Search Documents

By D. Koren, D. Carson

Disposal of smelter slag may be subjected to regulatory leach tests to deter- mine whether they produce a leachate containing contaminants in excess of stated limits. Contaminants that are most often of concern for smelter slags are As, Cd, Cr, Cu, Ni, Pb, and Zn. The present regulatory tests are based on the assumption of storage in a municipal landfill dump, where wastes are in contact with organic acids. Since slags are not normally stored in such an environment, these tests do not adequately assess the true leachability potential of the slags. Ten slags from six major Canadian nonferrous sulfide smelters were studied. Leaching was done following regulatory and modified tests, including leaching in columns with synthetic acid rain for a 25-week period. The slags were characterized by mineralogical analysis before and after leaching with synthetic rain. The synthetic mineral equivalents (hereafter referred simply as phases) in the slow cooled slags consist of fayalite grains and dendrites, amorphous glass, some spinel and small quantities of complex sulfidic prills and metallics. The phases in the quenched slags consist of amorphous glass, some spinel and small quantities of complex sulfidic prills and metallics. Some metal dissolution took place during leaching. However, for all leaching tests, the concentrations were always below the regulated limits. In general, the content of the potentially leachable elements remains unchanged in the fayalite, in the amorphous glass and in the spinel, whereas the quantity of sulfidic prill and metallics decreases after leaching. Therefore, most of the deleterious element dissolution comes from the sulfidic prills and metallic phases. Metal dissolution increases by crushing the slag, probably due to an increased exposure of the sulfidic prills to the leaching solutions.

Jan 1, 1998

By J. C. Cawley

Improvements in today's maintenance practices are mandatory as more complex and productive machines evolve in the mining industry. By keeping machine reliability high, through improved maintenance procedures, overall mining costs can be reduced. The Bureau of Mines is investigating diagnostic maintenance systems for underground mining machinery. A hydraulic expert diagnostic system and an electric motor predictive diagnostic system have been designed and installed on a Joy 16CM continuous miner. An electrical diagnostic system has been designed and installed on a Joy 14CM continuous miner. Each system is functionally described and the relative merits of expert diagnostic systems versus algorithmic diagnostic systems are discussed.

Jan 1, 1991

By David J. Akers

In past years, water drainage control in coal mines has been primarily directed on the basis of water quantity rather than quality. Due to the recent intense interest in total ecology and environment, emphasis has shifted to the point where the water exiting from a mining operation may be of better quality than when it enters. In most operations this has meant the use of treatment methods (neutralization) while the technology for the prevention of acid drainage is being developed or refined. To date, underground abatement of acid formation has generally been less expensive but also less effective than surface treatment of the mine water. It seems probable that total mine water pollution control will have to include both underground abatement and surface treatment methods. The general acid producing reaction involving the oxidation of pyrite - 2FeS2 (pyrite) + 702 + 2H20 ? 2Fe2S04 + 2H2SO4 - is well known, even though the individual steps are not clearly understood. The major implication of this reaction, that acid production can be eliminated by not allowing the contact of pyrite with free oxygen or water, has been well substantiated both in the laboratory (1,2) and in practice. (3) Underground abatement or control processes can be generally classified into two types: (1) the effective control or elimination of acid causing reactions within the mine, and/or (2) the reduction or prevention of water flow into and out of the mine. Recognizing the fact that these two types may be directly inter-related, this paper will, for the purposes of clarity and simplification, discuss each separately.

Jan 1, 1973

By Gregg A. Swayre, Roger N. Clark, Stephen J. Sutley, Kathleen S. Smith

Imaging spectroscopy is a relatively new remote sensing tool that provides a rapid method to screen entire mining districts for potential sources of surface acid drainage. An imaging spectrometer known as the Airborne Visible/InfraRed Imaging Spectrometer (AVIRIS) measures light reflected from the surface in 224 spectral channels from 0.4 - 2.5 µm. Spectral data from this instrument were used to evaluate mine waste at the California Gulch Superfluid Site near Leadville, Colorado. Here, the process of pyrite oxidation at the surface produces acidic water that is gradually neutralized as it drains away from mine waste, depositing a central jarosite zone surrounded by a jarosite + goethite zone, in turn surrounded by a goethite zone with a discontinuous hematite rim zone. Leaching tests show that pH is most acidic in the jarosite and jarosite + goethite zones and is near-neutral in the goethite zone. Measurements indicate that metals leach from minerals and amorphous materials in the jarosite + goethite and jarosite zones at concentrations 10 - 50 times higher than from goethite zone minerals. Goethite zones that fully encircle mine waste may indicate some attenuation of leachate metals and thus reduced metal loading to streams. The potential for impact by acidic drainage is highest where streams intersect the jarosite and jarosite + goethite zones. In these areas, metal-rich acidic dace runoff may flow directly into streams. The U.S. Environmental Protection Agency estimates (U.S. EPA, 1998) that mineral maps made from AVIRIS data at Leadville have accelerated remediation efforts by two years and saved over $2 million in cleanup costs.

