Search Documents

By R. K. Mehta, M. G. Bersch

Characterization of an ore or mill product is routinely performed by time consuming and tedious chemical analyses, sink-float separations, etc. Additionally, these types of tests do not provide data concerning the interrelations and interlocking of the mineral constituents. This paper discusses some of the applications and capabilities of the Minerals and Material Science Research Center at The University of Alabama. Back-scattered electron images of coal, oil shale, complex suldfide, and tantalium ores were acquired using a JEOL 8600 electron microprobe with a NORAN (formerly Tracor Northern] 8500 image analysis system. Methods of analysis and typical results are discussed.

Jan 1, 1992

By L. G. Austin

Using an instrumented laboratory high-pressure grinding rolls mill, the grinding force, gap dimension, mass flow rate and net mill power were measured for six coals and a crystalline quartz. A technique was developed to estimate the compressive stress-strain curves for compression of the materials in the mill plus the effects of elastic decompression. To reconcile the mill power and grinding pressure results, it was necessary to allow for the energy recovery on decompression. No clear correlation was obtained between the form of the stress-strain curves or the variation of specific mill power factor with the Hardgrove grindability index (HGI), although coals with the lowest and highest HGIs (i.e., 44 and 106) gave results significantly different from the other coals. Feeds below 140 mesh (105 µm) flowed more rapidly than coarser feeds and would not build up high grinding pressures. This indicated shearing and fluidlike properties rather than compression as a locked bed.

Jan 1, 1998

By T. B. Szwilski

ISO 14000 series are voluntary international standards that address environmental management system standards, environmental auditing, environmental labeling, environmental performance evaluation, and life-cycle assessment. An environmental management system (EMS) is a facet of an organization's structure that addresses the immediate and long-term impact of a company's products, services, and processes on the environment. Many companies in the United States are taking a cautious wait-and-see approach before embracing ISO 14000. A few mining companies are reviewing the standards and using them as guidelines. The paper outlines the status, possible benefits to the mining industry, and options available to a company wanting to become involved in the ISO 14000 standards.

Jan 1, 1997

By R. L. Wiegel

There are approximately 40 million tons per year of phosphate rock produced in the United States, half of it by flotation. The bulk of this is used to produce diammonium phosphate, an essential ingredient in the commercial fertilizer mixes used by the thriving U.S. agricultural community. This paper describes the mineral beneficiation practices of the phosphate industry, with special emphasis on flotation. There is also an attempt to include those items that might be considered emerging technologies for the industry as it faces the problems of a diminishing high-grade reserve and the necessity for implementing dolomite/francolite separations.

Jan 1, 1999

By Michael Michaylov, Elana Vlasseva

This paper presents a method for three-phase foam preparation recipe optimization. The pressurized foam is injected into porous media of gob area for prevention and fighting of SPONCOM fires. The method includes laboratory experiments for main foam properties as well as mathematical optimization procedure. Optimization criteria are formulated reflecting foam application purposes. The influence of solid phase on foam heat stability is shown. Results from optimization procedure for four foam agents by varying fly ash consistency of foam are presented. Theoretical basis for original construction of foam generator, specially constructed for of three-phase foam generation, is set u

Jan 1, 1997

By Dwayne C. Kicker, Duk-Won Park

As the use of longwall mining increases in the U.S.. there is a need to better understand the stress redistribu- tions indicative of this method. To control high stress concentrations, the yield pillar concept has been developed. A physical longwall mine model has been designed to study the effect of yield pillars in deep mining. The model in- cludes sensitive stress measuring devices, a new excavating technique, and a new model material. This study includes the use of both regular and yield pillar systems and has successfully simulated the mode of stress change in chain pillars.

Jan 1, 1986

By Christopher Laughton, Michael P. Bruen

At Fermilab, a 4000-ft long underground complex has recently been constructed for a high-energy physics experiment. The complex is sited up to 350 ft, below grade principally in bedrock. The rock excavations were mined by TBM and drill and blast methods and supported by a combination of rock bolts, dowels and shotcrete. Water control was achieved using a combination of pre- and post-excavation grouting, drainage systems, drip shielding and air desiccation measures.

