Search Documents

By S. J. Schatzel, K. M. Ajayi, Z. Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Mar 2, 2022

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be re-handled. Prior studies have shown that by only changing blast hole timing with the same blast design, fragmentation and throw alters. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum inter-hole delay for fragmentation has been found by studying timings from 0ms to 45ms. Instantaneous timing between holes increased the throw by over 100 ft, but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw. This paper investigates this optimized inter-hole timing while altering top and bottom column primer time to potentially improve throw while maintaining optimum fragmentation. Timings studied are top initiation, bottom initiation, and top and bottom simultaneously. INTRODUCTION Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading, and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.” Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is re-handled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators has allowed for precise delay timings to be used between rows, holes, and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation. This study consisted of 3 full scale bench blasts at a granite quarry in Talbotton, GA. Each blast was characterized by the timing delay between the top and bottom primer in the blast column of each hole; one simultaneous blast with a 0 ms delay, a bottom-initiated blast with a 1 ms delay, and a top-initiated blast with a 1 ms delay. Fragmentation analysis of the resultant muckpiles was performed using a combination of the PortaMetrics handheld point-and-shoot rugged tablet from Motion Metrics and the software WipFrag from WipWare. Throw was measured by placing strategic distance markers on the floor of the bench and then taking overhead photographs of the muckpiles after each blast. High-speed video footage was captured of each blast using an MREL Blaster’s Ranger II camera."

Jan 1, 2017

By Bee R. Waples

The Alimak Raise Method, using the Alimak Climber, has proven to be a new, fast, economical method of driving raises at the Iron King Branch of Shat-tuck Denn Mining Corporation, Humboldt, Arizona. In order to fully understand the advantages of the Alimak Raise Climber, it is necessary first to describe the basic machine; second, a complete cycle of a raise round; and third, the comparative speed and economy afforded the Iron King operation by using this new method of raise driving: The raise climber consists of a drilling platform that is raised and lowered by two 6.2 HP compressed air motors that drive, through roller chains and sprockets, three worm gears connected in series. These worm gears drive pinions which grip the guide rail rack. The worm gems are fitted with spring-loaded couplings so that a small rock or grit in the rack is passed over without disturbing the mesh between the rack and the other pinions.

Jan 1, 1961

By Terry O. Arney

This paper is a description of the digital Data Acquisition and control System that is installed at Cities Service's Pinto Valley Concentrator. Pinto Valley Concentrator ? The Pinto Valley Concentrator (5, 41 is located approximately seven miles west of the town of Miami, Arizona. The Concentrator is situated south of the open pit mine and was designed to process 40,000 tons of ore per day with an average grade of .45% copper. The comminution process consists of primary, secondary, and tertiary crushing, and single-stage closed-circuit grinding 161. Concentration of the copper sulfides is by means of froth flotation. Concentrates are transferred to the Inspiration Consolidated Copper Company smelter in Miami, Arizona through a slurry pipeline.

Jan 1, 1976

By R. R. Young

Good afternoon gentlemen. It is always a pleasure to talk about a subject dear to our hearts--the high speed transfer of bull; materials. Specifically, today we will be reviewing the engineering approach to an age old problem of ship loading and unloading. You may be puzzled by the title of this paper and we will attempt to explain this for you--particularly the use of the words "New Era", since high speed automated facilities are nothing new to the material handling engineer. The new era in material handling designs refers to an all out concerted effort to provide custom engineering tailored to specific operations and economic requirements of the client. It shuns hardware type of engineering wherein existing machines and devices are dusted off and reapplied. It provides automation when automation can be justified and it exemplifies the application of systems engineering to solve specific problems.

Jan 1, 1967

By J. H. Elledge

Hydraulic Transportation of Phosphate Ore from, a 40,000 Cubic Yard per Day Strip Mine IMC is transporting 1500 yards per hour of phosphate ore in a water slurry a distance of approximately five miles from a strip mine to a flotation beneficiation plant at their Noralyn Operation. in Barrow, Florida. This ore, which consists of approximately 1/4 phosphate, 1/2 silica sand, and 1/4 clay slimes, is being pumped through a 20 inch O. D. pipeline using seven 20 and 18 inch GIW metal pumps direct connected to electric, motors. This paper details some of the problems involved and the specific methods used to accomplish this bulk material handling requirement.

