Search Documents

By G. R. Adams, N. Y. Tang, N. Qiang

"Aluminum is the most important alloy addition to Zn baths for controlling the reaction kinetics between the steel substrate and molten Zn in continuous galvanizing operations. Due to the complexity of the Zn-Fe-Al ternary system, the measurement and control of effective bath Al remains a challenge for modem galvanizers. The successful development of Al sensors has made the real-time measurements of bath Al contents possible. To facilitate their application, a computer interface and a palm-size data logger have been developed by Cominco. Plant applications indicated that the sensor possessed sufficient accuracy for process monitoring and control. The working mechanism of the Al sensors and Cominco's development work is described, and the results of sensor applications are presented.IntroductionControl of bath Al content is critical in modem continuous galvanizing because it has a strong influence on coating structure and properties and the overall product quality. The control of effective bath Al content (Al in liquid solution) is particularly critical for galvannealing where a high bath Al content may lead to incomplete alloying during post annealing, and a low bath Al content may result in other operation problems, such as excessive bottom dross accumulation and difficulties in coating thickness control. The desirable accuracy of the Al control is within ±50 ppm of target levels. In principle, such an accuracy is achievable for modem chemical analysis facilities, such as atomic absorption photospectrometer (AAS) and induction-coupled plasma (ICP). However, a recent study carried out by the International Lead and Zinc Research Organization (ILZRO) indicated that such an accuracy is rarely achieved in the zinc and steel industries.(1)"

Jan 1, 1997

By C. Dresen

This paper discussed the reaction kinetics of the reduction of industrial phosphate pellets for P4 production. In the reduction process of various phosphate ores, the following parameters were investigated: Diffusion of the phosphorus oxide and other gaseous products from the reaction mixture after having been reduced on the reductant (coke) surface. Influence of silica on reaction kinetics. Temperature influence. Influence of mineralogy and morphology (different ores). Particle size influence of silica and coke. Experiments were carried out in a vertical tube furnace with 2 ores, 2 types of silica and one type of coke. Selected experimental conditions simulated furnace conditions. The following conclusions could be made: Reaction rate increases with the addition of SiO2 into the pellet. The reaction rate increases above 1350°C (melting temperature of the slag). Mixing different ore types in the pellets leads to differences in reduction kinetics. Particle size of the coke particles influence reduction kinetics. The amount of slag formation is influenced by silica addition, coke size and temperature.

Jan 1, 2002

By G. T. Lapidus, O. J. Solis-Marcial

"The oxidative dissolution of copper from refractory minerals, such as chalcopynte, represents a technological challenge that has occupied hydrometallurgists for more than half a century. Innumerable processes have been suggested, but the majority operates at high temperatures or employs corrosive media. The origin of this refractory nature is the formation of passivating phases of iron(III) or copper. One option is to add non-corrosive ligands that complex these metal ions, thereby facilitating their dissolution. In the present work, the effect of acetone in sulfuric acid solutions was studied. The initial experiments were on chalcopynte carbon paste electrodes using cyclic voltammetry, where greater reactivity was observed. Later, leaching tests with hydrogen peroxide, cupric sulfate and ozone and, as oxidants, were performed. High extractions were achieved in three hours at 50°C. The solid residues contained the iron in the form of Fe203 and FeOOH.IntroductionChalcopyrite is the most important mineral of polysulfide copper ores [1] and accounts for approximately 70% of the world's copper reserves [2]. Currently, the copper present in chalcopyrite is extracted mainly by pyrometallurgical processes, which generate environmental concerns because of the formation of SO2 gas and submicron particulates [3]. The development of a less aggressive hydrometallurgical process for the extraction of copper would constitute a possible solution to these problems. For that reason, studies of the dissolution behavior of chalcopyrite are of great technological importance [4], However, the proposed oxidative leaching routes for chalcopyrite, generally at high pressures and temperatures, have not been implemented on an industrial scale, because of the elevated costs required to equal the high copper extractions obtained in thermal processes. These extreme leaching conditions are required because of the refractory nature of chalcopyrite. Passivation has been used to explain this phenomenon, although researchers have disagreed on the composition of the layer, which is various have assumed to be sulfur, copper sulfides, and iron-bearing jarosites or hydroxides [5]. If the latter compounds are the cause, an alternative solution would be the use of polar organic solvents in the oxidative leach to decrease the formation of the passivating iron layer. In this work, the influence of acetone on the oxidative leaching of a chalcopyrite concentrate at room conditions is explored."

