Search Documents

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways; therefore, air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between [ ] the intake and the return airway is zero. At this point, there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation. However, in practice, the position of the neutral point is not static and it changes as the ventilation system parameters change. Booster fans have the potential to increase the capacity and efficiency of coal mine ventilation systems. However, these fans add a significant pressure source to ventilation systems and can create areas where the pressure in the intake is less than the pressure in the return causing recirculation. In systems with multiple booster fans, there may be multiple recirculation paths and, as the capacity of these fans increases, recirculation is more likely to occur.

Jan 1, 2012

By Francois E. Heuze

Excavation of large rock caverns is a stepwise process. Whether one uses a heading and bench method or a multiple drift system, the use of excavation steps enables one to introduce the reinforcement, such as bolts or shotcrete, at the earliest possible stage. Knowing the spatial distribution and properties of rock materials and geological discontinuities, the cavern geometry and its reinforcement must be optimized. The finite element method of analysis is a powerful tool for such optimization. However, the models are only as good as their ability to account realistically for the physical attributes of the prototype and for the excavation sequence. They must include the following: - ability to model an incremental construction process. Thus requires the use of "Restart" procedures where displacements and stresses from a previous equilibrium are saved for the next step. - ability to model non-linear rock material behavior; in particular, the post-peak behavior of the rock which retains a residual strength when con-fined. The stability of many under-ground structures rests with the "broken" rock carrying significant loads. - ability to account for the non-linear behavior of geological discontinuities. These are two-fold. First, up to peak, non smooth rock joints will dilate. In a confined situation, dilation will increase joint strength by a consider-able amount (Obert, et al, Brady, 1971, Heuze,1978a), Then, beyond the peak, the joint also retains residual strength.

Jan 1, 1978

By Ottmar Burghardt

Sintering of iron ore has undergone a dramatic development world-wide. Today, the annual world production amounts to approximately 600 million tons. At present, the sintering process in competition with pelletizing, seems to offer certain advantages inasmuch as it allows the use of solid fuels. Also, its charging behaviour in the blast furnace is, in general, considered as being better than that of pellets. This is true, in particular, for the charging behaviour and the gas permeability in relation to the grain size. Moreover, instead of charging limestone into the blast furnace, for instance, the basic components which are necessary for the burden materials can generally be supplied in a simpler and more cost-effective way by using basic sinter instead of basic pellets. While in sintering, with basicity rising to the range of 1.6 to 1.8 CaO : SiO2, the capacity increases and the sinter quality shows improvements in most of its characteristics, the pro¬duction of basic pellets generally requires a higher fuel rate, when compared to acid pellets, while production capacity decreases and some of the quality characteristics deteriorate.

Jan 1, 1982

By A. S. Ibrado

The adsorption of silver on activated carbon from cyanide solutions was studied as a function of concentration, ionic strength and pH. In cyanide solutions, silver exists mainly as the linear Ag(CN)2 complex and adsorbs on activated carbon following the Freundlich isotherm. The uptake and rate of adsorption increase with the addition of KC1 and KNO3 but changes only slightly with pH. In contrast, the adsorption of Cu(I), Zn(II), Cd(II), and Hg(II) shows marked changes with pH, closely following the predominance profiles of their neutral and singly-charged cyano complexes. Clearly, multicharged negative complexes are repelled by the negatively-charged carbon surface. This sensitivity of activated carbon to the charge of the adsorbing species indicates that silver adsorbs as an anion, not chemically bound to the co-adsorbing counterions. For the same reason, activated carbon is selective to metals that form neutral and Singly-charged cyano complexes, namely gold and silver.