Jan 1, 1966

By R. Tanaskovic

Unfavourable climatic conditions in stopes are of significant economic and social importance due to the following reasons: - Working effect is much lower leading to decreased output and work productivity disregarding implementation of mechanization. - Manpower operating capability decreases much faster under unsatisfactory climatic conditions. Under normal climatic conditions a workman would expend much less effort in line with a shorter effective time for the achievement of identical production effects since the work would be more efficacious. The objective of study of problems and climatic conditions is to make the working environment in mines suitable for normal development of operations. Lowering of mining works to increasing depths and winning of a growing number of small orebodies over a broad area makes the problem of creating suitable climatic circumstances more complex. Mining costs are growing due to bench conditions in line with decreasing metal content in the ore, so frequently the investments required for creating favourable climatic conditions represent, in addition to the selection of mining technology, a very important parameter when making decisions regarding exploitation. As known, the basic factors affecting climatic operating conditions in mines-are: temperature, humidity and speed of air flow, implying that the climatic operating conditions are closely related to mine ventilation. Usually, the concept of unfavourable climatic operating conditions includes increased mine air temperature and humidity and low air flow velocity so that heat exchange between human organism and the working environment is impeded or reduced to minimum. Metal mines in Yugoslavia are characterized by the existence of a large number of active faces - stopes and horizons and lowering of mining operations to increasing depths, so that face ventilation solutions are more and more complex. Since its foundation (1961), our Institute is engaged in investigation of factors influencing climatic circumstances improvement of calculations for air distribution and distribution control in complex ventilation networks and study of problems related to ventilation of large volume and irregular configuration faces, as well as application of gained knowledge in our mines. The paper presents the knowledge and experience gained in the case of Lead and Zinc Mine "Trepca" - Stari Trg.

Jan 1, 1980

By M. F. Martin

Dewatering aids are chemicals which enhance the efficiency of mechanical dewatering equipment such as vacuum disc filters and centrifugal dryers. A new dewatering aid has been developed which significantly lowers the moisture content of the mineral concentrate and causes none of the undesirable side effects normally associated with dewatering aids. Highlights of product development from laboratory screening through field testing will be discussed.

