Search Documents

By Chao Li, Qian Li, Yong-bin Yang, Kai Li, Qiang Xie, Yuan-yuan Zhu, Dong-ye Li, Qi-bing Tan

"The permeability of sintering mix is a vital technological property in sintering process. However, it can only be measured by off-line method on samples picked from the production. In order to acquire the properties of sintering mix accurately, on-line measuring of permeability is urgently required. Based on the reflection characteristics of bed permeability on pipe flowing parameters, a new method is presented in this paper for on-line measuring of sintering mix permeability. The measurement can be performed by blowing gas flow in the bed with the measuring pipe. Measuring results are obtained by picking the data on flowing rate and pressure in the pipe. The function of flowing rate to pressure may be certain for samples with the same permeability. Thus, the permeability was determined by contrasting this function to the result of off-line measuring, and the relative coefficient or R2 value was more than 99%.IntroductionThe permeability of sintering mix is a vital technological property in sintering process, which directly determines production and quality of sinter, or even determines whether the sinter production is carried out smoothly [1,3].The permeability have more obvious influence on vertical sintering speed, which is mainly related to air quantity passing through material bed. Under certain inducing capacity and negative pressure, the vertical sintering speed mainly depends on the permeability of sintering mix. Low permeability may make burning through point of sintering move back, and the sinter mix cannot be burnt through. High permeability may make burning through point of sintering move forward, improving production efficiency by increasing the speed of sintering machine [4] Good permeability means a small resistance of fan ,reduction of negative pressure of sintering machine, and full contact between air and sulfide, which can strengthen physical-chemical reaction during sintering process and increase desulphurization rate. In gas well through material layer process, gas-solid desulfurization reaction and gas-solid-liquid heat exchange are completed and hot gas through the combustion zone supplies the sintering process with heat. Finally uniform sintering of the material layer in height and width direction is achieved [5] While high permeability index leads to weak sinter strength, fast sintering speed, short residence time of high temperature region and little liquid phase. Moreover, liquid phase in the fast cooling process is too late to fully crystallize but forming glass phase which is harmful to sinter strength as well. Bad permeability means a big fan resistance and increase of negative pressure of sintering machine, which make the air pass through material layer difficultly. When air and mix contact difficultly, removal of sulfide reduces so that desulfurization is incomplete. Meanwhile, low caking efficiency, slow sintering speed and easily burnt sinter , reduce sinter output. Therefore appropriate permeability of sintering mix is the premise of stable burning through point and satisfactory sinter output and quality."

Jan 1, 2013

By Jintao Gao, Zhancheng Guo, Chong Li

A new approach to enrich MFe and RO phase from the converter slag by super gravity was investigated. The samples obtained by the gravity coefficient G=600 and cooling rate V=5K/min from 1623K to 1373K appeared significant stratification and the MFe gathered at the bottom of sample. With the help of metallographic microscopy and X-ray diffraction, it is found that large quantity of white RO phase gathered at the lower part of the sample as the concentrate, with volume fraction appearing gradient distribution along the direction of super gravity, while the upper part was mainly composed of dicalcium silicate as the tailing. The mass fractions of the FeO, MgO and MnO in the concentrate are up to 40.46%, 6.9% and 3.91%, while that in the tailing are just 11.65%, 2.15% and 1.55%. The recovery ratios of FeO, MgO and MnO in the concentrate are 60.35%, 58.45% and 72.24%, respectively.

Jan 1, 2016

By R. Hurman Eric

The electrode in a slag-resistance electric furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power, i.e. heat needed for the operation. The control parameters are the size and positioning in the slag bath which are defined by slag resistivity, furnace resistance, cell constant and power input sequence all of which are closely interrelated. The flow of heat generated by the electrode current determines the energy distributions and thus the furnace dimensions. Heat flow models concerning vertical, horizontal and combined two-dimensional flows are discussed. All these considerations are based on the experimentally determined slag properties such as its resistivity.