Jan 1, 1988

Fine coal is substantially more costly to process than coarse coal because of technical difficulties associated with separating fine particles and removing process water from both clean coal and refuse. Therefore, companies are often forced to discard coal fines to waste impoundments. According to a recent report published by National Research Council, the U.S. coal industry is discarding 70-90 million tons of coal fines annually to 713 active impoundments, most of which are located in Central Appalachia. On October 11, 2000, a 72-acre impoundment near Inez, Kentucky, accidentally released 250 million gallons of coal slurry into nearby underground mines, creeks, rivers, and schoolyards, thereby creating serious environ-mental concerns. Fortunately, recent advances in separation technologies make it possible to recover fine coal more efficiently from existing coal preparation plants and from waste streams previously discarded to impoundments. The availability of these new technologies allows companies to increase profitability and minimize environmental risks, which are conducive for achieving sustainable mining.

Jan 1, 2003

By V. Roze, R. N. Parkinson, R. Shepherd

The alphaDOSIMETER is a complete, integrated system designed to monitor the immediate worksite of underground miners where the disintegration for radon daughters is a risk to the health of mining personnel. The dosimeter weighing little more than one pound is worn by each miner throughout the entire shift and is powered by the miner's cap lamp battery. After this integration period, the unit is connected to a reading network whereupon the day's data is dumped, calculated and stored. Beginning in July 1980, prototype units were subjected to vigorous underground testing in uranium mines in Canada and the United States and in tin mines in Cornwall, U.K. The testing results are summarized and proposals advanced for a typical mine monitoring system utilizing the alphaDOSIMETER.

Jan 1, 1981

By F. G. Loper

Simulation as a mathematical technique is not new. However, recent increases in digital computer speeds and the ease of programming with languages such as Fortran have centered a good deal of attention around simulation in the last few years, Many sophistications of the method have been developed during this time. However, the ability to simulate mathematically still hinges on the ability to ignore unimportant details which would complicate the mathematics and make simulation impractical, Thus, with this attitude in mind, it becomes very easy to design a pseudo- simulator which will predict average conditions very well, but can not truly allow a detailed study of the system being simulated. Most simulations fall into this category, along with the case mentioned here. This paper is not intended to be a critical treatise of the simulator used to study a particular mining system. Instead, it will be used to illustrate the aspects of simulator development. The steps in the development of any simulator are described, along with same detail of the phosphate mine simulator itself.

Jan 1, 1966

By T. J. Durbin

At some surface and underground mines, control of ground-water inflow involves significant costs. These costs include the capital costs for installing a dewatering system, power and other costs to operate and maintain the system, and costs to treat and dispose of the water that is collected. To minimize these costs, design of a dewatering system utilizing wells has been formulated in terms of a nonlinear operations research problem using quadratic programming. Using this formulation, the locations, depths, pumping rates, and pumping schedules of wells are selected so as to minimize the total costs of the dewatering system.

Jan 1, 1993

By H. Suharyono

A laboratory investigation of flocculation following polymer addition during slurry flow through pipes and in-line (static) mixers is described. Results are presented showing the effects of flow velocity, pipe length, in-line mixer elements and the use of multiple addition points on flocculation performance as measured by settling rate and supernatant turbidity. The effects of agitation and mixing time are shown to be generally consistent with the results of equivalent tests, both batch and continuous, conducted in stirred tanks.

Jan 1, 1995

By Howard G. Coopersmith

A resource of low grade good quality diamonds has been discovered through the Diamond Company NL-Moonstone Diamond Corp. Joint Venture. A limited bulk sample diamond test of two large kimberlite pipes on the Kelsey Lake Property, Colorado, has been completed. These kimberlite pipes have petrological and mineralogical indications of the presence of diamond. Small diamonds were recovered from surface samples. Drilling and trenching revealed both pipes were complexes of diatreme facies kimberlite. One pipe contains crater facies kimberlite as well. This is the first reported occurrence of crater facies kimberlite in the Province. Approximately 1000 tonnes of kimberlite rock was excavated and processed through a scrubber -HMS -Sortex -Grease Plant. Significant diamonds were recovered. The diamonds were generally of good color and clarity, with many being in the gem and near gem categories. Grades are considered low however. Additionally, a small potential resource of alluvial diamonds is present.

