Search Documents

By Oscar H. Lentz

During 1960, the controversy over percentage depletion reached the level of debate between presidential candidates. Nixon took the position that he would not tamper with the status quo in this matter. Kennedy took the position that he was willing to take a fresh look at the issues involved. Kennedy's position appears to have been based upon two premises: (1) new sources of federal revenue may be needed; and (2) current depletion rates, even if sound in principle, may be too high and, therefore, inequitable. The latter premise constitutes the basis for the claims that depletion allowances are simply "loopholes" of tax avoidance. Very probably the controversy over percentage depletion will remain in the political limelight during most of the coming decade. It is quite possible that the current depletion rates, at least those for oil and gas, will be reduced during this period. The aim of this paper is to isolate the complex causes of this mounting opposition to percentage depletion.

Jan 1, 1961

By David J. Dunn

Mill liner design is an important factor in grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, liner life, and liner wear rate At a time when mill avilability is at a premium, production costs are going up, and lead time for mill liner castings is a year or more, the mill liner that grinds best, lasts longest, and costs least is a necessity for economic mill operation. In testing four mill liner profiles for 13' x 12' overflow ball mills, Climax found that an improved design increased mill tonnage by 3 tons per hour while reducing finish grind by 1.7% + 100 mesh, reduced liner wear rate, and almost doubled liner life.

Jan 1, 1976

By M. J. DeMarco

Beginning in late 1985 and continuing through 1987, Bureau of Mines personnel investigated longwall chain pillar and entry design in two-and three-entry gate-road systems at a deep underground coal mine located in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau of Mines hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in roof falls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1988

By L. T. Larson

Had the blank on the Abstract form been sufficiently spacious a more appropriate title for this paper would be: Neogene Tectonism, Magmatic Activity and Hydrothermal Precious Metal Mineralization in Anatolian Turkey; an Analog with the Basin and Range Province of the Western U.S.? Like the alternative title no thing in Turkey is simple. Its history is long and convolute; its culture fascinating; its metallogeny diverse and its geology very complex. This paper will focus only on the geology of western' Anatolia and the precious metal potential of this third of Turkey. The argument is in the article but to save the reader time and suspense I'll put my conclusions up front- the potential is great and the possibilities exciting.

Jan 1, 1989

The Gosowong epithermal quartz-adularia vein, in the Halmahera magmatic arc, is a new discovery in an area of primary tropical rain forest with no history of gold mining or mineralization. The newly recognized mineral district also contains a number of other epithermal vein systems, two centres of porphyry Cu-Au mineralization, and a number of argillic and advanced argillic alteration zones that may be related to underlying mineralization. Gosowong was discovered and tested through the application of basic exploration techniques including drainage sampling, soil sampling, trenching, magnetics, IP, and diamond drilling. Lapse time from the initial reconnaissance discovery of a stream sediment anomaly to the release of inferred resource estimates of approximately 1.0m ounces was just over 3 years.

Jan 1, 1997

By Herbert P. Haschke

I. Changes made by the Economic Recovery Tax Act of 1981 (ERTA) which have an effect on investing in tax shelter investments A. Maximum ordinary income tax rate on individuals is now 50%. B. Maximum tax rate on long-term capital gains for individuals is now 20%. C. Maximum tax rate on alternative minimum taxable income for individuals is now 20%. D. Although not changed, the "add-on" 15% minimum tax on tax preference items and the possibility of paying the alternative minimum tax cause individual U.S. income tax planning to continue to be very complex. II. Real Estate A. The new Accelerated Cost Recovery System of depreciation (ACRS). 1. Mandatory for assets placed in service after 1980. ACRS will eliminate most if not all controversies with the IRS over depreciation. 2. Real property now depreciated over 15 years. Component depreciation is not available. 3. Accelerated depreciation is available - a 175% declining balance method with an automatic shift to straight line method at the optimum point in the asset's life. Alternatively, a taxpayer can elect to use the straight line method.

Jan 1, 1982

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017

By R. L. Hudak, R. F. Randolph, A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. The National Institute of Occupational Safety and Health (NIOSH) has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by nine decibels. The “Inquiring Ears Want to Know” fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By William C. McBee

A sulfur concrete technology has been developed by the U.S. Department of the Interior, Bureau of Mines, in which chemically modified sulfur is utilized with suitable mineral aggregates to produce construction materials which are resistant to corrosion by acids and salts. This report presents a summary of the basic technology and results of testing the materials under actual operating conditions in 50 corrosive environments in 40 commercial plants. After 4 years of testing, there was essentially no evidence of material degradation or loss of strength. Regular concrete materials were attacked and in some cases completely destroyed under the same conditions. Testing is continuing to establish ultimate longevity and durability of the sulfur concretes. The materials are finding widespread applications in metallurgical, chemical, and fertilizer processing plants.