Jan 1, 1985

By G. W. Riley, D. E. Pickett

HINDERED SETTLING CONCENTRATION In the free settling of mineral particles in a liquid, the falling particles are at a distance from each other so that no particle is affected by its neighbor. In hindered settling, the concentration of particles is sufficiently high so that each particle is affected by its proximity to other particles in the suspension. Richards and Locke86 have described the hindered settling phenomenon as the condition “.. where particles of mixed sizes, shapes and densities in a crowded mass, yet free to move along themselves, are sorted in a rising current of water, the velocity of which is much less than the free-falling velocity of the particles but yet fast enough so the particles are in motion." This is the condition normally encountered in mineral con¬centration processes. The well known Newton equation for free settling of coarse (ap proximately +10-mesh, 1/16-in. or -- 2000-µm) spherical particles is:87 where v," is free settling velocity, cm/sec; p' is density of the fluid; p is density of the particle, g/cm3; d is particle diameter, cm; g is acceleration due to gravity, cm/sec2; and Q is coefficient of resistance, dimensionless, ~0.4. For the settling of fine spheres in water (approximately 150 mesh or 100 µm) the equation of Stokes pertains:87 where µ is viscosity of the fluid in poises and the other symbols have the same meaning as those in Eq. 1. For particles whose size lies between about 10 mesh (--2000 µm) and 150 mesh (100 µm), their settling velocity can be determined from experimental data. These data are available in convenient form in the text by Taggart88 based on the original work of Richards. Alternatively, a Reynolds number-coefficient of resistance plot may be used to determine the settling rate of such particles.87 The settling rate of spherical particles under hindered settling conditions can also be calculated from Eqs. I and 2 by replacing p', the density of the fluid, by p" the apparent density of the suspen¬sion. The concentration of particles in the fluid thus imparts an appar¬ent density to the composite fluid or suspension greater than that of the liquid alone, resulting in a buoyant effect on the larger particles. Particle shape affects the settling rate of both coarse and fine particles. The general effect is to reduce their settling velocities and the effect is greater for coarse particles and for those settling under hindered settling conditions than for fine particles or free settling ones. For two particles of differing densities but settling at the same velocity under Newtonian conditions, the ratio of their diameters from Eq. 1, called the free settling ratio is: where L signifies the lighter particle and H, the heavier particle. Under Stokesian conditions the exponent would be 0.5. For hindered settling conditions the fluid density p' is replaced by the apparent density of the suspension, p", to obtain a generalized equation for the hindered settling ratio: assuming both particles settle in approximately the same regime. The free settling ratio as given by Eq. 3 has been called by Taggart88 the "concentration criterion" and is used to predict the effectiveness of any gravity concentration process (see Introduction to this section). Based on Eqs. 3 and 4, if two particles of densities pH and p,, settle at the same velocity, the diameter of the lighter particle will be larger than that of the heavier particle. For example, in the case of galena (pH = 7.5) and quartz (pL = 2.65) settling in water (p =1.0) under free settling, Newtonian conditions 3.9. Thus, a quartz particle nearly four times as large as a galena particle will settle at the same velocity. Any quartz particle just slightly less than four times the diameter of the largest galena particle may be separated from it. Under hindered settling, Newtonian condi¬tions in a suspension where p" = 1.65, dL/dH = 5.85 or any quartz particle just slightly less than about six times the largest galena particle may be separated from it. Reference to Eq. 4 indicates that a superior separation between two minerals of differing densities is favored by: (1) coarse particles settling under Newtonian conditions, (2) a large difference in (pa - PL), and (3) separation under hindered settling conditions where p" is high. Of course, there are practical limits to increasing p" excessively because at very high percent solids suspen¬sion fluidity would be lost and the hindered settling separation process defeated. Examples of hindered settling separators are the Dorrco-Fahren¬wald sizer,89 the Rheolaveur box 90 the Spitzkasten,89 and the Willoughby washer.91 These devices make a mineral separation on the basis of both specific gravity and size and all of them are essentially obsolete except for the Dorrco-Fahrenwald sizer and similar devices which still find application for the removal of coarse particles from a much finer particle assemblage and for preconcentration ahead of shaking tables. However, nearly all gravity concentration processes (jigs, tables, flowing film concentrators, heavy media separators) and many sizing devices (sizing classifiers, clarifiers, thickeners, hydrosepa¬rators) make use of the hindered settling phenomenon during the separation of particles. JIGGING Introduction In jigging, a mixture of ore particles, supported on a perforated plate or screen in a layer or "bed" with a depth many times the thickness of the largest particle, is subjected to an alternating rising and falling (pulsating) flow of fluid with the objective of causing all

Jan 1, 1985

By D. J. McCracken

The lithium review did not arrive in time for publication in the June issue The estimated consumption of lithium minerals as raw materials to the glass, ceramic and metallurgical industries in 1992 was 85.5 kt (94,200 st). That equates to about 12 kt (13,200 st) of lithium carbonate equivalent (LCE). An additional 150 kt to 200 kt (165,000 to 220,000 st), or 7.5 kt to 10 kt (8200 to 1100 st LCE), were used in the production of lithium chemicals. The 1992 consumption represents an overall decrease of 3.5 kt (3800 st), or 500 t (550 st) LCE, from 1991. This was a direct result of a worldwide reduction in glass demand due to the economic recession. There are three major producers of lithium minerals. Gwalia Consolidated Ltd. (formerly Lithium Australia Ltd.) in Western Australia and Tantalum Mining Corp. (Tanco) in Manitoba, Canada, both produce spodumene ore. Bikita Minerals, in Zimbabwe, is the largest producer of petalite. Bikita also has the capacity to produce small volumes of spodumene concentrate. The Cyprus Foote spodumene operation at Kings Mountain, NC, ceased production in 1992. It once produced about 2 kt/a (2200 stpy) of "high iron spodumene" for uses other than in the manufacture of lithium chemicals. The lithium products of the major producers are shown in Table 1. The current resources of 13 Mt (14.3 million st) of LCE in the western world will supply demand for more than 50 years.