Jan 1, 2000

By E. Rigopoulos

Mining disturbs the environment, even when the ores or the minerals extracted are non-toxic. Silver & Baryte Ores Mining Co S.A (S&B) is committed to minimizing the environmental impacts of its mining activities, by implementing an integrated rehabilitation program wherever it operates. The paper discusses the principles for mining-disturbed land restoration activities on Milos Island for a successful outcome.

Jan 1, 2003

By Ernst Langer

INTRODUCTION Morro do Niquel is located near the small town of Pratdáolis in the southwest part of the State of Minas Gerais, Brazil, about 300 km in a straight line north of São Paulo and 300 krn west of Belo Horizonte. The deposit is known since 1935. Systematic exploration started, however, only in 1957 and production with one furnace in 1962. Since 1969, after the installation of a second furnace, the mine produces about 2 500 tons of nickel, contained in ferronickel, per year. This production is now consumed totally by the Brazilian steel industry. The "Morro do Niquel" is a serpentinite stock of 900 by 400 m which rises 200 m high above the surrounding metamorphic rocks of Algokian age (see Figure 1). On top of the hill there is a leached barren zone of about 200 by 400 m, generally 20-30 m deep, which consists practically only of a boxwork of quartz colored brown by limonite. Surrounding this zone on the sides of the hill is weathered, decomposed serpentinite which contains about 213 of the economic nickel mineralization. Roughly 113 of the ore reserves lie below the leached overburden representing ore of a different type. The geological map and cross-section, Figure 2, give a clear picture of the occurrence.

Jan 1, 1979

By John E. Pavlick

The availability of concentrated brines rich iodide, bromide, chloride, sodium, magnesium and calcium ions has led to extensive chemical manufacturing operations in Michigan. The brines, ranging 1,000 to 8,000 feet below the earth's surface, are the remnants of ancient oceans which periodically covered and receded over the land area which is now Michigan. After pumping the brine to the surface, iodine and bromine are extracted via an oxidative process. Iodine and bromine find application in catalysts, disinfectants, flame retardants, oil field fluids, film, and gasoline additives. Addition of alkalinity to the brine precipitates magnesium hydroxide, used in high quality refractories needed for steel manufacture. The brines are also the country's primary source of calcium chloride, employed in ice and dust control.

Jan 1, 1984

By Jerry Luttman, Mark Dubay, Anvesha Dogra, Elizabeth Dwyre, Wei Hu

The I-75 Modernization Project (Segment 3) just north of Detroit, MI is being delivered as a Design-Build-Finance-Maintain (DBFM), which is a Public Private Partnership (P3). The project includes design and reconstruction of 5.5 miles of freeway, including a depressed section with a 20,630-ft long, 14.5-ft inside diameter, up to 100-ft deep stormwater tunnel, multiple drop shafts, and a pump station. The project also includes a maintenance term of 25-years. This is the first time MDOT has used a P3 delivery method for a major highway and tunnel project. This paper describes the development of the P3 documents, including performance-based tunnel and shaft technical requirements, and the approach to project risk management, financing, and insurance coverage.

Jun 23, 2024

By James Warren Andrews, Philip C. Nyberg

The regulation of exposure of underground personnel to radon and its daughter products has significantly changed since the 1950's. The U.S. Bureau of Mines - Mining Enforcement and Safety Administration (MESA) - Mine Safety and Health Administration (MSHA) sequence of standards and regulations have lowered the maximum allowable occupational exposure and now the new Environmental Protection Agency (EPA) National Emission Standards for Hazardous Air Pollutants, effective in 1990, have further regulated uranium mine emissions. Under the authority of Section 112 of the Clean Air Act (42 U.S.C. 7401), the EPA has set regulations for the control of radon (Rn-222) emissions from underground uranium mines as well as other sources. Since the venting of radon from the mine atmosphere to the outside air is a major component of the miner's protection, and since this is the first quantitative effort to limit gaseous mine emissions to the environment, it was felt that it would be useful to examine the implementation of the EPA regulation at working mines. The concern was not only for determining compliance with the regulation but also for observing what effect the rule might have on mine air quality and thus on worker exposure. The regulation is stated in terms of the maximum permitted radiation dose to the closest potentially exposed individual, which is calculated from a computer program supplied by EPA and radon emission rates measured by the mine operator. Relative proximity to nearby populations determines the allowable magnitude of mine exhaust ventilation emissions. For some mines this is a serious operational constraint.

