Search Documents

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By F. Calizaya

A booster fan is an underground ventilation device installed in the main airstream to handle the total quantity of air circulated to one or more working districts. It is installed in a permanent stopping and equipped with airlock doors, a monitoring system and interlocking devices between the main fan and the booster fan. When adequately installed, a booster fan can be used to reduce the main fan pressure, reduce leakage and decrease the power consumption. However, an inadequate installation can increase the likelihood of mine fies and recirculation of air contaminants. This study identifies hazards associated with the operation and maintenance of booster fans. It analyzes the accompanying risks and recommends control measures to reduce those risks to acceptable levels. The ventilation network of an existing coal mine was updated to include a booster fan. The hazards associated with the operation of this fan were identified, the risks analyzed and the esponse to each failure mode established.

Mar 1, 2014

By Dennis P. Bryan

Natural lightweight aggregate may be defined as inherently low density natural mineral materials. In most all instances they are relatively young volcanic rocks which, because of their geologic environment, are limited to the Western U.S. These Tertiary and Quaternary volcanics are low-density glass and vesicular material including, but not limited to, pumice and volcanic cinder. The distribution is widespread throughout the West with the principal producers being New Mexico, California, Oregon, Idaho and Arizona. The primary user is the construction industry where weight reduction equates to cost savings. Principal products in which natural lightweight aggregate is utilized because of its lower density include lightweight portland cement concrete and lightweight concrete masonry units. In addition, due to location, some natural lightweights compete with normal weight constructions aggregates for uses such as road base and common backfill material.

Jan 1, 1989

By M. Rodgers

Dow Water & Process Solutions (DW&PS) was approached by ASARCO Inc. to attempt to recover cobalt and copper from their copper solvent extraction (SX) raffinate. Cobalt is added to many copper electrowinning tankhouses to help to prevent lead electrode corrosion. With cobalt?s high price this can be a large expense. ASARCO has ore that contains a small amount of naturally occurring cobalt. Currently they have no way of capturing this high value metal from their leach or raffinate streams. DW&PS has some chelating resin technologies that should be able to help solve this problem.

Jan 1, 2010

By Lothar Anheuser

The appearance of very large shielded softground TBM's, of 14 m (46 ft) O.D. and more, as needed for two-lane highway tunnels, calls for a thorough search of overall stability and new solutions for front support during maintenance operations in the cutting chamber. The paper deals with the development of a shield for the planned 4 th tunnel crossing under the river Elbe in Hamburg. Specific problems arise from the high water head, the shallow overburden of loose soil and the stone-bearing mixed ground. The choice of the tunneling method and the different features provided to overcome the problems are discussed.

Jan 1, 1995

By Charles Kocsis, Pedro Nascimento, W. Patrick Arnott, Samuel J. Taylor

Respirable crystalline silica (RCS) is an inhalation health hazard for mining and industrial work environments and must be monitored. We provide theoretical analysis of real-time measurements for determining RCS mass concentration without the use of filters by using photoacoustic spectroscopy. The suspended dust in the mine air can be continuously sampled by the photoacoustic instrument. A tunable quantum cascade laser is the light source, allowing for determination of interferences such as kaolinite, coal dust, and water vapor. The most useful spectral region is found to be between 11 and 13 μm. Absorption by water vapor, and, to a lesser extent, carbon dioxide, in this spectral region has gaps that allow for quantification of the aforementioned dust species as well as a convenient check on the calibration of the instrument. This work brings photoacoustic measurement of aerosol to the mid infrared range where spectrally dependent light absorption can be used to quantify dust composition and mass concentration.

Jul 31, 2022

By Joel Lenz, Warren Hood, Jackson Jenkins

Whole ore or other process streams are being transported from mines to remote processing facilities for multiple reasons, such as improved project economics, maximum utilization of capital, and minimization of environmental risk. Case studies will be presented from a variety of operations. Glenbrook Nickel processes ore from their deposit and receives ore from New Caledonia, crushes and dries the ore, and transports it inland to the smelter. The Mule Canyon and Rosebud ore bodies truck-haul their ores to the Lone Tree and Twin Creeks processing plants. Pegasus Gold hauls their Diamond Hill ore to their Montana Tunnels facilities, and Sierrita pumps solution to an existing tank house 8 miles away for electrolytic recovery.

