Search Documents

By Mark J. Zdunczyk

"The term “aggregate” has a number of definitions depending primarily on the use of the material. Aggregate in some context is sand, gravel, crushed stone, slag or other material of mineral composition used in bituminous and portland cement concrete, mortar, plaster, railroad ballast, filter beds and a variety of other uses where aggregates can be utilized.Of the natural aggregates, crushed stone is widely used for most construction purposes. Crushed stone can be mined from a variety of rock types such as limestone, dolomite (dolostone), granites, and granitic type rocks, basalt, gabbro (trap rock), sandstones, schist, marble, gneiss, quartzite, rhyolite, as well as other rock types. The U.S. Geological Survey (USGS) breaks down the rocks by type sold as follows: limestone, dolomite, marble, calcareous marl, shell, granite, trap rock (basalt, diorite) sandstone/quartzite, slate, volcanic cinder and scoria and miscellaneous stone.In 2015, the USGS estimates that 1.32 Gt (1.45 billion st) of crushed stone were produced in the United States. The volume of crushed stone produced, and the numerous mines that produce it make the crushed stone industry the largest mining industry in the United States. The five leading states for production of crushed stone in 2015 were Texas, Pennsylvania, Missouri, Florida and Ohio. The size of the first two states certainly helps in output because of the large market area. The remaining states benefit from being able to barge along rivers to outside markets in adjoining states. Georgia producers rail large amounts of granitic aggregate to Florida and adjacent states devoid of crushed stone aggregate, especially skid resistant aggregate (aggregate used on the top course of asphalt roads)."

Jul 1, 2016

By J. P. Gliddon, G. C. Wade, J. W. Lill

Since 1980 a number of significant changes have been introduced at Palabora in an effort to offset the effects of reduced product price and increased unit costs of production. These changes and improvements include major equipment rationalization programs, the introduction of trolley-assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives, and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation, and their contribution to cost reduction and improved productivity at Paihbora are considered.

Jan 1, 1987

By L. M. English

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves -pressure losses as negative values and energy additions as positive values -and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at \\tIich the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation net\wrk. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1997

By F. C. Nicolli, J. P. Barbosa, P. S. M. Soares, A. V. Estevez

INTRODUCTION Spent household dry cell batteries are frequently disposed of with metropolitan wastestream (MSW) in landfills where they can leak due to handling or aging. Frequent rain and sun cycles, especially in tropical environments, coupled to the action of leachate, dissolve their metal constituents which will eventually reach rivers, lakes and underground water. It is well known that some of these metals are fundamental to sustain life and that is why living organisms concentrate them through their metabolism, but it has been also recognized that beyond specific limits they can definitely be deleterious to the environment. In other words, high concentration of heavy metals are proven to cause chronic or acute diseases and toxic reactions, by acting on mammals' kidneys, liver and nervous system. In addition, some metals frequently used in household batteries, as mercury and cadmium, are said to be carcinogenic (Landis et al. 1995, Silva et al. 1988). Occasionally, plants to treat MSW are coupled to compost production. Household batteries present in MSW can be dragged into these plants, contaminating their products and eventually reaching vegetables making them not proper to consume by people and animals. Alternatively, batteries are also conveyed to incinerators and burned, throwing into the atmosphere volatile species. These can either act as contaminants as toxic vapor species or be delivered by winds and scavenged by rains contaminating soils and water far away from their source. In conclusion, despite the treatment applied to MSW, one can say that battery residues are potentially environmentally hazardous. The careful assessment of the environmental impact caused by residues of household batteries it is not an easy task and it can be referred as a multivariable problem. First, many different household batteries are produced by industry and the potential environmental hazard associated to their disposal depends primarily on the type of battery and manufacturer's technology. These characteristics will dictate how resistant the battery case is to handling and the

