Search Documents

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and MPSI merged, a unique opportunity occurred for two independent mill fabricators to compare various design procedures and the research upon which they were based. This paper documents such a comparison in the structural design area. Several SAG mill analyses are compared using both Boliden Allis and MPSI methods. The differences and similarities are then utilized in a correlation of critical stress definitions and the acceptable design and inspection criteria.

Jan 1, 1992

By Thomas H. Koenning, William E. Bruce

Determination of the state of a mine fire is an important function during firefighting and during rescue and recovery operations. It is imperative that an accurate, up-to-date assessment of fire conditions be available for persons directing such activities in order to avoid unacceptable risk to mine rescue teas and/or fire fighters. Many indicators which consist of ratios of the concentrations of fire gases have been developed over the years for determining the state of a mine fire. Results from numerous gas sample analyses are necessary for determining the trend of the fire. Some indicators are preferred because the influence of sample dilution, a frequent problem, is said to be eliminated. Definitions and examples of indicator6 found to be useful in diagnosing recent western U. S. coal mine fires are presented. Mine gas explosibility is an important subject also requiring rapid assessment. Example explosibility calculations are presented applying one widely used method. Establishing limits for withdrawal of personnel are discussed.

Jan 1, 1987

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999

By C. Patrick

Annually, the U.S. coal industry generates and must dispose of over 200 million tons of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks, used for under-ground ventilation stoppings, with refuse blocks. Refuse was collected from three active preparation plants in Eastern Kentucky and used as the primary aggregate for concrete cylinders. The refuse fell within ranges normally observed for size consist, moisture, and ash. Stress-strain analyses yielded compressive strengths of the refuse cylinders from 59% to 77% of the control group strengths. Low variability within groups while significant differences between groups were found. On-going determination of effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1995

A Mark IV surface force apparatus (SF A) was used to conduct direct force measurements in dodecylamine hydrogenchloride collector solution between mica surfaces at varying pHs. It has been found that the long-range hydrophobic forces reach a maximum at pH 9.5, which also corresponds to the maxima attained by the contact angle and flotation recovery of quartz. The charge densities are comparable on both mica and quartz surfaces (0.40-0.48 run2), making it possible to draw conclusions on the flotation of quartz from the direct force measurements conducted on mica. Therefore, it may be suggested that the maximum flotation recovery of quartz m the range of pH 8.0-10.3 may be attributed to the appearance of long-range hydrophobic force, which in turn can be related to the formation of a close-packed monolayer (or hemimicelle) in the presence of neutral amines formed as a result of hydrolysis.

Jan 1, 1996

By Steve Kral

The former mayor of Los Angeles, CA is a believer in public transportation but thinks neither his city nor the entire country is spending enough on basic infrastructure. In fact, the United States has fallen behind most other developed nations in improving public transportation, the former mayor said. Antonio R. Villaraigosa was the keynote speaker at the North American Tunneling (NAT) conference, held June 22-25 in Los Angeles, CA. The event, held every two years, is sponsored by the Underground Construction Association of SME (UCA). This years? conference attracted 1,091 underground construction professionals from around the world. The accompanying exhibition continues to grow, attracting 142 exhibiting companies occupying 162 booths. As always at NAT, registered attendees received the proceedings volume of the conference, which contains 132 papers. The proceedings volume, including a CD of the papers, is available from SME for $149 member, $139 student member and $189 nonmember. The book can be ordered from SME, NAT item #400-4, phone 303-948-4225, 1-800-763-3132, or online at www.smenet.org/store.

By C. R. Kuhn

From 1968 to 1975, most work in surface modification of inorganic materials involved silane coupling agents. A silane coupling agent can be described simply as an oganosilicon chemical having a general formula RSi-X3 wherein the R group is attached to a silicon in a thermally and hydrolytically stable manner, and X is a hydrolyzable group usually having an alkoxy functionality. About 1975, Kenrich Petrochemicals brought into the market place titanate coupling agents. Titanate coupling agents usually consist of one alkoxy group and three functional groups attached to a central titanium atom. Zircoaluminates became available in about 1982. Zircoaluminate organometallic coupling agents, which vary principally in their respective organofunctionalities, arise from a basic technology in which two different types of organic ligands are selectively bound to a low-molecular weight zircoaluminate backbone.