Jan 1, 2012

By T. W. Turk

In May 1984, Davy McKee Corporation was awarded a contract for engineering design, procurement assistance, project management and startup services for two gold recovery plants? in the People's, Republic of China (PRC). The basic design of these two projects was to be accomplished by a combined effort of the Chinese and Davy McKee Corporation (DMC). The, design goals were to provide a state-of-the art plant while maintaining Chinese standards and design practices whenever possible. Chinese-manufactured equipment was to be used as much as possible. This paper discusses the project organization and procedures developed to accomplish the design goals, the process selection and design, and the selection and procurement of equipment outside of the PRC. Design development for grinding, leaching and carbon adsorption, and gold recovery are discussed in detail. The major goal of process selection and design was to provide common criteria for both plants. Equipment .sizing and selection was identical for carbon-in-leach adsorption, gold recovery, acid washing, and carboo regeneration for both plants. Of special importance is the design of the wastewater treatment system. Due to the cl0se proximity of a major population area, slurry discharging from these mines must be treated to meet drinking water standards. The process development and design of this system is also discussed in detail.

Jan 1, 1989

By Carla Lupi, Alessandro Pescetelli

"Spent lead battery recycling still shows few weak points in the achievement of a 100% recycling of different waste matters and by- products arising from the recycling process. Some of said problems are dealing with aqueous streams outgoing the recycling plant, and more particularly, a) the waste waters discarded from the breaking and separation unit, b) purification of the spent electrolyte drained from waste batteries and upgrade to a quality compatible with full re-use by the batteries’ manufacturers, c) purification of the mother liquors discarded in the sodium sulfate crystallization process so to produce a salt of commercial grade. All of the above listed problems have been satisfactorily overcome applying an electrochemical process that, through different process conditions and parameters, is able to remove the harmful impurities that hinder the successful commercialization of such by products, or, at least, that can avoid heavy and expensive treatment plant and operation.IntroductionAlmost 100% of commercial lead and lead alloys produced by secondary lead plants is recycled to the new lead accumulators manufacture. The other by-products and residues produced through the lead recycling process may be classified into two groups:a) matters reusable in the new accumulators production processb) matters produced as a result of various reagents and additives used in the recycling process, to be sold to different market sectorsQuality and saleability of by-products are significant points for the economics of the secondary lead plant operation, because, if said by-products are not saleable, they are just wastes, so offsetting potential revenues, and, at the same time, adding a heavy burden to operating cost, like disposal cost [1]. When looking at a typical, modern lead scrap batteries recovery cycle, it is quite evident that we are still rather far from dealing with a waste-less technology (fig.1).The group a) includes 3 by-products produced through the breaking process: among those matters the polypropylene only usually reaches a standard quality suitable for sale to lead manufacturing sector or to other sectors as well. The other two by-products, electrolyte and separators, do not still reach, through a viable and effective regeneration process, a quality standard sufficient for their re-use in the lead batteries sector ."

Jan 1, 2008

By E. C. T. Chao

Micro-optical and synchrotron radiation-induced X-ray fluorescence (SXRF) techniques have been used to study unoxidized and oxidized samples of Carlintype sedimentar,y rock-hosted disseminated gold ore. In these samples, Where much of the gold is submicroscopic, the SXRF technique, which has a spatial resolution of about 20 ~m and a minimum detection limit (MDL) in the ppm range, is an ideal and necessary tool for precisely locating gold-rich areas in a sample. Gold-rich areas pinpointed by SXRF were later studied in detail by micro-optical methods, principally optical microscopy and scanning electron microscopy with energy-dispersive X-ray analysis (SEM-EDX). In two unoxidized and one oxidized ore samples, SXRF analyses have shown gold to be present predominantly in discrete clay-rich and silicified areas. Gold was not detected by SXRF in association with pyrite or carbonaceous materials. SEM-EDX examination of the gold-bearing areas in the unoxidized samples succeeded in identifying only two free gold particles, 0.2 and 0.5 ~m in size. In the oxidized sample, gold particles appear to be larger (but still submicroscopic) in average size and more evident in micro-optical examination after SXRF location of goldbearing areas. The findings of these studies may help to improve the efficiency of processing and recovery of gold from unoxidized ores.