Jan 1, 1993

By Broderick E. Davis

Each year, about 45 Mt (50 million st) of flotation tailings are discarded in Florida phosphate operations. These tailings only contain about 4% of the phosphate in the ore. However, more than half of the phosphate in the tailings is concentrated in the +600 µm (+28 mesh) size fraction at grades of up to 20% P205. Many phosphate producers have attempted to solve this problem by floating the +425 µm (+35 mesh) flotation feed separately. However, phosphate recoveries in these circuits are typically only 60%. For seven sampled phosphate operations, the phosphate content of the +600 µm (+28 mesh) fatty acid tailings ranged from 15% to 25% P205. In every case, the +600 µm (+28 mesh) fatty acid tailings was higher in grade than the overall flotation feed. Attempts to efficiently recover this coarse phosphate have apparently been unsuccessful at these seven phosphate operations. Recovery of this coarse phosphate would provide an additional 900 kt to 2.5 Mt (I to 2.7 million st) of phosphate annually and add an additional year to the reserves of these important deposits. A typical central Florida phosphate matrix is composed of three different mixtures of minerals. The +1.18 mm (+ 16 mesh) portion is chiefly phosphate pebbles and is beneficiated by sizing. The -106 µm (-150 mesh) portion contains virtually all of the clay minerals and is discarded in the hydrocyclone overflow. The -l mm +106 µm (-16 +150 mesh) material is a mixture of quartz and phosphate minerals.

Jan 1, 1993

By James W. Martin, Robert R. Faddick

INTRODUCTION Virtually every sector of society in our country feels the impact of tunnels, either through the transportation of water, commodities, or people. The economic implications are staggering. The Committee on Rapid Excavation (1) reported that during the near future, 1968-1975, underground excavation activity will comprise 946 miles of tunnels (subways: 85 miles; underground urban highways: 123 miles; intercity highway tunnels: 210 miles; water supply tunnels: 528 miles) and 5,119 million tons of crude ore; metals: 874 million tons; nonmetals: 899 million tons; and coal: 3,346 million tons. It is estimated that the cumulative demand for underground excavation in the decade 1970-1979 will be 13 billion dollars for construction-oriented demand and 16 billion dollars for mining-oriented demand. The respective figures for the decade 1980-1989 are estimated at 22 billion dollars and 18 billion dollars. Of the many advantages claimed for tunnels (2, 3, 4, 5) the environmental considerations are becoming increasingly important. Transportation tunnels particularly for rapid transit systems, offer reductions in noise pollution and air pollution while improving aesthetics and optimizing land use (fewer problems of right-of-way and disruption of utilities). Considerable interest has been shown recently in sub-surface construction and mining (6, 7, 8). Recognizing the future demands for tunnels has led to considerable study of methods to improve rates of tunnel advance per day, safety, and the overall economics. The search for higher rates of advance has Led away from what has heap termed conventional methods (drilling

Jan 1, 1974

By James S. Redpath

"The ways of the world be many and most of the ways be tried, you follow in the footsteps of others till you come to the great divide". These words, written by Robert Service a long time ago, come to mind when I think of our original attitude upon entering into a contract with the International Nickel Company to sink the deepest shaft in the world outside of the Union of South Africa. This shaft was to be sunk to a depth of 7,137 feet from surface, and while it was recognized by all concerned to be a somewhat unusual undertaking in our part of the world, the fact that quite a few shafts had already been sunk to this depth in South Africa probably gave us the feeling that we were following in the footsteps of others. In retrospect, because this shaft was being sunk under entirely different conditions than those existing in South Africa, we were in fact venturing into an entirely new area of endeavour without properly recognizing this fact. It has occurred to me that others considering a similar type of job could benefit from our experience, especially in an assessment of the risks involved and how they compare to those encountered in an ordinary shaft. For comparison purposes, I would define an ordinary shaft as being sunk to a depth of 5,000 ft or less, and a deep shaft as one being sunk to a depth of between 5,000 ft and 8,000 ft. The sinking of the Creighton No. 9 Shaft has been de-

Jan 1, 1997

By G. E. McClelland

In recent years exploration and development of low-grade sulfide precious metal ore deposits has increased. Low- grade ores are usually processed using conventional heap leach cyanidation methods. The potential for acid mine drainage from spent sulfide ore heap leached residues remains a concern even though the processed residue is stacked on an impervious liner system. It is therefore of critical importance to evaluate methods for long term prevention of acid mine drainage from sulfide heap leachable ores during the precious metal recovery process rather than mitigation during the closure and reclamation phase. This paper discusses two simple AMD prevention options for the recovery process phase. Laboratory evaluations were made using a modified humidity cell kinetic AMD test method on two low-grade sulfide ores without addition of an alkaline component and on the same ores with natural limestone or acid neutralizing oxide ore blended with the feeds before kinetic testing. Laboratory results are discussed in detail and demonstrate that blending an acid neutralizing component with sulfide ore effectively prevents the production of acid from the processed residue.