Jan 1, 1995

By Joseph F. Shirley

A froth flotation plant to recover by-product molybdenite must be designed specifically for the selected separation process and the type of ore being treated. However, some general rules concerning by-product molybdenite plant design can be suggested that would be valid for most processes. The term by-product molybdenite in this paper is limited to the recovery of molybdenite from copper porphyry ores, which essentially amounts to selectively separating molybdenite from copper and iron sulfide concentrates. In addition, most of the discussions would apply only to the almost universally used approach of floating the molybdenite and depressing the copper and iron sulfide minerals.

Jan 1, 1979

By Robert A. Westin

Polychlorinated biphenyls (PCBs) are a group of chlorinated chemicals that were used in many different fire resistant hydraulic fluids, heat transfer fluids, and in electrical equipment as dielectric liquids. PCBs were manufactured primarily by Monsanto Chemical Company under the tradename Aroclor, and were used by many different electrical equipment manufacturers. PCBs are noted chiefly for their extreme chemical inertness. This resulted in exceptional fire resistance and long life in applications involving exposure to high temperatures and intense electrical fields. This combination of properties resulted in PCBs being widely used in electrical equipment used in mines, including transformers, capacitors, and some electric motors. PCBs were also used as working fluids in some heat transfer and hydraulic sys terns. The same chemical resistance that gave PCBs long life in industrial applications give PCBs essantially eternal life when they are released into the environment. PCBs are not highly toxic in the sense that exposure does not cause immediate health problems. However, PCBs accumulate in the human body and neither degrade nor are eliminated from the body, and long-term exposure to PCBs can result in changes in liver function which may increase susceptibility to the carcinogenic effects of other chemicals. PCBs also accumulate in the food chain; the concentration of PCBs in fresh water fish may be several hundred thousand times as high as in the water the fish are taken from.

Jan 1, 1981

By Peter L. Dunn

With the advent of new high-strength magnetic materials, rare-earth magnetic separators have become more common place for processing heavy mineral sands. In many instances, rare-earth magnets have replaced conventional separators such as electromagnetic cross-belt and induced-roll type machines. This paper will present the results from a detailed test program developed to evaluate the performance of rare-earth drum and roll separators for processing heavy mineral sands. The effect of machine design parameters, such as magnetic element configuration and separator diameter, will be reviewed in light of these test results. The impact of basic operating parameters (i.e. feed rate and roll speed) on separation efficiency will also be presented.

Jan 1, 1999

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

Tellurium (Te) is an important scattered metal. Known as the vitamin of modern industry, national defense and cutting-edge technology, it is the supporting material for new high-technology materials. Currently, its separation and extraction from Te-bearing materials face problems such as long flowsheets and high reagent consumption, giving rise to an urgent need to develop new methods for its recovery.

By D. F. Cater

The Macassa Mine is a mature mine with a 61 year history of continuous production. The majority of past production has been derived from a zone called the '04 Break (Main Break). Recent underground mine exploration has been successful in locating several neighbouring ninera1ized zones. This paper will characterize the spatial location, geometry and mineralogical properties of these secondary zones. Future plans for underground mine exploration to follow-up on these target zones will be outlined.

Jan 1, 1995

By Emily Muto

LiDAR technology has made it possible to map large areas of underground mines accurately and rapidly in three dimensions. MSHA Technical Support began implementing LiDAR technology in conjunction with the Agency’s Pillar Collapse Initiative, using scans to determine width-to-height ratios (w/h) of pillars adjacent to mass collapse areas and to conduct risk assessments for global pillar stability in U.S. stone mines. This work quickly expanded to include change detection, such as measuring many pillars to show which are deteriorating over time. Change detection has also been used in ground falls and squeeze areas to see if they have continued to propagate. LiDAR technology supports accurate data acquisition of unstable mining conditions from safe distances. For example, once the LiDAR scan has been processed, it can measure roof fall cavity heights and volumes with the user at a stable ground location. Some LiDAR scanners can collect geologic data, such as joint orientations.

Jun 25, 2024

By D. Hodouin

The paper reviews approaches to estimate in a real time fashion consistent mass flowrates and assays, using data from the on-stream analyzers and flowmeters of a flotation circuit. Results obtained with one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1996

By A. D. Davis

The disposal of spent ore from cyanide heap-leach processing facilities is of concern to the mining industry, regulatory agencies, and the public. Disposal of several hundred million tons of additional spent ore is planned in the western United States during the next decade, with increased amounts likely if gold prices rise. In the past decade, more than fifteen million tons of spent ore have been disposed of in the Black Hills. South Dakota's off-loading criterion for cyanide has been set by the state's Department of Environment and Natural Resources at 0.5 parts per million (ppm) as weak acid dissociable (WAD) cyanide. Nitrate off-loading limits vary for each mine in the state, depending on ore type and other factors. Nitrate concentrations in leachate from spent ore depositories could be caused by conversion from other nitrogen-containing species. One likely source of nitrate is residual explosives from blasting of ore. Previous work on the combustion products of nitrogen explosives has shown incomplete 3xidation (Johansson and Persson, 1970). Another likely nitrate source is degradation of cyanide to ammonia, followed by oxidation to nitrite and nitrate.