Jan 1, 1991

Despite two large projects represented in the keynote docket, the mood of the 2011 SME Arizona Conference was summed up best by Ferol Baker, general manager of New Mexico Copper Corp. (a wholly owned subsidiary of Themac Resources Group), ?In the past, it seemed like you couldn?t go to a conference like this without hearing about one big new greenfield project after another. Now what you see is companies doing internal expansion or small-scale brownfield development.? Overall, the tone of this year?s meeting, held at the J.W. Marriott Resort at Starr Pass in Tucson, AZ, was upbeat, yet practical. From the keynote and luncheon addresses to the six panels of sessions, the projects described were positive about the future, yet focused on the details required to make those projects come to fruition.

Jan 1, 2012

By Ralph T. Buscarello

For practical purposes, the terms "natural frequency," "resonance" and "critical speed" are synonymous. A part passing though its "critical" or "critical speed" may also be said to be "resonant" or "resonating." The vibrations of a precisely balanced part can be magnified by the structure in which it is assembled. Anyone who has driven an automobile knows that it will vibrate more at a certain speed than at others. According to the formula for centrifugal force, vibration should increase steadily with a rise in rpm. What happens instead is that the vibration not only in- creases with r m. but suddenly rises at a much higher rate through the critical speed, and then apparently smooths out as the rpm passes beyond it. To visualize what happens, consider a simple flat spring with a weight mounted at one end. When the spring is deflected by pulling down on the weight and then letting it go, the spring will oscillate, and the spring-and-weight system will vibrate at its natural frequency. If the timing or direction bf the impulses imparted to the spring did not coincide with its natural frequency, the result would be an irregular vibration that would not build up. If, on the other hand, the timing and direction of the impulses did coincide with the spring's natural frequency, the result would be a larger and larger amplitude. If the impulses were continued indefinitely, the amplitude of the spring's vibrations would go on rising [while its frequency stayed the same] until the spring broke or the amplitude of the vibrations reached an equilibrium [because frictional or other forces would tend to damp it]. Resonance magnifies the amplitude of vibrations in a relatively undamped system between 100 to 200 times over that of nonresonant vibrations. Frictional or viscous damping often reduces the magnification [from 10 to 20 times], but even with this reduction the amplitude would still be large enough to cause excessive wear, and sometimes even fractures. For example, a blower might show only 0.001 in. of vibration on the manufacturer's test stand. Installed, the blower could pass into its critical speed [the speed at which the frequency of the vibrations caused by the rotor coincides with the supporting structure's natural frequency], and the 0.001 in. of vibration could be resonated to 0.010 in., or as much as 0.020 in. The cure for such a condition would not be to lower the vibration of the blower by further balancing or better alignment but to separate the two frequencies by at least 20 to 30%.

Jan 1, 1970

By Michael Gobla

"Since 1994 the Bureau of Reclamation (BOR) has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has, to a limited extent, applied risk analysis to inactive and abandoned mines to evaluate tailings dams, pit lakes and flooded underground mines. Case histories of potential failure mode analysis, as applied to mine impounded water, illustrate what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first.IntroductionImpounded water and high water content wastes at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (4.1 million m3 or 5.4 million cu yd) release, the Mt. Poly Tailings Dam failure in British Columbia in 2014 (4.4 million m3 or 5.8 million cu yd) release, and the Samarco Fundao Tailings Dam failure in Brazil in 2015 (59 millon m3 or 78 million cu yd) release have renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originate not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes and flooded underground mine workings.Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the U.S. Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984, the agency developed and began using risk analysis methods. BOR operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of 100 years. Many of these facilities were designed and constructed prior to the development and adaptation of modern soil mechanics in dam engineering. Diligent observational monitoring, detailed site investigations and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high-risk sites, significant improvements to dam safety have been achieved."

Dec 1, 2016

By G. A. Weisenfluh

The successful application of factors limiting the? availability of coal in eastern Kentucky depends on ac-curate assessment of the original resources. Examination of several previous coal-resource estimates for the region reveals significant differences among the outcomes. These differences relate to methods of analysis, biases in data and their utilization, and the problem of defining the lateral continuity of mineable beds. Improvements in the methods of estimating the original resources would greatly enhance the reliability of the results of the Coal Availability Program.

