Search Documents

By Malcolm Reeves

The heavy oil reservoirs of Alberta and Saskatchewan include sequences of unconeolidated silts and fine sands which respond in an unusual manner when subjected to the high temperature and pore-fluid-pressure associated with steam injection and other thermal enhanced recovery techniques. Apparent transient connections are suddenly established between producers and injectore and there is an associated enhancement in oil (and sand) production. These phenomena have been attributed to local fluidization and piping processes which are known to occur in situations where high pore-fluid-pressures prevent the mobilization of intergranular friction. These breakdown processes may be associated with the penetration of tongues of the heated reservoir fluids with suspended sand into the creep sensitive intact reservoir since the viscosity ratios are sufficiently high for viscous fingering instability of the fluid-fluid interface. A program of laboratory tests has been carried out to measure the strength characteristic of saturated oil sands at a variety of temperatures and fluid pressures. These tests suggest, that in common with the coarser Athabasca sands, the Waseca sands have very little cohesive strength and show the characteristic dilational failure response of dense sands. Some special tests, devised to determine the relative ease with which samples can be fluidized, confirm the expected susceptibility of the fine- sand silts. Both piping and fluidization can be readily induced at in-situ reservoir temperatures and pressures. Analysis of stresses around wellbores suggests that fluid-pressure gradients may be sufficient to initiate piping and that backward erosion along streamlines may link producers and injectors. Such pipes may act as well “adits” gathering oil from the heated reservoir and contributing to enhanced production rates. Mechanical breakdown of the reservoir by drilling, injection and production processes provides a consistent possible explanation for the sand-cut response of production wells.

Jan 1, 1986

By Robert Blair, David L. Fey, Stanley E. Church

Determination of the pre-mining geochemical baseline in bed sediments in watersheds impacted by historical mining activity is important in establishing watershed restoration goals. We have developed methods to solve this problem in the Animas River watershed, southwestern Colorado, using geomorphologic mapping to identify terraces that contain pre-mining sediments. Following a systematic evaluation of possible sites, we collected samples of pre-mining sediments in gravel deposits from 21 sites throughout the watershed. Geochemical analysis of individual layers has produced a chemical stratigraphy that can be tied to the historical record through geochronological and dendochronological studies. Analysis of geochemical data, when coupled with the historical record, clearly shows that there has been a major impact on the geochemistry in bed sediments in the active stream channel by past mining activities. Historical mining has resulted in a substantial increase in metals in the very fine sand to clay-sized component of the bed sediment of the upper Animas River, and Cement and Mineral Creeks, which are the major tributaries of the Animas River. Enrichment factors for metals in modem bed sediments, relative to the pre-mining sediments, range from 1 to 6 for arsenic, 1 to more than 10 for cadmium, 1 to about 15 for copper, 1 to more than 25 for lead, 1 to more than 10 for silver, and 1.6 to more than 12 for zinc. The pre-mining bed sediment geochemical baseline is high relative to average crustal abundance values of many metals. The Animas River watershed above Silverton, Colorado would be readily identified as a highly mineralized area suitable for mineral exploration if it were not disturbed by mining.

Jan 1, 2000

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By Arthur S. Cornford

According to Arbiter (Reference 1), the ball mill was invented by Brückner in Germany in 1876 and was first used in the United States on ores about 1905. The basic concept was a simple rotating cylindrical drum in which the tumbling action of the charge of material and grinding media resulted in size reduction of the material. Despite the very low mechanical efficiency of this method a number of factors have caused the tumbling mill to remain, by far, the most widely used piece of equipment for mineral grinding. The principal factors influencing this situation have been simplicity of design, ease of manufacture, ready adaptability to familiar material handling layouts and the absence of practical alternatives acceptable to the industry. In the early mills, the material was ground in batches, the mills being charged and discharged through doors in the shell. The shell was supported by means of solid trunnion shafts resting in plain bearings and the drive was accomplished through one of these shafts. In some later batch mills, the mill shell was supported on rollers which were also used to drive the mill. At an early stage, continuous operation was made possible by feeding and discharging the mill through hollow trunnions, the method still in most widespread use. The mechanical and structural design of the early mills was not an onerous engineering task. Norse sense and good practical knowledge were key qualifications. The mill shells had to be heavy enough to withstand the physical abuse they would receive in the field and the bearings had to have low enough unit pressures and sufficient wear retol to ensure several months of operation before the need for replacement occurred. When these requirements were satisfied, stresses developed in the equipment during operation were insignificant and the majority of structural failures were probably due to the use of inferior materials in manufacture. Over the years, the ever present demand for increased productivity has resulted in a steady Increase in the size of units of production equipment, including grinding mills. Arguments have been presented elsewhere, for and against the Idea of a high throughput single line grinding operation as opposed