Jan 1, 1998

By David Morrison

"The history of the mining industry is littered with in-pit crushing and conveying (IPCC), which should not be confused with the International Protocol for Carbon Capture, projects that failed. The failure is not the technical one of “did it achieve the desired tonnage rate for a longish test period” but, rather, the far more important one of “did it provide return on the investment in the manner that was promised?” While quite a few can claim the former, very few system installations can claim the latter.The reasons for the many failures are numerous, but they are all characterized by a combination of an element of engineering optimism in any, or all of the production rates, the productivity, or the operating and maintenance costs and in predicting the continuity of operating conditions. In these days of big data, propagating such a situation is rapidly becoming unforgivable.In this article, the three most common scenarios put to the corporate board for approval, and the logic as to why they were selected, are examined (with the irony included intentionally).• Fully mobile crusher, fed by a shovel and conveyed out of the pit to a waste dump / process plant.• Semimobile crusher (much more expensive than a fixed crushing station but which apparently allows trucks to short haul inside the pit and improve productivity), which moves when the face moves.• Relocatable crusher (more expensive than a fixed crushing station but which gets relocated at great expense after all the fixed infrastructure impeding relocation is demolished) fed by trucks that don’t leave the pit mostly.This paper will also consider the truth about their operational performance and associate costs."

Dec 1, 2016

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018

By R. L. Eppley

The Blacklick Creek Watershed Association was awarded a $158,000 Growing Greener grant from the Pennsylvania Department of Environmental Protection in 2002 for the design and construction of a sulfate reducing bioreactor (SRBR) cell to treat acidic discharge from the Judy 14 abandoned underground coal mine near Indiana, PA. The vertical flow SRBR was designed to treat 38 liters per minute of MIW containing elevated concentrations of aluminum and iron. Other treatment systems at this site plugged due to aluminum precipitates; this problem did not occur in the SRBR. The bioreactor has been periodically overloaded with flows up to six times the design rate. To date, the only maintenance performed on the unit has been the addition of hay to the surface of the unit in response to less than expected performance. The periodic hay additions appear to have restored the SRBR to nearly post-construction levels. Since construction, the SRBR has treated about 136,000 cubic meters (36 million US gallons) of MIW.

Jan 1, 2010

By Larry D. Patts

Section 317(e) of the Federal Coal Mine Health & Safety Act of 1969 directed the Secretary of the Interior to prepare standards under which all working places in a mine shall be illuminated by permissible' lighting while persons are working in such places. Section 317(e) further provides that such Working places shall be illuminated within 18 months after such standards are promulgated. In accordance with this section of the Act, there was published in the Federal Register for December 31,1970 a notice of proposed ru1emaking which prescribed the illumination to be provided in the working p1 aces of underground coal mines. In 1ight of written comments, suggestions, and objections to this proposed ru1emaking, the proposed standards were with-drawn and reproposed in the Federal Register for Wednesday, October 27, 1971. In light of further comments, suggestions, and objections, a public hearing was held on April 4, 1974 and standards were again reproposed and published in the Federal Register for April 1, 1976. Promulgation of the final lighting standards took place on October 1, 1976 which means that the underground coal mining industry must comply with face illumination requirements by April 1, 1978. As mentioned previously, the first proposed ru1emaking for illumination of underground coal mines was published in the Federal Register on October 27, 1971. In early 1972, Consolidation Coal Company (Consol) and the United States Bureau of Mines agreed to a cooperative study of underground face illumination; Conso1 felt that expertise in this field would become increasingly important. Conso1's initial efforts in illumination were aimed at investigati.ng practical lighting systems for underground face equipment. We were concerned with installing unobtrusive lights which provided sufficient face illumination for safety, but at the same time were readily maintainable, electrically reliable, and physically sheltered from damage.

