Search Documents

By Yongsik Jeong, Kwangmin Kim

Conventional tailings slurry contains a significant amount of water, and water management is key to ensuring the stability of a tailings storage facility (TSF). Simply reducing the water content in the slurry before discharging it from the mill could be an effective way to improve TSF water management. This study investigated the potential for using an environmentally friendly polymer as a new drag reduction agent (DRA) to reduce frictional pressure loss and also conserve water. It entailed conducting pipe loop tests to assess the polymer’s effect on pressure loss in tailings flow and then applying the test results to validate a numerical model using computational fluid dynamics (CFD). The model was also used to determine the polymer’s optimal concentrations at given solid concentrations and flow rates, its effect on energy efficiency for tailings transportation, and its potential for saving water. A case study for a mid-sized, hard-rock mine with a throughput of 50,000 t/day found that the solid concentration could be increased from 30 to 45% with no pressure loss by applying 1996 m3 of the polymer per day. Adding the polymer also resulted in water savings of 57,552 m3/day. The results of this study demonstrated the potential for using the new DRA not only to improve TSF stability but also to save water.

Jun 29, 2020

By Shiro Ishii

When construction sites are in a densely- populated area or near roads, railroad or river, restrictions upon the ways of handling and using explosives such as dynamite and large demolition equipment are being increasingly stringent, in consideration of environmental pollution such as noise, vibration, dust, flyrocks etc., and safety precaution. In view of this, the development of safe and pollution-free technology for demolishing rocks at mines and reinforced concrete structure at building sites is strongly required. To meet such requirements, the demolition by means of expantion of mineral substances has been considered long before. Recently with the demolition technique using non-explosive demolition agent developed by ONODA CEMENT CO., LTD., holes are drilled into substances to be demolished, such as rocks and concrete before-hand. Then, slurry of such agent mixed with an appropriate quantity of water is poured into the holes. It hardens and expands with the passage of time, and the expansive stress reaches more than 3m/m2 in 10 to 24 hours. This expansive stress causes the material to crack. In this article, descriptions of the non- explosive demolition agent, BRISTAR manufactured by ONODA CEMENT CO., LTD., TOKYO, JAPAN, are given briefly with regard to its physical and chemical properties and its method of use; and the way it is used at an actual construction site is reported.

Jan 1, 1982

By Ben W. Burdett

The operation of an electrolytic refining tank house is an art as well as a science. If the electro-refining industry is to progress, a better understanding of the refining process is necessary. This would help to reduce the amount of training necessary to produce competent tank house operators who, in turn, would be able to increase both quantity and quality of the tank house product. To aid in understanding this process, quantitative relationships between the critical tank house variables must be established. The inherent major contributor to inefficiency in most tank houses is short circuits. By quantifying the effect of short circuits on each of the other variables in the system, as well as their effect on over- all system performance, better decisions regarding manpower allocation can be made. Current distribution under short circuit conditions, which has always been somewhat of a mystery, can be studied in detail. The relative importance of electrolyte balance, proper anode-cathode spacing, low contact resistance at points of electrical connection, and other system variables can be determined, With a better understanding of these variables, the steps necessary to increase current efficiency are more easily defined. Relationships between most of these variables are described in qualitative terms in the literature, but quantitative relationships between tank house variables have never been established. A realistic mathematical model of the tank house could be used to test the effect of variations in a single variable on other variables in the system, and thus define the quantitative relationships between tank house variables. It is not the purpose of this paper to establish these relationships, but to describe a recently developed model that can assist in their establishment. A computer program implementing this model has been applied to examine the effect of short circuits on overall current distribution. Some of the results are given here as examples of the utility of this program.

Jan 1, 1973

By J. J. Gusek

Several final pits in the Seneca No. 1 Surface Coal Mine were abandoned in the 1960's without being reclaimed. In addition, a progressive landslide aggravated by the abandoned mine land conditions was threatening a county road and private property. An AML-funded project to stabilize the landslide and reclaim the final pits was completed in 1986 for the Colorado Division of Mines and Geology (formerly Colorado Mine Land Reclamation Division). The site was visited after ten growing seasons. The land is stable and the vegetation re-establishment is strong. Volunteer native plant species are now invading the reclaimed sites.

