Search Documents

By Louis A. Panek

Research on roof bolting has developed significant information with respect to the functions that can be performed by properly installed bolts and the methods that can be used to ensure that effective installation has been achieved. The present paper brings together results that are pertinent to the design of a bolting system for reinforcing horizontally stratified mine roof with vertical bolts. The design approach is based on the use of bolts to decrease the maximum bending stress within an arbitrary sequence of roof strata (such as shown by figure 1) in which the only loads are the weights of the individual beds. The use of rock bolts to achieve other objectives, such as to stabilize a fractured rock mass on the periphery of a mine opening (3), is excluded from consideration herein.

Jan 1, 1964

By Palmer C. Sweet

Kyanite. andalusite, and sillimanite are anhydrous aluminum silicate minerals, and they have the same chemical formula, Al2SiO3. Dumortierite and topaz are also classified as aluminum silicates although they contain boron and fluorine respectively. Mullite (a rare mineral named for its discovery site, the Scottish island of Mull) is produced when kyanite, andalusite, or sillimanite are heated. Synthetic mullite, also classified as an aluminum silicate, is formed by melting alumina and silica, bauxite, and kaolin or alumina, kaolin, and kyanite, depending on the type of synthetic mullite desired. These materials are either sintered in rotary, periodic, or tunnel kilns, or fused in an electric arc furnace. The world's largest producer of kyanite is the United States. Domestic kyanite is presently produced from one company at two sites in Virginia; Kyanite Mining Corporation mines kyanite from Willis Mountain and adjacent East Ridge in Buckingham County in the central Piedmont province of Virginia. Internationally, kymite is produced in Australia, Brazil, India, Kenya, Sweden, and Zimbabwe; the former USSR also produces kyanite (Fig. 1). Andalusite is produced by Piedmont Minerals Company, Inc. in the Piedmont province near Hillsborough, NC. Andalusite is also produced in France, India, the Republic of South Africa, and Spain (Fig. 1). Sillimanite is produced in Australia, Brazil, India, Spain, and the Republic of South Africa; the former USSR is also thought to be a major producer (Fig. 1). Some of the countries produce only for domestic use. Synthetic mullite, made by sintering and by electric arc fusion, is produced by Mulcoa (Mullite Company of America) in Andersonville, GA, and by Washington Mills Electro Minerals Corporation in Niagara Falls, NY. Annual world production of kyanite, andalusite, sillimanite, and synthetic mullite is approximately 672 727 tons (Potter, 1988). GEOLOGY Mineralogy Kyanite is a blue to light-green, triclinic mineral that occurs in long, thin-bladed crystals and crystalline aggregates in gneiss, schist, and pegmatites. The mineral has a hardness of 5 parallel to the long axis of the crystal and a hardness of 7 across the crystal. Andalusite is a yellow, brown, green, or red orthorhombic mineral that occurs in thick, almost square prisms in schist, gneiss, and hornfels. Gem quality andalusite exhibits a strong pleochroism; brownish-green in one direction and brownish-red perpendicular to it. Andalusite also occurs in placer concentrations where it has weathered out of rock. Sillimanite is a brown, pale-green, gray, or white orthorhombic mineral that occurs in long, slender, needlelike crystals in schist and gneiss. Chemical and Physical Properties Chemical and physical properties of kyanite, andalusite, and sillimanite are noted in Table 1. Kyanite is the only mineral that irreversibly expands when heated (calcined to produce mullite) and may offset the shrinkage of most ceramic or refractory ingredients when heated.

