Search Documents

"Depletion of known ore reserves and increased demand for precious metals have caused a revolution in biohydrometallurgical processing technology for gold recovery. Known ore deposits and future discoveries are most likely to be lower grade sulfide ores that can be difficult to recover with current leaching technology. Future metal recovery operations will increasingly use bio-oxidation techniques.Bacteria are an integral part of mineral cycling and mineral transformation in nature. Although biological processes are recognized as part of the mineralization and oxidation reactions in some ore deposits, they have only recently been applied to enhancing metal recovery in hydrometallurgical procedures. This paper explores the traditional metallurgical application of biological leaching and oxidation reactions and reviews the complete range of bacteria available for metal recovery systems. Pre-treatment of ores with bacteria improves metal recoveries in tank leaching systems and shows promise for heap leaching methods.IntroductionThere is no longer any question that bacteria playa natural role in the on-going transformation of some ore deposits (1,2). As applied to sulfide ores, a few strains have been specifically identified that exhibit a natural leaching potential (3). These bacteria can be isolated from waters and soils in old mining districts where they contribute to continuing leaching and pollution problems in acid drainage and heavy metal solubilization. Sulfur and iron bacteria as well as many heterotrophic strains have also been found in ore deposits and sedimentary rocks at depths up to 2000 meters (4). Their presence in both ore deposits and processed ores shows the microbial association with natural leaching and the potential role that bacteria can play in the development of new leaching technology."

Jan 1, 1988

By S. N. Monteiro, C. M. F. Vieira, M. M. Ribeiro

"This work has as its objective to evaluate the effect of incorporation of the powder waste retained in the eletrostatic precipitator of the sintering stage from an integrated steel making plant on the physical and mechanical properties of a red ceramic. Formulations were prepared with incorporation of the waste in amounts up to 20 wt.% into a kaolinitic clay. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 750, 900 and 1050°C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste has a potential to be used into red ceramics. The incorporation of the waste enhanced the properties of the ceramic, decreasing the water absorption and increasing the mechanical strength at all investigated temperatures.IntroductionThe sintering stage of an integrated steel-making plant is dedicated to the agglomeration of a mixture of iron ore, coke or coal, fluxes and water [1]. It is a common practice in this stage to use of solid wastes with great amounts of iron in the form of sludge and powder. One of the atmospheric pollutants generated during the sintering process is the particulate material, which is normally retained in an equipment denote as electrostatic precipitator. This equipment retains very small particulates, present in the gaseous emissions by application of an electrical potential difference in between the plates that the fluid is forced to go through. [2]."

Jan 1, 2011

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

Inexpensive and high-quality sinter has an extraordinary position in iron making, and there are many factors influencing the sintering. This research takes the basicity and coal dosage as research subjects to do the experiments based on cost analysis with sinter pot experiment system. Linear program is taken to make the schemes of ore blending. During the experiments of changing basicity from 1.6 to 2.3, the properties and microstructures of the sinter are studied. It comes to a conclusion that increasing the basicity is beneficial to sinter quality but leads to higher cost. To further ascertain the cost of sinter and the potential of saving coke, the work of improving coal dosage is taken on the basis of experiments of changing basicity. Through analyzing the results, a formula (Y=1849+261.1R-130.6C) is proposed which indicates the relation among the cost, basicity and fixed carbon content. And it works well for actual production.

Jan 1, 2015

By S. Mattlgod

Self-assembled monolayers on mesoporous supports (SAMMS) have been developed for the removal of heavy metals and some transition metals. The thiol functional groups were assembled on the internal and external surfaces of mesoporous silica with a uniform pore size of about 55 A. The mesoporous supports provide high surface area (>900 m2/g) needed for high metal loading in chemical separation. Self-assembled monolayers of organic molecules bond to the ceramic substrate with prescribed densities, and with terminal functional groups for excellent molecular selectivity. The unique characteristics include: (1) High metal absorption capacity, up to 3.2 mmol/g of SAMMS. (2) Fast Hg-binding kinetics (reducing mercury concentration from 0.5 ppm to 0.5 ppb in less than 5 minutes). (3) High selectivity in the presence of a range of cations, anions, and organic species. (4) Applicability in both aqueous and non-aqueous solvents. (5) Flexibility in surface chemistry. The materials can be designed to adsorb heavy metals, transitional metals, and radionuclides. (6) Chemical stability, and potential for regeneration or waste storage. This paper discusses the results on mercury adsorption.