Jan 1, 1977

By Neil S. Fishman

Tabular uranium ore in the Grants uranium region, New Mexico, occurs as tabular layers of a urano-organic mixture suspended within host sandstones of the Morrison Formation. The intimate urano-organic association points to the organic material as the main ore control. Petrographic evidence indicates that the organic material was postdepositionally introduced into the host sandstone, probably as humic acids; however, the mechanism by which these acids precipitated from solution remains uncertain. A model, the cation scavenging model, is proposed in this paper to explain humic acid precipitation. The model, supported by evidence from regional alteration studies of the host sandstones, proposes that cations responsible for humic acid precipitation were scavenged from framework grains which altered during passage of the humic-rich fluids through the host sandstone. This process, coupled with the affinity of organic molecules for each other, caused flocculation of humic acids into tabular zones. The precipitated humic substances then continued to concentrate uranium to form the orebodies. The cation scavenging model requires only one solution, the humic-bearing solution, in the precipitation process. All cations necessary for humic acid precipitation originated in the host sandstones. This model contrasts with a previously proposed model--the brine interface or two solution hypothesis--in which it was proposed that a cation-rich brine introduced into the host sandstones provided the cations necessary for humic acid precipitation. The brine hypothesis has several drawbacks, one of which is unrealistic hydrologic reconstructions necessary to accommodate mineralization at various stratigraphic horizons in the Morrison Formation. Moreover, no mineralogic evidence exists to suggest a brine occupied the host sandstones at the time of mineralization. The proposed cation scavenging model for humic acid precipitation not only readily accounts for humic acid precipitation, but also is consistent with geologic observations and regional alteration studies.

Jan 1, 2013

By Russell L. Cook

Stringent environmental regulations, which have limited the use of sludge ponds, coupled with the economic incentive to clean more 'coal or to add fine coal cleaning additions to existing preparation plants have increased the use of static thickeners in preparation plants. The Lamella Gravity Settler, sometimes de signated Lamella Thickener, is a shallow depth sedimentation device which has been applied in a variety of industrial process and wastewater control projects in place of the conventional raked thickeners. This paper presents the theory and design of the La-mella Thickener, as well as describing the operating results from several full scale installations in a variety of Appalachian preparation plants.

Jan 1, 1977

By E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 100,000 tons of ore per day and has copper ore reserves estimated to be in excess of one billion tons. Functional groups within the Geology Depart¬ment (currently staffed with six professional and two support personnel) include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pit metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct explora¬tion and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater' resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1983

By Miroslav Cervenka

The Coal, characterized by coal quality parameters as for example, ash content (Ad), moisture (Wrt), heat content (Qr1), sulphur content (Sd) and other parameters is still in many countries the basic source of energy. Energy is life, especially in modern society, where the demand for ecologically clean energy is very high; and therefore, there is great importance in effective coal utilization Direct utilization - burning of coal for energy generation, is still one of the most effective methods. In most cases, it is one of the cheapest energy transformation methods in spite of the fact that this energy transformation is connected with the deterioration of our surroundings. Deterioration can be substantially reduced if the burning of coal at power stations, heat power stations and other coal consumers is optimized. That means the burning is done in steam boilers, the technical state of which is very good; the coal has minimimum .variations with respect to the projected values; and the burning process is controlled and checked not only from a regulation point-of-view but also from an ecological point-of-view. The instrumentation capable of measuring the characteristic coal quality parameters in real time exists and it forms the basic assumption for the work our research team has made. The proper application of this instrumentation is able to provide information for burning process optimalization. It is the main topic of this paper, which is the compilation of the information on our work -made during the last five years. The whole information is based on practical experience and applied systems in Czechoslovakia in the mines and power engineering industry. See [Cervenka, 1989]