Jan 1, 1991

By A. A. Wallach

During the early design stages of the San Manuel Concentrator, numerous questions were raised concerning the required slope for tailings pipelines. The tailings disposal area which had been selected was so situated, that an average down-slope of 5% existed. A gravity tailings disposal system was to be designed and it was necessary to determine the optimum pipeline slope for design purposes. This information was also necessary to determine the life of the available disposal areas before tailings pumping would be required. At approximately the same time as this problem arose, it was reported that a concentrator in the southwest was having considerable operational difficulties due to periodic plugging of tailings lines. These factors combined made it seem desirable to conduct some sort of test work which might give information concerning the flow characteristics of the tailings to be produced, from the San Manuel Concentrator. It was felt that the maximum information could be obtained if a tailings line could be erected which would allow for varying slopes, varying heads and accurate measurement of pulp velocity. A five-foot Denver Agitator was installed on a bank overlooking a cut for a rail- road track. Approximately 160 feet for new &-inch pipeline with victaulic connections was installed on low trestles along the track, with provisions made for varying the slope of the line by use of accurately constructed sets of shims, A valve discharge was installed on the tank so agitated pulp could be run into a standpipe at controlled volumes. This standpipe was 10 inches in diameter and approximately 5 feet high. A 4-inch nipple welded into the side of the standpipe approximately one inch from the bottom was connected to the 4-inch pipeline. At the discharge end of the 4-inch pipeline a launder arrangement was so constructed that the entire discharge could run into a pump sump or into 50-gallon measuring vessels. In normal operation the flow was from the agitator to the standpipe through the pipeline into the pump sump and from there pumped back to the agitator tank.

Jan 1, 1958

By Ben F. Dickerson

For a number of years in office bull sessions, I have not so jokingly discussed the engineering or management fiasco of the year or decade. Usually, governmental projects are in the vanguard, such as tanks that won't tank, or heavy water plants that don't produce heavy water, etc., etc., all to the flutter of the taxpayers' hundreds of millions, or billions of dollars. The mining industry has also brought forth a share of this type of fiasco. Ordinarily, due to lack of funds, not opportunity, the stockholders only stand losses of a few tens of millions. Little knowledge of these major errors gets to the outside world, for the ordinary stockholder is usually not very alert, and managements are extraordinarily adept at discreet midnight internments in the fine print of the footnotes of annual reports.

Jan 1, 1975

By K. Hanna

This paper describes a method to improve coal mine entry intersection design. The method considers the effect of in situ stresses, local geologic conditions, rock physical properties, and mining sequence. Development of the method is discussed, including the results of field instrumentation studies and numerical modeling investigations. Data required to evaluate the effects of roof span, mining sequence, entry orientation, and bolting patterns on intersection stability are also presented. Ground control studies conducted by the U.S. Bureau of Mines in two underground mines in the Illinois Coal Basin have shown that in situ horizontal stresses and roof geology have a critical effect on intersection stability. Methods to reduce the adverse effects of these parameters are emphasized. Typical failure behavior associated with specific geologic and horizontal stress conditions is' presented to illustrate proposed control methods to alleviate adverse ground conditions.

Jan 1, 1988

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

By S. A. Moffatt, S. K. Kawatra, T. C. Eisele

This paper describes the decomposition of bulk samples to fine particles using alkali metal vapors. Basalt, pyrite, alumina, pyrex and quartz glass samples were exposed to sodium vapors at elevated temperatures for different time periods up to 30 hours. Examination of the particles showed that fragmentation occurred preferentially along grain boundaries. Emphasis of this paper is on the theory of the degradation mechanism and the size distribution of the particles produced.

Jan 1, 1992

By Meghan M. Murphy, Derek Penrice

The Downtown Rail Extension (DTX) is principal element of the planned second phase of the Transbay Joint Powers Authority’s (TJPA) Transbay Program. When complete, this regionally critical project will connect Caltrain’s regional rail system and the California High-Speed Rail Authority’s statewide system to the Salesforce Transit Center in downtown San Francisco via a 1.3-mile tunnel. Studied since the 1970s, the DTX has now received environmental clearance, and key stakeholders are aligned on the project’s configuration and its expedited delivery. This paper describes efforts to optimize the DTX configuration and develop an informed project delivery strategy that incorporates construction industry feedback on project phasing, contract packaging, and procurement methods that accomplish the project’s budget goals.