Jan 1, 1998

By Michael Fellows

Epidote is a common hydrothermal alteration product in many copper deposits of the southwestern United States. In many of these deposits epidote, along with calcite and chlorite, generally characterize a distal or halo propylitic alteration assemblage, but the mineral can occur within the central potassic alteration zone as well. Epidote is also a common alteration mineral in deposits formed in calcareous host rocks -- the skarn or pyrometasomatic ore bodies. Within the past 15 years, studies of the major and trace element composition of other alteration phases, principally biotite, associated with base metal ore deposits have demonstrated that some hydrothermal alteration minerals are compositional distinct from their igneous or metamorphic counterparts: However, the use of major and minor element content to identify and zero in on mineral¬ized areas does not appear to be very promising. Little work has been published upon the geochemistry of epidote from this standpoint and the results of my work suggest that a similar conclusion can be applied to epidote. My work (Fellows, 1976) suggests that epidote minerals in hydrothermal alteration suites from porphyry copper deposits in the southwestern United States are generally iron-rich rather than aluminum-rich. As a group, these alteration minerals differ compositionally from epidotes of regional metamorphic terrains. I ascribe these differences to the variations in the oxidation character of the respective environments. However, it appears as though the use of major element compositional variations of epidotes as an exploration tool is severely limited. Epidote is a complex calcium-aluminum silicate. Replacement of aluminum by ferric iron establishes a solid solution series between

Jan 1, 1977

By D. Nebbia, R. Aliberti, F. Solesin

The launch of a Tunnel Boring Machine (TBM) is one of the most challenging activity parts of the construction of a tunnel. Challenges are coming from limited space available, learning curve, concurrence of other activities and in some cases from the geological conditions. Launching a TBM is an extraordinary and complicated operation requiring a great level of planning. The Earth Pressure Balance (EPB) TBM named “Chris” was successfully launched for the Northeast Boundary Tunnel, the largest component of the Clean Rivers Project in Washington, DC. Due to space and time constraints, the 8-meter diameter TBM was launched from a single 20-meter diameter shaft, with a 30-meter-long tail tunnel by means of umbilical connections. This paper presents the steps followed during the TBM assembly and launching to complete the excavation of the initial drive of the tunnel maintaining high level of efficiency and quality despite the space constraints. Specifically, it focuses on the methods and phases used to extract the excavated material (muck) from the TBM and from the tunnel, to supply consumables, precast rings and backfill grout. The paper presents results in terms of productivity, lesson learned and possible alternatives to be considered in similar conditions.

Jun 13, 2021

By M. Yavuz

Due to workability difficulties, people have begun to use iron ore much later than gold, copper and bronze. In addition, iron and steel products are the most commonly used metals which are necessary for human life today. It is a fact that iron ore is raw material of the steel production process as known. Iron&Steel sector is plays an important role in the economic development of countries all over the world. Therefore, the amount of production and consumption of steel is one of the basic indicators of industrialization all over the world. The amount of steel consumed per capita of the country is considered as a measure of development. The world average per capita consumption of steel is around 210 kg in 2007 (Yildiz, 2009).

Jan 1, 2010

By P. -J. Kleiterp

Highwall mining is a mining method to extract coal from a final boundary in open cut mining, trench mining or contour mining. This boundary may have been reached because of economic constraints (economic strip limit) or geographic constraints (spoil heaps, rivers etc.). Coal is mined from visible, horizontal, or near horizontal coal seams by making rectangular, parallel, unsupported drives with an unmanned cutterhead and coal transport system. This is controlled from a mining unit, or launch frame, positioned outside the drive, in front of the highwall. Removal of overburden is not required or is limited to small quantities only. Highwall Mining originated in the 1940 in the Appalachian Coal Field. This paper describes the history of the various machines that have been designed for highwall mining. During the 1990 and later, there has been more emphasis on the safety in highwall mining. Many pillar strength formulae have been derived to determine the required width of pillars in highwall mining and, with that, the economic feasibility of highwall mining. The various pillar strength criteria will be discussed in this paper showing the countries where they are applied. In order to make highwall mining equipment safer and more productive, there have been quite some technological improvements applied to the machines. These technologies make highwall mining ready for the future as a serious mining method, also outside its traditional Appalachian mining area.