Jan 1, 1997

By J. A. Organiscak

Enclosed cab filtration systems are typically used on mobile mining equipment to reduce miners? exposure to airborne dusts and diesel particulates generated during mining operations. Various filter configurations can be used within the heating, ventilation, and air conditioning (HVAC) systems of cabs to remove the airborne contaminants. The air cleaning performance of cab filtration systems is highly dependent on the efficiency of the air filters, the number of filters used, and their placement within the HVAC system. This paper shows how to mathematically model cab filtration systems and illustrates a methodology for developing other cab filtration system design models. Node diagrams of several filtration system circuits are illustrated with their mathematical models at steady state airflow and concentration conditions. Laboratory and field data are presented to demonstrate the validity and utility of modeling enclosed cab air cleaning performance. The paper concludes that incorporating multiple filters throughout the HVAC system improves the air cleaning performance and robustness of the cab filtration system design.

Feb 23, 2014

By F. Stanley, A. Noble, G. Luttrell

"The supply chain for coal-fired power stations involve a multi-stage network of mining units, preparation plants, blending facilities and transportation systems. Attempts to optimize the supply chain have historically been difficult due to the lack of communication/coordination between the various groups involved in coal production, transportation and utilization. In light of this issue, a new approach for globally optimizing the coal supply chain called Micro-Price Optimization has been developed to simplify the optimization problem and to provide coal producers with fundamental insight needed to improve the profitability of their operations. This fundamental concept assigns unit values to each particles (or groups of particles) passing through production units. Optimization occurs whenever the maximum tonnage of positive value particles are recovered and passed to market, while the minimum tonnage of negative value particles are recovered. Elements considered by the concept include factors such as target boiler cost/efficiency, waste disposal costs, coal quality parameters, emission penalties, transportation charges, or other quantifiable impact factors. This article reviews the basis for the micro-price concept and provides a detailed industrial case study involving the determination of optimum coal qualities that need to be supplied by mine operators to feed a coal-fired power station. INTRODUCTION The performance of coal preparation plants have long been known to play an important role in determining the overall profitability of mining operations. This significance is due to the fact that the misplacement of just 1 ton/hr of clean coal to reject resulting from poor plant performance can represent nearly $300,000 per year in lost revenues for a mine producing a steam market coal (i.e., 1 ton/hr x $50/ton x 6,000 hr/yr = $300,000/yr). This loss can be even more pronounced, occasionally approaching $1 million per year for each 1 ton/hr of misplaced clean coal, for operations producing high-quality coking coal products sold into the premium metallurgical market (i.e., 1 ton/hr x $150/ton x 6,000 hr/yr = $900,000/yr). Detailed economic studies indicate that improvements in plant yield resulting from increases in organic efficiency have one of the largest overall impacts on mine revenue when compared to other cost centers within the mining operation. One of the first studies to show this important financial impact was reported by Norton-Hambleton Consultants (Norton, 1979). Their study indicated that an unfavorable change in plant efficiency was second only to coal transportation in terms of its impact on profitability, while an unfavorable change in the cost of underground mining was a distance third. This longstanding realization has continued to provide a strong financial incentive for coal producers to optimize the separation efficiency of their coal processing and blending operations."

Jan 1, 2015

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By Henry Chajet

Good morning, it is truly an honor to have been invited to speak before you today Before I begin my update on MSHA's activities, I?d Like t o quickly say a few words about the American mining congress and its mission in Washington, AMC is a national trade association representing most of the producers of the nation's metals, nonmetals and coal, we also represent the manufacturers of mining equipment and supplies and the financial and consulting institutions which service the mining industry. It is the diversity of our representation which gives us our greatest strength in our petitioning efforts, the administration and the members of congress know that an AMC position is the result of the careful consideration of a vastly diverse group of mining concerns. Our president, Al Overton, perhaps has the best description of AMC when he speaks of us as "the mining industry's eyes and ears and its collective voice in Washington."

Jan 1, 1981

By G. Bourque

Early in the design stage of their new concentrator for the Mount Wright Plant, Quebec Cartier Mining decided to use a process computer for total control of crushing, grinding and concentrating. A map of the area is given in figure 1 and a view of the plant in figure 2. Although the use of process computers is not a new idea in petrochemical and chemical industries, their use in the mining industry is very limited. We innovated in using the computer, not only for data logging, as we have seen in some other plants, but a sole operator located in the administration building, starts and stops mill lines, crushers, load-out system, tailings, thickeners, etc ... by means of a CRT console. Our process is fairly simple as can be seen on the schematic process flow diagram (figure 3). .The ore, carried by 136t diesel electric trucks, is dumped through ore pockets onto two primary pan feeders. The feeders supply two 1,52mx2,79m gyratory crushers which reduce the ore to minus 20,32 cm. Each crushing line have a capacity of 5600t per hour and feed a shuttle conveyor distributing the crude ore into six silos.