Jan 1, 1995

By Michael Bourassa, Sonja Felderhof, Normand Champigny, Steve Vaughan

Introduction -Comparison of International Reporting Standards (Sonja) -Legal and Due Diligence Requirements for Reporting (Steve) -Flexibility to Recognize International Reporting Standards (Michael) -Obligation of SRO’s to Discipline (Michael) -Impact of Sarbanes Oxley on Reporting (Normand)

Jan 1, 2003

By D. M. Larsen

Since start-up in 1985 the Cannon Mine has produced and shipped a 170 g Au/tonne (5 oz Au/ton) flotation concentrate to various smelters for gold and silver recovery. Several processed have been investigated to economically produce dore' at the mine site from the refractory concentrate. This paper describes recent laboratory and pilot scale test work utilized in the process design and engineering feasibility study of a 73 tonne/day (80 ton/day) pressure oxidation and CIL facility. The designed pressure oxidation circuit utilizes a series of vertical autoclave units operating at 170°C (338"F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1993

By R. K. Singhal

A variety of mining equipment is used in the mining of oil sands by surface mining. This includes bucket wheel excavators, draglines, hydraulic shovels and off-highway trucks. This paper examines the existing mining schemes and equipment used Peculiarities of oil sands surface mining and their influence on equipment selection, utilization and mining schemes are described. Recent developments undertaken to improve mine productivity are also dealt with together with some notes on proposed measures to obtain further gains in productivity.

Jan 1, 1985

By G. A. Hufford

The cutoff grade applied to a disseminated orebody mined by open pit affects both the waste ratio, hence the cost of producing ore, and the ore grade, hence the quantity of metal recovered. As such it has a significant impact not only on the annual profit or loss, but also on the life of a mining property. Cutoff Grade Strategies Some commonly used objectives in calculating cutoff grades are as follows: Minimize Unit Cost of Product (1) This is found by adding all costs associated with each possible cutoff such as mining, processing, and marketing. This is divided by the quantity of marketable product obtained at each cutoff grade, then finding the minimum. Because the market value of the product does not enter the calculation it has no effect on this strategy: the same cutoff is selected in good times and bad.

Jan 1, 1986

By Qiong Wu, Li Guo, Qinghua Gu

BP neural network is a multilayer feedforward network trained by error back-propagation algorithm, which is one of the most widely used neural network models. However, BP neural network has exposed more and more shortcomings and deficiencies with the expansion of the application scope. In the prediction of ore quantity, BP neural network has the characteristics of slow convergence and easy to fall into local minimum point. In order to obtain the global optimal solution, and to improve the defects of BP neural network, this paper proposes combination optimization algorithm of genetic algorithm (GA) and BP neural network to improve the speed and accuracy of forecasting the main design flow chart and the analysis of the sort distinguish algorithm are offered, and then some problem in the design and debugging of the algorithm are discussed. On this basis, the GA-BP neural network model is constructed and applied to optimize the initial weights and threshold value of BP neural network. This model choices the floating point coding method to encode the connection weights and thresholds, and divides subjects into several populations. Through the introduction of selection, mutation, crossover, initial weight and other operators, making operational synergies between the various groups. This study selects 30 geological units, 8 quantitative variables (Pb, Zn, Cu, Mo, Si, Ni, Co, V) and 12 qualitative variables to carry out empirical analysis. Then the simulation of the algorithm is carried out in MATLAB and the parameters are analysed. By normalizing the input samples, 22 groups of observation data are used as the training data for prediction, and the latter 8 groups of observation data are used as the test data to be verified. The results show that when the ore quantity characteristics are not very significant, the model will produce prediction bias. But the improvement of the algorithm increases the efficiency of the function approach capacity of BP neural network and conquer the BP neural network system’s instability. It provides an auxiliary guide for ore prediction, which have higher reference value.

Jan 1, 2017

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985