Jan 1, 1999

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in at flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the prediction of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By Zhou Jun

Water-quenched samples were taken from a commercial flash furnace at three levels along its reaction shaft during operation at high feed rate. The samples were subjected to a series of analysis and observation. Such processes of the feed in reaction shaft as oxidation, desulfurization, melting, slag and matte formation and etc., variations of particle size along axial and radical direction of the shaft are investigated. The following smelting mechanism in reaction shaft named as “Multi-particle and multi-phase fusion model” is proposed: (1) Fragmentation and collision of concentrate particles take place simultaneously in reaction shaft with particle size growing up. Collision produces large-size “unit melt” which falls into the reaction layer in the settler bath. (2) In the settler reaction layer below the shaft, weak bath smelting reactions take place among the shaft products, producing final matte and slag which separate into two layers. (3) The processes in the shaft are all progressive along the whole height of the shaft. The predominant reaction in the shaft is oxidation, not reduction.

By H. D. Freeman

The occurrence of gold in refractory gold ores varies widely and affects the recovery process. The determination of gold and the composition of the associated minerals are important in selecting an appropriate processing scheme. However, locating the gold in an ore sample is a difficult task which requires perseverance, luck, and experience. Our experience has led to the development of a relatively fast and reliable means of deter-mining the mineralogy of ore samples through analysis combining an energy-dispersive x-ray analyser coupled to a scanning electron microscope (SEM). In some cases, a wave length dispersive spectrometer or microprobe is used to further quantify the various mineral compositions. The SEM/microprobe analysis identifies the source of problems that may arise during the recovery of gold from refractory gold ores.

Jan 1, 1981

By V. M. Paretsky

The basic work conducted by Prof. A.Yazawa has demonstrated that in order to ensure single-stage white metal production by autogenous smelting of copper sulfide raw materials, it is most favorable to use highly basic slags, in particular oxide systems CaO-FeO-Fe2O3-Sio2. he special studies have been conducted in the Gintsvetmet Institute to investigate the composition and structure of slags produced on a semi-commercial scale when testing the KFP and FBP processes for white metal smelting, as well as the slag obtained in a full-scale KFP furnace at the Almalyk copper smelter. The investigations conducted have demonstrated why production of high-grade matte or white metal is associated with lower loss of copper in slag in a series: silicate slag I silicate-calcium slag I ferrite-calcium slag.

Jan 1, 2003

By William Gregg

Recent environmental and workplace safety legislation has Imposed more stringent limits on the amount and type of particulate emitted Into the air. In the past, the mass of particles contained In a volume of air was the governing criteria. Now the size and precise chemical nature of the particulate must be known and controlled In addition to it's ?mass. Processors of metallic materials have to implement stricter control practices and more efficient control equipment to meet the new regulations. Pulse-Jet dust collector systems are being used to control particulate emissions from various process gas streams. Pulse-jets :are also being used for maintaining a healthy environment In the workplace. this paper will discuss the impact of these regulations, the control techniques used to comply with such regulations, and the equipment needed for compliance.

Jan 1, 1992

By LeoJ. Miller

Exploration for an ore deposit commences with an outline of the regional ore controlling environment and is followed by the application of tools to focus the target area. One of the most essential focusing is the mapping of the mineral assemblages within the area of the ore. Key elements of mineralizing fluids, either epigenetic or syngenetic, enter into mineral assemblages that extend far beyond ore deposits. Portions of these assemblages may consist of new matrix minerals or alteration of previously existing minerals. Today, ore deposits are divided into genetic classes and each class is d8fined by a specific geological environment. Ore deposits within a given class are associated with a mineralogy, that is characteristic of the ore deposit class. So faithful is the mineral assemblage surrounding, or within an ore deposit, that recognition of the assemblage may be sufficient to define the class. Porphyry copper deposits have long been noted for their halos of alter-ation minerals. The outermost ring of chlorite, epidote and calcite extend thousands of feet away from the main ore zone. The mineral associated with porphyry copper deposits have been well documented by our distinguished speaker Paul Kerr, at Santa Rita (1), and Silver Bell' (2), and by excellent papers from S. C. Creasey, 1959 (3), Sales, 1948 (4), T. S. Lovering, 1949 (5), our Co-Chairman John Guilbert, 1970 (6), and many others. Several recent porphyry copper mines have been discovered in recent years by utilizing the mineral assemblage model described by Lowell and Guilbert, 1970 (6). Dave Lowell applied his own model of mineral halos for the discovery of Kalamazoo at San Manuel (7), Arizona, and Casa Grande West, Arizona. The purpose of this paper is to outline the application of mineralogy for discoveries of deposits other than porphyry copper mines and in particular, to ore discoveries in which mineralogy has played a key roll.

