,Ti) [2-3].Waspaloy is a superalloy that is used in demanding high-temperature environments in which good creep and fatigue resistance are required. One of the most common applications of Waspaloy is for turbine engine rings. To ensure the required mechanical properties, the rings are usually forged and heat treated (Figure 1). Two distinct types of microstructures are usually found to be attractive for such applications: a) A microstructure with a grain size of ASTM 10 to 14 for tensile strength, ductility, and resistance to crack nucleation in low-cycle fatigue; or b) A microstructure with a grain size of ASTM 4 to 8 required for creep strength and resistance to crack propagation [4]. Because it is impossible to refine the grain size through heat treatment, a skillfully designed forging process is crucial for the control of the grain size and, hence the properties of the forged ring [5-6]."

Jan 1, 2012

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2:1. The samples having the density more than 99% of the theoretieal value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical casting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the. oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By M. S. Moats

The treatment of oxidized residues of zinc with high iron content continues to present a technical challenge in both the steel and zinc industries. Two main problems are commonly identified and include high treatment costs and environmental concerns about contaminated, iron-bearing residuals. A new approach to this problem is described in which selective separation of the iron and zinc into salable products may be potentially feasible. The waste material is first leached to give a solution having an approximate concentration of 110 g/l Zn, 15 g/1 Fe and 40 g/1 H2SO4 and other impurities such as Pb, Cd, Cu and Sb. A suitable organic, such as D2EHPA, is used to load the majority of the iron. The aqueous phase is then acceptable for zinc electrowinning after standard solution purification. The novel step in the flow sheet is the efficient recovery of the ferric iron from the organic solvent using a solid metal to reduce the iron to the ferrous state. The Fe+2 is easily stripped into an aqueous phase in a relatively pure form, suitable for use in water treatment. Process parameters and possible flow sheet designs are described and discussed.

Jan 1, 1995

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By M. Arenas

A corrosion study of a bonded NdFeB permanent magnet materials alloyed with titanium carbide additions has been undertaken. The materials were produced by rapid solidification by melt spinning. Commercial epoxy was used as a bonding medium. The corrosion results were compared with those of a near stoichometric unalloyed NdFeB. Anodic polarization and potentiostatic techniques in 0.9 M Na2SO4 solutions were used to characterize corrosion behavior. It was found that the addition of 6 a10 Tic resulted in superior corrosion resistance, as indicated by lower corrosion currents and less iron dissolution at fixed potential.

Jan 1, 1997

By P. K. Jimack, C. E. Goodyer, A. M. Mullis, P. C. Bollada

"We review the application of advanced numerical techniques such as adaptive mesh refmement, implicit time-stepping, multigrid solvers and massively parallel implementations as a route to obtaining solutions to the 3-dimensional phase-field problem with a domain size and interface resolution previously possible only in 2-dimensions. Using such techniques it is shown that such models are tractable even as the interface width approaches the solute capillary length.IntroductionMulti-scale modelling impinges upon many areas of science, engineering and technology where the interplay between processes occurring on disparate length and/or timescales can affect the properties of systems in a complex, and sometimes unforeseen, manner. One such is the processing of materials where interactions at the atomic scale, through the nano- and microstructural scale can have a profound affect on the macro-scale response of engineering components. Here we focus on one such problem, the crystallisation of alloy melts, to illustrate how a range of advanced numerical techniques make the modelling of such systems tractable.The modelling of solidification structures, in particular the growth of dendritic crystals, is a subject of intense and enduring interest within the scientific community, both because dendrites are a prime example of spontaneous pattern formation and they have a pervasive influence on the engineering properties of metals. For alloy systems, which form the vast majority of engineering materials, solidification involves the rejection of both solute and latent heat from the growing solid, forming a coupled diffusion problem in which both the chemical and thermal diffusion equations should be solved. The multi-scale nature of this problem arises from the disparity between the thermal and solutal diffusivities for most liquid metals, which are typically 10-5 m2 s-1 and 10-9 m2 s-1 respectively. The ratio of these two, referred to as the Lewis number (Le =Dia), is therefore typically of the order 10,000 and gives a measure of the multi-scale nature of the problem. In fact, in many cases the thermal diffusivity is so much larger than its solutal counterpart that thermal diffusion is considered instantaneous, wherein the system can be approximated as isothermal such that the multi-scale calculation does not need to be performed. This is certainly a reasonable approach in most conventional castings. However, there is a class of solidification problem in which this approach is far from satisfactory, namely Rapid Solidification (RS). The application of isothermal phase-field models in such situations are highly likely to produce spurious results or to fail totally, particularly for temperatures below To (the temperature at which the free energies of the solid and liquid phases are equal at the concentration of the bulk alloy), wherein partitionless solidification may occur."