Jan 1, 2003

By James R. Runkle

Studies in eastern Ohio, northern West Virginia, and southwestern Pennsylvania determined whether subsidence caused by longwall mining influences soil moisture and tree growth. Soil moisture was measured both over new longwall panels and over an unmined control area throughout the growing seasons of 1990, a wet year when the panels were excavated, and 1991, a dry year. No significant effects of mining could be detected. Tree growth was studied in two pairs of woodlots. In each pair, one woodlot was located over a longwall panel excavated about 1980 and the other over an unmined area. Differences in tree growth between mined and unmined areas were neither significant (for most species) nor consistent in direction. The above results imply that if mining does have impacts they are likely to be highly site-specific and localized such as by disruptions of springs or soil slippage.

Jan 1, 1986

By K. Adam

Uncontrolled disposal of pyrite wastes and concentrates comprise a major source of acid drainage in active and abandoned sulphide mines. In this paper, the state?of-the-art mitigation measures implemented for the final reclamation and closure of a pyrite concentrate stockpile at Platia Karra, Stratoni mines, Greece, are presented.

Jan 1, 2002

By Nai-piu Tong, Huaren Dou, Sui-shun Poon, Leslie H. Swann

This paper mainly presents geotechnical aspects of a vehicular underpass that was built across under one of the busiest highway in Hong Kong. The underpass, in a section comprising an upper arch and invert slab, is approximately 6.2 m high at crown and 15 m wide at the base level with 40 m in length. The construction inevitably requires the underpass to be built using tunneling techniques to keep the overheadroad traffic uninterrupted. The paper will describe the design of temporary support for the tunnel excavation that was provided by an arch formed with horizontal pipes, which were installed using the pipe ramming method. The pipes arch was then supported by steel ribs founded on rock or mass concrete. Permanent lining design consideration was also discussed. Results of numerical modeling of the soil-structure interaction using the 2-D computer code FLAC will be presented. The predictions have been compared to the monitored results during construction, which indicates the prediction is in reasonable agreement with the measurement in the light of ground movement. The construction challenges will also be discussed in the paper.

Jan 1, 2003

By Regina N. Tempel, Laurie S. Balistrieri, Lisa L. Stillings, Maggy F. Lengke

The Dexter pit lake, within the Tuscarora volcanic field in Elko County, Nevada, formed after closure of the Dexter mine. Mineralogy at the Dexter mine is related to widespread feldspar, silica, and chlorite alteration. Major mineralogy includes quartz, alkali feldspar, albite, phlogopite-biotite, hornblende, iron-titanium oxide, chlorite, kaolinite, smectite, illite, and sericite, with lesser amounts of calcite, zircon, apatite, and rutile. Trace element geochemistry is characterized by high levels of As, Ba. Cr, Cu, V, Zn, B, Zr, Li, and U. Detailed mineralogy and geochemistry are required for geochemical models to accurately predict trace element concentrations in pit lake waters.

Jan 1, 2000

By M. R. Paterson

Operational and economic factors tend to favor the application of continuous processes in preference to batch processes in the majority of mineral processing applications. In this paper, the requirement for a Continuous Elution Process is established and the development of a large-scale pilot plant is described. It is based on a Continuous Elution apparatus which has a number of special features. These are the subject of various patent applications. The apparatus is suitable for adaptation to the AARL, Zadra and other methods of elution. The performance of the Atmospheric Continuous Elution System (ACE) is concluded to have significant advantages over the batch process.

Jan 1, 1986

By M. A. Berdine, C. N. Thompson, D. Brock

The raise bore method of shaft construction has been success-fully used in the mining and construction industries for over thirty years. In the mid 1990’s, Twentymile Coal Company (“TCC”), now affiliated with RAG American Coal Company, used this method for a moderately deep small diameter shaft and the raise bore and slash method for a shallow larger diameter shaft. In late 2001, TCC contracted to raise bore a 431-meter deep, 6.2-meter diameter shaft. During the raise bore and shaft lining processes, regional horizontal stress fields resulted in extensive elliptical caving beyond the original design diameter. This paper discusses the engineering approaches and procedures used to safely complete construction of the raise bore shaft.