Jan 1, 1981

By Yoshinobu Fukumori, Testuya Watanabe, Futoshi Shikata, Hiroyuki Tokumitsu, Hideki Ichikawa, Masahito Miyamoto

Nano-particulate systems have attracted much attention recently in pharmaceutical field as drug carriers and functional components of pharmaceutical dosage forms. This paper describes our approaches in design and preparation of nano-particulate systems, including lipid nano-emulsions, chitosan nanoparticles and thermosensitive acrylic nanoparticles, for certain pharmaceutical applications mentioned below. The lipid nano-emulsions with their particle size smaller than 100 nm were prepared for gadolinium neutron-capture therapy (Gd-NCT) of cancer by a thin-film hydration method with sonication, and intraperitoneally injected into Greene's melanoma (melanotic No. 179)-bearing Syrian hamsters. This provided such a high gadolinium concentraton in tumor as 107 µg/g tumor (wet basis) at 48 h after administration. As an alternative gadolinium nano-carrier for Gd-NCT, biodegradable and highly gadopentetate-loaded chitosan nanoparticles (Gd-nanoCPs, 426 mTI in particle diameter and 9.3% in Gd content) were prepared by a novel emulsion-droplet coalescence technique. A significant tumor-killing effect could be obtained when Gd-nanoCP suspension was injected intratumorally twice 24 and 8 hours before neutron irradiation into B 16Fl O melanoma-bearing mice and subsequently thermalneutron was irradiated toward tumor site with a flux of 2 x 109 n/cm2/sec for 60 min. As one another application of nanoparticles, a novel acrylic composite latex with a hydrophobic core and a thermosenstively swellable shell was designed for fabricating microcapsules showing thermosensitive mode of drug release. The microcapsules with the composite latex-dispersing membranes exhibited an exceptionally rapid on-off response of drug-release in a thermosensitive manner.

Jan 1, 2000

By Hongli Wen, Guangkun Shen, Qiong Deng, Shoujian Huang, Min Gan, Xiaohui Fan

"Due to the low iron grade and high sulfur content, pyrite cinder is difficult to be directly used for iron-making. In this paper, technology of magnetic roasting -grinding and magnetic separation -acid leaching was put forward for reclamation of pyrite cinder. For pyrite cinder of TFe53.51%, S2.20 %, studies showed that good magnetic effect can be achieved at roasting temperature 650~7000, reducing atmosphere CO/(CO + C02) 10~20% and roasting time 10~30 minutes. In separation conditions of grinding size -0.045mm accounting for 96.09% and magnetic field intensity of 1240 GS, iron concentrate of TFe64.81 %, S0.18% and iron recovery rate 91.44% was achieved. Acid leaching was studied to strengthen desulfurization. Results showed that high-quality iron ore concentrate of TFe66.3 l %, S0.10% was obtained under the conditions of hydrochloric acid mass fraction of 5%, pulp density of30%, leaching temperature of70? and leaching time of2 hours.IntroductionPyrite cinder is produced as a by-product of sulfuric acid industry [1] Domestic production is more than 12 million tons every year and occupied area is over 10 million square meters [2,3]. The pyrite cinder outdoor not only pollutes air but also damages surrounding surface [4] It after treatment used for iron-making is an ideal reclamation approach for its rich iron which is commonly 40-60% [5]. But pyrite cinder gets low utilization for its low iron grade and high sulfur content in China [6]. Therefore, comprehensive utilization of pyrite cinder has profound significance to environmental protection and the development of domestic iron and steel industry."

