Search Documents

By Alexander Pomerantsev

In recent years, bucketwheel excavators have found wide application in open pit surface mining not only because of their large production capacities, but also because they easily lend themselves to automation. Krupp, Orenstein & Koppel, Buckau-Wolf, Mechanical Excavator, Lauchhammer, Manufacturers in Eastern Europe designed and installed many models of bucketwheel excavators that can excavate any type of materials, could be used in any climate conditions and for any type of technological schemes in open pit surface mining, (Photo I, II and III)

Jan 1, 1979

By Grover H. Emrich

Pennsylvania,, due to its location in the humid east, is fortunate to possess within its borders large quantities of water. Most of the State is drained by three major river systems-the Ohio, Susquehanna and Delaware. This abundant supply of surface water has been widely utilized throughout the State, but today other sources of water must be developed due to the increasing demands for water, die largest undeveloped source of water in Pennsylvania is ground water. Pennsylvania is also fortunate to possess extensive coal resources. These coal resources have contributed measurably to the development and prosperity of the States Coal and water's - two valuable resources - have been necessary for the development and industrialization of Pennsylvania, The State needs both resources but can no longer afford to develop one while adversely affecting or destroying the other, We are aware of the effect of coal mining on surface water, but coal mining can also materially affect subsurface water, This effect will according' to the local geologic conditions.

Jan 1, 1965

By Devraj Sharma

This paper presents technical issues in the design and management of a retorted oil shale disposal site. Major physical and geochemical mechanisms which affect the disposal are: heat transport, moisture migration, chemical species transport, auto-ignition, and mechanical behavior alterations of the retorted oil shale pile. The interaction of these mechanisms and their relative magnitude will affect the environmental behavior of the pile. The paper discusses the coupling between the mechanisms, presents a framework to quantify the processes by laboratory and field measurements, and in addition discusses the use of mathematical models to provide quantitative predictions.

Jan 1, 1981

By J. A. Herbst

Ball mill grinding circuits can be subject to upsets that arise from variable characteristics of the feed ore. These upsets are transients in critical circuit variables such as ball mill mass holdup, circulating load, sump level, cyclone efficiency and product particle size. They may occur frequently so that the operation is continuously fluctuating or they may be of such magnitude that some of the equipment is overloaded, resulting in shutdown, or an undesirable product particle size. The feed ore characteristics that influence ball mill circuit behavior in this manner include the grindability of the ore, the eventual transport characteristics of the ore in the mills and the feed ore size distribution. Control strategies for grinding circuits using conventional proportional-integral (PI) control have limitations to their effectiveness in controlling against feed ore disturbances. The first of these are the interactive nature of two or more control loops on a single circuit. Under some circumstances they begin to fight each other, increasing control error and settling time. PI control loop gain constants can be tuned to give best response for some set of conditions but once these change, as they would with a change in the feed ore, they are no longer the "best" ones (Shinsky, 1967). Due to these limitations, alternatives to conventional PI control strategies have been investigated for grinding as well as other mineral processing operations. These alternatives, all computer-based, include self tuning regulators, decoupling control and optimal control (Herbst and Bascur, 1983).

Jan 1, 1984

By W. C. Dailey

The National Steel Pellet Company is owned by National Steel Corporation, managed by the M. A. Hanna Company and located near the town of Keewatin in northern Minnesota. Annually, the concentrator processes 15.24-Mt (15.0 million It) crude taconite with eight 8.2-m diameter by 5.5-m long (27 ft x 18 ft) wet semi-autogenous (SAG) mills to produce 4.57-Mt (4.50 million It) of iron ore pellets. To improve operating costs and primary mill grinding circuit efficiencies, a task force on liners was formed with the operation, maintenance and engineering staff at N.S.P.C. along with the local supplier of mill liners. Results of the task force recommendations since 1980 along with improvements made in the primary circuit operations, are presented. Mill Liner Design and Metallurgy Changes The primary mill liner task force was formed in 1977. Its function was to improve the operating costs and milling efficiencies of the ten 8.2-m x 5.5-m (27 ft x 18 ft) wet SAG mills that were operating at the time. The SAG mills are driven by two 3500 HP motors drawing a total of 5450 kW at 76% of critical speed.