Jan 1, 2010

By W. A. Van Dyk

Hydrophobic particles with diameters between 1 and 3 mm are poorly recovered by conventional flotation techniques. A novel reverse flotation technique is described whereby coarse particles with surfaces rendered highly hydrophobic, repel the bubble films in a froth and thus drop through the froth under gravity, to be recovered as a sink product. Conversely, gangue or hydrophilic particles are supported by the bubble films in the froth and are therefore recovered as a floating product. Tracer tests were conducted in the cell in order to study the dynamic behaviour of solid particles in the froth. The effects of hydrophobicity, density, particle size and particle shape were investigated experimentally. The higher the hydrophobicity of the particles, the lower the recovery of particles as a floating product, while the recovery of particles as a sink product increases with an increase in particle density. Furthermore, a decrease in particle size results in an increase recovery of hydrophobic particles as a floating product. When treating particles of the same mass-to-surface-area ratio in the froth, flat particles would be recovered as a floating product in preference to cubic, disc-shaped, cylindrical and spherical particles, in that order.

Jan 1, 1995

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles) northeast of Winnemucca, Nevada. The deposit is owned by First Miss Gold Inc. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 m (1 400 ft.) to 671 m (2 200 ft.), along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate within the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By Gabriele Eccher, Michele Caponero, Paolo Cucino, Roberto D’Angelis

"This paper describes the optic fiber structural monitoring system implemented for Pavoncelli Bis tunnel. The paper highlights the optic fiber sensors customization capabilities, how they smoothly fit precast concrete lining processes and TBM operations, and how a lifelong service monitoring can be achieved. An overview of readings’ evolution during excavation concludes the paper.INTRODUCTIONPavoncelli Bis is a 10 km hydraulic tunnel designed to by-pass the existing Pavoncelli tunnel which experienced severe damages during the 1980 Irpino-Lucano earthquake, in south of Italy (Barla 2009). Pavoncelli Bis excavation work commenced in 1988-90, however, when excavation approached pk. 0+583 in 1992, water percolations became more and more consistent and resulted in work suspension. The tunnel was eventually sealed at pk. 0+383, leaving a flooded section between pk. 0.383 and pk. 0+583. Work resumed in 2012 where EPB-TBM excavation was adopted to cross the flooded section and to overcome complex hydro-geological conditions in various lito-types and, in particular, in the Varicolori Clay-shales area (Figure 1).Consequently, stress evolution monitoring is extremely important during construction and during the service life of tunnel lining in clay-shales and in faults areas. In particular, the paper focuses on the monitoring system proposed for the newly EPB-TBM excavated portion from pk 0+583 onwards where optic fiber sensing technology was chosen for its reading stability and reliability in presence of water and its ability to be connected in series and remotely interrogated at kilometers of distance. FBGS OPTICAL FIBER SENSOR TECHNOLOGYFiber Bragg Grating Sensors (FBGS) are gaining increasing attention in the field of experimental stress analysis. Basically, Fiber Optic Bragg Sensors are strain-measuring devices and therefore provide many of the advantages of the well-known metal foil strain gages (Kreuzer 2007).Bragg gratings are written into so called single-mode fibers. These fibers consist of a very small inner core of 4 to 9 µm diameter and an outer part (cladding) of pure glass (SiO2) of 125 µm diameter. The difference of refraction indexes between inner core and cladding causes the light to propagate only inside the small core."

Jan 1, 2016

By J. M. Cases

Diffuse - reflectance Fourier - transform infrared spectroscopy, Hallimond tube flotation and microelectrophoresis have been utilized to investigate the reactions involved in the adsorption-abstraction of K-amylxanthate on finely ground galena and pyrite. In order to work under well-controlled conditions both minerals were wet ground in a specially built laboratory stainless steel or iron mill. Four surface products were found to be formed on galena: monocoordinate lead xanthate, non-stoichiometric lead xanthate, dixanthogen, and amyl carbonate disulphide. Only dixanthogen was observed on pyrite after using stainless steel rods, while ferric iron xanthate was found when iron rods were utilized.