Jan 1, 1992

By Manoj Khandelwal, Bright Akuinor Tsidi, Newton Amegbey, Daniel Mireku-Gyimah

This study emphasizes the importance of understanding the factors that influence the throwing of flyrock in mining operations, a significant hazard to both workers and nearby structures. Moreover, it highlights how blasting engineers, when estimating flyrock occurrences and their travel distance, typically rely on input parameters such as powder factor (PF), hole length (HL), subdrill (SD), spacing (S), hole diameter (D), burden (B) and stemming length (ST), while overlooking crucial factors like velocity of detonation (VOD) and charge per bank cubic meter (CPBCM). Through analysis using support vector machine (SVM) modeling in MATLAB, the study underscores the impact of including or excluding VOD and CPBCM on flyrock throw distance.

Jul 1, 2024

By P. Bevilacqua, G. Vallebuona

Empirical models are now used for predicting the performance of hydrocyclones in terms of capacity. cut size (d50.c), water split and partition curve. These models (such as the model by Lynch and Rao and the model he Plitt) were developed and checked for hydrocylones with diameters larger than 4 in. However, for smaller-diameter hydrocyclones, little empirical modeling has been done. This paper reports on an extended experimental research program on small hydrocyclones. For these cyclones, the suitability of existing empirical models was investigated and their accuracy was compared. To improve the predictive capability of these models to small cyclones modifications to the equations are proposed.

Jan 1, 1996

By Christoph Wels, Michael Royle, Shannon Shaw

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2000

By Bruce Congleton

One year ago this month, we in Central Florida witnessed the beginning of a most exciting and glamorous attraction. After three years of construction and anticipation, Walt Disney World opened its gates near Orlando and during its first year of operation received a flood of over 10 million visitors---half of all who came to Florida last year! The side effects of this newest addition to Florida have been phenomenal. Traffic on heavy days has been backed up for 30 miles from the amusement park along a major interstate highway. Hotels and motels have been jammed packed for months, and reservations are still difficult to make. Gasoline stations, restaurants and souvenir shops are doing a booming business. Everywhere you look as you ride the highways of Central Florida you see the signs of growth. New hotels spring up almost overnight. Golf courses galore. New housing projects and apartments sprawl where orange groves used to be. New roads criss-cross areas which were once deserted. There seems to be no end to the steady influx of tourists and new residents to the Sunshine State. And it's mainly because that we are the Sunshine State that they come. Air and water pollution is and has been at a minimum in Florida. Pollution and emissions are fighting words among some groups dedicated to preserving the bountiful environment we share in Florida. Little wonder then that some of these people display concern when they learn that just 50 miles from the entrance to the Magic Kingdom of Disney, phosphate draglines strip away thousands of acres of land each year to extract one of our nation's most precious

Jan 1, 1972

By L. Alan Weakly

The Powder River Basin of northeastern Wyoming and southcentral Montana contains the largest strip minable reserve of compliance coal (0.27 kg or 0.6 or less Ibs of sulfur per million Btu) in the United States. In mining parlance, it is the mother lode. Wyoming's portion of the Basin is called the Southern Powder River Basin (SPRB). It has been the nation's top coal producer for the past nine years. And based on 1997 production statistics and estimated strippable compliance coal reserves, Wyoming should remain the nation's top producer for the next 51 plus years. In August 1994, ME featured 10 articles that covered all aspects of coal production in the SPRB. In this issue, five authors update the 1994 articles and provide a pre- diction of what the Basin will look like at the turn of the century. In addition to this article, the titles and authors of the other five articles include: ? "Geology of Wyoming's Powder River Basin coal field," by Gary B. Glass and Robert M. Lyman. ? "Coal quality challenges in the Powder River Basin," by Sharon Roness, Richard A. Turpin and Robert A. Young. ? "Markets for Southern Powder River Basin coal," by , Patti J. Best and Patrick W. Wright. ? "Evolution of mining equipment in the Powder River Basin," by Kenneth R. Miller and James L. Long. ? "Hauling coal into the 21st century," by Dave Willis and Will Cunningham.

Jan 1, 1998