Jan 1, 1983

By David Newman

"Horizontal stress can have a profound effect on the stability of an underground limestone mine. The presence of horizontal stress is usually determined once the mine has been developed and the orientation of headers and crosscuts are well established. Multiple attempts are typically made to control roof falls without re-orienting the mine. Once the decision has been made to change the orientation, pillar centers, mine opening widths, and the question of how to determine the correct orientation must be answered.A case history is presented to illustrate how geologic structure, ground conditions and roof falls in adjacent mines, the World Stress Map (Heidbach et al., 2016), in-mine measurement of “cutter” roof orientation, the orientation of strata offset (cats eyes) within borescope holes, and the diametral deviation method of determining horizontal strain from drill core were used to establish the most likely range of horizontal stress.The main headers were re-orientated in a direction parallel to the median of the range of horizontal stress. The crosscuts were angled 60° to the headers to avoid being perpendicular to the horizontal stress direction. Pillar centers and opening widths were increased in the favorable stress direction of the mains and decreased in the less favorable crosscut orientation. The major principal horizontal stress magnitude was estimated using the strain measurements from the diametral deviation method and elastic modulus obtained through testing.INTRODUCTIONOver the past decade, there has been a significant increase in the number of underground stone mining operations in the United States. As stripping ratios at surface quarries become uneconomical and reach the extent of the mineral boundary, coupled with the encroachment of urban development on previously rural mining operations, the remaining mine reserves are best accessed through underground development.Although the majority of underground limestone mines in the Midwest are in relatively flat lying deposits with minimal geologic structure, many Appalachian mines are in folded and faulted environments. Tectonic horizontal stresses associated with multiple orogenic episodes are locked in the formation and are released as the underground mine is developed.A common misconception is that horizontal stress impacts are more prevalent at shallow depths where the ratio of horizontal to vertical stress may be high. However, field observations and academic research indicates that horizontal stress conditions may be encountered at any depth due to the tectonic compression of the limestone formation (Esterhuizen et al., 2007; Dolinar and Esterhuizen, 2007; Iannacchione et al., 2003; Slaker, Murphy, and Miller, 2017; Kuhnhein and Ramer, 2004). This paper outlines mine design and layout guidelines for the mitigation of horizontal stress impacts on underground stone mining operations through a case history example. This approach to mine planning and the ability to anticipate horizontal stress can significantly improve future production of multiple levels (Newman and Newman, 2019). As underground stone production continues at deeper depths and in more geologically and geometrically complex mining conditions, an emphasis on ground control and the anticipation of horizontal stress can provide safer and more productive single and multiple level mining operations."

Jan 1, 2019

By Girish Roy, Robert Goodfellow, Angel Del Amo, Bingzhi Yang

Designing and constructing tunnels in seismic prone areas present unique challenges to both designers and contractors. The Westside Purple Line Extension Project– Section 3 in Los Angeles requires crossing an active fault that may subject the tunnels to extreme structural demands. In order to ensure that the linings will safely accommodate the fault movement, a revolutionary composite section—steel plate embedded in the intrados of the precast concrete segmental tunnel lining was finally selected. Additionally, continuous expansion steel plates over the circumferential joints will be installed to mitigate the potential opening of the circumferential joints.

Jun 13, 2021

By William Hodder, Ehsan Alavi, Muhib Hussain

Disc Cutter Wear is influenced by several geological and technical factors and excessive wear can have a major impact on the excavation efficiency of Tunnel Boring Machines (TBM). Disc cutter replacement events cause a disruption to the construction schedule and costs, and should be minimized throughout the project to the extent possible. A well-executed cutterhead inspection and maintenance plan can help mitigate abrupt cutterhead interventions and reduce its effect on project schedule and cost. This paper examines cutterhead inspection and disc cutter replacement events as well as subsequent wear data recorded in the first 7km of the 10.3 km long, 6.3 m diameter Coxwell Sanitary Bypass Tunnel (CBT) project in Toronto, Ontario. The CBT alignment is mainly through Georgian Bay Formation shale.