Jan 1, 1987

By Xiao Yang

Calcium oxide is one of the major fluxing agents used for steel refining. Because unreacted CaO remains in slag in most cases, discharged slag is difficult to be recycled smoothly. With the growth of environmental concerns, improving utilization efficiency of CaO is required to reduce the amount of discharged slag and energy consumption. The authors have reported a resource and energy-saving process by using multi-phase flux for dephosphorization. Reaction behavior of phosphorus in multi-phase CaO–FeOX–SiO2–P2O5 flux system was investigated. Formation mechanism of P2O5-rich phases was clarified at the interface between solid CaO or 2CaO, SiO2 and molten CaO–FeOx–SiO2–P2O5 slag. Phase relationship and thermodynamic properties of 2CaO, SiO2-3CaO, P2O5 solid solution were observed to confirm the condensation of P2O5 in solid phase. Based on these results, reduction of CaO consumption, discharged slag curtailment, and energy-saving effects in the novel refining process by using multi-phase flux were discussed.

By George J. Karcas

"Non-ferrous metals such as copper, nickel, lead, zinc and precious metals are produced via the electrorefining and electrowinning processes. Apart from controlling electro-chemical conditions for the production of these metals, there has always existed the challenge of controlling the corrosive effect of the electrolyte environment which serves as the medium for non-ferrous metal production.The practice of acid containment in electrometallurgical operations has entered the world of high technology with the advent of advanced acid resistant materials such as vinyl ester resin which is either combined with aggregate to form polymer concrete or used to line various acid containment vessels and ·surfaces. ill comparison to some Asian, European, and African copper refineries, the North and South American copper industry has recently embraced quite heavily in the use of polymer concrete electrolytic cells and process vessels, such as electrolyte storage tanks, and in the use of vinyl ester resin for corrosion protective surface sealing 'systems in lieu of epoxy, acrylic and other materials because of its combination of higher corrosion resistance and superior flexibility.Electrolytic cell construction has undergone a transformation from a multiple part configuration to a single piece moulded/cast unit. ·The one piece moulded polymer concrete cell, which has been patented by Corrosion Technology International, with the overflow, decant, inlet, fast fill and segregation systems integrally designed is now the industry standard.. The combination of a wood, steel, or concrete frame with a lining made of lead, asphalt, rubber or plastic has been historically successful in providing limited protection from chemical and mechanical attack in electrolytic cells and electrolyte storage tanks all over the world. These combinations have now become obsolete as materials such as polymer concrete provide exceptional corrosion and mechanical protection with greatly reduced maintenance requirements and improved efficiency and productivity for the tankhouse. ill addition, polymer concrete can be disposed of in a regular land fIll which is much less costly than disposing of contaminated concrete that is normally associated with conventional lined concrete cells."

Jan 1, 1997

By A. A. Shook

The off gas from the #5 converter at BHP Copper's San Manuel smelter was analyzed continuously over a period of several weeks using an online sulfur dioxide analyzer. These data have shown that the oxygen utilization efficiency of this copper converter was somewhat lower than anticipated, and that oxygen efficiency declines significantly during the copper blow. A sharp reduction in sulfur dioxide generation was consistently observed at the end of the copper blow, which could be used by converter operators to prevent over-blowing and minimize rolling out of stack.

Jan 1, 1999

By Shadia J. Ikhmayies

"Nanocrystalline fluorine-doped tin oxide, SnO2:F, thin films were prepared by the spray pyrolysis (SP) technique on glass substrates. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray dispersive spectroscopy EDAX and transmittance measurements. X-ray diffraction patterns revealed the nanocrystalline nature of the films where the grain size was estimated based on the Sherrer formula. SEM micrographs showed that the films are uniform and totally covered with the material and they confirmed the nanocrystalline nature of the films. The absorbance was deduced from the transmittance measurements, and its first derivative was used to estimate the optical bandgap energy. Bandgaps larger than the bandgap of the bulk SnO2iF were obtained, indicating the presence of quantum dots. The hyperbolic band model was used to estimate the radii of the nanocrystallites. A comparison between the results of the different methods was performed.IntroductionTin oxide, SnO2, thin films are n-type semiconducting, transparent materials, which have numerous important applications in optical-electronic device technology. The optical transparency of SnO2, together with its chemical and mechanical stability, makes SnO2 films suitable for many other applications, such as transparent conductive coatings, gas sensors and heteroj unction solar cells [1]. In particular, SnO2 thin films have drawn much interest because of their potential application and integration with microsensor devices. Considerable attention has recently been focused on the development of solid state gas sensors based on thin films with a crystallite size smaller than the Debye length of the material, which show increased gas sensitivity and short response times [2]. In many of these applications, a doped SnO2 film is used as an active layer. Among the various dopants, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [1]."