Jan 1, 1995

By Timothy W. Skszek, Adrian S. Sabau, Hebi Yin, Xiaoping Niu

The microstructure evolution during solution treatment plays an important role in mechanical properties of heat-treated aluminum alloys. In this paper, models were reviewed that can predict the microstructure evolution during the solutionizing process of the aging heat treatment of aluminum alloys. The dissolution ofMg2Si particles has been modeled as a diffusion process of Mg in the a-Al matrix. The evolution of volumetric fraction of fragmented silicon as a function of time and temperature was also considered. The growth and coarsening of silicon particles during the heat treatment was considered. It was found that constitutive equations and required property data for most of the phenomena that need to be considered are available. Several model parameters that need to be obtained from material characterization were identified. Pending the availability of these model parameters, this comprehensive model can be used to describe the microstructure evolution of aluminum alloys in order to optimize the solutionizing heat treatment for energy savings.

Jan 1, 2013

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015

By Ernest D. Mast

Noranda's Altonorte custom smelter, located in the 2nd region of Chile, 20 kilometres southeast of the city of Antofagasta, started operations in 1993. Presently, 1150 tonnes per day of new feed are smelted with an 85% sulphur capture. An oxy-fuel reverberatory furnace produces a 48%-55% copper matte that is treated in 13 ft. x 36 ft. (3..96m x 10.97m) Peirce-Smith converters (two hot and one blowing). Up to thirty percent of the new concentrate is smelted via dry concentrate injection into the converters. This paper reviews the development of the concentrate drying and injection system, and oxygen enrichment at Altonorte from start-up in 1995 to the present time. The relationship between oxygen enrichment and concentrate injection is reviewed from a theoretical and practical standpoint. Concentrate injection has improved the smelter's productivity and added flexibility to the operations. Due to the relatively high matte grades and the subsequent short converting times, maintaining consistent operations was difficult at times and the smelter has gone through a learning curve. Plant operating results and experiences are presented on the impact of concentrate injection in relation to: feed treatment, blowing times, revert generation, slag quality and refractory wear.

Jan 1, 1999

By Chuanguang Bi, Wenbin Dai, Hongtao Wang, Mansheng Chu, Zhenggen Liu

Coke oven gas (COG) injection is considered as one of feasible measures to reduce carbon emission of BF. The effects of COG injection on the reduction of iron-bearing burdens were numerically simulated by means of multi-fluid BF model, which revealed that with increasing COG injection rate, solid temperature gradually decrease, in-furnace H2 concentration increases, the reduction of magnetite and wustite by H2 is evidently accelerated, the reaction rate of wustite by H2 reduction is enhanced and the reduction degree of mixed burdens is strengthened. Under this hydrogen-enriched condition, metallurgical properties of iron-bearing burdens were experimentally investigated. The GB/T13242-91 test results showed that with increasing COG injection rate, the reduction swelling index of oxidized pellets decreases while the reduction ratio of pellets increases. The softening-melting tests suggested that softening interval of mixed burdens increases from 163.6 to 228.3 °C while melting interval decreases from 147.3 to 92.4 °C. The cohesive zone moves downwards and becomes narrow. The permeability of mixed burdens is improved. In terms of metallurgical properties of iron-bearing burdens, COG injection benefits to improve BF performance.

Mar 1, 2017

By Matthew Jeffrey

Due to the increasing environmental and public concerns over cyanidation, there has been a large amount of research into viable alternative lixiviants. Despite these studies, there is little published data directly comparing the kinetics of gold leaching for each of these alternatives: most of the literature is concerned with gold extraction from ores. This paper presents a detailed kinetic study of gold leaching in cyanide, armmonia/thiosulfate and chloride/hypochlorite solutions. The gold leach rates were measured using a rotating electrochemical quartz crystal microbalance (REQCM). This instrument allows the mass of a gold sample to measured in?situ, with a sensitivity of less than 10 ng. From the results of these studies, it is possible to select experimental conditions where the leach rates of the alternative lixiviants are similar to that for the traditional cyanide system.

