Search Documents

By A. R. Przybylek

A fluid bed dryer has been designed for a nonconventional application to upgrade the value of fine anthracite culm and silt recovered from culm banks and anthracite tailings pond beds. This material can be seen as large spoil piles scattered throughout the anthracite coal regions of Eastern Pennsylvania. Engineering of the system commenced in December of 1986 and at this writing start-up is scheduled for late October or early November of 1987. This paper will focus on generalities concerned With system design and operation, and qualify the differences from conventional fluid bed coal drying systems.

Jan 1, 1988

By J. M. Elegante

A belt drive attendant was working underground during his shift at the junction of two belt drives. He worked alone, but communicated with others at the mine by underground phone. At noon his shift foreman stopped by his workstation. At 2:00 p.m. he was contacted by phone by a fellow belt drive attendant. At 5:00 p.m., he was found dead by the oncoming evening shifter.

Jan 1, 1989

By R. G. Robins

The dissolution of metallic copper powder in aqueous solutions of cupric sulfate with ethylene under low pressure was investigated. The reaction stoichiometry obtained was:

Jan 1, 1988

By A. M. Stone

Following the conceptual idea of a Continuous Elution Process early in 1982, the system was successfully pilot plant tested at Western Mining's Kambalda gold plant in December 1982. As a consequence of these tests the Ok Tedi elution ciruit design was changed from batch operation to continuous operation resulting in a reduction in the number of similarly sized elution columns from five operating with one standby to one operating with one standby and halving the process steam requirements. In addition to providing significant capital and operating cost savings the continuous process was simpler to operate than the batch process.

Jan 1, 1989

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

By Y. J. Wang

The ventilation network problem, having both fixed and nonfixed operating points as control devices, is examined in this paper. Emphasizing the concept of solving a system of n equations in n unknowns, this paper presents the generalized problem formulation, some conditions under which the problem does not have a unique solution, and a solution procedure based on the Newton (or Newton-Raphson) method. A numerical example is included.

Jan 1, 1989

By R. W. Guill

For the past five years, Small Mine Development has been involved in the development of small grade underground projects. These projects have been in tough environments where solutions have been found by placing emphasis on creative collaborations by small work forces and selected specialists. This has created an environment where constant innovation and change have become standard operating practice. The cornerstones of these efficient operations have been formed using pneumatic backfill, creative shotcreting, specialized equipment, and highly motivated people. The results realized have served to turn interesting properties into productive operations.

Jan 1, 1988

By H. E. Goetzman

A cooperative research project supported by the taconite industry and the Minnesota DNR was undertaken to establish quality standards for carboxymethyl cellulose (CMC) based organic binders. The objective of this study was to identify the effect of CMC quality parameters such as degree of substitution, molecular weight, and purity as well as the effect of inorganic extenders such as sodium carbonate on performance. These factors have been evaluated by green-ball testing with two taconite concentrates followed by pot-grate tests. Balling tests with bentonite and Peridur were conducted to provide baseline data. At a constant DS the molecular weight as measured by viscosity had the greatest effect on green-ball drop strength. Dry-ball compression strength was most dependent on CMC addition rate and sodium carbonate content. DS was not found to have a major effect on green-ball quality for medium molecular weight CMC.

Jan 1, 1988

By G. B. Michaels

Exploration programs for mineral resources often involve analysis of soils or stream sediments for the mineral being sought or its pathfinders. Because many metals are toxic to microorganisms, patterns of metal resistance in soil or aquatic populations may provide additional useful information at a reasonable coat. These patterns in some cases have been more effective than the soil geo-chemistry and may be easier to obtain. Elevated levels of resistance to silver and its path-finders have been demonstrated in stream populations from an area of known silver deposits, and resistance to gold pathfinders has been demonstrated for gold-bearing areas. Uranium has also been located by this method.

Jan 1, 1989

By A. G. Wylie

The dimensions and shape of both airborne and bulk amphibole-asbestos fibers are different from those of cleavage fragments of the amphiboles. These differences are related to the mineralogical properties unique to the habit of asbestos. These properties include the fibrillar structure, small fibrill widths and distinctive crystallographic faces of fibrills. Criteria for distinguishing amphibole cleavage fragments from amphibole-asbestos include mineralogical proper-ties observable in bulk samples and the dimensions of particles collected on air filters.

Jan 1, 1988

By P. F. Hara, O&apos

Stratabound Proterozoic precious metal mineralization in central Arizona is associated with felsic and adnesitic to mafic volcanic rocks and sediments derived from these rocks. Hydrothermal fluids associated with felsic volcanism form gold mineralization within hotspring vent complexes or within asymetric basins, which flank the vent complexes and are filled with tuffaceous sediments. Massive to semi-massive sulfide copper-zinc systems associated with felsic volcanism may locally contain small gold occurances either laterally or vertically zoned from the ore. In andesitio to mafic rocks, zinc-lead-gold-silver-copper bearing mineralization and gold mineralization are both associated with feruginous sulfide bearing cherts. The partitioning of gold into these specific geologic environments may be related to variations in temperature and composition of the hydrothermal fluid and the depth of the seawater-sediment interface below sea level during the mineralization event.