Jan 1, 1985

By A. Bruynesteyn

Many papers 'have been publihed on the role of the bacterium.Thiobacillus ferrooxidans in the oxidation of reduced sulfur compounds, and years of research have established the following environmental factors, which influence biological oxidation. 1. Oxygen is required for the oxidation of reduced sulfur compounds to the sulfate form. Sufficient oxygen. is available from the air, consequently, it is of importance to get the air to the bacteria. 2. The bacteria are active in the pH range 1.4 3.5. Maximum activity occurs at pH 2..0 - 2.8. 3. -In order to allow the bacterial populations to expand, certain essential nutrients must be available. Nitrogen has to be supplied for the production of body protein, and ammonia is the source most readily accepted by the bacteria. Carbon dioxide is the only utilizable source of carbon and the small amounts available in air are the primary source of this element. Small amounts of phosphate, manganese,, potassium,. calcium. and magnesium are also required. These trace minerals are available from the water and host rock in sufficient quantities. 4. Water is required as a carrier for the oxygen carbon dioxide and other nutrients, as-well as a solvent for the metallic sulfates produced. The bacteria are motile and the water allows the bacterial populations to spread:: bacterial activity ceases if the equilibrium relative humidity drops below 100%. 5.-optimum bacterial activity occurs at temperatures of 34 - 35°.C (93 -.95° F). All activity ceases above 45° C. At lower temperatures, activity its dramatically decreased, but there is still a significant amount at 10 - 11° C.- Thiobacillus ferruoxidans has been isolated from a mine with a year round temperature of 3° C. 6. Unpublished results from our laboratory show that biological leach ore oxidation takes place during the rest periods at the same rate as during the wet leaching periods providing there is a film of moisture remaining around the particles. Optimum conditions can be readily achieved in the laboratory, but application of our laboratory knowledge to commercial leaching dumps is riot as simple. Attempts to achieve improved environmental conditions for the bacteria in leaching dumps would require substantial capital investment and careful planning of leaching operations. This paper

Jan 1, 1972

By W. J. C. Venter

The use of activated carbon to improve the selectivity in the separation of base metal minerals from bulk concentrates played an important role in the development of separation techniques employed at Tsumeb Corporation's Tsumeb and Kombat mines. In this paper the Kornbat mill flowsheet and metallurgical data are given with particular reference made to the separation techniques using activated carbon. The mine's historical background, geology and mining methods are described briefly.

Jan 1, 1973

By Karl A. Olsson

The Glenharold Mine is a surface mine operated by Consolidation Coal Company. The mine is located approximately 90 kilometers (55 miles) northwest of Bismarck, and 3 kilometers (2 miles) southeast of Stanton in west central North Dakota. Glenharold has a nominal design capacity of 3.0 million metric tons per year (3.3 million short tons per year). With the exception of local coal sales, this production supplies fuel for Basin Electric's Leland Olds generating station, a mine mouth power plant. The mine has 175 hourly and 50 salary employees. The Glenharold reserve extends over 210 square kilometers (80 square miles). The mining area is on a dissected plateau between the broad flat Missouri River flood plain to the north and the gently rolling uplands to the south. Erosion by intermittently flowing streams has produced many narrow, steep-walled, drainage ways. Mining begins at the 6 meter (20 foot) cover line and continues to the economic recovery line.

Jan 1, 1982

By J. R. Johanson

In recent years the procedures for functionally designing bulk storage bins and hoppers have evolved from qualitative guess and try methods to a quantative method based on theory and tests of the bulk solid to be stored. This quantative method, developed and implemented by Dr.'s A. W. Jenike and J. R. Johanson as with any new design, must prove its effectiveness and validity in the actual operation of the finished equipment. How accurate are the theoretical predictions? Is it possible to extrapolate from bench size tests on a small ample of the bulk solid to the full scale bin design? Can the theoretical designs be economically translated into working hardware? In this paper the answers to these questions are discussed in light of actual bin operations.

Jan 1, 1968

By Thomas Schultheis, William Heron, Paul Watson, Colin Warren

This paper describes the geology and geotechnics associated with construction of the Thames Tunnel, part of the UK’s Channel Tunnel Rail Link (CTRL). The 2.5km long twin tunnels run beneath the river Thames at depths of up to 40m and are currently under construction. They pass through varying geology comprising alluvium, terrace gravels and chalk with flints and are currently being bored using Herrenknecht mixshield slurry tunnel boring machines (TBM’s). This paper outlines the lithology and engineering properties of each geological formation and describes the geotechnical processes, potential hazards and difficulties experienced in the works. A summary is given into the extent of the investigative work in terms of route selection, tunnel design, TBM optimisation and further details are provided on the geotechnical aspects associated with the construction of the tunnel approach structures and the tunnels.