Jan 1, 1998

By Xue Sun, Dengfu Chen, Yuting Chen, Mujun Long, Song Xu, Helin Fan

In order to seek an effective extraction process for vanadium, the recovery of vanadium from a high Ca/V ratio vanadium slag was studied by sodium roasting and ammonia leaching. In the present paper, the oxidation and leaching process of vanadium slag was investigated by X-ray diffraction (XRD), scanning electron microscopy and energy dispersive X-ray spectrometry (SEM/EDS) techniques. The effects of ammonium carbonate concentration, leaching temperature and leaching time on the leaching ratio of vanadium were discussed. As indicated in the experimental result, the optimal (NH4)2CO3 concentration was 120g/L, leaching temperature was 60°C and leaching time was 20 min. Approximately 92% of the vanadium was recovered under the optimal conditions. Furthermore, by means of X-ray diffraction analysis, the phase transformations of the vanadium slag during roasting and leaching processes were analyzed and discussed.

Jan 1, 2014

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of titanium oxycarbide – a consumable anode material used in molten-salt processes for electrowinning titanium – from heavy mineral concentrate, such as a high-titania leucoxene and natural rutile is described. The oxycarbide is prepared by carbothermic reduction of the oxide at elevated temperature. Particle size distribution (of the titanium oxide raw material) and temperature have large effects on the kinetics of the reaction, which seem to follow a “shrinking-core” model. It is anticipated that low porosity (in the anode pellets) would be advantageous during electrolysis. Particle size distribution, extent of reaction during carbothermic reduction, and sintering temperature are expected to affect pellet porosity after sintering, and are being tested experimentally.

Jan 1, 2015

By Samantha Moodley, Rauf Hurman Eric, Cevat Kucukkaragoz, Aditya Kale

"Two titania slags, rutile and synthetic rutile were chlorinated with petroleum coke and CO in a small bubbling fluidized bed reactor. The study aims to identify differences in chlorination mechanism, compare conversion rates, blowover and the chlorination of impurities for the various titania feedstocks at different temperatures.Chlorination rates were highest at 1000ºC; rutile chlorination significantly increases as temperature increases from 800ºC to 1000ºC. At 1000ºC, synthetic rutile had the highest chlorination conversion rate; this was followed by Slag B which in turn was more reactive than Slag A and rutile. The mechanism for slag, synthetic rutile (SR) and rutile chlorination differs. Synthetic rutile feed is porous, providing a larger surface area for the chlorination reaction, hence the highest conversion rates was attained. Titania slag becomes porous with the initial chlorination of FeO and MnO whilst rutile remains solid. As the porosity of slag particles increases so does its tendency to be elutriated. Ti2O3 is oxidized within the early stages of chlorination during the chlorination of FeO and MnO. Ti2O3 not oxidized is then rapidly chlorinated.IntroductionTitanium dioxide (TiO2) is the most common compound of titanium, about 95 - 98% of extracted titanium minerals is processed into TiO2 white pigment [1]. Two processing routes exist for the production of TiO2 pigments, i.e., sulphate and chloride based processes. In the chloride process, titania feedstock is fed to a fluidized bed reactor together with reductant and chlorine gas. A temperature of 1000 - 1300ºC is maintained in the reaction zone and apart from silica, zirconia, uranium and thorium, virtually all the metal oxides in the feed are converted to their respective chlorides [2]. Chlorine is recovered and recycled back to the reactor."

Jan 1, 2012

By Dian Adisty, Leiv Kolbeinsen, Eli Ringdalen

In Si and FeSi production, the main Si source is SiO2, in the form of quartz. Reactions with SiO2 generate SiO-gas that further reacts with SiC to Si. During heating, quartz will transform to other SiO2 modifications with cristobalite as the stable high temperature phase. Transformation to cristobalite has been investigated and shown to be a slow process where the rate varies between the investigated quartz types. The effect of quartz versus cristobalite as SiO2 source has been studied for reaction (1) 2SiO2 + SiC = 3SiO + CO, by heating of pellets with SiO2 + SiC in Ar-gas. The reaction was faster with cristobalite than with quartz. Initial experiments indicates that this is the case only in Ar and not in CO-atmosphere The higher specific surface area of cristobalite is believed to contribute to the higher rate. The industrial consequences of the observed difference between quartz types are discussed.