Jan 1, 1988

By K. O. Johnson

Contaminant transport of mine and mill tailings is controlled by the hydrologic flow regime and the geochemical mobility of the contaminants. Contaminant' mobility is primarily determined by chemical reactions occurring within an interface zone between the tailings and soil The large geochemical differences between tailings and groundwater create a disequilibrium in the groundwater with respect to the soils when seepage from tailings enters the groundwater. Precipitation and dissolution reactions involving the major chemistry occur to return the perturbed system to chemical equilibrium between groundwater and minerals. Retardation of trace elements depends upon the chemical character of the groundwater and the adsorption substrates. In the case of uranium mill tailings, the mobility of contaminants is controlled primarily by precipitation/dissolution reactions which neutralize the pH, modify the Eh (redox potential), and produce highly adsorptive substrate for retardation of trace elements.

Jan 1, 1988

By M. L. Clark

Advances in the recovery of gold from heap leaching are being made daily, but of all the systems vital to the maximum recovery of gold from a leach pile, none is more important than the methods used to construct the pile in preparation for the leaching operation. The technology described in this paper illustrates the latest systems developed to minimize compaction in the pile during its construction and reduce the cost of placement of ore on the pile. The Florida Canyon Mine of Pegasus is evaluated in detail to show reasons for its high degree of success to date.

Jan 1, 1988

By R. E. Greuer

The design of mine fire emergency plans requires that the contamination of mines by fumes, and the mutual interaction of fires and ventilation systems be pre-calculated. Several computer models were developed by the Bureau of Mines for this purpose during the last decade. The models advanced in sophistication from the transient-state simulation of fume concentrations for the early stages of a fire to the steady-state simulation of airflow rates, concentrations, and temperatures for fully developed fires, and finally to the complete transient-state simulation of fires and ventilation systems. The principal features of these models are described.

Jan 1, 1989

By K. P. Pavlich

Strategic planning, including the process of developing competitive strategy, is an integral part of all organizational management; from one person operations to multi-national Fortune 100 firms. The structure of that process varies from decisions and direction based upon one person's intuition to the integration of multiple strategic planning groups from each of a firm's many business units. Everyone has heard interesting strategic planning stories such as the railroad industry's long term failure to realize that they were in the transportation business and not the railroad business, the decision to "give away the razors and sell them the blades", Caterpillar's "SOQ NaP" campaign (Sell On Quality, Not On Price), or the tanker industry's eventual realization that by better managing turn-around the firm could control their largest single cost: depreciation. It is important to remember that very few strategic planning decisions are going to become Harvard Business Review case studies. That fact does not, however, diminish the need for understanding the firm's business, and actively planning how it is going to remain in business in the future!

Jan 1, 1989

By R. R. Klimpel

The process of froth flotation as a means of upgrading the quality of coal by removing ash/pyrite and of separating selected mineral(s) from undesired gangue materials is certainly one of the most common unit engineering operations in use today. Flotation has been successfully practiced at the industrial scale for well over 50 years, and if anything, its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation, as a process, has also shown itself to be an extremely flexible process that lends itself well to a wide variety of solid/solid separations. Thus separations can involve very different particle sizes, particle densities, relative weight ratios of materials to be separated, etc., with surprisingly little modification in equipment and operating philosophy required.

Jan 1, 1988

By Jr. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photo-elastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface and, (3) the effects of subsidence on tension in the truss members.

Jan 1, 1989

By L. W. Laage

Throughout recorded history, underground fires have plagued mining operations. Compared with other hazardous situations in underground mining, a fire can become a global problem by swiftly spreading deadly carbon monoxide and other products of combustion (POC's) throughout the whole mine, often without warning. Experience has shown that when fires are detected and located in their early stages, they are much easier to control and proper escape routes can be more intelligently selected. Recent advances in sensor and data communication technology have made reliable mine fire .detection system installations possible. Unlike building construction. in a mine, it is impractical to install detectors at every desired location. Abandoned workings and unsafe locations preclude sensor installations from both safety and economic standpoints. The net effect is that some fires are detected and located early while the location of others, even if detected early, remains unknown too long for effective evacuation and fire fighting.

Jan 1, 1989

By M. P. Juszli

During the 1980's, a revolution has been taking place in industrial minerals marketing. Transportation deregulation and a handful of creative marketing and distribution managers have completely changed the rules for marketing many industrial minerals. Minerals are being trans-ported much farther than in prior decades and at much less cost. Bulk and package terminals are becoming increasingly common as a means to take advantage of freight rate savings and to provide enhanced service to far-away customers. Water and rail transportation are being used increasingly to penetrate markets considered unreachable Just a few years ago.

Jan 1, 1989

By M. Lotfi

The criteria for evaluating equipment operator performance were identified as the changes in reaction time, the changes in physiological responses, and the changes in subjective reporting of stress. Data were collected while the Subjects operated a front-end loader simulator. This report out-lines the components and the tasks generated by the simulator. It explains the simple and basic assumptions underlying the design of the simulator and the methods of data collection. Improvements that can facilitate the collection of data, including the connection of the simulator to a portable personal computer for on site use are discussed. Statistical analysis of data showed significant deterioration in performance. The report concludes that operator performance can be measured and improved. This report shows that the operator tasks can be simulated by means of simple simulators, the complexity of which is determined by the availability of funds and the area of interest of the investigator.

Jan 1, 1989