Jan 1, 2013

By Y. Z. Zhang

Electrochemical oxidation of arsenopyrite in ferric sulphate media in the absence and presence of bacteria T jerrooxidans has been investigated for the purpose of understanding the dissolution chemistry of arsenopyrite and the bacteria attack mechanism. Mixed potential, polarization resistance measurements, polarization curve, cyclic voltammetry experiments were conducted in a ferric sulphate medium of 10g/L FeH, temp.25-35°C, pH 1.5-2.5 in the absence and presence of bacteria Tjerrooxidans, respectively. For the anodic process, a two-step reaction sequence is suggested by the electrochemical measurements. The initial step at a low potential is described by:

Jan 1, 1996

By C. S. Ek

As a continuation of previous work, further tests have been carried out to recover silver from the residues obtained in a zinc jarosite process. Selective flotation has been performed with different reagents, and ?cleaning steps have been introduced to upgrade the silver concentrate. Leaching of crude residues, as well as flotation tailings, has been carried out with cyanide and thiourea. Finally, the different beneficiation methods are compared, and the industrial aspects? of their application are reviewed.

Jan 1, 1990

By T. R. A. Davey

Previous publications on the application of EIETSIM include the modelling of an electrolytic zinc plant and a copper flash smelter. In the present case METSIM has been used to model the desilverising of lead by the reagent zinc, whereby a silver-zinc intermetallic compound is formed, and floats out of the lead. This compound has a variable composition, depending upon the ratio of dissolved zinc/silver in the lead bath. Its solubility in lead decreases with falling temperature. A number of variations and modifications of the Davey Desilverising Procedure are modelled, and applied to a wide range of silver contents in lead bullions at several plants. METSIM uses both feed- back and feed-forward controls to simulate plant conditions, and a logic control to distinguish between different phases in the Zn-Ag system. Use is made of extensive (previously unpublished) fundamental data on the ternary Pb-Ag-Zn system, and of plant data, to establish certain operating parameters.

Jan 1, 1993

By Manju Gurung, Birendra Babu Adhikari, Keisuke Ohto, Hidetaka Kawakita, Katsutoshi Inoue, Shafiq Alam

Novel bio-adsorbent gel was prepared by immobilizing functional groups of glycidyltrimethyl ammonium chloride, a kind of quaternary ammonium chloride, onto polymer matrices of persimmon extract for the recovery of precious metals such as palladium(II) and platinum(IV) from chloride media. It was found that this adsorption gel exhibits high selectivity to gold(III), palladium(II) and platinum(IV) over base metals such as copper(II) and iron(III) while crude persimmon extract, the feed material, exhibits high selectivity only for gold(III). From the adsorption isotherms study, the maximum adsorption capacities for gold(III), palladium(II) and platinum(IV) were evaluated as 3.30, 1.67 and 1.00 mol/kg, respectively. Those for palladium(II) and platinum(IV) are higher than those of simple quaternary ammonium chloride type of chemically modified persimmon tannin gel and commercially available anion exchange resin.

Jan 1, 2016

By C. S. Simons

This paper presents a review of the extractive processes used in the production of nickel, with emphasis on developments since the beginning of the Second World War. Attention is given to the factors, many outside the nickel industry itself, which determined the direction of process research and strongly influenced the ultimate commitments to industrialize the resulting developments. An example of such a factor is the sudden surge in demand, far exceeding the then available nickel production capacity, that was caused by the advent of World War II; the result was the first serious consideration ever given to low- grade laterites as a viable source of primary nickel. Other factors discussed include such items as process development in the extraction of other metals - particularly copper; the availability of increasingly sophisticated materials of const- ruction; the advent of the "environmentalist" and related political developments; the massive escalation in the price of energy - particularly oil. The paper concludes with an attempt to forecast the nature of the most effective nickel process of the future, based on extrapolation from the economic and political situation that exists today.

Jan 1, 1988

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012

By E. Charles Abbey

Manganese in electrolyte has both beneficial and detrimental effects in Zn electrowinning. Mn oxidizes to form MnO2 on Pb–Ag anodes, cell walls and pipes. MnO2 reduces anode corrosion but also leads to short circuiting and maintenance issues. MnO2 is thought to interact with chloride ions and produce oxidized chlorine species. The interactions between Mn and Cl are not well understood. Therefore, two sets of 45+ day bench scale experiments were conducted to investigate the effects of the manganese to chloride ratio on anode corrosion rate and electrolyte chemistry using rolled Pb–Ag anodes. Daily manganese and chloride losses from the electrolyte appeared to be correlated. Increasing the average Mn/Cl− ratio from ∼7:1 to ∼11:1 reduced the anode corrosion rate. Increasing the ratio above 11 did not reduce the corrosion rate further. Anode scales produced with Mn/Cl− ratios at and above 11:1 contained some γ–MnO2 while scales formed with ratios less than 11:1 did not.

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011