Jan 1, 2003

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

4.1 INTRODUCTION There have been numerous methods developed for predicting the final subsidence and final displacement profiles (Voight and Pariseau, 1970; Brauner, 1973a; Kratzsch, 1983). But for discus- sion purposes, they can be classified into six categories: theoretical, profile function, influence function, graphical, physical, and numerical modeling. The theoretical method employs mainly continuum mechanics theories and attempts to explain the mechanisms that lead to sur- face subsidence. Many models using nearly all kinds of material behavior have been developed. These include elastic (Salmon, 1963; Berry, 1964), plastic (Pariseau, 1968), viscoelastic (Iman, 1965), and elastoplastic (Dahl, 1969). The Profile Function Method is essentially a method of curve-fitting against the measured subsidence profiles in a particular mine or region. There are more than 20 profile functions developed empirically for nearly all major coalfields in the world. These include, to name just a few representative ones: Hungary (Martos, 1958), Japan (Hiramatsu and Oka, 1968), Russia (Avershin, 1947), United Kingdom (Wardell, 1965), and USA (Peng and Chen, 1981; Karmis et al., 1984). The NCB's graphical method in the subsidence Engineers' Handbook (1975) also belongs to the profile function method. The influence function method was first proposed by Bals (1931/1932). It was further developed in various periods and stages by Knothe (1957), Liu and Liao (1965), Brauner (1973a) and Marr (1975). This method is now widely used in various parts of the world. The physical models include sand (Litwiniszyn, 1959; Pariseau and Dahl, 1968) and gelatin (King and Whetton, 1958; Khair et al., 1986). They are used mainly to study the parameters that control subsidence behavior. The most popular numerical method is the finite element technique. It can simulate nearly every conceivable material behavior, inhomogeneity, bedding planes, anisotropy, and various boundary conditions. This versatility is absolutely necessary considering the ever-changing geologic and mining conditions encountered. In the following sections, only those methods that have been applied to US coalfields will be discussed. Furthermore, the methods for prediction of several key parameters such as maximum subsidence, maximum possible subsidence, and maximum displacement are discussed first, because they are the key parameters to be used in the profile function, influence function, and graphical methods.

Jan 1, 1992

By William J. Halvorsen

We are currently doing work on three ways to improve the performance of our froth flotation systems. One development is the use of a cationic flocculent added to the feed of the froth cells. This does give some improvement in ash of the product particularly in a situation where there is a good bit of clay present. Difficulty is usually experienced with clay carrying over with the water contained in the froth product and also adhering to the coal surfaces. Addition of the flocculent to the flotation feed preferentially flocculates the clay causing it to drop into the tails. The results of some laboratory test work on Pittsburgh 88 Seam coal in Eastern Ohio is shown in Table 1. [ ]

Jan 1, 1979

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By William A. Vogely, DeVerle P. Harris

INTRODUCTION Perspective The phrase "minerala resource appraisal" is widely and loosely used to refer to any quantitative description of a naturally occurring source of fuels, metals, or nonmetals. This leads to confusion when mineral resources are so conceived, for the term refers generically to information on stocks-mineral endowment, resources, reserves, and potential supply-that differ in ways that are important in economic analysis. Mineral resource and other stock measures- these are not flows, e.g., the supply of minerals-have precise technical meanings, which are presented in this paper. Quotation marks are used to separate the nontechnical use of mineral resource from the technical. The term appraisal also leads to some con- fusion because it too is loosely used. When an appraisal employs probability and statistical methods, the appropriate term is estimationb, not appraisal or assessment. This paper presents a conceptual framework or mineral resource information which renders technical, or well defined, relationships of mineral endowment to physical attributes of the earth's crust and earth processes, as distinct from economic values, and identifies estimation approaches that lead to different economic measures of stocks and flows. An important result of this approach is the distinction between the relevance of mineral resource information to economic and policy issues about potential sup- ply (stocks) and dynamic supply (flows across time). With regard to policy analysis, this paper recognizes that mineral resource information has a cost as well as an imputed value. Such a treatment implies that there is an optimum state of resource ignorance, or enlightenment, for a given policy issue and that the relevant economic issue is the selection of that information strategy and appraisal methodology that is indicated by the optimum state. Until the initiation of the OPEC oil embargo, the demand for information on mineral re- sources and potential supply was limited to occasional studies commissioned by Congress or the President of the United States. In these, mineral and energy resources remained loosely de- scribed. When quantitative estimates were supplied, they were not rigorously made, and the estimates and the methodology accordingly escaped close scrutiny. Usually, neither the geo- logical nor economic bases for estimation were carefully described or critically examined. The imposition by OPEC nations of the embargo on oil caused a sudden change in the public and scientific demands for specific 'resource" appraisals, especially of oil and of uranium. These

Jan 1, 1985

By A. Haile, A. Poole

During 2001-2002, the Granny Smith Mine of Western Australia undertook the development of a planned circular failure. Excavation took place in an interim pit wall that intersected the transported sediments, lake clays, and palaeo channel sands that overlay the deposit. The purpose of the study was to refine feasibility level slope parameters used for the initial design of the Wallaby pit, with the intent of increasing the overall slope when excavating the ultimate pit limits. During excavation, the geological and hydrogeological characteristics were studied in detail and data was collected using area-specific instrumentation and monitoring. Failure occurred in mid February 2002, at which time a detailed survey of the excavated slope using laser technology was conducted to provide geometric information suitable for back analysis of the material shear strength. The slope failure and associated information was analysed by geotechnical consultants. The revised shear strength and hydrogeological parameters were then applied to design the final pit walls. The slope redesign provided a cost saving of approximately seven hundred thousand US dollars. Design, slope formation, back analysis, the geology of the clay units, the hydrological environment, planned infrastructure, management and safety issues, and the on-going slope performance of the final slope are discussed.