Jan 1, 1994

By Lynn B. Hales, Randy A. Ynchausti

Because of the high economic value associated with small improvements in the operating performance of mineral processing plants, innovations in instrumentation, stabilization and expert control systems have been an ever-present part of the landscape in plants throughout the world since the I 960s. Expert control systems are computer programs that continuously monitor plant conditions; contain "expert knowledge" concerning the process, equipment and operational knowledge; and make timely recommendations for new process set points or even directly change the process set points to achieve desired management goals. Early rudimentary expert control systems first appeared in the early 1970s. They have grown from small, experimental but ambitious projects in which single unit operations were controlled to plant-wide systems that include technologies used in the U.S. space shuttle program. Experiences and results of applying these systems throughout the world will be explained discussed and analyzed. Typical results will be outlined and the use of expert control in the future will be projected.

Jan 1, 2000

PT Freeport's Mine in Irian Jaya, Indonesia uses a number of 500m long vertical ore passes to transfer ore from the open pit to the mill. The current tonnages moved are in the order of 125 ktpd and this will be increasing to 240 ktpd. This amount of falling rock generates high pressures in the ore bins, when ore feed is terminated the pressure is no longer constrained resulting in back blasting of materials and air up the ore passes. Three methods were tested to try and eliminate or reduce this problem; recirculation of the entrained air, widening of the orepasses and relieving the pressure of the back blast. The final method proved to be the most effective in the short term. As a long term solution the orepasses are currently undergoing widening.

Jan 1, 1998

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Secondary blasting requirements have varied from one shot per 27 tonnes (30 tons) to one shot per 900 tonnes (1,000 tons) of ore. Geology, structure, cave abutment loads, and location of the ore in the column all affect the amount of oversize boulders (greater than three-fourths cubic meter or one cubic yard) that require secondary breakage. The primary method of breakage utilizes cone charges (plastic funnels filled with an emulsion) placed on accessible oversize rocks. Hangups in the brow area of the drawpoint are drilled with a self contained diesel hydraulic drill and loaded with gelatin dynamite. High hang-ups located beyond the reach of the secondary drill are "bombed" in with strategically placed emulsion bundles or ANFO bags loaded in place though a sectioned aluminum pipe.

Jan 1, 1994

By B. C. Lewis

When John F. Kennedy made this statement, I am sure he was not thinking about the valuation of limestone reserves. However, it is certainly applicable. The objective of this paper is to demonstrate how the discomfort of thought (i.e., the analytical and methodical process performed by a reputable professional) builds the foundation for an opinion that provides assurance as to the value of a property. In its final form, a valuation is nothing more than an opinion. The credence of that opinion is directly proportional to the knowledge of the appraiser and the efforts and judgment extended in developing said opinion. Presented herein are the methodologies for formulating a defensible opinion. Before detailing the valuation process, an overview of the limestone industry is presented along with some historical parameters relating to the industry. Secondly, the most widely used valuation methodologies and a brief discussion of each are presented. Two case studies are then presented, which review actual valuation studies. The paper concludes with how the valuation process should be published in a report format that is defensible from a legal standpoint, bankable from a financial standpoint, and decipherable from a layman's standpoint.

Jan 1, 1989

By K. Eric Livo

The Front Range Infrastructure Resources Project (FRIRP) of the U.S. Geological Survey (USGS) is currently using Landsat Thematic Mapper? and air- borne-visible-infrared-imaging-spectrometer (AVIRIS) data along with planned thermal-infrared data and interferometry-synthetic-aperture radar (IFSAR) data to assess the industrial-minerals quality and quantity along the Colorado-Wyoming Front Range Urban Corridor and to characterize surrounding areas. Landsat? satellite data show synoptic views of the corridor, which may readily be used to identify potential regions of permissible terrain, such as river drain-ages, pediment surfaces, upturned lithology, and bed- rock exposures, where various types of deposits may occur. Descriptive models of these deposit types are used to define the physical features that need to be recognized and characterized. In the case of Landsat? data, the measured light is either reflected or partly absorbed by surface materials, depending on the wave- length of the light, which allows coarse mineral classifications to be made.

Jan 1, 1999