Jan 1, 1979

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Saturn light that significantly improves illumination for roof-bolting machine operators while reducing glare. The existing roof-bolter lighting was the baseline and was compared to the Saturn at 100, 75 and 50 percent intensities. Discomfort glare and disability glare were measured by the De Boer rating scale and the Mars Letter Contrast sensitivity test, respectively. Thirty study participants were tested. Discomfort glare was reduced at least three levels with the Saturn luminaire. Visibility levels were four to 6.5 times better with the Saturn than with the baseline. The Saturn design is freely available for commercialization.

By F. Alsobrook

Coleman Quartz Inc. has a long history as the sole U.S. producer of lascas for the cultured quartz growing industry based on its unique deposits in Arkansas. Since 1989 the company has also been producing metallurgical grade silica for the ferrosilicon industry from a deposit of unusually pure Arkansas novaculite. This paper chronicles Coleman's trans-formation of an abandoned railroad ballast quarry into a generator of $1.5 million in annual sales to a nontraditional novaculite market. Potential additional applications for this high quality silica rock will also be mentioned.

Jan 1, 1992

By G. Soni

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model has been validated in a series of laboratory batch flotation experiments, in which mono-sized glass beads are used as feeds. The experimental results are in good agreement with model predictions both in terms of grade and recovery.

Feb 23, 2014

By J. Noll, D. Yantek, J. Organiscak

The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variablefrequency- drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that it could clean a portion of the section return air and provide dust reduction of about 50 percent at the face area downstream of the continuous-miner operation.

Jan 1, 2016

By David G. Kidd

The principles of Ore Sorting in general and photometric sorting in particular are discussed with detailed reference to the Model 16 machine. The operating principles and design of the Model 16 are discussed and a case study presented to demonstrate the use of sorters to process an industrial mineral. In addition, an economic study is presented, to highlight the benefits of ore sorting, by evaluating the increased revenue that can be achieved using an ore sorter to process a particular ore body.

Jan 1, 1983

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

By Klaydison Silva, Pedro Silva, Letícia Damet

The current situation of the global mining economy is increasingly focused on the utilization of materials previously discarded in the mining process. The waste from the past, through new processing routes, is gaining new contours for use as high-value-added products. The strategic mine planning process has consequently had to adapt to the new economic reality. In standard scenarios, the focus was primarily on mine sequencing aimed at the highest economic return, with all infrastructure allocated as a necessity of mining. This work aims, in strategic planning, to configure and select the best composition of mining structures. The entire Mine-Plant-Waste-Tailings-Products chain will be considered as a factor in the sequencing of a multimine complex, to achieve the most sustainable utilization of the current mines’ waste. The sequencing is based on concurrent flows of process configurations and capacities, structure sharing, and flexibility of feed types. These factors will guide the sequencing, which will be constrained by components such as waste and tailings disposal rates, lithology feed relationships, and especially product composition through market specifications, all while respecting product shipping capacities.

Feb 22, 2026

By E. J. Hammer

In the crushing and grinding of metallics for beneficiation, the sizing is normally done to liberate the metals or sulphides for further processing to improve recoveries of the basic metals or minerals. The objective is to reduce the ore in size through various closely controlled stages to that degree of fineness which gives an economic liberation of valuable mineral, but which avoids as much as possible the production of sliming fractions. A different philosophy applies to the crushing and grinding of Gypsum. Our requirements normally demand controlled grinding and/or crushing of the material not only to a fineness suitable for further processing of the mineral into end products, but to produce various sizes of material which are them- selves saleable products. The majority of our tonnage ultimately ends up in stucco for Wallboard. Therefore, our mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off inter- mediate products to meet various Customer requirements. This forces us into compromises at times in our equipment installations, and our equipment must sometimes be more versatile and complex than we would like it to be. We try to process our basic rock, Gypsum, for the most efficient size reduction. We market 5 to 6 different sizes intermediate to the end product, which generally is the fineness of material to be used for stucco for Wallboard, and we do this with controlled crushing, grinding and sizing cycles of the material. To summarize, we use a different philosophy of crushing and grinding than the metallic field which uses comminution or crushing and grinding to improve recovery, whereas we choose our equipment to crush and grind primarily for product performance.

Jan 1, 1969

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016