Jan 1, 2012

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By John A. Clark, Danylo Oryshchyn, Casey Carney, Stephen Gerdemann, Cathy Summers, Thomas Ochs

"Limited analysis of combustion gas streams where carbon capture is not of interest is done mainly to ascertain operation parameters. Stringent regulations on acid gases and particulates promote careful flue gas analysis. Unregulated components are typically not analyzed. Typically not more than four points (two in the boiler, and one each in the flue and the stack) are sampled. A successful oxy-fuel process with carbon capture and compression is anticipated to require as many as 12 sample points with analysis for water, nitrogen, oxygen, argon, NOx, SOx, and carbon monoxide. Carbon dioxide captured for beverages produces a high value product and the cost associated with analysis is warranted. However, carbon capture for disposal must keep all costs to a minimum. This paper will compare alternative approaches for cost-effective sampling and analysis of the carbon dioxide product streams from oxy-fuel combustion, through all stages of production through compression and pipeline/vessel delivery.IntroductionAnalysis of gases in an oxy-combustion process with carbon capture is essential to the operations of the oxy-fired boiler and the subsequent collection, compression, and purification of carbon dioxide. The process is charged with pure oxygen and not-so-pure carbon in the form of coal at the front end, generating a product of mainly carbon dioxide with traces of argon, nitrogen, sulfur compounds, nitrogen compounds, oxygen, hydrogen, and mercury. It is possible that hydrogen chloride and hydrogen sulfide may also be present in trace amounts [1]. The trace components primarily come from impurities contained in coal such as water, sulfur, nitrogen, and volatile organic compounds. Coal also contains a good deal of mineral matter that is transformed into ash during combustion, becoming particulates that can complicate the analysis regimes utilizing standard analytical equipment."

Jan 1, 2010

Arsenic occurs naturally in rocks and soils, water, air, plants and animals. It can be further released into the environment through natural activities such as volcanic action, erosion of rocks and through human actions. Higher levels of arsenic tend to be found more in ground water sources than in surface water sources of drinking water. Compared to the rest of USA, western states have more systems with arsenic levels greater than 10 parts per billion (ppb). The US Environmental Protection Agency (EPA) has historically regulated arsenic in drinking water at 50 ppb, but the agency has lowered the maximum contaminant level (MCL) for arsenic to 10 ppb-to be in compliance by January 2006.This paper reviews briefly a) aqueous arsenic chemistry and removal mechanisms and b) the available treatment processes to attain the drinking water standard of 10 ppb by 2006. The combining of an appropriate removal method with an existing system depends on several factors such as nature of arsenic, the water source, existing plant equipment and processes site conditions etc. The paper also includes one or two case studies from the State of Arizona. Key words: Arsenic, Drinking water, Treatment Technologies

Jan 1, 2005

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"Direct digital manufacturing offers promise as a technique for fabricating complex hydrogen purification membrane support structures. Free form fabrication methods can produce parts with complex structures, and sintering parameters can be controlled to adjust the density, pore structure, pore pathways and strength in catalytic substrate constructs. Efforts are underway to define the influence of selected process variables on the chemical and mechanical properties.IntroductionThe Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production. Because hydrogen readily passes through palladium, a structurally sound palladium-based membrane is capable of separating relatively pure hydrogen from other gases. In order for this technology to succeed, a suitable substrate material must be identified.High purity hydrogen is produced by various means. A common method involves a two-stage process for separating hydrogen from a hydrocarbon gas stream: 1) hydrogen-rich syngas is produced by the catalytic reaction of natural gas or another light hydrocarbon gas with steam, and 2) hydrogen is separated from the other syngas components by pressure swing adsorption (PSA) (US. Energy Information Agency, 2011). In PSA, gases enter a column that is packed with a material that absorbs gases as the chamber is filled and pressurized. As the pressure is slowly relieved, the absorbent material releases hydrogen at a higher pressure than the impurity gases. PSA processes produce 99.99% pure hydrogen at a high recovery rate. These systems typically demand a high capital investment due to the high pressure and multiple stages (columns) needed to attain high hydrogen production rates.Research geared toward reducing hydrogen production cost is focused on the development of improved catalysts and adsorbent materials as well as more effective single-stage separation processes. An interesting method combines hydrogen reduction catalysis and filtration. Nascent hydrogen is separated from other gases as it selectively permeates the filter. Catalyst filters may be made of gold, silver, platinum, palladium or precious metal alloys (Davis, 2009)."