Jan 1, 2004

By Michael M. Maier

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

Underground mining has the potential to be one of the more dangerous industries in the United States and the world. Following recent disasters in Sago, WV; Darby, KY, and Crandall Canyon, UT, the mining industry was reminded of the need for a system to allow trapped miners awaiting rescue to survive following a disaster. To address this need, Battelle has developed a Mine Barrier Survival System (MBSS) that surpasses all current technologies and sets a new standard for keeping miners alive in the event of a fire, flood, explosion or collapse. The MBSS creates a temporary refuge for miners who cannot escape by using inflatable barriers and a post-fire atmosphere scrubbing system to define the ?safe haven? and remove CO2 and CO while replacing oxygen and providing heat. Current personal-protective systems in use are designed to provide breathing air for only a few hours when, realistically, it may take days for rescue teams to reach trapped miners. Battelle?s MBSS is designed to aid up to 15 miners for four days.

Jan 1, 2008

By William A. Vogely, Lawrence J. MacDonnell

This section begins with an introduction to several key environmental laws. This is followed by a discussion of some of the issues raised by such environmental regulation. Finally the subject of regulatory reform is addressed. Overview of Selected Major Environmental Laws The number, type and complexity of environmental laws and regulations affecting mineral resources development have grown at an astonishing rate since the 1960s. The most significant laws and regulations are those addressing the use of the public lands; those concerned with air quality, water quality, and surface reclamation; and those defining government responsibility for its actions having important environmental consequences. The laws and regulations governing activities on the public lands will be taken up in the section 5.15C, "Minerals and Land Management." In this section we will concentrate on five primary laws: the Clean Air Act, the Clean Water Act, the Surface Mining Control and Reclamation Act, the Endangered Species Act, and the National Environmental Policy Act. The Clean Air Act: The legislative and regulatory framework for controlling air pollution has developed in a series of steps. Most important for present purposes are the Clean Air Act of 1970 (P.L. 9 1-604) and the 1977 Amendments (P.L. 95-95). The rather complex air quality control scheme includes four key elements-national ambient air quality standards, state implementation plans, the prevention of significant deterioration program, and the non- attainment program. National Air Quality Standards. The 1970 Clean Air Act is a landmark law because it contains the first explicit recognition that pollution is a nationwide problem requiring a national control program. The federal government through the Environmental Protection Agency (EPA) was to establish national air quality standards for at least the six pollutants named in the Act (sulfur dioxide, carbon monoxide, total suspended particulates, photochemical oxidants, hydrocarbons, and nitrogen dioxide). These standards were to be established so as to protect public health, "allowing an adequate margin of safety." The cost of achieving these standards is not to be considered. The 1970 Act unrealistically required that these standards be achieved in all areas of the country by 1975. As the program has developed, the air quality control regions are now to be designated as "attainment" or "nonattainment" with respect to each of the national standards. State Implementation Plans. Under the Act the states are given the primary role in achieving the ambient standards. States are to develop and implement control plans governing emissions from all existing and new sources. These plans can include emission limitations for existing stationary sources, transportation control plans to reduce emissions from mobile sources, and pre- construction review of new stationary sources to assure compliance with new source performance standards. The EPA must approve all state implementation plans. Sanctions are given to the EPA to be applied if states fail to submit acceptable

Jan 1, 1985

By Mehmet Guney

[The Atlantis-II-Deep is a hydrothermal mineralization located along the median valley of the Red Sea at a water depth of about 2200 m. Extensive exploration of the metal-rich brine deep revealed a potentially mineable deposit on economic interest consisting of oxides, silicates and sulphides with considerable concentrations of zinc, copper, cadmium and silver. Geostatistics was applied to assess the most likely in-situ vague of the metal potential for economical exploitation. Semi-variograms were constructed to characterize the structure of the regionalized distribution of the geological parameters. Volume grades and thicknesses were determined by the kriging technique, avoiding systematically biased high or low grades, and then block .tonnages were computed. The estimation variances, distribution of errors and histograms of observed and kriged values in each grid Mock were also produced.]

Jan 1, 1983

By J. Engesser

A research project was undertaken to determine if coal addition tofluxed-magnetite pre-fired pellets would reduce nitrogen oxide (NOx)emissions during pellet induration. Iron oxidation rate tests, coal oxidation rate tests and calcination rate tests were conducted in a laboratory furnace to determine the amount of coal necessary to provide adequate heat for limestone calcination without producing detrimental effects to magnetite oxidation. Pilot scale pot-grate tests were then performed with and without coal in the pre-fired pellets to verify pellet quality parameters and nitrogen oxide emissions. The off-gas during each pot-grate test was analyzed for NOx, CO2, CO, SOx, and O2. There was approximately a ten percent reduction in NOx emissions with coal addition during the normal pot-grate firing cycle. There was a 75% reduction in NOx emissions during firing cycles that used 25% to 75% excess air during firing rather than the normal 300% excess air.