Jan 1, 2013

By Luben Savov

This paper presents recent research works on the removal of the tramp elements Cu, Sn, Zn and Pb from steel. The evaporation of Cu and Sn in iron-based melts treated at reduced pressure of the gas phase was studied in a vacuum induction melting furnace. The effect of chamber pressure, temperature and melt composition was investigated. Since the main source of contamination of steel with Sn and Zn is the recycling of tinplate and zinc coated steel, respectively, possibilities for the removal of meta1ic coatings in a scrap pre-treatment stage were studied, too. Tin was removed in the temperature range 400-5S0°C by treatment with reactive gases featuring high sulphur potential. Zinc can be removed by evaporation or by a combination of thermal and mechanical treatment. The paper discusses the thermodynamics of Pb in carbon-saturated iron melts, too.

Jan 1, 2001

By M. del C. Ruiz

The extraction of Nb and Ta from a columbo-tantalite of San Luis, Argentina, is being studied by using a pressure reactor and HF as leaching agent. The reagents and products have been characterized by several techniques such as scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDXS), X-ray fluorescence (XRF), X-ray difracction (XRD), surface area (BET) and size particle analysis. Experimental results have shown that the extraction of niobium and tantalum increases with increasing temperature, reaction time and acid concentration. For particle size between +80 and -355 mesh no significant changes are detected. It is also slightly affected by the stimng speed. XRD analysis of the residues did not show formation of new crystalline structures.

Jan 1, 1999

By Abdulkader M. Abed, Shadia J. Ikhmayies, Bothina M. Hamad, Belal S. Amireh, Yulia Valery Meteleva

This work is a first step on the way to characterize raw sandstone in Jordan, and to extract silica and silicon for the use in solar cells and other industries. Seven samples of raw sandstone were brought from Disi in Jordan. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), and X-ray fluorescence (XRF). The XRD diffractograms showed that silica is the main constituent of the samples, and two samples contain Kaolinite Al2(Si2O5)(OH)4. EDS reports showed that all samples contain aluminum and carbon, but some of them contain calcium. XRF measurements revealed that some samples contain more than 97% silica, while one sample contains more than 90% silica, and the main impurity is Al2O3. FTIR revealed the known bands of silica, and this sandstone is free of organic compounds impurities.

Mar 1, 2017

By Hector M. Lizama

A new technology, known as the HydroZinc? process, is described for the recovery of zinc from sulphide ores that includes heap leaching, neutralization, solvent extraction and electrowinning. Unit operations were scaled up from bench-scale to a 1-t/d zinc cathode demonstration plant. Bench-scale studies defined the process chemistry and a process flowsheet. Column tests were used to design full-scale heaps for zinc bioleaching, and mini-pilot equipment was used to design a solvent extraction circuit. The characteristics of the process required development of a bleed circuit for water and impurities. The complete integrated process was tested on a demonstration plant scale for two years, with about 10 000 t of zinc sulphide ore being bioleached in two 6-m-tall test heaps. In addition to 1 t/d of zinc cathode, iron hydroxide and gypsum residues were produced. The process also generated a small effluent bleed. Over the course of the two-year demonstration test, a number of technical hurdles were overcome and several improvements were made. Some of the more significant ones are presented along with process descriptions and experimental and demonstration plant data. Some engineering aspects and economic evaluations of the new process are also discussed.