Jan 1, 1989

By M. E. Lewellyn

A lower moisture content for a clean coal product means increased Btu content, or increased yields at the same Btu content, and lower operating costs. The conventional surfactant-based dewatering aids effeciently lower the moisture content but often the presence of residual surfactant in the filtrate and recycle water causes problems downstream. ACCOAL-DRI 1000, a surfactant-based dewatering aid, was developed to solve this problem by minimizing the downstream effects while efficiently lowering the moisture content. The theory of the use of surfactants in filtration will be discussed as well as the development and field evaluation of this new product.

Jan 1, 1988

By Nathan Bowersox, Zuzana Skovajsova, David M. Jurich, Brian Harris

When unwatered after more than 50 years of operation, the White Rock Tunnel of the Upper American River Project in the foothills of the Sierra Mountains exhibited failing rockbolts and ground falls. Repairs designed for the 5 mile-long, 24-foot horseshoe unlined hydropower tunnel included pattern rock bolts, shotcrete, and cleanout of the rock trap. The work, originally scheduled for two 3-month winter outages, was completed under challenging conditions in a single 4-month outage following a carefully sequenced work plan using robotic shotcrete and rockbolter machines. Flexibility, creative solutions, and collaboration by all parties were key to project success.

Jun 13, 2021

By Howard L. Hartman

If I told you tonight at the outset that my prognastications for the future of mine ventilation were imparted to me by a palm reader or inspired by a vision, you'd dismiss what I had to say before I said it! If, on the other hand, I told you that my forecasts were the result of an elaborate computer model, derived from a complex algorithm, which in turn relied on finite element analysis -- and the entire projection confirmed by on-site experiments with a turbo hybrid-flow mine fan -- you'd sit up in anticipation and hang on my every word!! All of which places me in a terrible dilemma, because my predictions really lie somewhere in between. My intent is to talk to you out of my background of forty years in mine ventilation, looking ahead to conditions that I expect to prevail in the next fifteen years. You may be curious why I picked an unlikely time span of 55 years for my overview, and my response is that it bridges a career lifetime. "The last forty", of course, corresponds with the period of my professional employment since graduating with a B.S. and M.S. here at Penn State. "The next fifteen" bridges the period I expect (the Lord willing) to remain professionally active -- and coincidently brings us into the beginning of the 21st century. (I must confess to stacking the deck a bit: Since it's infinitely harder to look ahead than to look behind, I purposely minimized the forecast period and maximized the history! Besides, "forty" and "fifteen" have a nice phonetic ring, perfect 20/20 vision sums to "forty", etc., etc.). With these disclaimers, I'll invite you to join me now in a fast 55-year overview of mine ventilation, of necessity limited to a broad-brush treatment of the subject. (After all, this is an after-dinner talk, not a marathon!) In each- segment, I've selected the seven topics that seem to me of paramount importance: in the first part, seven accomplishments in retrospect, and in the last, seven expectations for the future. (The number "seven" needn't confound you, either: In the bible, it signifies "wholeness" or "completeness".))

Jan 1, 1987

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

The process of designing pillars and selecting support measures in underground coal mines relies highly on the accurate assessment of mining-induced loads and the load-bearing capacities of the supports. This study proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology.

Jun 1, 2023

By Hazal Melis Aytac, Lana Alagha, Fardis Nakhaei

Gallium (Ga) and Germanium (Ge) are essential strategic elements that are extensively used as semiconductors in many technological fields. Owing to their essential uses and supply disruption, Ga and Ge are deemed critical by the U.S. They are typically found as substitutions or inclusions in zinc minerals. However, their distributions within zinc minerals are not well understood. To address this, trace element and mineralogy analyses of representative samples obtained from an old high-zinc-grade tailing were performed using various qualitative and quantitative techniques. These techniques included Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Tescan Integrated Mineralogical Analysis (TIMA) with Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Moreover, bench-scale froth flotation tests were conducted to enrich zinc minerals, the major hosts of Ga and Ge, using PAX as a collector, Na2S as a sulfidizer, Pb(NO3)2 as an activator, and MIBC as a frother. Comprehensive characterization analyses of the flotation products showed significant enrichment of Zn, Ga and Ge in the flotation concentrates.