Jan 1, 1994

By V. B. Achanti, A. W. Khair

Developing a laboratory procedure for the determination of coal-seam compressive strength has been a subject of discussion for many decades, and the reliability of laboratory determinations is often the subject of debate. A coal seam’s characteristics, the method of sample collection, the specimen preparation method and the testing procedure can often result in drastic variations in the test results. In this paper, the development of a laboratory testing procedure for the determination of coal-seam compressive strength is presented. Two samples that were collected from different coal seams were tested in this study. First, the inherent characteristics, i.e., coal structure. Hardgrove grindability index (HGI), Slake durability index, proximate analysis and mechanical properties (Young's modules and Poisson's ratio), of each coal were determined. The results were used to categorize the coal scams in terms of the characteristics liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes, cylindrical and cubical, were tested to determine which shape produced the most reproducible strength values. Third, four loading rates within the static testing range, i.e., 0.007, 0.07, 0.34 and 0.7 MPa/s (1.0, 10, 50 and 100 psi/sec), were used to determine the ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics, were established. Background Laboratory testing of coal specimens for the determination of seam compressive strength has been a subject of discussion since the early 1900s. Many researchers have tested coal specimens to estimate coal-seam compressive strength for use in pillar design to insure the safe operation of [ ] mines (Unrug et al., 1986; and Hirt et al.. 1992). Yet, there is a lack of a universal procedure, and, no matter which approach is used, it becomes the subject of intensive debate. A great deal of work has been performed on the subject, and there is much information available in the literature. Some of this work concerns quantifying the influence of specimen shape and size on compressive strength (Bieniawski. 1968: Barron et al.. 1992: Khair and Xu 1994; and Khair 1994). As indicted in the literature, coal is a heterogeneous material, consisting of discontinuities such as cleats and bedding planes, which are likely to produce variable strength results (Holland, 1964; Unrug et al., 1986). Some of the prominent issues that influence the determination of coal-seam compressive strength in the laboratory are: •the collection of a representative sample from a coal seam; •the geometry, i.e., shape and size of the specimens to be prepared and tested: •the loading rate at which the specimens are to be tested:

Jan 1, 1997

By Gretchen K. Hoffman, George S. Austin

Soil amendments or soil conditioners generally carry the con- notation of being useful for problem soils or soils needing special treatments to produce maximum yields. Many different materials have been utilized, both inorganic and organic. Only the most commonly used and those that appear to have potential to become commonly used will be discussed. Soil productivity depends on many factors. Soil amendments mainly modify physical characteristics and microbial action, and/or change the pH of a soil, rather than directly supplying plant nutrients. They give soil the needed physical properties to allow plant growth, fight erosion, or save water. Some soil amendments provide nutrients in addition to altering the physical, biological, or chemical characteristics of soil. The term "soil amendment," as it is used by Soil Science Society of America, allows soil amendments to be materials other than those used primarily as fertilizers (Anon.,1987). Soil amendments as fertilizers of any type will not be considered here because this aspect is more relevant to the previous chapter entitled "Agricultural Materials: Fertilizers" in this volume. Several inorganic soil amendments have been used since the early 20th century to alter the character of soil: limestone, lime, and similar calcium-rich carbonates and oxides for acid soils, and calcium sulfate (gypsum) and native or uncombined sulfur for alkaline soils. The use of these amendments (limestone, lime, gypsum, and sulfur) or their equivalents has been studied and documented in many basic soils tests (McCaslin and Boyle, 1980). Perlite and vermiculite are considered in separate chapters and only a brief statement of their use as soil conditioners will be made in this chapter. Peat is the principal natural organic soil amendment, but manure, both as a fertilizer and soil conditioner, is used in every part of the world. In less-developed countries, manure is the primary soil fertilizerlconditioner. An organic-rich material designated as "humate" has been marketed as a soil amendment for many years and will be addressed in this paper. Other materials are discussed by the Soil Science Society of America in its Special Publication 7, "Soil Conditioners" (Stewart, 1975). They include bitumen emulsion, polyacrylamide, polyvinyl acetate, polyvinyl alcohol, bentonite, nonionic surfactants, and natural mulches. Zeolites can be added to the list of miscellaneous soil amendments (McCaslin and Boyle, 1980), as can calcium chloride (Pressler and Pelham, 1985), sulfuric acid, ferric and ferrous sulfate, aluminum sulfate, ammonium polysulfide, calcium polysulfide, and ammonium bisulfite (Stromberg and Tisdale, 1979). Sludge will not be considered as a soil amendment because it has properties more consistent with fertilizers. All these "other materials" account for a very small amount of the volume and value of soil amendments used and will be only briefly discussed.

Jan 1, 1994

By D. W. Park

The Longwall Strata-Control and Maintenance System (LoSCo-MS) is a software and data-communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and the forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels, including excessive shield load, low setting pressure, leg leakage, poor shield performance and imminent maintenance problems. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, the next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems in their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 2000

By David M. Parkes

Geology is frequently complicated, hence only more regular deposits are mined. Coal is generally thick, often steeply pitching and usually soft or well-cleated. Due to competition from open-pit mines, only two underground mines are operating, McIntyre and B.C. Coal. Several other mines are being planned, the method being evenly divided between hydraulic, longwall, and room and pillar. McIntyre mines in the flat part of their formation (up to 20 degrees) uses continuous miners and shuttle cars in the 3m and 6m seams. This company is considering a retreating longwall face. B.C. Coal operates a hydraulic mine in a 16m thick seam dipping at 10 to 55 degrees with a productivity of about 20 tonnes per manshift.