Jan 1, 1972

By Charles T. Steuart, Richard B. Berg

Tripoli and the related mineral commodities such as micro- crystalline silica have been mined for more than 100 years for their abrasive properties. Although abrasive and buffing compound markets are still very important, within the last 15 years the filler and extender markets in paint, plastics, rubber, adhesives, and sealants have increased substantially. Tripoli or microcrystalline silica consists almost entirely of very small quartz crystals, many less than one micrometer in length. Material mined from different districts differs in crystal shape, grain size, and texture of the rock, all of which influence markets. Most US deposits are now mined by surface methods, and both air floated and micronized products are marketed. Deposits of tripoli now mined in the United States occur in chert-bearing Paleozoic limestone in the central part of the country with producing districts in southern Illinois, central Arkansas, and eastern Oklahoma. Although deposits within each district are confined to specific formations and extend laterally within those formations, individual bodies form minable deposits that are typically several hectares in areal extent. Tripoli is white to cream to rose and characterized by high porosity and ease of disaggregation. DEFINITIONS Tripoli In the United States, tripoli was first used to describe the fine-grained, easily disaggregated material from Seneca, MO, be- cause of its similarity to a rock from the Tripoli region of North Africa (Hovey, 1894). The North African rock is actually diatomaceous earth, a material that is similar in appearance to the rock from Seneca, but is of entirely different origin having formed by the accumulation of siliceous remains of microscopic marine or fresh- water animals. Tripoli is best defined as a very fine-grained, generally porous rock that consists of microcrystalline quartz, typically formed by the alteration of a chert-bearing limestone. Tripolite A term used to describe a rock from the vicinity of Tripoli in North Africa which is diatomaceous earth (Quirk and Bates, 1978) Microcrystalline Silica Microcrystalline silica is the same material as tripoli, but the distinction between the use of these two names is dictated largely by convention and markets. Material produced from southern I1linois deposits and used in white pigment and filler applications is generally referred to as microcrystalline silica, whereas that used in abrasive applications, both from the Illinois district and from other states, is commonly called tripoli. Amorphous Silica Amorphous silica, a term formerly used to describe the material produced from the deposits in southern Illinois, is now replaced by the term microcrystalline silica. Amorphous silica came into use when even optical methods for the identification of very fine- grained quartz were not widely available and the Illinois product, composed of quartz grains too small to be seen with the unaided eye, was thought to consist of amorphous silica. The Illinois material is clearly crystalline quartz, as shown by X-ray diffraction analysis and scanning electron microscopy (Fig. 1). Novaculite Although originally used to describe a rock suitable for the manufacture of whetstones, novaculite is now defined more generally " - as a homogeneous, mostly white or light colored rock, translucent on thin edges, with a waxy or dull luster, and almost entirely composed of microcrystalline quartz" (Steuart et al., 1983). The more compact rock mined in central Arkansas from the Arkansas Novaculite is referred to as novaculite, whereas the more porous rock is referred to as tripoli. Rottenstone The commodity rottenstone is sometimes included within the general mineral commodity category of tripoli. Rottenstone is mined in Northumberland County in eastern Pennsvlvania and formed by the weathering of a siliceous shale of Devonian age (Faill, 1979, Berkheiser, private communication, 1991). This material is used as a filler and extender, but is apparently unlike tripoli both in origin and physical properties. Spiculite Spiculite is a rock consisting of siliceous sponge spicules having formed by the removal by solution of the carbonate matrix of a spicule-bearing limestone. Spiculite has been mined in Texas and, because it resembles tripoli in several aspects, is included in the discussion of deposits.