Feb 1, 2025

By Danforth R. Hale

The pressure of military use of quartz resonators led to efforts to Grow high, grade quartz crystals in Germany and in Great Britain during 19)3-25, and was responsible for a series of U.S.A. Signal Corps contracts beginning in 1946 with the Clevite Corporation (as the former Brush Development Company), Bell Telephone Laboratories, Antich College, and others. The technique of growing crystals from the melt, such as KI, NaBr, was already commercially inuse Quartz could not be so grown, since its utility depends on the form stable below 573°C, and, even if it could be grown from an extraordinarily viscous melt, the higher form passing through this transition becomes twinned. Again, several crystals were being grown commercially from water solutions; quartz, however, is listed in the common literature as being insoluble in water. Fused quartz, or vitreous silica, was chosen as raw mater¬ial by the European experimenters because of its thermodynamically lesser stability than quartz, and various alkaline solutions were tried for the purpose of enhancing the solubility.

Jan 1, 1964

By C. Rodriguez, T. BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle. Blasting is the first and lowest cost per ton stage in the comminution value chain. The basic principle that effective blast design can optimize fragmentation from the Run of Mine (ROM) ore muck pile to improve productivity through digging, loading and crushing to grinding and increase mine site profits has been well documented. Benefits of controlling fragmentation in the blast include reduced wear on equipment, faster loading, increased truck loads while detecting oversize rocks at the muck pile can reduce the frequency of a blocked primary crusher. A second basic principle is a measure of particle size distribution (PSD) at each unit operation in the comminution cycle allows engineers to manage blast design to produce fragmentation in the ROM ore most suitable to optimize downstream unit processes to improve mine site productivity and profits. Split-Online® systems have measured PSD of rocks on conveyors from the primary crusher to the SAG mill for over 20 years. Split-Engineering partnered with various mining companies to develop Split-ShovelCam® to automatically measure fragmentation from shovels and excavators working the ROM muck pile. This paper takes the reader “Back to Basics” by discussing the use of real time fragmentation analysis at the muck pile as an important parameter to optimize energy factors required for each blast. Case studies are given. INTRODUCTION The basics of mining are: • Explore for and find economic resources of valuable minerals • Mine rocks containing valuable minerals using blasting • Crush and grind rocks to liberate valuable minerals (comminution) • Recover valuable minerals for sale Comminution is an energy intensive process which accounts for a major proportion of mine site costs. Effective blasting can improve comminution and deliver significant reductions to mine site unit costs, (CEEC, 2016). Engineers, scientists, builders and even philosophers have long promoted the phrase “measure to manage”; the premise being “you can’t improve what you don’t measure”. Blast Engineers measure fragmentation in ROM ore for feedback to manage energy input in the design of blast patterns to optimize the ROM product size for downstream operations, whether they be for ROM Leach or feed into the primary crusher.

Jan 1, 2019

By Robert F. Randolph

New technologies confront mining organizations with unprecedented human factors challenges. Likely problem areas range from the design of the human- machine interface to the design of work groups and mine organizational structures. However, these human design considerations are commonly ignored in most industries, resulting in a failure rate of 75% for advanced technology programs. The U.S. Bureau of Mines is addressing these concerns through a program of research on the human side of high technology mining systems. Interviews with mining industry participants and researchers have identified concern in several areas, including training and equipment design. Although new mining technologies promise to improve overall safety by relocating miners away from hazardous areas, data from MHSA accident reports and other sources suggest that certain types of new hazards may be created. Many of these new hazards can be reduced though a systems approach to ergonomic design of equipment, tasks, and work processes. This evidence, combined with reviews of high technology human-machine systems in other industries. can help in the design of safe and efficient future mining technologies.

Jan 1, 1992