Jan 1, 2003

By Jonathan M. Berkoe

Design engineers and metallurgists have long recognized the need for better methods to calculate a wide range of fluid dynamic effects in smelters and hydro- metallurgical facilities. Examples can range from the capture of fume in the secondary hoods of a copper converter, to controlling the thermal effects of heat transfer resulting from metal and slag flows within a furnace. With the advent of relatively low-cost, high- speed computers and user-friendly, commercially available computerized fluid dynamic (CFD) programs, these calculations can now be made. Use of CFD increased the understanding of both hot gas and molten flows in smelter facilities and has already led to design improvements in converter fume control hoods as well as improved management of heat transfer in electric furnaces. This paper will present two representative CFD applications to metals industry facilities. To date, Bechtel has implemented CFD results on four continents.

Jan 1, 1999

By M. Nilmani, J. Sofra

The transverse distributions of the solids discharge velocity and mass flux at the discharge end of vertical and inclined lances were measured in order to detennine the transverse distributions of the axial momentum flux, which is a dominant factor influencing the penetration behaviour of particles into melts during submerged injection. The effects of gas velocity (10 - 30 m/s), solids loading (5 - 10), lance length (0.15 - 1.0 m), lance inclination (vertical downward - horizontal) and particle density (2500 - 8900 kg/m3 ) were investigated, while the lance diameter and particle size were fixed at 10 mm and 220 µm respectively. The particle velocities and mass fluxes were measured by image analysis of particles illuminated in a laser-generated light sheet aligned vertically through the axis of the lance at the discharge point. The particle discharge velocity profiles for vertical downward flows were synunetrical about the centre-line of the lance, with the maximum velocities occurring at the centre-line. The velocities increased with increasing gas velocity, increasing lance length and decreasing particle density in accordance with previous observations. The transverse mass flux profiles were also synunetrical for vertical downward flows, however at the lower gas velocities the peaks in the profiles were displaced from the centre-line of the lance by a fractional diameter of about 0.15. The particle discharge velocity profiles become increasingly asynunetric as the lance orientation was changed from vertical to horizontal, with higher particle velocities present near the top wall of the lance. The mass flux profile also became asyrrunetric as the horizontal orientation was approached, however in this case, the profile became biased towards the bottom of the lance. The effect was much more pronounced for a gas velocity of 10 m/s than for 30 m/s, showing the relatively stronger gravitational influence as the velocity was reduced.