Jun 13, 2021

By P. K. Kaiser, M. Cai

When designing an efficient and effective support system for burst-prone ground, it necessary to select the most appropriate, i.e., the ‘right’ support components, including areal and reinforcement components. For this paper, it is assumed that the areal support is not the weakest link and the support performance is controlled by the rock reinforcement and holding components (bolts). We discuss the loading modes of rockbolts under static and dynamic loadings and analyze published data from laboratory and field tests. The mechanisms of energy absorption of dynamic rockbolts are presented and rockbolts are categorized based on factors such as energy absorption capacity, energy absorption rate, direct and indirect energy absorption capacities, rock mass bulking or displacement control, and shearing resistance capacity. Guidelines for selecting the ‘right’ rockbolts to build an effective rock support system for burst-prone ground are provided.

Apr 26, 2022

By E. A. Rychkun

With the aid of modern computer automation, certain mathematical techniques are easily adapted to geophysical, geochemical and geological data analysis. First and second derivative filtering (or transformation) of raw data, in many cases, gives a better indication of anomalous conditions than conventional methods of analysis. The calculations involved, which are tedious manually, are simple, accurate and fast with the assistance of Fourier analysis and modern computers.

Jan 1, 1968

By Arthur R. MacPherson

Este capítulo revisa las etapas que deben seguirse desde el momento de considerar la molienda autógena en el desarrollo de un nuevo depósito de mineral o en la expansión de una planta existente, hasta la compra de un molino autógeno. En este caso el término autógeno incluye: semi-autógeno, molinos de pebbles secundarios y molino de bolos (trozos), así como los sistemas de molienda autógena total. También se han incluido las alternativas por vía húmeda y seca. Antes de programar el ensayo debe decidirse cuantas muestras brutas son requeridas para calcular propiamente las posibilidades de molienda autógena del depósito. También ha de tomarse la decisión, de como y donde deben tomarse las muestras, por ejemplo: planta piloto situada en el sitio de localización de la planta o en otro lugar establecido; molienda en húmedo y/o en seco....etc. En el mismo programa del ensayo se obtendrán ciertos datos fundamentales. Los ensayos deberán incluir un trabajo suficiente. para determinar cuál de las moliendas, totalmente autógena o semi-autógena, debe utilizarse; y qué tipo produce la máxima eficacia en la potencia consumida. También, los otros datos pertinentes deben ser recolectados, como por ejemplo: potencias, tonelajes, alimentación, carga, tamaño del producto, carga circulante, etc. Si es necesaria una molienda secundaria para obtener el tamano final, la decisión de qué molienda debe emplearse (molino de pebbles o molino de bolas) puede requerirse un ensayo de trabajo adicional. Finalmente, la concentración del mineral puede jugar un papel importante en la selección del circuito y debería ser una parte del ensayo final una vez que se ha establecido la molienda. Para determinar qué tipo de molinos pueden satisfacer los requerimientos establecidos por la planta piloto, debe tomarse una escala para ciertos datos como: potencia del molino, consumo de acero, simple o doble etapa de molienda, tipo de molino secundario. Para asegurar un posterior entendimiento del depósito de mineral y sus características de molienda, deberán efectuarse algunos trabajos adicionales a pequena escala utilizando pequeñas muestras y molinos para producir unos datos comparables de molienda. También, algunos ensayos tales como medio de molienda óptimo, e índice de trabajo, deberán ser completados.

Jan 1, 1982

By T. J. Joiner

A critical demand exists to develop new mineral resources, and the need for exploration techniques to supplement costly test drilling is becoming; more acute. In the past few years more industries have begun experimenting with geophysical methods to locate and define mineral deposits and delineate reserves. The new techniques have proven profitable in many instances. As a part of a broad long range program to study the mineral resources of Alabama, and in response to requests from land owners and mining companies, the Geological Survey of Alabama is investi¬gating the occurrence of bauxite and kaolin deposits in the Eufeula area. This project is supported by special funds appropriated for this purpose by the Alabama Legislature.

Jan 1, 1966

By Sara J. Heinlein, George Malkos, James E. Lindell, Tony Pestonatto

The 79th Street Water Tunnel Extension Project was initially designed by the City of Chicago, Department of Public Works, to increase the capacity of the City’s south side water distribution system. MWH preformed a design review, prepared the final design and provided construction management for the City of Chicago Department of Water. Construction commenced in September 1995 and was completed in October 1999. The Project connected two existing water tunnels with a new 5.8 km (19,044 ft.) long, 4.9 m (16.08 ft.) finished diameter concrete lined rock tunnel utilizing TBM, drill-blast and mechanical hoe-ramming methods. In addition, approximately 61 meters(200 feet) of concrete lined variable cross section tunnel, a new gate shaft and a temporary construction shaft were constructed. This paper describes the construction of these features and the geological conditions encountered.

Jan 1, 2003