Jan 1, 2014

By Patricia Negrini Siqueira Poveda, Leonardo G. A. Silva

Thermoplastic materials are sensitive to ultraviolet radiation (UV), which can cause structural changes, causing variation in mechanical properties and appearance. UV range between 250 and 400 nm is considered the most aggressive to polymers, and prolonged exposure to it results in breakage and/or crosslinking chains. Light stabilizer additives, blockers or absorbers are added to the polymers for protection in order to extend the life of the final product. The choice of the adequate light stabilizer additive system depends on factors such as resin final application, thickness, geographic location of exposure, presence of fillers in the composition, contact with chemicals, among others. This study evaluates different additive systems: conventional organic, inorganic nanotechnologyc base and the synergy between them when applied to polyethylene considering carbonyl index and UV/VIS results after aging by QUV chamber.

Mar 1, 2017

By P. T. Velu, R. G. Reddy

"The use of emf measurements to derive classical thermochemical data has been in use for many years. The reaction associated with electrochemical process is harnessed in a galvanic cell and energy involved measured in terms of electromotive force. The property requirements of sensor electrodes used differ for various aqueous, molten salt and solid electrolyte systems. The electrodes for molten salt electrolytes need special care for construction. This paper describes the studies carried out using an Ag/ AgCI reference electrode. This electrode was used to measure the solubility of compounds in molten salt electrolytes. The results obtained using this electrode are in excellent agreement with the values from chemical analysis method.I. IntroductionThe technique of obtaining a metal from its oxides by electrolysis is more than a century old process now. In these processes, it has been well established that for halide electrolytes, only the dissolved oxides are available for the dissociation at the electrode to release the metal during electrolysis. Therefore, the solubility of metallic oxides in the molten salt electrolytes is an important parameter which determines the economical and technical viability of these processes. The widely used molten salts systems in halides are fluorides and chlorides. The fluoride electrolyte system is used in our present study.The viability of obtaining aluminum alloys by in-situ electrochemical processing has been outlined in our earlier publications[1-8]. Studies on the solubility of various alloying element compounds is a part of our ongoing research efforts for the direct production of Al-Li alloys. As mentioned above, the solubility of lithium oxide and lithium carbonate compounds in molten fluoride electrolyte system have studied using EMF technique. The change in potential of the molten electrolyte was measured by a working electrode against the reference electrode with the addition of lithium compound."

Jan 1, 1997

By K. Sarveswara Rao

The present paper firstly describes some recent trends from literature on energy management via process intensification to arrive at sustainable technologies for aqueous processing of minerals, metals and materials. Secondly, the energy saving measures practiced in leaching, solid-solution separation, solution purification, metal and material winning and environmental aspects have been discussed. The emerging importance of interdisciplinary nature of hydrometallurgy for practical applications is also highlighted. With the above background, the present paper describes an overview of energy conservation and autoclave processes with a special reference to hydrometallurgical research activities of our Laboratory.

Jan 1, 2008

By H. Y. Sohn

A novel solvent extraction process in which the emulsion is generated by bottom gas injection rather than mechanical stirring has been developed. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration and the ease of cleaning and process control while providing a large interfacial area for mass transfer. The equipment consists of a horizontal cylindrical vessel in which the two immiscible liquids flow countercurrently. High-strength gas jets are injected from the bottom at certain intervals along the length of the vessel. The gas jet creates a plume zone consisting of an emulsion of the two liquids which contains a large interfacial area for rapid mass transfer. The two liquids then disengage and flow in the opposite directions before entering another plume zone. Thus, the process combines the simplicity of a cylindrical vessel, having no moving parts, with the contacting efficiency of a mixer-settler. The gas can be recycled in a closed loop, thus eliminating mist and other emission problems. These advantages would be especially significant for treating large-volume/low-value liquid streams which contain hazardous substances and/or suspended solid particulates.