Jan 1, 1994

By R. Asmatulu

According to Darcy's law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By Scott G. Britton

The first section of this text delves into construction engineering techniques for successfully completing necessary underground production support projects. I will discuss alternative design concepts, installation practices, materials and material costs, completion time, and necessary labor for individual projects. The emphasis of this section is on describing each project thoroughly and providing a practical guide for the supervisor or engineer. There are four main construction categories for typical underground mining projects. These are: 1) Transportation of men and supply materials. This refers to track and wire installation and roadbed grading and ballasting. 2) Ventilation, composed of overcasts, man doors, regulators, and stoppings. 3) Drainage, including sumps, pumping stations, drainage networks, pumps, and face drainage. 4) Haulage of coal and rock from the face to the outside. The focus here is in the installation of belt lines, belt drives, transfer points, and vibrating bins/feeders. The first section shall fully discuss these four categories in regard to the construction engineer or supervisor designing, building, or improving a system. In addition, special projects such as surge bins, rotary dumps, and underground offices not classified under these categories will be discussed. For manageable purposes, I have limited the installation discussions to one or two approaches I feel have merit. The variation of installations in coal mining is endless, each with its own advantages and disadvantages. Therefore, the reader should not dismiss or restrict his thinking to only the approaches in the text. It serves as a guide only.

Jan 1, 1983

By W. S. Versluis, G. W. R. Kuzyk

Atomic Energy of Canada, Ltd. (AECL) is constructing an Underground Research Laboratory (URL), a major component of-the Canadian Nuclear Fuel Waste Management Program. In July 1988. AECL and the US Department of Energy commenced a cooperative research program that included extending the URL shaft by 190 m (623 ft) to the 443-m (1,453 ft) depth. The shaft extension, 4.6-m- diam (15-ft-diam), was excavated by full-face blasting using a burn cut. A Galloway stage accommodated the research activities and the sinking contractor's requirements. Blast designs incorporated controlled blasting techniques to minimize blast-induced damage on the shaft walls. The full-face method has been very effective, with 3.5-m (11.5-ft) rounds being advanced.

Jan 1, 1990

By Andrew F. McKown, Lewis L. Oriard

Advances in explosives engineering are moving forward in several different aspects. These include improvements and new development in explosives products, the application of these products to blasting technologies, and the study of the peripheral effects of the use of explosives, such as ground vibrations and airblast. Topics of special interest in the last several years include new explosives and detonators, cap timing, explosive casting, high-speed photography, perimeter and slope control, air decking and mathematical modeling of blasting processes.

Jan 1, 1988

By Merih Celasun

The literature in operations research centered on mineral exploration has been comparatively limited in view of the significant implications of mineral discoveries upon the national economies in general and mineral industries in particular. Much of what has been published is of somewhat unsure academic nature, indicating to a certain extent the scarcity of industrial applications. Mineral exploration activities present quite difficult operational and conceptual problems. The purpose of this paper is to discuss the principal characteristics of decision problems encountered in planning an exploration program, to indicate an optimization approach to a certain class of allocation problems, and to suggest directions for future research effort.

Jan 1, 1962

By Gregor de Ratmiroff

Field prospecting for bauxite in Venezuela has had a long but interrupted history having till now oferred but evidence of occurrences. The Venezuelan Government, trough the Corporación Venezolana de Guayana (C.V.G.), in 1974, formalized a major effort in prospection for bauxite in the Shield area and the Orinoco Delta in orden to establish the possibility of raw material supply to an upcoming and expanding aluminium industry. The Corporation, in turn, created and delegated to the Division of Geological Stu- dies, the formulation of the necessary infrastructure and execution of work in orden to determine the existence of economically exploitable bauxite deposits.

Jan 1, 1979

By A. G. Journel

The regionalization of tungsten grades at the deposit represents an ideal case for anisotropic hole-effect variogram modelling. The modelling technique is presented step-by-step and the consequences of the model on block kriging are indicated.

Jan 1, 1982

By Glenn Mallory, Margarete Kalin, Ben Romanin

A waste management area of a copper zinc mine which is expected to be generating acid exceeding 1000 years is used as a research facility to develop a passive treatment approach to decommissioning the site. One of the processes proposed to be implemented in a lake with a one million cubic metre volume is biological polishing. To determine the expected performance of the process, model is constructed from experimental data collected in the lake. The model results and the field data represent a weak fit, but the discrepancies are useful indicators of key factors affecting the process, such as iron cycling.