Jan 1, 1996

By Wei-ling Wang, Ryosuke O. Suzuki, Xiang-ning Meng, Miao-yong Zhu

"A finite-element thermal-stress model of continuous casting mold is conducted to predict deformation of copper plates and its change with different cooling structure. The results show that deformation behavior of copper plates is mainly governed by cooling structure and thermal- mechanical conditions, deformation amount is related to structure geometry, and a small deformation mutation occurs in cooper-nickel boundary due to different properties. The maximum deformation of hot surface centricities of wide face locate at 100 mm below meniscus and that of narrow face locate at meniscus and terminal of water slots and significant curvature fluctuations on both sides of copper-nickel boundary. The maximum deformation of centricities is increased up to 0.05 mm with thickness increment 5 mm of copper plates, and maximum deformations are only depressed 0.01 mm and 0.02 mm with increments of 1 mm nickel layer thickness and 2 mm water slot depth respectively.IntroductionIn conventional continuous casting of steel, a large amount of sensible and latent heat of molten steel dissipate in primary cooling zone and make continuous casting mold under enormous heating load giving rise to thermal stress, deformation, high-temperature fatigue and creep not only depress mold life-span, but reduce casting stability [1] Many studies focused more on heat transfer, solidification and shrinkage of solidifying shell to provide inverse proposals for optimizing cooling system and even designing new taper of mold [2,3], but it is generally useless to those of having been manufactured or being put into production. Therefore, mold-related forward problems show necessity to be discussed deeply, and stress and deformation distributions based on special thermal conditions in mold should be analyzed in order to explore suitable cooling structure of mold directly. Samarasekera et al. [4] examined heat flow and distortion of two-dimensional longitudinal sections and investigated effect of cooling water velocity, copper plates thickness and carbon content on formation of rhomboidity and longitudinal comer cracks. O'Connor et al. [5] developed a three-dimensional mathematical model to compute thermo-mechanical state in thin-slab mold and calculated temperature and deformation of mold wall to assess roles of various process parameters on impacting mold life. Thomas et al. [6] predicted temperature, distortion and residual stress in mold and indicated increased distortion requires increased remachining, which reduces mold life and increased residual stress increases the probability of a catastrophic crack failure. Park et al. [7l determined heat-flux profiles in funnel-shaped and parallel thin-slab molds based on an inverse heat conduction model and thermocouple temperature measured in-plant and put them into three- dimensional finite-element thermal-stress model to predict temperature, distortion and residual stress of mold wall. Korie et al. [SJ focused on prediction of temperature, distortion and residual stress in mold and in particular to clarify that mold life is significantly affected by temperature and its rigidity, but little effect by mechanical including clamping force, bolt prestress, friction and ferrostatic pressure. Meng et al. [9l predicted temperature and thermal stress in a slab mold and analyzed effect by cooling system geometry and casting speed quantitatively. In present study, a three-dimensional finite-element thermo-mechanical model with type-switched element is transformed from previous heat-transfer finite-element model [9l, and mold deformation is simulated in order to shed light on thermo-mechanical behavior with special thermal conditions and different mold geometry at high casting speed."

Jan 1, 2013

By Suguru Kohno, Yoshihiro Momose, Masakazu Honma, Tokirou Kamosawa

Copper metal surfaces have been examined by an extremely sensitive surface analysis technique called temperature programmed photoelectron emission (TPPE). The surfaces were ultrasonically cleaned and subsequently abraded by a screw in organic solvents and water. The TPPE apparatus is composed of a Geiger counter with Q gas (He+ iso-C4H10). The curve of photoelectron emission (PE) intensity vs. wavelength from 300 to 170 nm, termed PE spectrum, was repeatedly measured at different temperatures in the temperature- increase process from 25 to 350°C. The number of emitted electrons in a PE spectrum (PE total count) increased, reached a maximum at-250°C, and decreased with increasing temperature. With the surfaces cleaned alone in the liquids the maximum PE total count decreased in the order C3H70H > (CH3) 2CHOH > C2HpH > CHPH > H2O. With the mechanically abraded surfaces in the liquids the maximum PE total count changed as a function of the abrasion period and the maximum tended to appear at higher temperature with increasing abrasion period; the maximum value at 10-min abrasion decreased in the order H2O > CHpH > C2HPH > (CH3) 2CHOH > n-C3HpH. It was suggested that the TPPE behavior can be related to the acid-base interaction between the alcohols and the abraded metal surfaces and the presence of a contaminant over layer on the surface. From the XPS analysis of the 01 s spectra it was suggested that the chemical change of the adsorbed oxygen to oxide oxygen with temperature plays a substantial role in the appearance of the maximum PE total count.

Jan 1, 2000

By Akio Ohta

The Hyuga smelter has been producing ferronickel by a rotary kiln-electric furnace process in Miyazaki, Japan. Several approaches to improve our operation have decreased the electrical energy consumption. A new process was developed to decrease the cost of energy even further. Oil and technical oxygen are injected through lances to heat up the calcined ores (calcine) instead of the electric power. Main problems during the development of the process were the short life of the water-cooled lances, the check on security of the safety system and the eruption of combustion gases through the calcine bed. These problems have now been overcome successfully, and stable operation can be maintained. The addition of 1 Litre of heavy oil per tonne of ore can save the electrical energy requirement by 8.6 kwh per tonne of ore. The new process has resulted in a reduction of the electrical energy consumption by more than 10 percent

Jan 1, 1992