Dec 1, 2022

By Thomas M. Lynberg

WIDCO is a surface coal mine located near Centralia, Washington. The WIDCO preparation plant processes over 7 million tons of run- of-mine coal each year with a product yield averaging 72%. In the jig type preparation plant the fine refuse amounts to approximately 130 dry tons per hour of 28mesh by 0. This fine refuse material is thickened in a 160ft. diameter static thickener with the use of lime as a coagulant and organic polymer as a flocculant. Once thickened the fine refuse, which is predominately bentonitic clays, has been dewatered and disposed of using several different methods. These methods will be discussed and include vacuum disc filters, ponds, solid bowl centrifuges, belt filter presses and experiments with electrokinetic dewatering.

Jan 1, 1981

By C. Hansen, J. Killey

This paper discusses the replacement of AEROFLOAT ® 1 25 promoter by AERO ® 5688 promoter at Sonora Mining Corp.'s California Mother Lode concentrator. Flotation concentrate is trucked 120 miles to a leach plant in Nevada, so the reduced mass resulting from higher gold grades and reduced talceous gangue and barren pyrite resulting from this change in promoters has brought about a major decrease in shipping costs. Preliminary laboratory testing indicated that free milling gold and controlled amounts of pyrite could be floated using Aero 5688 promoter with reduced dosages of Aero 350 xanthate.2 Extensive plant trials confirmed that the new reagent suite could indeed maintain gold recoveries while reducing total mass. Improved froth characteristics also improved operating flexibility in treating various ore types, and overall reagent costs have been reduced.

Jan 1, 1991

By S. K. Kawatra, H. J. Haselhuhn

"Thickening is used during two primary mineral processing operations: water removal and desliming. During water removal, the pulp density is increased through the injection of flocculants. These flocs settle and create a dense pulp while clarified water is removed through the overflow. During desliming, fine particles are removed through the overflow. Desliming can also be used as a mineral separation process known as selective flocculation-dispersion, where valuable minerals are flocculated and gangue minerals remain dispersed and exit through the overflow.There are many ways to analyze thickener performance on a laboratory scale, but these analyses often do not correlate well with full-scale performance. Some pilot-scale systems have been designed using a semicontinuous approach, but the amount of material required to perform their tests can make semicontinuous pilot thickeners impractical for most applications. This paper focuses on the design and optimization of a continuous pilot-scale deslime thickener that requires minimal material to operate. The design, optimization strategy, and an example study of reagent selection are demonstrated. IntroductionMany laboratory methods have been employed to size and optimize thickener performance. The most common of these include the Coe and Clevenger method and methods derived from the Kynch theory of sedimentation. The Coe and Clevenger method was developed in 1916 and was proven for slurries that do not require flocculation to settle. This method proposed that the settling rate of the pulp is only a function of the solids concentration. It is executed by creating slurries of several different concentrations of solids and performing bench-scale settling tests in graduated cylinders. For each concentration, a thickener unit area can be determined using the following equation (Coe and Clevenger, 1916; Laros, Slottee and Baczek, 2002):"

Jan 1, 2017

By Lester G. Rollins

Coal today enjoys a dominant position, serving the energy and metallurgical marketed The measure of success in the market place is, and will continue to be, the price per million BTUs or price per ton delivered to the user. The Coal Industry's remarkable record of price stability since World War II is well known. The next twenty years promise to be equally as challenging. This challenge will be met our president, Mr. Drain, has often stated that, ?The Joy Manufacturing Company is betting that coal will meet the challenge.? To this end, the resources of Joy have been committed to doing its part. Joy's efforts are directed toward a target which has been defined as: 1. Deliver coal to the user at a price of $.15/MBTU or less. or; 2. Deliver coal to the mine portal at a cost of $1.00 or less.

Jan 1, 1966

By Paul O. Knorr

The Bureau of Ocean Energy Management (BOEM), a bureau within the U.S. Department of the Interior, has responsibility over both energy and non-energy mineral development on the United States Outer Continental Shelf (OCS) under the OCS Lands Act (“OCSLA”). BOEM’s Marine Minerals Program (MMP) manages federal offshore mineral deposits through non-competitive, negotiated agreements for sand and gravel (“sand”) used in coastal restoration efforts and the competitive leasing of critical and hard economic minerals (“critical minerals”). As the steward of OCS critical minerals, BOEM MMP is responsible for understanding where critical minerals are located, identifying and understanding their environments, managing activities that affect these resources, and implementing pertinent federal policies. Fulfilling these responsibilities involves the collection and analysis of environmental, geological, and geophysical data; supporting the science needed to understand the impacts of resourcerelated authorized activities on the biological, physical, and sociocultural environments; encouraging emerging technologies that can reduce the environmental impact of activities; and communicating with stakeholders to foster an understanding of existing federal regulations and potential needs to revise the legal framework. Four U.S. federal rules in the Code of Federal Regulations (CFR) currently inform MMP’s procedures: 30 CFR 580 (prospecting for minerals), 30 CFR 581 (leasing of minerals), 30 CFR 582 (operations in the OCS related to minerals), and 30 CFR 583 (negotiated noncompetitive agreements for sand). Other federal laws and regulations are also pertinent, particularly those supporting the National Environmental Policy Act, Endangered Species Act, National Historic Preservation Act, Marine Mammal Protection Act, Coastal Zone Management Act, Clean Air Act, Federal Water Pollution Control Act, and Magnuson Stevens Fishery Conservation and Management Act.