Jan 1, 1996

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: • The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. • That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. • Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equip¬ment, blasting, or water infusion. • To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. • As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. • When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in. - diam). The techniques in detail are somewhat complex and sub¬ject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1989

By Mark L. Bricker

The Jim Bridger Coal Mine, operated by Bridger Coal Co., is located in Sweetwater County, WY about 56 km (35 miles) northeast of Rock Springs. Bridger Coal is a joint ven¬ture between Nerco Coal Corp, the operator, and Idaho Energy Resources Co. The permit boundary encompasses more than 81 km'- (20,000 acres) on the western side of the Continental Divide. Since the mine began opera¬tions in 1974, it has produced about 82 Mt (90 million st) of coal while moving about 344 hm3 (450 million cu yd) of virgin earth. Annual production averages 4.5 Mt to 6.4 Mt (5 million to 7 million st) of run-of-mine coal. Coal is consumed on-site by the Jim Bridger Power Plant, a 2000-MW generating station. Electricity is transmitted to the Pacific Northwest power grid that includes Oregon, Idaho and northern California. Geology The mine is located on the northeast flank of the Rock Springs uplift. This is a broad, asymmetrical anticlinal feature about 97 km (60 miles) long and 56 km (35 miles) wide with a north-trending axis. This uplift separates the Green River Basin to the west and the Great Divide and Washakie Basins to the east. Precambrian rocks on the apex of the uplift are estimated to be 5200 m (17,000 ft) above the Precambrian rocks in the Green River and Washakie Basins. Normal faults with generally less than 30-m (100-ft) vertical displacement cut through the uplift. The dip of strata on the flanks is generally between 3° and 15°.

Jan 1, 1991

By C. E. Silverblatt

The advent of larger quantities of -1/4 inch coal in the raw feed to the preparation plant and the necessity of recovering this material has made the problem of meeting product moisture specifications more difficult. For a number of years thermal dryers have been used advantageously as a means of reducing fine coal moisture content where the over-all economics would justify such an installation. However, these units are not without their drawbacks because of high capital and operating costs, safety hazards and possible degradation of the product, and thus an alternative method of moisture reduction is highly desirable. After the various mechanical variables associated with filtration have been optimized, an examination of theory shows that surface tension and liquid viscosity are the only two remaining variables which might be altered to reduce moisture content.