Jan 1, 2004

By James L. Coburn

Leaching is defined as a form of extraction in which a valuable constituent is removed from a solid body by mass transfer to a solution which, for the purpose of this discussion, is considered to be an aqueous medium. Historically, leaching has been applied to the recovery and purification of many elements. This paper, however, is directed toward the recovery of copper, uranium, vanadium, and precious metals included in the following systems: 1. The leaching of copper minerals, sulfides and oxides, by acid or by ammoniacal leach solutions with or without an oxidant. 2. The leaching of gold and silver, either native metals or as minerals by an oxygen-containing alkaline cyanide solution. 3. The solubilization of certain uranium and vanadium minerals by oxygen or oxidant-bearing lixiviants. Many other systems of this general type exist, but from a production standpoint, these three systems account for most of the major values recovered by leaching.

Jan 1, 1975

By F. Chase, D. Pappas

Pillar recovery has been associated with nearly one third of roof fall fatalities in underground coal mines during the past decade. Safe pillar recovery requires global stability and local stability. Global stability is addressed primarily through pillar design. The local stability risk factors include cut sequence, the final pillar stump, supplemental supports (timbers vs. Mobile Roof Supports (MRS)), roof bolting, and many others. The National Institute for Occupational Safety and Health (NIOSH) has evaluated each of these factors through field research and analysis of accident statistics. The paper discusses design methods and technologies that have been transferred to the mining community and implemented.

Jan 1, 2003

By Mark Leggett, Kevin Roberts

The need to modernise and increase the safety provision of older road tunnels raises challenges in maintaining the operation of the tunnel during such improvement works. The Mersey Kingsway twin road tunnels located in Liverpool UK, constructed in the late 1960s, have had three new cross passages constructed to allow emergency evacuation from one tunnel to the other tunnel and provide safer access for emergency services. The 3200m long road tunnels are lined with an unusual reinforced concrete steel-faced segmental lining with a paint finish. Construction of the cross passages occurred during night possessions with the tunnels returned to normal operation during the daytime. Constructed through water bearing sandstone and lined with precast concrete segments, the passages required advance ground treatment and support works. This paper presents the historical background to the Mersey Tunnels and describes the procurement strategy, design and construction approach adopted for these important safety improvements.

Jan 1, 2003

By John T. Cantwell

INTRODUCTION The process engineer usually is responsible for the design operating philosophy and/or day-to-day operations of a process. Since instrumentation is an integral part of the operation, it is essential that engineers understand the general capabilities of the different types of control equipment available. Many "noncontrol" engineers have become involved with instrumentation for machinery monitoring and control as well as other plant applications. The advent of the microprocessor has led to significant changes in control, both in systems configurations and man-machine interfaces. Today's concept is called simply "distributed control." What is distributed control? Distributed control is exactly what the name implies; the control system is divided into several functional segments and spread out to cover a process. The systems are distributed for physical, functional, and risk reasons. Before delving further into the specifics of distributed control, let's look at the evolution of control systems to see how we got here. Instruments initially were located near measurement and control points in the field. Operators physically had to go to the instrument to change setpoints or take measurements. As processes became more complex, it became evident that a central control area was required. This allowed an operator to monitor and control many variables. The operator's effectiveness was increased dramatically, which resulted in greater efficiency, better quality control, and lower personnel requirements. At the same time, plants became much larger, control applications became more complex, energy became expensive, and the industry became more competitive. All of these factors placed pressure on process and production engineers to get the most for the money. The result was a continuing push to put more instrumentation into a central control room to maximize efficiency and productivity and minimize manpower. This chapter deals in some detail with devices for measuring physical and chemical properties of coal; devices for measuring the weight and weight-rate of flow of coal; devices for the monitoring and control of conveyor systems, solids inventory, fluid flow, liquid level, density, and specific gravity. These instruments have a multitude of uses throughout a coal preparation plant. The discussions cover advancements in "on-line analysis," nuclear control devices, and distributed control using microprocessors, mainframes, and soft-

Jan 1, 1991