Feb 22, 2026

By Garry M. Hughes

Lynn lake, Manitoha, where Sherritt has operated a copper-nickel mine since 1954, is located north of the 56th parallel approximately SOO miles north of Winnipeg. Sherritt's new, 3,000 tpd, copper-zinc Fox Mine is situated 30 miles southwest of Lynn lake. This paper focuses on the Fox Mine concentrator, hut first some background information. Sherritt Gordon Mines Limited started mining operations as a copper-zinc producer in 1931 at Sherridon, Manitoba, 150 miles south of Lynn Lake. As Sherridon fizzled out development of a series of nickel-copper orebodies commenced at Lynn Lake. The Forward process was developed to treat the nickel concentrate from the Lynn concentrator. Sherritt's ammonia leaching process is now history and is expected to gain more prominence as pressure is applied to the mining industry for closer environmental control. But few are aware of the fact that the present Lynn Lake crushing plant and concentrator were dismantled in the autumn of 1951 and freighted from Sherridon by tractor train during the winters of 1952 and 1953. The copper-zinc orehody at Fox Mine was discovered early in 1961 by geophysical methods which included both airborne and ground surveys. It is part of a ,large body of massive and semi-massive sulphides consisting chiefly of pyrite; with chalcopyrite, sphalerite (containing 7-9% iron) and pyrrhotite in varying proportions which occur within a series of volcanic and sedimentary rocks. The total mineralized zone is a lenticular body with a minimum average length and width of 1,350 feet and 66 feet respectively, to the explored depth of 2,000 feet. The average sulphide content is 67%. Higher zinc zones are masses of pyrite grains cemented by sphalerite with lower than average copper content. Zones higher in copper and lower in zinc are slightly more quartzose. Gold and silver are present in small amounts roughly proportional to the copper content.

Jan 1, 1971

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"The U.S. National Institute for Occupational Safety and Health completed a 15-month study at an underground limestone mine crusher booth that evaluated three research parameters: (1) the effectiveness of a filtration and pressurization system for improving the air quality inside the operator booth, (2) the relative effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) the performance of three different cab pressure monitoring devices. The protection factor was quantified monthly using particle counters in the respirable dust range of 0.3 to 1 µm particle size, and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static (closed-door) conditions, the filtration unit offered a gravimetric calculated protection factor between 10 and 31, depending on the filter type and loading condition. The monthly particle counting analysis shows that the ? > 95 filter offers a protection factor nearly five times that of the ? > 99 filter, where n = 15 samples. The booth pressure monitors were tested and proved to be a valid indicator of system performance over time. IntroductionDesigned and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from noise and physical hazards, such as flying rock and debris, as well as a more comfortable environment in regards to temperature and humidity (Organiscak et al., 2016). While it is easy to quantify the operation of a cab’s air-conditioning unit by measuring the temperature, or observe whether the cab offers protection from flying debris, it is somewhat more difficult to quantify its performance in reducing respirable dust hazards.The U.S. National Institute for Occupational Safety and Health (NIOSH) has been conducting applied research to improve the air quality inside the enclosed cabs of mobile equipment, resulting in the mathematical modeling of enclosed cab filtration systems (Organiscak and Cecala, 2008). The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms (Noll, Cecala and Hummer, 2015). While stationary enclosures are similar to mobile cabs, the work area can be significantly larger. Workers in booths and control rooms also tend to stay within the enclosure for a greater percentage of the day as opposed to workers on mobile equipment who enter and exit frequently."

Jan 1, 2018

By R. E. Brewer

Pilot scale flotation tests were conducted with a 1-ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pct of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated using the column. The tailings were first water leached at approximately 600 C, and the water-leached tailings, which contained approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH and sodium sulfide addition on gold flotation recovery and redox potentials were examined. maximum gold recovery, 36 pct, was achieved at pH 8.5 with a sodium sulfide addition of 0.18 lb/st.

Jan 1, 1989