Jan 1, 2003

The National Mining Hall of Fame and Museum (NMHFM) in Leadville, CO will induct the class of 2011 on Sept. 10, 2011. Representing the coal, metallurgical/processing, research and development, marble and lead industries, this year?s inductees cover a diverse crosssection of the mining industry. William Francis Diamond, Wayne Hazen, Redfield Proctor and Jeffrey Zelms will join 210 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 24th Annual Induction Banquet and Ceremony. The members of this year?s class were selected for being visionaries, leaders and ambassadors both within their own sectors and across the industry at large. Diamond had an illustrious engineering and managerial career that spanned four decades with Island Creek Coal Co. During that time, he was responsible for the engineering and construction of the deepest coal mines producing in North America at the time.

Jan 1, 2011

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION This manuscript is based on site inspections of five existing mines and the detailed analysis of two of the five. The detailed analysis and mathematical models of the two mines are presented herein in order to demonstrate a method of predicting mine water inflow using existing mines as a data base. Water management procedures were studied at all mines. Our original criteria for mine selection were that the mines be less than five years old and have an inflow rate in excess of 2000 gpm (7.6 m3/min). Background hydrologic and hydrogeologic data were required so that two of the mines could be used for our computer modeling experiments. Our original criteria proved to be difficult to meet. We contacted numerous mines via various sources. Many mines were unable to meet the cri¬teria stated or were not interested in cooperating with us. Therefore, we allowed some flexibility in the application of these criteria to satisfy our orig¬inal requirements. Although the visitations at all the mines are not discussed herein the characteristics of the two mines simulated are presented. These simulated mines consist of a uranium mine in New Mexico and a lead mine in Missouri. The mines and owners will remain anonymous by request. URANIUM MINE-CASE HISTORY NUMBER 1 Mine Location The uranium mine that we simulated is located in northwestern New Mexico. The ground surface at the uranium mine is at an elevation of approx¬imately 7000 ft (2134 m) above mean sea level. The climate is arid to semi-arid with an average annual precipitation of approximately 10 in. (25.4 cm) (John and West, 1963). Geologic Setting It is essential that a conceptual model of the stratigraphy, hydrostratigraphy, and structural geology of a mine site be developed prior to simulation by a mathematical model. If such a conceptual model is not developed prior to simulation major errors are difficult to avoid. The uranium mine we have simulated is located in the San Juan Basin (Fig. 68), which is a structural basin located in northwestern New Mexico and adjacent parts of Colorado, Arizona, and Utah. The sedimentary rocks present in the deepest part of the basin are nearly 15,000 ft (4572 m) thick (John and West, 1963). The regional dip of the sedimen¬tary rocks in the Grants area is generally northward toward the San Juan Basin; the regional attitude is modified locally by normal faults and folds (Hilbert, 1963). The rocks of interest in this area are sedimentary in origin and range in age from Penn¬sylvanian to Cretaceous. They rest on the Precam¬brian core of the Zuni Uplift. Associated intrusive and extrusive rocks are of Tertiary and Quaternary ages (Hilbert, 1963). The deepest sedimentary unit of interest at this mine site is the Morrison Formation as described by Hilbert (1963). The Morrison Formation con¬sists of three members in the general area of the mine site; the deepest member is the Recapture. The Recapture Member consists of alternating beds of gray sandstone and grayish red siltstone or mud¬stone with strata up to several feet in thickness. Only a few small deposits of uranium are contained within the Recapture Member. The Westwater Canyon Member overlies the Recapture Member of the Morrison Formation. The Westwater Can¬yon Member is approximately 150 ft (46 m) thick and consists of light brown to gray, poorly sorted, arkosic sandstone, and some interbedded gray mud¬stone. The Poison Canyon Formation denoted in subsequent discussions, tables, and figures was de¬termined to be a part of the Westwater Canyon Member. The separate connotation is used for the description of mining operations and hydraulic properties but a separate physical description is not included. This member of the Morrison Formation contains many large deposits of uranium. This is (some pages in this article are damaged)

Jan 1, 1986