Jan 1, 1995

By M. Stefanakis, M. Errington, A. Kontopoulos, J. M. Prevosteau, K. Adam

The Olympias arsenical pyrite concentrate assaying 25 g/t Au, 40% S, 40% Fe and 12% As is highly refractory in nature; an oxidation pretreatment step is required to liberate gold and render it amenable to cyanidation. In the present study mineralogical analysis techniques including Image Analysis, SEM, EPMA, SIMS, Mossbauer, ICP/MS, etc., have been employed in order to investigate the mode of gold occurrence within the Olympias pyrites. Bacterial oxidation was used as a case pretreatment route and bacterially leached products were examined under SEM. The mineralogical observations and the relevant metallurgical and cyanidation test data were combined to establish a correlation between the mineralogical characteristics of the raw and oxidised products and conditions prevailing over the oxidative pretreatment step and the gold liberation achieved.

Jan 1, 1990

By G. Knight

It is shown that the dust exposure of all underground workers varies greatly from day to day even though each man did the same job in the same working place each day. The variability follows a logarithmic normal distribution with a geometric standard deviation of about 1.6 for the three dust assessments; total respirable dust, respirable combustible dust and respirable quartz dust in both mines studied. The variability was homogeneous for all men and most jobs. The differences between men doing the same job was found not to be significant and it is suggested that the dust sampling program should determine the average for each job and use this as the best estimate of the exposure for each man.

Jan 1, 1980

By D. R. Nagaraj

Literally thousands of new flotation agents, both collectors and modifiers, have been proposed for sulfide and non-sulfide flotation over the past six decades since the beginning of the use of soluble surfactants in flotation. In stark contrast, the number of flotation agents used in practice is small. Xanthates and fatly acids, along with a few well-recognized modifiers, dominate the industry. Three major questions will then arise: a) are there truly specific needs in the industry that call for chemistries that are different from those used currently ? b) if yes, given the track record in the industry, what is the likelihood that such different chemistries will ever be used and to what extent ? and c) is more research into developing new chemistries necessary ? A critical assessment of flotation agents in general is made in this paper to provide answers to these questions and to identify the major factors that are responsible for the large disparity that exists between flotation reagent research and commercial usage.

Jan 1, 1994

By M. J. Virnig, C. P. J. Van Vuuren, A. J. Botha

The Zadra, AARL and organic elution processes and variations of them are presently widely used to recover gold from activated carbon. Despite this the study of the kinetics of elution have received relatively little attention. It is the aim of this study to investigate the rate processes taking place during elution in both inorganic and organic solutions. Batch adsorption and elution rate and equilibrium experiments were performed. The spatial concentration of gold inside carbon particles at various stages of the adsorption and elution processes were measured with a scanning electron microscope using an image analyzer to control and manage the micro-analysis data. The activated carbon particles exhibited film and intra-particle mass transfer rate- controlled behaviour during adsorption in a caustic aqueous solution at 95°C. Elutions in the aqueous caustic acetone solution at 30°C and the caustic aqueous solution at 95°C were unaffected by change in stirring rate. Elution was modelled by desorption reaction rate-control at the outer surface of the carbon particle. Adsorption and elution isotherms under duplicated solution conditions showed reasonable agreement for the inorganic solution and a large disparity for the organic solution.

Jan 1, 1993

By William E. Mead

The process of selecting a building site for a major structure is a complex procedure involving the consideration of a multitude of factors. The approximate geographic location for a structure is usually fixed by its intended function, though often there may be several site alternatives. Socio-economic, logistic, marketing and political factors are the primary site determinants. Also critical in site planning, however, are the environmental factors, both natural and man-made. These factors will influence the precise siting location within the limits allowed by the primary determinants and will dictate some of the basic design criteria. This paper discusses environmental factors, principally those which are natural conditions, that must be analyzed for five different groups of structures. The importance of thorough site environmental analysis based upon the principles of applied earth science is described. Significant elements to be considered in an appraisal of the geology, hydrology, seismology and meteorology are outlined.

Jan 1, 1968

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

Jan 1, 1997

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987