Jan 1, 1982

By Stephen R. La Brooy, Tong Deng, Pritam Singh, David M. Muir, A. J. Monhemius, G. W. Warren, E. Peters

The controlled addition of ammonia to cyanide solutions inhibits the leaching of copper minerals but extracts up to 80% Au using as little as 10% of the cyanide compared with conventional cyanidation of copper-gold ores. The solubility of copper minerals and copper speciation in solution is dependent on NH3, CN-, pH and Eh. Rotating disc and electrochemical studies show that gold is leached by a mixed Cu-CN--NH3 complex with either Cu(II) or O2 as oxidant. This complex is slowly oxidised to CuCN and Cu(OH)2 by air.

Jan 1, 1993

By D. J. Wood

BHP Copper has grown, in just over six years, from a minor participant to the world's largest privately owned copper producer. BHP Copper's major asset is the world's largest copper mine -Escondida in Northern Chile. Ten years ago investing in Chile was considered high risk. Today, Escondida represents an investment of approximately US$2 billion. Reward is the result of managed risk and Escondida is a clear demonstration of both. The Ok Tedi copper and gold mine in Papua New Guinea represents a Rubicon of risk and a retrospective on reward in a developing country on the doorstep of a developed one. The story of these two mines encapsulates risk in the mining industry.

Jan 1, 1998

By Sarkis G. Ampian

This late 1979 Bureau of Mines report presents current stocks and monthly consumption rates for Guyanese refractory bauxite (GRB), with emphasis on the impact of the GRB shortage on the refractory and downstream industries, general background material, and an evaluation of the situation resulting from the strike of Guyanese bauxite workers during the summer of 1979. A study by the Bureau indicated that industry stocks contained little more than a month's supply of GRB--30,000 calcined short tons (CST), at present consumption rates of 25,000 CST per month. The report was requested by the Federal Emergency Management Agency (FW) in response to refractory industry requests that the Government release GRB from the National Stockpile to minimize forecasted industry problems. The report traces the historical innovations in the high-alumina and/or bauxite-type refractory products industry, eventually leading up to fabrication of modern, high-quality firebrick and monolithic refractories.

Jan 1, 1980

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

By Terry A. Ring

Sand bed filters are used to remove large and small particles from liquid streams. The large particles are removed by the straining action of the filter bed and the small particles are removed by particle deposition on the surface of the bed particles. Particle deposition, while being essential for the filtering action of colloidal particles, is not the only process that occurs in the filter bed. Other processes that occur are (1) the substrate becomes filled with particles limiting further deposition, and (2) some deposited particles are resuspended. The sum total of all these processes determine the performance of a filter bed.

Jan 1, 1982

By John E. Frost

Duval's (now Battle Mountain Gold Co.) copper and gold deposits in the Battle Mountain District in Nevada are in two subdistricts - Copper Basin and Copper Canyon - about 18 km (11miles) apart. Location of the two subdistricts is shown in Fig. 1. The two centers of mineralization have distinctive geologic and ore characteristics that required different innovative approaches to exploration and development. Nearly all of the copper from Copper Basin has been recovered by heap leaching. Because of relatively high gold and silver values in the Copper Canyon ores, a significant part of the sulfide copper ores has been recovered by a conventional flotation mill at Copper Canyon. Recently, this mill has been converted to the recovery of gold that is mined from zones peripheral to the copper deposits. Prior to Duval's entry, small amounts of copper, gold, silver, lead, zinc, and antimony had been mined in the district over a nearly 100 year period, beginning in 1866. The bulk of the $13 million total production to 1962 was derived from copper and gold lode ores and gold placers. Duval's interest in Battle Mountain-arose directly from a submittal by Asarco, which controlled key claims in both the Copper Basin and Copper Canyon subdistricts. Asarco acquired its holdings in the district in 1959 and undertook limited exploration until mid-1961. At that time, the company decided to dispose of its interests. Duval was invited to evaluate Asarco's properties and accepted. On Dec. 6 and 7, 1961, J.E. Frost, R.C. James, R.W. Sayers, and H.A. Schmitt, representing Duval, and K. Richard and E.W. New- man, representing Asarco, visited Copper Basin and Copper Canyon. Frost concluded that the properties were of considerable interest and prepared, by Jan. 12, 1962, a voluminous report recommending that Duval acquire and explore Asarco's properties. Furthermore, he recommended a large initial exploration program that included not only geologic mapping, geochemistry, and geophysics, but also the extensive drilling that was to involve, as the first phase of exploration, 49 drill holes in Copper Basin and 21 drill holes in Copper Canyon. Following property agreements between Duval and Asarco, and Duval and several other claim owners, geologic mapping, geochemical surveys, and drilling began in August 1962. Exploration drilling was completed in July 1964 and engineering studies in April 1965. Development of the Battle Mountain properties was authorized in July 1965, and production commenced in the first quarter of 1967. Because of the unusually high oxide copper content of the ore bodies, particularly in Copper Basin, a much larger than typical proportion of the copper in the deposits has been recovered by heap leaching. The generalized geology and ore zones of the Copper Basin are as shown in Fig. 2 and of Copper Canyon in Fig. 3.