Jan 1, 2012

By W. -S. Hwang, R. A. Stoehr, P. Ingerslev

"The flow of molten metal entering complex two-dimensional foundry molds has been modeled using the Simplified Marker and Cell (SMAC) and Solution Algorithm (SOLA) techniques. The molds were for a series of four and three-spoke wheel designs. The computer calculations were compared to physical experiments in which molten cast iron was poured into C02-bonded sand molds. The metal was photographed with a high speed motion picture camera focused through a Pyrex glass window on one face of the mold. To get good agreement between the calculations and the experiments, it was necessary to accurately represent the velocity through the ingate. This was calculated by application of the Bernoulli equation to flow through the feed system. Some difficulties were experienced with mathematical instability, expecially in the three-spoke design with a narrow ingate. This was overcome by using 100% upwind differencing, and over relaxation parameter near 1.0 (i.e. no over relaxation), and variable mesh spacing.IntroductionModeling the flow of molten metal entering molds has the potential for making significant contributions to the design of feed systems. It will supply information to the computer-aided-design systems of the future that will enable the designer to optimize the placement of gates, dimensioning of passages, and designation of casting speeds. Such design criteria have generally been based on application of energy balance (Bernoulli equation) principles to flow in the sprues, runners, and gates. Indeed, this is the easiest way to determine the proper dimensions to give a suitable filling time for a casting of a given size. A number of computer programs, including one by some of the present authors, have integrated such calculations into CAD systems. l Modeling the flow of metal inside the mold cavity requires other techniques that will handle free-surface transient flow. Stoehr and Hwang reported on the application of the Marker-and-Cell (MAC) technique to mold filling problems at the previous conference in this series at Hennicker, N.H. in 1983. 2 Although considerable progress has been made since that time in improving the accuracy, stability, and convenience of these techniques, the shapes to which they were applied remained limited. Also, physical verification of the results of the calculations was limited to water models.The work to be reported in this paper was undertaken with two objectives: (1) to apply these techniques to more complex and realistic shapes, and (2) to verify the results by comparison with flow patterns observed in molten metal poured into actual sand molds."

Jan 1, 1986

By M. A. Cocquerel

The future economic necessity of mining copper ores with a high impurity content and increased environmental awareness will require closer examination of the distribution of arsenic within copper smelting processes. A generalized approach is developed which can be adapted to specific projects for the determination of an overall process configuration to satisfy all requirements in a cost effective manner.

Jan 1, 1983

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By Daniel Kim, Ari Rantala

Efficient on-line monitoring of electrolytic cell performance in copper electro-refining has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Based on Kennecott Utah Copper's innovation Outotec has developed a novel and innovative electrolytic cell monitoring system called CellSense™ System. As the system is based on self-powering from bus bars, wireless communication, on-line adaptive modeling and easy to access information and alarming, traditional obstacles of electrolytic cell monitoring are eliminated. With cell voltage and electrolyte temperature measurements, CellSense System enables real-time cell performance discovery and early reaction to critical production or quality disturbances such as short-circuiting, flow blockages, cold cathodes or electrolyte temperature excursions. During the past few years the system has been delivered to over 3500 commercial cells. In this paper the largest CellSense™ System ever delivered and recently adapted by Kennecott Utah Copper with 1412 cells monitored on-line for high tankhouse performance, cathode quality and optimized operator work flow is presented. Early results and benefits are discussed.

Jan 1, 2012

By Weng Fu

In this study, Resin-in-Pulp (RIP) technology is used to separate Pb from a chalcopyrite slurry. Solvent-impregnated resin, Lewatit® VP OC 1026, which contains di(2-ethylhexyl) phosphoric acid (D2EHPA) in a macroporous polystyrene matrix was used, as the functional group exhibits selectivity for Pb over Cu. Adsorption pH, kinetics, as well as resin and CuSO4 concentrations were investigated. The results show that the kinetics of Pb and Cu loading are fast, reaching the adsorption equilibrium within 30 min. The equilibrium pH of 2 was chosen as optimum for operation in order to achieve a high Pb extraction rate and extent as well as selectivity for Pb over Cu. High Cu(II) concentration in solution results in Pb(II) requiring a larger amount of resin for the same degree of extraction. Regeneration and reuse tests show that the loss of adsorption capacity happens in the 1st and 2nd cycles and then the adsorption capacity stabilises for the 3rd cycle.

By H. K. Lin

Pyrite oxidation in chloride solutions was investigated with cyclic voltammetry, ac impedance and potential step techniques. The pyrite oxidation in quiescent electrolytes is irreversible and controlled by diffusion. Depression of the semi-circle in the complex plane plot has been explained mathematically based on the concept of the equivalent circuit. When the semi-circle is depressed, the mathematical formula indicates that the reaction resistance should be obtained from the intersection of the semi-circle with Z-axis instead of the semi- circle diameter. The peak charging current densities at 1.10 and 0.90 V vs. SHE obtained from the equivalent circuit coupled with the ac impedance measurements match the peak current densities obtained with the potential step measurements.

Jan 1, 1997