Jan 1, 1996

By Garrett May

We present a periodic technique for measuring the thermal conductivity of thin, disk-shaped samples. In samples of this type, temperature measurements must be made across the sample faces and are therefore subject to large error due to the interface resistance between the temperature sensor and the sample. The technique uses measurements of the amplitude and phase of the periodic temperature across both a reference sample and the unknown material at several different frequencies. Modeling of the heat flow in the sample allows the simultaneous determination of the thermal parameters of the sample as well as the interface resistance. The technique is demonstrated on nanocomposite samples less than 1.0 mm thick.

Jan 1, 2008

By Patrick R. Taylor

Keywords: Thermal Plasma, Electroreduction, Electrolysis, Transition metals, Waste treatment, Molten oxides, Chromium oxide. An innovative process to treat transition metal oxide waste materials from diverse sources is presented. This technology involves using reverse-polarity DC plasma driven electrolysis in molten oxides. The process results in the recovery of the transition metal and other heavy metals from waste. By-products generated throughout the processing was converted to environmentally acceptable slag. The significance of this technology is that the treatment of the waste is accomplished in one step which in turn lowers the cost of remediation. Moreover, this process uses high temperature properties of thermal plasmas, which makes it possible to use molten oxides instead of halides as electrolytes. Chromium was successfully reduced from chromium oxide through the plasma driven electro-reduction process. It was shown that the selection of the appropriate ionic conducting oxides was critical for the formation of a slag that would enhance the reduction of chromium oxide.

Jan 1, 2004

By Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide (CO2), a major component of the greenhouse gases, could be comprehensive utilized as a valuable resource to oxidize vanadium during the converter vanadium extraction process. The thermodynamic software, FactSage, was utilized to study the oxidation ability and theoretical cooling ability of using weak oxidant CO2 as coolant in vanadium-containing hot metal. Besides, experimental research on vanadium extraction in CO2 and O2 mixed blowing extracting process had been undertaken. The results indicated that the elements C, Si, V, Mn etc. could be oxidized by weak oxidant CO2, and the content of V2O3 in slag was approached to pure O2 blowing. Furthermore, CO2 had a remarkable cooling ability and the molten bath temperature kept on decreasing as CO2 blowing rate increases. This research has proved that CO2 and O2 mixed blowing in vanadium extraction process are effective.

Jan 1, 2015

By Hélio Wiebeck, Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz

"Natural rubber reinforced commonly with carbon black to produce vulcanized material, turns into a new environmentally friendly nanocomposite when carbon black is replaced by organically modified clays of Brazil. Carbon black is substance derived from the oil refining process with consequent pollution to the environment. Its substitution in this industrial process must contribute to diminish the oil derived products dependence. As the added clays are only a third in weight of the traditionally carbon black added, then, to obtain the same final volume it is necessary to add low cost neutral filler that does not damage the technological characteristics of the final material. This paper presents results using as neutral filler of this type rice husk ashes from industrial wastes. Experiences realized with this nanocomposite material show results of quality and technological characteristics similar or superior to those of the rubber made with carbon black.IntroductionTraditionally rubbers are black or a very dark color. But they can have different appearance when filler of distinct composition of the carbon black is used. The carbon black is substance derived from the oil gotten during the final phases of the mineral fuel treatment with consequent pollution of the environment. Carbon black show nanometric grain sized distribution and a depth black color, because these properties it is also used for computer printers inks production. The substitution of this substance, traditionally used as a reinforced load in the rubber production, will have to contribute in such a way to diminish the dependence of these products as to diminish the pollution of the environment. The present work shows the results of the use of another kind of mineral nanoparticulate material substituting carbon black in the production of some rubber products. This nanoparticulate material is the organic modification of smectite clay treated with some types of ammonium quaternary."

Jan 1, 2008