Jan 1, 1991

By K. Thomson

The Mule Canyon gold deposit, located 14 miles ESE of Battle Mountain, Nevada, was discovered in 1986 as the result of a GFMC grass-roots exploration program. Drilling to date has identified six discrete orebodies which contain a demonstrated gold reserve of 8.487 million tons at an average grade of 0.136 oz/ton, totaling 1,152,000 ounces. Mineralization is associated with argillic alteration and silicification, localized along NNW trending high-angle faults within Miocene basaltic andesites. Trace element geochemistry at Mule Canyon is typical of upper level hot spring precious metal systems, displaying elevated Ag, As, Sb, Hg, and Se.

Jan 1, 1993

By E. Finch

Beneficiation tests were conducted on samples from three ore zones in the Los Monos, Navay orebody in Táchira State, Venezuela as part of an overall feasibility study. The scope of work included ore sample characterization, flowsheet development, and optimization of beneficiation variables on a bench scale followed by confirmation on a pilot plant scale. Phosphate in the ore samples occurred primarily as francolite and was associated with quartz, kaolinite, and feldspar. Liberation of the phosphate began at 589 microns (28 mesh) for the main ore zone sample and at 295 microns (48 mesh) for the lower-grade ore zone samples. Development tests on simulated mining composites demonstrated that the samples responded well to 589 micron (28 mesh) grinding, two stages of high intensity scrubbing, conditioning at high % solids with caustic and equal amounts of tall oil and fuel oil, and separate coarse and fine flotation circuits with one stage of roughing and two stages of cleaning (reflotation). Concentrates in the range of 31.5-34% P205 with recoveries from 64-70% were obtained from the mining composites. Product quality for all concentrates in the range of 31.5 % P205 was good; 1.40 CaO/P205 and 0.04-0.05 minor element ratios. Confirmation testing in a continuous pilot plant produced results similar to those achieved in the laboratory.

Jan 1, 1993

By A. Pinches, R. Winby, P. J. van Staden, M. K. Rhodes, P. C. Miller

This paper is a progress report on the commercialization of using bioleaching for base-metal concentrates. The paper focuses on bioleach processes for recovering copper from chalcopyrite and nickel/cobalt from pentlandite/pyrrhotite. Data is discussed from pilot-plant trials in which an overall recovery >95% was obtained for the bioleaching of copper from chalcopyrite. The pilot plant was operated in closed circuit with solvent extraction and electrowinning circuits for final metal recovery. For the bioleaching of nickel and cobalt from pentlandite/pyrrhotite, an overall recovery of 97% was achieved. Precipitation routines were used to produce a final nickel/cobalt product. The pilot plants were capable of treating a few kilograms of concentrate per day. Prominent features in the design of a 1-t/day (1.1-stpd) copper-bioleach demonstration plant for the treatment of chalcopyrite concentrate are discussed. The plant, which is now under design, will be constructed and operated based on the results obtained from the laboratory pilot-plant campaigns. Issues of scale-up for the demonstration plant, together with integration into upstream and downstream processing, are also addressed. Independently derived capital and operating costs are presented for a possible commercial plant. These cost studies indicate the principle economic issues in considering the application of bioleaching to the extraction of base metals. The benefits of bioleaching complex concentrates that are not amenable to physical beneficiation and economic treatment by conventional smelting are highlighted. Issues, such as the environmental aspects, that illustrate the benefits of bioleach technology are given.

Jan 1, 2000

By J. C. Motz

The advantages of producing a fine mill feed have been recognized for many years. The extent to which fine crushing can be carried out will vary and depends on the ore characteristics, plant and crusher design. Unfortunately, the ore characteristics are generally beyond our control, so the concentration of effort lies primarily on the plant arrangement, equipment design and operation Where fine crushing should stop and grinding begin is controversial and is influenced greatly by personal opinions and experiences. Often, this break point will be different if consideration is being given to a new plant in comparison to a modest expansion. Most new plant designs employ the largest and most efficient equipment. The modification of existing plants becomes more complex because of the space requirements and the related equipment already in operation. Fine crushing is, of course, a relative term. Obtaining a final crusher product of minus 3/4" is commonplace today and can occasionally be obtained in an open circuit final crushing stage.