Jan 1, 1964

By S. J. Bluhm

INTRODUCTION Lesotho is a mountainous area of southern Africa from which water is to be exported in an extensive tunnel system, to industrial regions inland. The related tunnelling project has involved a num- ber of drives using tunnel boring machines [TBMs] to excavate about 100 km of 5 m diameter water tunnels [von Glehn and Bluhm, 1995). This paper describes the ventilation and cooling of some of the tunnel drives from both the operational and design points-of-view with a particular focus on heat generation. There were many common features in all of the drives but this paper is focused mainly on the Hlotse drive which was 18,4 km long. The drives were ventilated using forced ventilation systems to provide appropriate air flow throughout the tunnels and face zones. In addition, the Hlotse drive required refrigeration equip- ment which provided chilled water to the tunnel. While the sec- ondary ventilation systems play an important role in gas and dust handling, the paper concentrates on the primary ventilation and cooling issues. The ventilation of these tunnels was an exacting exercise be- cause: • Rock temperatures and geothermal heat flow were high. • TBMs with relatively high power ratings were used. • Diesel locomotives were used. • Drives were relatively long. • High altitude meant a low air density. An important feature was the simulation and monitoring of the ventilation and heat flow components and the project was characterised by analysis, monitoring and ongoing tactical decision-making throughout the progress. The thermodynamics of the systems were complex because there were many interactive effects and analyses were carried out using special computer pro- grams. The monitoring confirmed the accuracy of the models, and in this manner it was possible to confidently ensure healthy and safe working conditions and still minimise costs. Local ambient climate conditions range from temperatures higher than 35 "C in summer to below -10 OC in winter. Based on available statistical data and the thermal storage/damping effects in the system, design summer ambient conditions were taken as 15 OC/25 "C wet-bulb/dry-bulb. The barometric pressure was 80 kPa and due to the altitude, the ambient air density was only 0,9 kg/m3. The local Authority specified a maximum in-tunnel wet- bulb temperature [at any point] of 32,O OC and a mean wet-bulb temperature [from all locations] of 27,5 OC maximum. The maxi- mum height of ground cover above the tunnel was 1 200 m and the maximum virgin rock temperature was 41 OC; see Figure 1. Diesel dilution criteria specified by the local Authority was a minimum of 0.1 m3/s per rated kW of diesel engine. Other requirements related to gases such as CO, CO2, NOx and CH4 [and the need for intrinsically safe equipment] but these are not of direct relevance to this paper. The actual average face advance was about 30 m/d with good days achieving 60 m/d and good months achieving 1 000 m [23 working days]. The original design tunnelling rate was 50 m/d. DESCRIPTION OF HLOTSE DRIVE VENTILATION AND COOLING SYSTEM The ventilation requirements in the tunnels were dictated by heat and diesel dilution needs. The best ventilation and cooling policy is generally a balance between using increased quantities of fresh air or refrigeration [or both]. In this particular scenario it turned out that, since the diesel emission criteria required large quantities of air, the refrigeration needs were modest. The drive was ventilated using a ducted, forced ventilation system from fans located at the portal. The maximum ventilation requirement was 51 m3/s when the drive was at 18.4 km. From a heat flow point of view, the worst scenario was a heat load of 3.5 MW when the drive was at 7 km. This was cooled by the ventilation air and a supply of chilled water to the tunnel. Refrigeration and chilled water system In the design phase, a detailed comparison was carried out between two general alternatives for providing refrigeration. First, was a system in which refrigeration sets and air coolers are installed on the TBM train; the refrigeration sets are cooled by condenser water piped to and from cooling towers at the portal. Second, was a system in which refrigeration water chillers are in- stalled at the portal and chilled water is piped into the tunnel. The detailed comparison indicated that the capital and running costs of the second system were at least 60 % lower than the in-tunnel plant. There were also many obvious practical benefits for favouring the portal system. The refrigeration plant supplied 23 11s of cold water at a temperature of 10 OC. After providing the cooling effect in the drive, the water returned to the portal where it was initially cooled in open-circuit evaporative pre-cooling towers, chilled in the refrigeration plant and then returned to the tunnel. The cold water flowed into the tunnel in an insulated supply pipe and returned in an uninsulated pipe; the water was simply circulated to the end of the pipe and returned. The cooling effect in the tunnel was achieved entirely through heat transfer from the pipe [long linear heat exchanger] and no air coils or other heat exchangers were required. The cooling requirements were satisfied by the heat transfer to the returns chilled water steel pipe [200 mm]. The pipes were eventually installed to a maximum distance of 10,8 km in what was considered a very practical and cost effective solution.

Jan 1, 1997

By Edmond F. Lawrence

The Calico area lies within the Walker Lane fault zone, six miles north of Schurz, Nevada. The mineralized area is overlain by a thick section of Tertiary tuffs and ash-flows, that have been intruded by a series of andesite plug, dikes, and sills. The pre-Tertiary rocks outcrops only in two areas at one to two miles distance from the drilling areas. Underlying the volcanics are sediments ranging from siltstones, sandstone, calcareous shales, to carbonates of the Luning sequence. These have been intruded by one or more phaneritic intrusives ranging in composition from quartz diorite to quartz monzonite, with the development of a skarn zone on the south flank that contains extensive mineralization consisting of magnetite, pyrrhotite, pyrite, and chalcopytite, with traces of sphalerite, galena, and molybdenite. The magnetite, pyrrhotite, and part of the pyrite appears to be contemporaneous with the skarn, while, part of the chalcopyrite, galena, sphalerite, molybdenite, quartz, and calcite, occurs as minute veinlets cutting the other minerals. This later mineralization may be associated with a late stage of the same sequence, or possibly associated with another intrusive to the southwest. Geophysical work has consisted of aerial magnetics, ground magnetics, gravity, seismic, and induced polarization surveys. Preliminary induced polarization surveys indicated anomalies at depth, both over the magnetic anomaly and to the northwest. Subsequent IP work confirmed this earlier anomaly, and drilling disclosed extensive mineralization at depths of 400 feet on the northwest end and over 1,000 feet to the southeast.

Jan 1, 1967

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016