Jan 1, 1980

By Lee Ann Arrington-Webb

Thiele Kaolin Co. has invested much time and money in achieving and maintaining its IS0 9002 certification. Through a regimen of process control and documentation, routine audits and a commitment to quality management, this kaolin producer is a competitive pigment supplier in a worldwide market. Background In 1987, the International Organization for Standards developed the ISO 9000 quality management system. This series of standards is used as a means to ensure customers that a quality management system is in place. Certification of a company does not mean that an individual product is of high quality. Rather, it demonstrates a supplier's ability to meet its customers' product and service needs. It also shows that a company has documented records to assure product consistency. The ISO 9000 system was begun in England during the early 1980s. During the mid-1970s, the British manufacturing industry was experiencing low quality. In an attempt to boost quality standards, the British government established the BS 5750 standards system. In 1987, BS 5750 was incorporated into ISO 9000. The ISO 9000 series consists of three levels of certification. ISO 9001 is the model for quality assurance in "design/development, production, installation and servicing." This standard applies to companies that rely on research and development to bring products that frequently change to market. ISO 9002 involves "production and installation" only. This standard is relevant to industries that produce a specific product according to specifications - either their own or their customer's. ISO 9003 is the model in "final inspection and test." This standard is the least detailed of the 9000 series. It is also the most applicable to companies that purchase, inspect or sort and resell. The quality system requirements for certification are outlined in the 18 elements of ISO 9002. These include: 4.1 - Management responsibility. 4.2 - Quality systems. 4.3 - Contract review. 4.4 - Design control. 4.5 - Document and data control. 4.6 - Purchasing. 4.7 - Control of customer-supplied product. 4.8 - Product identification and traceability. 4.9 - Process control. 4.10 - Inspection and testing. 4.11- Control of inspection, measuring and test equipment. 4.12 - Inspection and test status. 4.13 - Control of nonconforming product. 4.14 - Corrective and preventive action. 4.15 - Handling, storage, packaging, preservation and delivery. 4.16 - Control of quality records. 4.17 - Internal quality audits. 4.18 -Training. Continuous improvement, though implied in maintaining these requirements, could potentially be included in the quality system requirements in the next revision. The ISO 9000 requirements and documentation system is shown in the hierarchy pyramid (Fig. 1). A company's quality policy serves as the top of the pyra-

Jan 1, 1997

By Nicholas Chlumecky

A practical method is described for determining or checking whether underground supports such as props, posts and mechanized longwall supports have bearing areas of proper size in relation to the type of ground or floor strata on which they are standing, It is felt that this information provides an approach to eliminate, as much as possible, a potential grave source of error during the selection of roof supports. This would also affect the choice of costly mechanized longwall equipment where it is possible that the size of the bearing area is not as carefully determined as, for instance, the design strength of structural components.

Jan 1, 1967

By AJIT SWAIN, SUNATI MOHANTY

The abstract discusses the importance of predicting the dewatering performance of industrial hydrocyclones from laboratory models. It highlights the challenge of scaling up design and operating parameters for efficiency estimation. The paper describes experiments with a 2-inch and 4-inch hydrocyclone using silica sand. It details the development of a model using the Nageswararao hydrocyclone model and a simulator to estimate model parameters. The model is validated with experimental data, and a new model is developed using 4-inch hydrocyclone data. The technique is then extended to predict dimensions for a full-scale dewatering cyclone operating at higher throughput and solid concentration.

Mar 30, 2022

By Kousik Sinha

The advantage of using a clean coal as a feedstock in a direct liquefaction plant is improved performance of the plant by several factors e.g., increased throughput of coal; reduced wear and tear of valves, pipes, and pumps; increased liquid yields, etc. This paper examines the technical feasibility for cleaning Illinois #6 coal as a feedstock to a direct coal liquefaction plant via selective agglomeration using a coal-derived heavy distillate, Wilsonville V-1074 as agglomerant. Effects of addition of Kerosene or coal-derived Naphtha as conditioner, coal particle size, slurry pH, oil to coal ratio, and operating temperature on ash reduction and clean coal weight recovery have been studied. Results show that about 70% of the ash can be removed from this coal and the clean coal weight recovery over 85% can be achieved by using this technique with suitable selection of coal particle size, slurry pH, mixing intensity and oil to coal ratio.

Jan 1, 1991